| Age | Commit message (Collapse) | Author |
|---|
|
Before introducing support for DCB ops we should first make sure we
initialize the relevant parts in the device correctly. Specifically, the
egress scheduling.
The device supports a superset of the 802.1Qaz standard with 4 hierarchy
levels that can be linked to each other in multiple ways and with
different transmission selection algorithms (TSA) employed between them.
However, since we only intend to support the 802.1Qaz standard we
flatten the hierarchies and let the user configure via DCB ops the TSA
and max rate shaper at the subgroup hierarchy (see figure below) and the
mapping between switch priority to traffic class. By default, all switch
priorities are mapped to traffic class 0, strict priority is employed
and max shaper is disabled.
Default configuration:
switch priority 0 ... switch priority 7
+ +
| |
+----------------------------------+
|
+--v--+ +-----+
Traffic Class | | | |
Hierarchy | TC0 | ... | TC7 |
| | | |
+--+--+ +--+--+
| |
+--v--+ +--v--+
Subgroup | SG0 | | SG7 |
Hierarchy | | | |
+-----+ +-----+
| TSA | | TSA |
+-----+ ... +-----+
| MAX | | MAX |
+--+--+ +--+--+
| |
+---------------+----------------+
|
+--v--+
Group | |
Hierarchy | GR0 |
| |
+--+--+
|
+--v--+
Port | |
Hierarchy | PR0 |
| |
+-----+
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of DCB ops we'll have to configure the priority to traffic class
mapping of a port.
Add the QoS Switch Traffic Class Table (QTCT) register, which configures
the mapping between the packet switch priority and traffic class on the
transmit port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are going to introduce support for DCB, so we need to be able to
configure the traffic selection algorithm (TSA) used by each traffic
class (TC), as well as the bandwidth percentage allocated to each TC in
case of ETS.
Add the QoS ETS Element Configuration register, which controls the
above parameters.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In addition to the priority group (PG) buffers in the headroom, the
device enables the allocation of headroom shared buffer, which can
be shared between different PGs.
However, we are not going to use the headroom shared buffer and instead
allow the user to use its size for PGs or the switch's shared buffer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last field of the PBMC register is at offset 0x64 and its size is
0x8, so the correct register's length is 0x6C bytes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When packets ingress the switch they are assigned a switch priority and
directed to the corresponding priority group (PG) buffer in the port's
headroom buffer.
Since we now map all switch priorities to priority group 0 (PG0) by
default, there is no need to allocate the other priority groups during
initialization. The only exception is PG9, which is used for control
traffic.
At minimum, the PG should be able to store the currently classified
packet (pipeline latency isn't 0) and also the packets arriving during
the classification time. However, an incoming packet will not be
buffered if there is no available MTU-sized buffer space for storing it.
The buffer needed to accommodate for pipeline latency is variable and
needs to take into account both the current link speed and current
latency of the pipeline, which is time-dependent. Testing showed that
setting the PG's size to twice the current MTU is optimal.
Since PG9 is used strictly for control packets and not subject to flow
control, we are not going to resize it according to user configuration,
so we simply set it according to worst case scenario, which is twice the
maximum MTU.
In any case, later patches in the series will allow a user to direct
lossless flows to other PGs than PG0 and set their size to accommodate
for round-trip propagation delay.
The above change also requires us to resize the PG buffer whenever the
port's MTU is changed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Buffers in the switch store packets in units called buffer cells. Add a
helper to convert from bytes to cells, so that the actual number of
cells required (result is round up) is returned.
Also, drop the SB (shared buffer) acronym from the BYTES_PER_CELL macro,
as this unit is also used in the ports' buffers and not only the
switch's shared buffer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During transmission, the skb's priority is used to map the skb to a
traffic class, where the idea is to group priorities with similar
characteristics (e.g. lossy, lossless) to the same traffic class. By
default, all priorities are mapped to traffic class 0.
In the device, we model the skb's priority as the switch priority, which
is assigned to a packet according to its PCP value and ingress port
(untagged packets are assigned the port's default switch priority - 0).
At ingress, the packet is directed to a priority group (PG) buffer in
the port's headroom buffer according to the packet's switch priority and
switch priority to buffer mapping.
While it's possible to configure the egress mapping between skb's
priority (switch priority) and traffic class, there is no mechanism to
configure the ingress mapping to a PG.
In order to keep things simple and since grouping certain priorities into
a traffic class at egress also implies they should be grouped the same
at ingress, treat a PG as the ingress counterpart of an egress traffic
class.
Having established the above, during initialization map all the switch
priorities to PG0 in accordance with the Linux defaults for traffic
class mapping.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When packets ingress the switch they are assigned a switch priority
number that dictates the packet's priority group (PG) buffer in the
port's headroom buffer.
Add the Port Prio To Buffer (PPTB) register, which configures the switch
priority to PG mapping.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-04-05
This series contains updates to i40e and i40evf only.
Colin Ian King cleaned up a redundant NULL check which was found by static
analysis.
Anjali enables geneve receive offload for XL710/X710 devices.
Mitch cleans up unused variable in i40e_vc_get_vf_resources_msg().
Fixed the driver to actually be able to adjust VLAN tagging features
through ethtool, as expected. Fixed a problem where VF resets would
get lost by the PF preventing the VF driver from initializing. Also
put users mind at ease by lowering some message levels since many of
these conditions can happen any time VFs are enabled or disabled and
are not really indicative a fatal problems, unless they happen
continuously.
Shannon disables the link polling to lessen the admin queue traffic
especially since the link event mask usage has been fixed recently.
Alex Duyck fixes the i40e and i40evf drivers to correctly update
checksums for frames up to 16776960 in length which should be more than
large enough for all possible TSO frames in the near future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement VXLAN-GPE. Only COLLECT_METADATA is supported for now (it is
possible to support static configuration, too, if there is demand for it).
The GPE header parsing has to be moved before iptunnel_pull_header, as we
need to know the protocol.
v2: Removed what was called "L2 mode" in v1 of the patchset. Only "L3 mode"
(now called "raw mode") is added by this patch. This mode does not allow
Ethernet header to be encapsulated in VXLAN-GPE when using ip route to
specify the encapsulation, IP header is encapsulated instead. The patch
does support Ethernet to be encapsulated, though, using ETH_P_TEB in
skb->protocol. This will be utilized by other COLLECT_METADATA users
(openvswitch in particular).
If there is ever demand for Ethernet encapsulation with VXLAN-GPE using
ip route, it's easy to add a new flag switching the interface to
"Ethernet mode" (called "L2 mode" in v1 of this patchset). For now,
leave this out, it seems we don't need it.
Disallowed more flag combinations, especially RCO with GPE.
Added comment explaining that GBP and GPE cannot be set together.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle VXLAN_F_COLLECT_METADATA before VXLAN_F_PROXY. The latter does not
make sense with the former, as it needs populated fdb which does not happen
in metadata mode.
After this cleanup, the fdb code in vxlan_xmit is moved to a common location
and can be later skipped for VXLAN-GPE which does not necessarily carry
inner Ethernet header.
v2: changed commit description to not reference L3 mode
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will allow to initialize vxlan in ARPHRD_NONE mode based on the passed
rtnl attributes.
v2: renamed "l2mode" to "ether".
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While initializing the phy, the stmmac driver sets the
PHY_IGNORE_INTERRUPT so the PAL won't call the adjust hook
that is needed, on some platforms, e.g. STi, to invoke the glue.
The patch allows the PAL to poll the stmmac_adjust_link just one time
in case of a switch is attached, setting later the PHY_IGNORE_INTERRUPT
flag.
Moving this kind of logic inside the adjust_link it makes sense to
anticipate the check for EEE that will never initialized in this
scenario.
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Garbled output for "ethtool -m ethX", in igb-driven NICs with module /
plugin EEPROM (i.e. SFP information). Each output data byte appears
duplicated.
In igb_ethtool.c, igb_get_module_eeprom() is reading the EEPROM via i2c;
the eeprom offset for each word that's read via igb_read_phy_reg_i2c()
was passed in #words, whereas it needs to be a byte offset.
This patches fixes the bug.
Signed-off-by: Doron Shikmoni <doron.shikmoni@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Message level can be set through ethtool, so deprecate module parameter
which is used to set the same.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Intel i211 LOM PCIe Ethernet controllers' iNVM operates as an OTP
and has no external EEPROM interface [1]. The following allows the
driver to pickup the MAC address from a device tree blob when CONFIG_OF
has been enabled.
[1]
http://www.intel.com/content/www/us/en/embedded/products/networking/i211-ethernet-controller-datasheet.html
Signed-off-by: John Holland <jotihojr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch enables bulk free in Tx cleanup for igb and cleans up the
boolean logic in the polling routines for igb in the hopes of avoiding
any mix-ups similar to what occurred with i40e and i40evf.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We were casting the addr as __beXX and then passing it into le32_to_cpu
because the device expects the MAC address to be in network order even
though the register set is little endian. Instead of casting it as __beXX
we can just cast it as __leXX in order to maintain consistency since the
region of memory is already in little endian order as far as we are
concerned.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Low priority scan handling code which delays or aborts scan
operation based on Tx traffic is removed recently. The reason
is firmware already takes care of it in our new feature scan
channel gap. Hence we should advertise low priority scan
support to cfg80211.
This patch fixes a problem in which OBSS scan request from
wpa_supplicant was being rejected by cfg80211.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
retry_limit has never been used during the life of this driver, so
we may as well remove it as it is redundant.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With current driver, it is observed that a URB is not
completed while the USB disconnect is initiated. Due to
that, the URB completion handler is trying to access
the resource which was freed as a part of USB disconnect.
Managing the URBs with anchor will make sure that all
the URBs are handled gracefully before device gets
disconnected.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ssid is an array of u8, so it can never be null, so the null check on
wl->scan.ssid is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use a more common logging style.
Miscellanea:
o Add specific logging macros for ALGORITHM and INTERFACE types
o Output the messages at KERN_DEBUG
o Coalesce formats
o Align arguments
o Whitespace style adjustments for only these changes
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch reports the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:1960 rtl8812ae_dm_txpower_tracking_callback_thermalmeter() warn: inconsistent indenting
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:455 phy_get_tx_swing_8812A() warn: inconsistent indenting
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:517 phy_get_tx_swing_8812A() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch reports the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:1726 _rtl8723be_phy_path_a_rx_iqk() warn: inconsistent indenting
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2304 _rtl8723be_phy_lc_calibrate() warn: inconsistent indenting
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2609 _rtl8723be_phy_set_rf_power_state() warn: inconsistent indenting
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8723be/rf.c
drivers/net/wireless/realtek/rtlwifi/rtl8723be/rf.c:306 _rtl8723be_get_txpower_writeval_by_regulatory() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch reports the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c:137 rtl8723e_dm_bt_need_to_dec_bt_pwr() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch lists the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8192se/phy.c
drivers/net/wireless/realtek/rtlwifi/rtl8192se/phy.c:648 rtl92s_phy_set_rf_power_state() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch lists the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:371 rtl92ee_rx_query_desc() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch lists the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8192c/dm_common.c
drivers/net/wireless/realtek/rtlwifi/rtl8192c/dm_common.c:243 rtl92c_dm_false_alarm_counter_statistics() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch reports the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8188ee/dm.c
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/dm.c:1140 rtl88e_dm_check_txpower_tracking() warn: inconsistent indenting
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:1906 _rtl88e_phy_lc_calibrate() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch reports the following:
CHECK drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3078 btc8723b2ant_run_coexist_mechanism() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch reports the following:
CHECK drivers/net/wireless/realtek/rtlwifi/pci.c
drivers/net/wireless/realtek/rtlwifi/pci.c:366 rtl_pci_check_buddy_priv() error: we previously assumed 'tpriv' could be null (see line 368)
drivers/net/wireless/realtek/rtlwifi/pci.c:1216 _rtl_pci_init_struct() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The previous patch added an option to rtl8723be to manually select the
antenna for those cases when only a single antenna is present, and the
on-board EEPROM is incorrectly programmed. This patch implements the
necessary changes in the Bluetooth coexistence driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V4.0+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
A number of new laptops have been delivered with only a single antenna.
In principle, this is OK; however, a problem arises when the on-board
EEPROM is programmed to use the other antenna connection. The option
of opening the computer and moving the connector is not always possible
as it will void the warranty in some cases. In addition, this solution
breaks the Windows driver when the box dual boots Linux and Windows.
A fix involving a new module parameter has been developed. This commit
adds the new parameter and implements the changes needed for the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V4.0+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Call netif_carrier_off/on while stoping/starting netdev queues.
This fixes netdev watchdog warning and ->ndo_tx_timeout() invocation
during suspend resume stress test.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Fixes: 54f008497b9f09f ('mwifiex: Empty Tx queue during suspend')
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is an error path where "ret" isn't initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Support for Link Quality measurement (Aviya)
* Improvements in thermal (Chaya Rachel)
* Various cleanups (many people)
* Improvements in firmware error dump (Golan)
* More work 9000 devices and MSIx (Haim)
* Continuation of the Dynamic Queue Allocation work (Liad)
* Scan timeout to cope with buggy firmware (Luca)
* D0i3 improvements (Luca)
* Make the paging less memory hungry (Matti)
* 9000 new Rx path (Sara)
|
|
Sometimes drivers already looked up, or know out-of-band
from their device, which station transmitted a given RX
frame. Allow them to pass the station pointer to mac80211
to save the extra lookup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With IPv4 and IPv6 now using the same format for checksums based on the
length of the frame we need to update the i40e and i40evf drivers so that
they correctly account for lengths greater than or equal to 64K.
With this patch the driver should now correctly update checksums for frames
up to 16776960 in length which should be more than large enough for all
possible TSO frames in the near future.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add the Media Not Available flag to the link event mask. It seems
that event comes first if you have a DA cable pulled out, but there's no
follow-up event for Link Down; if you're not looking for MEDIA_NA you will
get no event, even though there's now no Link.
Change-ID: cb3340a2849805bb881f64f6f2ae810eef46eba7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
These conditions can happen any time VFs are enabled or disabled and are
not really indicative of fatal problems unless they happen continuously.
Lower the log level so that people don't get scared.
Change-ID: I1ceb4adbd10d03cbeed54d1f5b7f20d60328351d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
100baseT/Full is now listed and supported link mode for 10GBaseT PHY.
This is a fix to list all the supported link modes of 10GBaseT PHY.
Change-ID: If2be3212ef0fef85fd5d6e4550c7783de2f915e9
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We were passing in the seed where we should just be passing false
because we want the VSI table not the pf table.
Change-ID: I9b633ab06eb59468087f0c0af8539857e99f9495
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Periodic link polling was added when the link events were found not to be
trustworthy. This was the case early on, but was likely because the link
event mask was being used incorrectly. As this has been fixed in recent
code, we can disable the link polling to lessen the AQ traffic.
Change-ID: Id890b5ee3c2d04381fc76ffa434777644f5d8eb0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Upon module remove, wait a little longer after requesting a reset before
checking to see if the firmware responded. This change prevents double
resets when the firmware is busy.
Change-ID: Ieedc988ee82fac1f32a074bf4d9e4dba426bfa58
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
