| Age | Commit message (Collapse) | Author |
|---|
|
If the PHY has been configured to allow pause frames, then the MAC
should be configured to generate and/or accept those frames.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pause frames are used to enable flow control. A MAC can send and
receive pause frames in order to throttle traffic. However, the PHY
must be configured to allow those frames to pass through.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This improves UDP spreading, and also slightly improves GRO performance
of encapsulated TCP on 7000 series NICs.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mlx5 HW, encapsulation is offloaded by the steering rule having
index into an encapsulation table containing the entire set of headers
to be added by the HW. The driver sets these headers in a buffer when we
are offloading the action.
The code maintains mlx5_encap_entry for each encap header it has
encountered when attempted to offload TC tunnel set action.
This entry maintains a linked list of all the flows sharing the same
encap header, when the last flow is removed from the list the encap
entry is removed.
The actual encap_header is allocated by the driver in the hardware only
if we have layer two neighbour info when the encap entry is created.
While the flow is in the driver, the driver holds a reference on the
neighbour.
When a new flow with encap action is inserted, the code first checks if
the required encap entry exists according to the tunnel set parameters.
If it does the encap is shared, otherwise a new mlx5_encap_entry is
created.
TC action parsing implementation in the driver assumes that tunnel set
action is provided in the same order set by the user, e.g before the
mirred_redirect action.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By implementing this ndo, the host stack will set the vxlan udp port
also to VF representor netdevices. This will allow the TC offload code
in the driver when it gets a tunnel key set action to identify the UDP
port as vxlan, and hence the rule will be a candidate for offloading.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enhance the parsing of offloaded TC rules to set HW matching on outer
(encapsulation) headers.
Parse TC tunnel release action and set it as mlx5 decap action when the
required capabilities are supported.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support steering rules which add encapsulation headers,
encap_id parameter is needed.
Add new mlx5_flow_act struct which holds action related parameter:
action, flow_tag and encap_id. Use mlx5_flow_act struct when adding a new
steering rule.
This patch doesn't change any functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating flow tables, allow the caller to specify creation flags.
Currently no flags are used and as such this patch doesn't add any new
functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of comparing to a const value, check the value of max encap
header size capability as reported by the Firmware.
Fixes: 575ddf5888ea ('net/mlx5: Introduce alloc_encap and dealloc_encap commands')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The alloc and dealloc encap commands will be used in the mlx5e driver,
as such, declare them in a common header file.
Also, rename the functions: mlx5_cmd_{de}alloc_encap is replaced with
mlx5_encap_{de}alloc.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes regression introduced by patch adding feature flags. It was
already reported and patch followed (it got accepted) but it appears it
was incorrect. Instead of fixing reversed condition it broke a good one.
This patch was verified to actually fix SoC hanges caused by bgmac on
BCM47186B0.
Fixes: db791eb2970b ("net: ethernet: bgmac: convert to feature flags")
Fixes: 4af1474e6198 ("net: bgmac: Fix errant feature flag check")
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We received two reports of BUG_ON in bnad_txcmpl_process() where
hw_consumer_index appeared to be ahead of producer_index. Out of order
write/read of these variables could explain these reports.
bnad_start_xmit(), as a producer of tx descriptors, has a few memory
barriers sprinkled around writes to producer_index and the device's
doorbell but they're not paired with anything in bnad_txcmpl_process(), a
consumer.
Since we are synchronizing with a device, we must use mandatory barriers,
not smp_*. Also, I didn't see the purpose of the last smp_mb() in
bnad_start_xmit().
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 9d2afba058722d40cc02f430229c91611c0e8d16.
The original issue would possibly exist if an external module
tried calling our "ethtool_ops" without checking if it still
exists.
The right way of solving it is by simply doing the check in
the caller side.
Currently, no action is required as there's no such use case.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver uses a union for copying data to & from management firmware
when interacting with it.
Problem is that the function always copies sizeof(union) while commit
2edbff8dcb5d ("qed: Learn resources from management firmware") is casting
a union elements which is of smaller size [24-byte instead of 88-bytes].
Also, the union contains some inappropriate elements which increase its
size [should have been 32-bytes]. While this shouldn't corrupt other
PF messages to the MFW [as management firmware enforces permissions so
that each PF is allowed to write only to its own mailbox] we fix this
here as well.
Fixes: 2edbff8dcb5d ("qed: Learn resources from management firmware")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When moving from typhoon_get_settings to typhoon_getlink_ksettings
in the commit f7a5537cd2a5 ("net: 3com: typhoon: use new api
ethtool_{get|set}_link_ksettings"), we use a local variable supported
but we forgot to update the struct ethtool_link_ksettings with
this value.
We also initialize advertising to zero, because otherwise it may
be uninitialized if no case of the switch (tp->xcvr_select) is used.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of adding hooks inside stmmac_platform it is better to just use
the standard PM callbacks within the specific dwmac-driver. This only
used by the dwmac-rk driver.
This reverts commit cecbc5563a02 ("stmmac: allow to split suspend/resume
from init/exit callbacks").
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the rk_gmac_init() only calls another function move this
function call into probe so rk_gmac_init() can be removed.
Since commit cecbc5563a02 ("stmmac: allow to split suspend/resume
from init/exit callbacks") the init hook is no longer used in
dwmac-rk so this can be removed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the exit hook into a standard driver remove function as
the hook doesn't really buy us anything extra.
Eventually the exit hook will be deprecated in favor of the driver
remove function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use standard PM resume/suspend callbacks instead of the hooks in
stmmac_platform. This gives the driver more control and flexibility
when implementing PM functionality. The hooks in stmmac_platform
also doesn't buy us anything extra.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When there is no existing macvlan port in lowdev, one new macvlan port
would be created. But it doesn't be destoried when something failed later.
It casues some memleak.
Now add one flag to indicate if new macvlan port is created.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add driver for the Internal RMII PHY found in the Amlogic Meson GXL SoCs.
This PHY seems to only implement some standard registers and need some
workarounds to provide autoneg values from vendor registers.
Some magic values are currently used to configure the PHY, and this a
temporary setup until clarification about these registers names and
registers fields are provided by Amlogic.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support PHY switching on Amlogic GXL SoCs, add support for
16bit and 32bit registers sizes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smsc911c driver puts its device into low power state when entering
system suspend. Although it doesn't update the device's runtime PM status
to RPM_SUSPENDED, which causes problems for a parent device.
In particular, when the runtime PM status of the parent is requested to be
updated to RPM_SUSPENDED, the runtime PM core prevent this, because it's
forbidden to runtime suspend a device, which has an active child.
Fix this by updating the runtime PM status of the smsc911x device to
RPM_SUSPENDED during system suspend. In system resume, let's reverse that
action by runtime resuming the device and thus also the parent.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The call to krealloc() in wsm_buf_reserve() directly assigns the newly
returned memory to buf->begin. This is all fine except when krealloc()
failes we loose the ability to free the old memory pointed to by
buf->begin. If we just create a temporary variable to assign memory to
and assign the memory to it we can mitigate the memory leak.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add the missing destroy_workqueue() before return from
mwifiex_add_virtual_intf() in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Marvell p2p device disappears from the list of p2p peers on the other
p2p device after disconnection.
It happens due to a bug in driver. When interface is changed from p2p
to station, certain variables(bss_type, bss_role etc.) aren't correctly
updated. This patch corrects them to fix the issue.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
It is observed that if single tid 6 packet comes among with massive tid 0
packets, tid 6 packet may stay in it's queue and will never be
transmited. This is because wmm.highest_queued_prio will be set to 2
during transmission of tid 0 packets As a result, main work thread
keeps on looping without serving that packet. In this case, if command
has downloaded to firmware, driver doesn't process it's response causing
command timeout.
This patch will reset highest_queued_prio if packets exist in data
queue, and try to find a ra_list for current private.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
wmm.tx_pkts_queued and ralist's total_pkt_count should be updated in
synchronization. They were not correctly updated in
mwifiex_send_processed_packet().
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Support for this debugfs command is available in driver. This patch
adds usage information in README file.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
While copying the vendor_ie obtained from the cfg80211_find_vendor_ie()
to the struct mwifiex_types_wmm_info, length/size was inappropriate.
This patch corrects the required length needed to the
mwifiex_types_wmm_info
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
At couple of places in cleanup path, we are just going through the
skb queue and freeing them without unlinking. This leads to a crash
when other thread tries to do skb_dequeue() and use already freed node.
The problem is freed by unlinking skb before freeing it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When host_sleep_config command fails, we should return an error to
PCIe, instead of continuing (and possibly panicking, when we try to keep
processing a timed-out ioctl after we return "successfully" from
suspend).
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Following is mwifiex driver-firmware host sleep handshake.
It involves three threads. suspend handler, interrupt handler, interrupt
processing in main work queue.
1) Enter suspend handler
2) Download HS_CFG command
3) Response from firmware for HS_CFG
4) Suspend thread waits until handshake completes(i.e hs_activate becomes
true)
5) SLEEP from firmware
6) SLEEP confirm downloaded to firmware.
7) SLEEP confirm response from firmware
8) Driver processes SLEEP confirm response and set hs_activate to wake up
suspend thread
9) Exit suspend handler
10) Read sleep cookie in loop and wait until it indicates firmware is
sleep.
11) After processing SLEEP confirm response, we are at the end of interrupt
processing routine. Recheck if there are interrupts received while we were
processing them.
During suspend-resume stress test, it's been observed that we may end up
acessing PCIe hardware(in 10 and 11) when PCIe bus is closed which leads
to a kernel crash.
This patch solves the problem with below changes.
a) action 10 above can be done before 8
b) Skip 11 if hs_activated is true. SLEEP confirm response
is the last interrupt from firmware. No need to recheck for
pending interrupts.
c) Add flush_workqueue() in suspend handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
So far our core code was calling brcmf_fws_process_skb which wasn't
a proper thing to do. If case of devices using msgbuf protocol fwsignal
shouldn't be used. It was an unnecessary extra layer simply calling
a protocol specifix txdata function.
Please note we already have txdata callback, but it's used for calls
between bcdc and fwsignal so it couldn't be simply used there.
This makes core code more generic (instead of bcdc/fwsignal specific).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On some devices the EEPROMs of Ralink Wi-Fi chips have a default Ralink
MAC address set (RT3062F: 00:0C:43:30:62:00, RT3060F:
00:0C:43:30:60:00). Using multiple of these devices in the same network
can cause nasty issues.
Allow to override the MAC in the EEPROM with (a known good) one set in
the device tree to bypass the issue.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath.git patches for 4.10. Major changes:
ath10k
* allow setting coverage class for first generation cards
* read regulatory domain from ACPI
ath9k
* disable RNG by default
|
|
Virtio 1.0 spec says VIRTIO_F_ANY_LAYOUT and VIRTIO_NET_F_GSO are
legacy-only feature bits. Do not negotiate them in virtio 1 mode. Note
this is a spec violation so we need to backport it to stable/downstream
kernels.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by class_find_device() in
hnae_get_handle() on errors and when later releasing the handle.
Fixes: 6fe6611ff275 ("net: add Hisilicon Network Subsystem...")
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the references taken by bus_find_device() before
returning from emac_dev_open().
Note that phy_connect still takes a reference to the phy device.
Fixes: 5d69e0076a72 ("net: davinci_emac: switch to new mdio")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the references taken by of_get_child_by_name() and
bus_find_device() before returning from cpsw_phy_sel().
Note that holding a reference to the cpsw-phy-sel device does not
prevent the devres-managed private data from going away.
Fixes: 5892cd135e16 ("drivers: net: cpsw-phy-sel: Add new driver...")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from phy_connect() and phy_attach().
Note that both function still take a reference to the phy device
through phy_attach_direct().
Fixes: e13934563db0 ("[PATCH] PHY Layer fixup")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the variant of amac hardware present in the Broadcom
Northstar2 based SoCs. Northstar2 requires an additional register to be
configured with the port speed/duplexity (NICPM). This can be added to
the link callback to hide it from the instances that do not use this.
Also, clearing of the pending interrupts on init is required due to
observed issues on some platforms.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the bgmac driver to allow for phy's defined by the device tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.
Inspired-by: Vikas Soni <vsoni@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
