| Age | Commit message (Collapse) | Author |
|---|
|
Remove the redundant check of (tg3_asic_rev(tp) == ASIC_REV_5705) after
it is checked to be true.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20211008063147.1421-1-sakiwit@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Similar to commit 6087175b7991 ("net: dsa: mt7530: use independent VLAN
learning on VLAN-unaware bridges"), software forwarding between an
unoffloaded LAG port (a bonding interface with an unsupported policy)
and a mv88e6xxx user port directly under a bridge is broken.
We adopt the same strategy, which is to make the standalone ports not
find any ATU entry learned on a bridge port.
Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are
as many FIDs as VIDs (4096). The FID is derived from the VID when
possible (the VTU maps a VID to a FID), with a fallback to the port
based default FID value when not (802.1Q Mode is disabled on the port,
or the classified VID isn't present in the VTU).
The mv88e6xxx driver makes the following use of FIDs and VIDs:
- the port's DefaultVID (to which untagged & pvid-tagged packets get
classified) is 0 and is absent from the VTU, so this kind of packets is
processed in FID 0, the default FID assigned by mv88e6xxx_setup_port.
- every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() ->
mv88e6xxx_atu_new() associates a FID with that VID which increases
linearly starting from 1. Like this:
bridge vlan add dev lan0 vid 100 # FID 1
bridge vlan add dev lan1 vid 100 # still FID 1
bridge vlan add dev lan2 vid 1024 # FID 2
The FID allocation made by the driver is sub-optimal for the following
reasons:
(a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too.
A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID
of 0 too. The difference is that the bridged ports may learn ATU
entries, while the standalone port has the requirement that it must
not, and must not find them either. Standalone ports must not use
the same FID as ports belonging to a bridge. All standalone ports
can use the same FID, since the ATU will never have an entry in
that FID.
(b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a
default FID of 0 on all their ports. The FDBs will not be isolated
between these bridges. Every VLAN-unaware bridge must use the same
FID on all its ports, different from the FID of other bridge ports.
(c) Each bridge VLAN uses a unique FID which is useful for Independent
VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges
will result in the same FID being used by mv88e6xxx_atu_new().
The correct behavior is for VLAN 1 in br0 to have a different FID
compared to VLAN 1 in br1.
This patch cannot fix all the above. Traditionally the DSA framework did
not care about this, and the reality is that DSA core involvement is
needed for the aforementioned issues to be solved. The only thing we can
solve here is an issue which does not require API changes, and that is
issue (a), aka use a different FID for standalone ports vs ports under
VLAN-unaware bridges.
The first step is deciding what VID and FID to use for standalone ports,
and what VID and FID for bridged ports. The 0/0 pair for standalone
ports is what they used up till now, let's keep using that. For bridged
ports, there are 2 cases:
- VLAN-aware ports will never end up using the port default FID, because
packets will always be classified to a VID in the VTU or dropped
otherwise. The FID is the one associated with the VID in the VTU.
- On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at
zero (just as in the case of standalone ports), and just change the
port's default FID from 0 to a different number (say 1).
However, Tobias points out that there is one more requirement to cater to:
cross-chip bridging. The Marvell DSA header does not carry the FID in
it, only the VID. So once a packet crosses a DSA link, if it has a VID
of zero it will get classified to the default FID of that cascade port.
Relying on a port default FID for upstream cascade ports results in
contradictions: a default FID of 0 breaks ATU isolation of bridged ports
on the downstream switch, a default FID of 1 breaks standalone ports on
the downstream switch.
So not only must standalone ports have different FIDs compared to
bridged ports, they must also have different DefaultVID values.
IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply
choose 4095 as the DefaultVID of ports belonging to VLAN-unaware
bridges, and VID 4095 maps to FID 1.
For the xmit operation to look up the same ATU database, we need to put
VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges
too. All shared ports are configured to map this VID to the bridging
FID, because they are members of that VLAN in the VTU. Shared ports
don't need to have 802.1QMode enabled in any way, they always parse the
VID from the DSA header, they don't need to look at the 802.1Q header.
We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the
mention that mv88e6xxx_vtu_setup() which was located right below that
call was flushing the VTU so those entries wouldn't be preserved.
So we need to relocate the VTU flushing prior to the port initialization
during ->setup(). Also note that this is why it is safe to assume that
VID 4095 will get associated with FID 1: the user ports haven't been
created, so there is no avenue for the user to create a bridge VLAN
which could otherwise race with the creation of another FID which would
otherwise use up the non-reserved FID value of 1.
[ Currently mv88e6xxx_port_vlan_join() doesn't have the option of
specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ]
mv88e6xxx_port_db_load_purge() is the function to access the ATU for
FDB/MDB entries, and it used to determine the FID to use for
VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid().
But the driver only called mv88e6xxx_port_set_fid() once, during probe,
so no surprises, the port FID was always 0, the call to get_fid() was
redundant. As much as I would have wanted to not touch that code, the
logic is broken when we add a new FID which is not the port-based
default. Now the port-based default FID only corresponds to standalone
ports, and FDB/MDB entries belong to the bridging service. So while in
the future, when the DSA API will support FDB isolation, we will have to
figure out the FID based on the bridge number, for now there's a single
bridging FID, so hardcode that.
Lastly, the tagger needs to check, when it is transmitting a VLAN
untagged skb, whether it is sending it towards a bridged or a standalone
port. When we see it is bridged we assume the bridge is VLAN-unaware.
Not because it cannot be VLAN-aware but:
- if we are transmitting from a VLAN-aware bridge we are likely doing so
using TX forwarding offload. That code path guarantees that skbs have
a vlan hwaccel tag in them, so we would not enter the "else" branch
of the "if (skb->protocol == htons(ETH_P_8021Q))" condition.
- if we are transmitting on behalf of a VLAN-aware bridge but with no TX
forwarding offload (no PVT support, out of space in the PVT, whatever),
we would indeed be transmitting with VLAN 4095 instead of the bridge
device's pvid. However we would be injecting a "From CPU" frame, and
the switch won't learn from that - it only learns from "Forward" frames.
So it is inconsequential for address learning. And VLAN 4095 is
absolutely enough for the frame to exit the switch, since we never
remove that VLAN from any port.
Fixes: 57e661aae6a8 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VLAN support in mv88e6xxx has a loaded history. Commit 2ea7a679ca2a
("net: dsa: Don't add vlans when vlan filtering is disabled") noticed
some issues with VLAN and decided the best way to deal with them was to
make the DSA core ignore VLANs added by the bridge while VLAN awareness
is turned off. Those issues were never explained, just presented as
"at least one corner case".
That approach had problems of its own, presented by
commit 54a0ed0df496 ("net: dsa: provide an option for drivers to always
receive bridge VLANs") for the DSA core, followed by
commit 1fb74191988f ("net: dsa: mv88e6xxx: fix vlan setup") which
applied ds->configure_vlan_while_not_filtering = true for mv88e6xxx in
particular.
We still don't know what corner case Andrew saw when he wrote
commit 2ea7a679ca2a ("net: dsa: Don't add vlans when vlan filtering is
disabled"), but Tobias now reports that when we use TX forwarding
offload, pinging an external station from the bridge device is broken if
the front-facing DSA user port has flooding turned off. The full
description is in the link below, but for short, when a mv88e6xxx port
is under a VLAN-unaware bridge, it inherits that bridge's pvid.
So packets ingressing a user port will be classified to e.g. VID 1
(assuming that value for the bridge_default_pvid), whereas when
tag_dsa.c xmits towards a user port, it always sends packets using a VID
of 0 if that port is standalone or under a VLAN-unaware bridge - or at
least it did so prior to commit d82f8ab0d874 ("net: dsa: tag_dsa:
offload the bridge forwarding process").
In any case, when there is a conversation between the CPU and a station
connected to a user port, the station's MAC address is learned in VID 1
but the CPU tries to transmit through VID 0. The packets reach the
intended station, but via flooding and not by virtue of matching the
existing ATU entry.
DSA has established (and enforced in other drivers: sja1105, felix,
mt7530) that a VLAN-unaware port should use a private pvid, and not
inherit the one from the bridge. The bridge's pvid should only be
inherited when that bridge is VLAN-aware, so all state transitions need
to be handled. On the other hand, all bridge VLANs should sit in the VTU
starting with the moment when the bridge offloads them via switchdev,
they are just not used.
This solves the problem that Tobias sees because packets ingressing on
VLAN-unaware user ports now get classified to VID 0, which is also the
VID used by tag_dsa.c on xmit.
Fixes: d82f8ab0d874 ("net: dsa: tag_dsa: offload the bridge forwarding process")
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20211003222312.284175-2-vladimir.oltean@nxp.com/#24491503
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
|
|
This patch fixes below compliation error in case CONFIG_QED_SRIOV not
defined.
drivers/net/ethernet/qlogic/qed/qed_dev.c: In function
‘qed_fw_err_handler’:
drivers/net/ethernet/qlogic/qed/qed_dev.c:2390:3: error: implicit
declaration of function ‘qed_sriov_vfpf_malicious’; did you mean
‘qed_iov_vf_task’? [-Werror=implicit-function-declaration]
qed_sriov_vfpf_malicious(p_hwfn, &data->err_data);
^~~~~~~~~~~~~~~~~~~~~~~~
qed_iov_vf_task
drivers/net/ethernet/qlogic/qed/qed_dev.c: In function
‘qed_common_eqe_event’:
drivers/net/ethernet/qlogic/qed/qed_dev.c:2410:10: error: implicit
declaration of function ‘qed_sriov_eqe_event’; did you mean
‘qed_common_eqe_event’? [-Werror=implicit-function-declaration]
return qed_sriov_eqe_event(p_hwfn, opcode, echo, data,
^~~~~~~~~~~~~~~~~~~
qed_common_eqe_event
Fixes: fe40a830dcde ("qed: Update qed_hsi.h for fw 8.59.1.0")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Micrel KSZ9131 PHY LED behavior is not correct when configured in
Individual Mode, LED1 (Activity LED) is in the ON state when there is
no-link.
Workaround this by setting bit 9 of register 0x1e after verifying that
the LED configuration is Individual Mode.
This issue is described in KSZ9131RNX Silicon Errata DS80000693B [*]
and according to that it will not be corrected in a future silicon
revision.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ9131RNX-Silicon-Errata-and-Data-Sheet-Clarification-80000863B.pdf
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A new helper to detect if a net device name is in use was added. Use it
here as the return reference from __dev_get_by_name was discarded.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A new helper to detect if a net device name is in use was added. Use it
here as the return reference from __dev_get_by_name was discarded.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for driver level TSO in the enetc driver using
the TSO API.
Beside using the usual tso_build_hdr(), tso_build_data() this specific
implementation also has to compute the checksum, both IP and L4, for
each resulted segment. This is because the ENETC controller does not
support Tx checksum offload which is needed in order to take advantage
of TSO.
With the workaround for the ENETC MDIO erratum in place the Tx path of
the driver is forced to lock/unlock for each skb sent. This is why, even
though we are computing the checksum by hand we see the following
improvement in TCP termination on the LS1028A SoC, on a single A72 core
running at 1.3GHz:
before: 1.63 Gbits/sec
after: 2.34 Gbits/sec
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is just a preparation patch for software TSO in the enetc driver.
Unfortunately, ENETC does not support Tx checksum offload which would
normally render TSO, even software, impossible.
Declare NETIF_F_HW_CSUM as part of the feature set and do it at driver
level using skb_csum_hwoffload_help() so that we can move forward and
also add support for TSO in the next patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some old IPs do not provide the hardware feature register.
On these IPs, this register is read 0x00000000.
In old driver version, this feature was handled but a regression came
with the commit f10a6a3541b4 ("stmmac: rework get_hw_feature function").
Indeed, this commit removes the return value in dma->get_hw_feature().
This return value was used to indicate the validity of retrieved
information and used later on in stmmac_hw_init() to override
priv->plat data if this hardware feature were valid.
This patch restores the return code in ->get_hw_feature() in order
to indicate the hardware feature validity and override priv->plat
data only if this hardware feature is valid.
Fixes: f10a6a3541b4 ("stmmac: rework get_hw_feature function")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stephen reported that ath11k was failing to build on m68k and xtensa:
In file included from <command-line>:0:0:
In function 'ath11k_peer_assoc_h_smps',
inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:2362:2:
include/linux/compiler_types.h:317:38: error: call to '__compiletime_assert_650' declared with attribute error: FIELD_GET: type of reg too small for mask
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
include/linux/compiler_types.h:298:4: note: in definition of macro '__compiletime_assert'
prefix ## suffix(); \
^
include/linux/compiler_types.h:317:2: note: in expansion of macro '_compiletime_assert'
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
include/linux/build_bug.h:39:37: note: in expansion of macro 'compiletime_assert'
#define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
^
include/linux/bitfield.h:52:3: note: in expansion of macro 'BUILD_BUG_ON_MSG'
BUILD_BUG_ON_MSG((_mask) > (typeof(_reg))~0ull, \
^
include/linux/bitfield.h:108:3: note: in expansion of macro '__BF_FIELD_CHECK'
__BF_FIELD_CHECK(_mask, _reg, 0U, "FIELD_GET: "); \
^
drivers/net/wireless/ath/ath11k/mac.c:2079:10: note: in expansion of macro 'FIELD_GET'
smps = FIELD_GET(IEEE80211_HE_6GHZ_CAP_SM_PS,
Fix the issue by using le16_get_bits() to specify the size explicitly.
Fixes: 6f4d70308e5e ("ath11k: support SMPS configuration for 6 GHz")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHYLIB device drivers must match by either numerical PHY ID or by their
.match_phy_device method. Matching by DT is not permitted.
Link: https://lore.kernel.org/r/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the MDIO bus, we have PHYLIB devices and drivers, and we have non-
PHYLIB devices and drivers. PHYLIB devices are MDIO devices that are
wrapped with a struct phy_device.
Trying to bind a MDIO device with a PHYLIB driver results in out-of-
bounds accesses as we attempt to access struct phy_device members. So,
let's prevent this by ensuring that the type of the MDIO device
(indicated by the MDIO_DEVICE_FLAG_PHY flag) matches the type of the
MDIO driver (indicated by the MDIO_DEVICE_IS_PHY flag.)
Link: https://lore.kernel.org/r/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coverity complains of an uninitialized variable.
CID 120847 (#1 of 1): Uninitialized scalar variable (UNINIT)
3. uninit_use_in_call: Using uninitialized value *sw_platform_str when calling qed_dump_str_param. [show details]
1344 offset += qed_dump_str_param(dump_buf + offset,
1345 dump, "sw-platform", sw_platform_str);
Fix this by removing dead code that references sw_platform_str.
Fixes: 6c95dd8f0aa1d ("qed: Update debug related changes")
Cc: Ariel Elior <aelior@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shai Malin <smalin@marvell.com>
Cc: Omkar Kulkarni <okulkarni@marvell.com>
Cc: Prabhakar Kushwaha <pkushwaha@marvell.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eliminate the following coccicheck warning:
./drivers/net/dsa/rtl8366rb.c:1348:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new platform_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, net;
@@
- eth_platform_get_mac_address(dev, net->dev_addr)
+ platform_get_ethdev_address(dev, net)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-07
Michal Swiatkowski says:
The following patch series introduces basic switchdev model
support in ice driver. Implement the following blocks of
switchdev framework:
- VF port representors creation
- control plane VSI definition
- exception path (a. k. a. "slow-path") - to allow a virtual
switch or linux bridge to receive any packet that doesn't match
any hw filter
- link state management of virtual ports
- query virtual port statistics
Hardware offload support in switchdev mode is out of scope of
this patchset. Devlink interface is used to toggle between
switchdev and legacy (the default) modes of the driver.
---
Note: This series includes the use enum ice_status, however, we have
patches in our queue to remove it from the driver [1]. We are working
through the patches that precede the removal series.
[1] https://patchwork.ozlabs.org/project/intel-wired-lan/list/?series=265957
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce the following ethtool operations for VF's representor:
-get_drvinfo
-get_strings
-get_ethtool_stats
-get_sset_count
-get_link
In all cases, existing operations were used with minor
changes which allow us to detect if ethtool op was called for
representor. Only VF VSI stats will be available for representor.
Implement ndo_get_stats64 for port representor. This will update
VF VSI stats and read them.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Slow path means allowing packet to go from uplink to representor
and from representor to correct VF on Rx site and from VF to
representor and to uplink on Tx site.
To accomplish this driver, has to set correct Tx descriptor. When
packet is sent from representor to VF, destination should be
set to VF VSI. When packet is sent from uplink port destination
should be uplink to bypass switch infrastructure and send packet
outside.
On Rx site driver should check source VSI field from Rx descriptor
and based on that forward packed to correct netdev. To allow
this there is a target netdevs table in control plane VSI
struct.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As resetting all VFs behaves mostly like creating new VFs also
eswitch infrastructure has to be recreated. The easiest way to
do that is to rebuild eswitch after resetting VFs.
Implement helper functions to start and stop all representors
queues. This is used to disable traffic on port representors.
In rebuild path:
- NAPI has to be disabled
- eswitch environment has to be set up
- new port representors have to be created, because the old
one had pointer to not existing VFs
- new control plane VSI ring should be remapped
- NAPI hast to be enabled
- rxdid has to be set to FLEX_NIC_2, because this descriptor id
support source_vsi, which is needed on control plane VSI queues
- port representors queues have to be started
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Only way to enable switchdev is to create VFs when the eswitch
mode is set to switchdev. Check if correct mode is set and
enable switchdev in function which creating VFs.
Disable switchdev when user change number of VFs to 0. Changing
eswitch mode back to legacy when VFs are created in switchdev
mode isn't allowed.
As switchdev takes care of managing filter rules, adding new
rules on VF is blocked.
In case of resetting VF driver has to update pointer in ice_repr
struct, because after reset VSI related things can change.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
New type of VSI has to be defined for switchdev control plane
VSI. Number of allocated Tx and Rx queue has to be equal to
amount of VFs, because each port representor should have one
Tx and Rx queue.
Also to not increase number of used irqs too much, control plane
VSI uses only one q_vector and handle all queues in one irq.
To allow handling all queues in one irq , new function to clean
msix for eswitch was introduced. This function will schedule napi
for each representor instead of scheduling it only for one like in
normal clean irq function.
Only one additional msix has to be requested. Always try to request
it in ice_ena_msix_range function.
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Switchdev environment has to be set up when user create VFs
and eswitch mode is switchdev. Release is done when user
delete all VFs.
Data path in this implementation is based on control plane VSI.
This VSI is used to pass traffic from port representors to
corresponding VFs and vice versa. Default TX rule has to be
added to forward packet to control plane VSI. This will redirect
packets from VFs which don't match other rules to control plane
VSI.
On RX side default rule is added on uplink VSI to receive all
traffic that doesn't match other rules. When setting switchdev
environment all other rules from VFs should be removed. Packet to
VFs will be forwarded by control plane VSI.
As VF without any mac rules can't send any packet because of
antispoof mechanism, VSI antispoof should be turned off on each VFs.
To send packet from representor to correct VSI, destination VSI
field in TX descriptor will have to be filled. Allow that by
setting destination override bit in control plane VSI security config.
Packet from VFs will be received on control plane VSI. Driver
should decide to which netdev forward the packet. Decision is
made based on src_vsi field from descriptor. There is a target
netdev list in control plane VSI struct which choose netdev
based on src_vsi number.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There is no way to change default lan_en and lb_en flags while
adding new rule. Add function that allows changing these flags
on ICE_SW_LKUP_DFLT recipe and any rule id.
lan_en allows packet to go outside if rule is matched. Clearing
this bit will block packet from sending it outside.
lb_en allows packet to be forwarded to other VSI. Clearing
this bit will block packet from forwarding it to other VSI.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement functions to make setting VSI security config easier.
Main function ice_update_security fills security section field and
checks against error in updating VSI. Reset functions are responsible
for correct filling config according to user expectations.
This helper is needed because destination override is located in
this section. Driver has to set this bit to allow strering Tx packet
on VSI based on value in Tx descriptors.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In switchdev driver shouldn't add MAC, VLAN and promisc
filters on iavf demand but should return success to not
break normal iavf flow.
Achieve that by creating table of functions pointer with
default functions used to parse iavf command. While parse
iavf command, call correct function from table instead of
calling function direct.
When port representors are being created change functions
in table to new one that behaves correctly for switchdev
puprose (ignoring new filters).
Change back to default ops when representors are being
removed.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Port representor is used to manage VF from host side. To allow
it each created representor registers netdevice with random hw
address. Also devlink port is created for all representors.
Port representor name is created based on switch id or managed
by devlink core if devlink port was registered with success.
Open and stop ndo ops are implemented to allow managing the VF
link state. Link state is tracked in VF struct.
Struct ice_netdev_priv is extended by pointer to representor
field. This is needed to get correct representor from netdev
struct mostly used in ndo calls.
Implement helper functions to check if given netdev is netdev of
port representor (ice_is_port_repr_netdev) and to get representor
from netdev (ice_netdev_to_repr).
As driver mostly will create or destroy port representors on all
VFs instead of on single one, write functions to add and remove
representor for each VF.
Representor struct contains pointer to source VSI, which is VSI
configured on VF, backpointer to VF, backpointer to netdev,
q_vector pointer and metadata_dst which will be used in data path.
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Keeping devlink port inside VSI data structure causes some issues.
Since VF VSI is released during reset that means that we have to
unregister devlink port and register it again every time reset is
triggered. With the new changes in devlink API it
might cause deadlock issues. After calling
devlink_port_register/devlink_port_unregister devlink API is going to
lock rtnl_mutex. It's an issue when VF reset is triggered in netlink
operation context (like setting VF MAC address or VLAN),
because rtnl_lock is already taken by netlink. Another call of
rtnl_lock from devlink API results in dead-lock.
By moving devlink port to PF/VF we avoid creating/destroying it
during reset. Since this patch, devlink ports are created during
ice_probe, destroyed during ice_remove for PF and created during
ice_repr_add, destroyed during ice_repr_rem for VF.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Write set and get eswitch mode functions used by devlink
ops. Use new pf struct member eswitch_mode to track current
eswitch mode in driver.
Changing eswitch mode is only allowed when there are no
VFs created.
Create new file for eswitch related code.
Add config flag ICE_SWITCHDEV to allow user to choose if
switchdev support should be enabled or disabled.
Use case examples:
- show current eswitch mode ('legacy' is the default one)
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode legacy
- move to 'switchdev' mode
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode
switchdev
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode switchdev
- create 2 VFs
[root@localhost]# echo 2 > /sys/class/net/ens4f1/device/sriov_numvfs
- unsuccessful attempt to change eswitch mode while VFs are created
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode legacy
devlink answers: Operation not supported
- destroy VFs
[root@localhost]# echo 0 > /sys/class/net/ens4f1/device/sriov_numvfs
- restore 'legacy' mode
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode legacy
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode legacy
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from xfrm, bpf, netfilter, and wireless.
Current release - regressions:
- xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting a new
value in the middle of an enum
- unix: fix an issue in unix_shutdown causing the other end
read/write failures
- phy: mdio: fix memory leak
Current release - new code bugs:
- mlx5e: improve MQPRIO resiliency against bad configs
Previous releases - regressions:
- bpf: fix integer overflow leading to OOB access in map element
pre-allocation
- stmmac: dwmac-rk: fix ethernet on rk3399 based devices
- netfilter: conntrack: fix boot failure with
nf_conntrack.enable_hooks=1
- brcmfmac: revert using ISO3166 country code and 0 rev as fallback
- i40e: fix freeing of uninitialized misc IRQ vector
- iavf: fix double unlock of crit_lock
Previous releases - always broken:
- bpf, arm: fix register clobbering in div/mod implementation
- netfilter: nf_tables: correct issues in netlink rule change event
notifications
- dsa: tag_dsa: fix mask for trunked packets
- usb: r8152: don't resubmit rx immediately to avoid soft lockup on
device unplug
- i40e: fix endless loop under rtnl if FW fails to correctly respond
to capability query
- mlx5e: fix rx checksum offload coexistence with ipsec offload
- mlx5: force round second at 1PPS out start time and allow it only
in supported clock modes
- phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
sequence
Misc:
- xfrm: slightly rejig the new policy uAPI to make it less cryptic"
* tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
net: prefer socket bound to interface when not in VRF
iavf: fix double unlock of crit_lock
i40e: Fix freeing of uninitialized misc IRQ vector
i40e: fix endless loop under rtnl
dt-bindings: net: dsa: marvell: fix compatible in example
ionic: move filter sync_needed bit set
gve: report 64bit tx_bytes counter from gve_handle_report_stats()
gve: fix gve_get_stats()
rtnetlink: fix if_nlmsg_stats_size() under estimation
gve: Properly handle errors in gve_assign_qpl
gve: Avoid freeing NULL pointer
gve: Correct available tx qpl check
unix: Fix an issue in unix_shutdown causing the other end read/write failures
net: stmmac: trigger PCS EEE to turn off on link down
net: pcs: xpcs: fix incorrect steps on disable EEE
netlink: annotate data races around nlk->bound
net: pcs: xpcs: fix incorrect CL37 AN sequence
net: sfp: Fix typo in state machine debug string
net/sched: sch_taprio: properly cancel timer from taprio_destroy()
net: bridge: fix under estimation in br_get_linkxstats_size()
...
|
|
Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20211006181115.GA913499@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20211006180944.GA913477@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/20211006180927.GA913456@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20211006180843.GA913399@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a spelling mistake in an ath11k_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006083217.349596-1-colin.king@canonical.com
|
|
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
First set of patches for v5.16. ath11k getting most of new features
this time. Other drivers also have few new features, and of course the
usual set of fixes and cleanups all over.
Major changes:
rtw88
* support adaptivity for ETSI/JP DFS region
* 8821c: support RFE type4 wifi NIC
brcmfmac
* DMI nvram filename quirk for Cyberbook T116 tablet
ath9k
* load calibration data and pci init values via nvmem subsystem
ath11k
* include channel rx and tx time in survey dump statistics
* support for setting fixed Wi-Fi 6 rates from user space
* support for 80P80 and 160 MHz bandwidths
* spectral scan support for QCN9074
* support for calibration data files per radio
* support for calibration data via eeprom
* support for rx decapsulation offload (data frames in 802.3 format)
* support channel 2 in 6 GHz band
ath10k
* include frame time stamp in beacon and probe response frames
wcn36xx
* enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert a few drivers to device_get_ethdev_address(),
saving a few LoC.
The check if addr is valid in netsec is superfluous,
device_get_ethdev_addr() already checks that (in
fwnode_get_mac_addr()).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new device_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- device_get_mac_address(np, dev->dev_addr, ETH_ALEN)
+ device_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All callers pass in ETH_ALEN and the function itself
will return -EINVAL for any other address length.
Just assume it's ETH_ALEN like all other mac address
helpers (nvm, of, platform).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fwnode_get_mac_address() and device_get_mac_address()
return a pointer to the buffer that was passed to them
on success or NULL on failure. None of the callers
care about the actual value, only if it's NULL or not.
These semantics differ from of_get_mac_address() which
returns an int so to avoid confusion make the device
helpers return an errno.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rob suggests to move of_net.c from under drivers/of/ somewhere
to the networking code.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the mdiobus_modify_changed() helper in the C22 PCS advertisement
helper.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add mdiobus_modify_changed() helper to reflect the phylib and similar
equivalents. This will avoid this functionality being open-coded, as
has already happened in phylink, and it looks like other users will be
appearing soon.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the transceiver module extended state and sub-state
added in previous patch. The extended state is meant to describe link
issues related to transceiver modules.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement support for ethtool_ops::.get_module_power_mode and
ethtool_ops::set_module_power_mode.
The get operation is implemented using the Management Cable IO and
Notifications (MCION) register that reports the operational power mode
of the module and its presence. In case a module is not present, its
operational power mode is not reported to ethtool and user space. If not
set before, the power mode policy is reported as "high", which is the
default on Mellanox systems.
The set operation is implemented using the Port Module Memory Map
Properties (PMMP) register. The register instructs the device's firmware
to transition a plugged-in module to / out of low power mode by writing
to its memory map.
When the power mode policy is set to 'auto', a module will not
transition to low power mode as long as any ports using it are
administratively up. Example:
# devlink port split swp11 count 4
# ethtool --set-module swp11s0 power-mode-policy auto
$ ethtool --show-module swp11s0
Module parameters for swp11s0:
power-mode-policy auto
power-mode low
# ip link set dev swp11s0 up
# ip link set dev swp11s1 up
$ ethtool --show-module swp11s0
Module parameters for swp11s0:
power-mode-policy auto
power-mode high
# ip link set dev swp11s1 down
$ ethtool --show-module swp11s0
Module parameters for swp11s0:
power-mode-policy auto
power-mode high
# ip link set dev swp11s0 down
$ ethtool --show-module swp11s0
Module parameters for swp11s0:
power-mode-policy auto
power-mode low
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
