summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2021-10-20net: hns3: Add configuration of TM QCN error eventJiaran Zhang
Add configuration of interrupt type and fifo interrupt enable of TM QCN error event if enabled, otherwise this event will not be reported when there is error. Fixes: d914971df022 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()") Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: dsa: sja1105: parse {rx, tx}-internal-delay-ps properties for RGMII delaysVladimir Oltean
This change does not fix any functional issue or address any real life use case that wasn't possible before. It is just a small step in the process of standardizing the way in which Ethernet MAC drivers may apply RGMII delays (traditionally these have been applied by PHYs, with no clear definition of what to do in the case of a fixed-link). The sja1105 driver used to apply MAC-level RGMII delays on the RX data lines when in fixed-link mode and using a phy-mode of "rgmii-rxid" or "rgmii-id" and on the TX data lines when using "rgmii-txid" or "rgmii-id". But the standard definitions don't say anything about behaving differently when the port is in fixed-link vs when it isn't, and the new device tree bindings are about having a way of applying the delays in a way that is independent of the phy-mode and of the fixed-link property. When the {rx,tx}-internal-delay-ps properties are present, use them, otherwise fall back to the old behavior and warn. One other thing to note is that the SJA1105 hardware applies a delay value in degrees rather than in picoseconds (the delay in ps changes depending on the frequency of the RGMII clock - 125 MHz at 1G, 25 MHz at 100M, 2.5MHz at 10M). I assume that is fine, we calculate the phase shift of the internal delay lines assuming that the device tree meant gigabit, and we let the hardware scale those according to the link speed. Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210723173108.459770-6-prasanna.vengateshan@microchip.com/ Link: https://patchwork.ozlabs.org/project/netdev/patch/20200616074955.GA9092@laureti-dev/#2461123 Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20vrf: Revert "Reset skb conntrack connection..."Eugene Crosser
This reverts commit 09e856d54bda5f288ef8437a90ab2b9b3eab83d1. When an interface is enslaved in a VRF, prerouting conntrack hook is called twice: once in the context of the original input interface, and once in the context of the VRF interface. If no special precausions are taken, this leads to creation of two conntrack entries instead of one, and breaks SNAT. Commit above was intended to avoid creation of extra conntrack entries when input interface is enslaved in a VRF. It did so by resetting conntrack related data associated with the skb when it enters VRF context. However it breaks netfilter operation. Imagine a use case when conntrack zone must be assigned based on the original input interface, rather than VRF interface (that would make original interfaces indistinguishable). One could create netfilter rules similar to these: chain rawprerouting { type filter hook prerouting priority raw; iif realiface1 ct zone set 1 return iif realiface2 ct zone set 2 return } This works before the mentioned commit, but not after: zone assignment is "forgotten", and any subsequent NAT or filtering that is dependent on the conntrack zone does not work. Here is a reproducer script that demonstrates the difference in behaviour. ========== #!/bin/sh # This script demonstrates unexpected change of nftables behaviour # caused by commit 09e856d54bda5f28 ""vrf: Reset skb conntrack # connection on VRF rcv" # https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1 # # Before the commit, it was possible to assign conntrack zone to a # packet (or mark it for `notracking`) in the prerouting chanin, raw # priority, based on the `iif` (interface from which the packet # arrived). # After the change, # if the interface is enslaved in a VRF, such # assignment is lost. Instead, assignment based on the `iif` matching # the VRF master interface is honored. Thus it is impossible to # distinguish packets based on the original interface. # # This script demonstrates this change of behaviour: conntrack zone 1 # or 2 is assigned depending on the match with the original interface # or the vrf master interface. It can be observed that conntrack entry # appears in different zone in the kernel versions before and after # the commit. IPIN=172.30.30.1 IPOUT=172.30.30.2 PFXL=30 ip li sh vein >/dev/null 2>&1 && ip li del vein ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf nft list table testct >/dev/null 2>&1 && nft delete table testct ip li add vein type veth peer veout ip li add tvrf type vrf table 9876 ip li set veout master tvrf ip li set vein up ip li set veout up ip li set tvrf up /sbin/sysctl -w net.ipv4.conf.veout.accept_local=1 /sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0 ip addr add $IPIN/$PFXL dev vein ip addr add $IPOUT/$PFXL dev veout nft -f - <<__END__ table testct { chain rawpre { type filter hook prerouting priority raw; iif { veout, tvrf } meta nftrace set 1 iif veout ct zone set 1 return iif tvrf ct zone set 2 return notrack } chain rawout { type filter hook output priority raw; notrack } } __END__ uname -rv conntrack -F ping -W 1 -c 1 -I vein $IPOUT conntrack -L Signed-off-by: Eugene Crosser <crosser@average.org> Acked-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20zd1201: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-16-kuba@kernel.org
2021-10-20wl3501_cs: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-15-kuba@kernel.org
2021-10-20ray_cs: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-14-kuba@kernel.org
2021-10-20wilc1000: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-13-kuba@kernel.org
2021-10-20hostap: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-11-kuba@kernel.org
2021-10-20ipw2200: prepare for const netdev->dev_addrJakub Kicinski
netdev->dev_addr will be come const soon, constify the argument to command send to avoid compiler warnings. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-10-kuba@kernel.org
2021-10-20airo: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Use dev_addr_set() to match the existing logic. setup_card() is always passed netdev->dev_addr, so pass the netdev pointer instead and assign the address using a helper there. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-9-kuba@kernel.org
2021-10-20brcmfmac: prepare for const netdev->dev_addrJakub Kicinski
netdev->dev_addr will become const soon. Make sure local variables maintain that qualifier. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-8-kuba@kernel.org
2021-10-20atmel: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Use a buffer on the stack. Note that atmel_get_mib() is a wrapper around atmel_copy_to_host(). For the to device direction we just need to make sure functions respect argument being cost. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-7-kuba@kernel.org
2021-10-20wil6210: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Do the special encoding on the stack, then copy the address. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-6-kuba@kernel.org
2021-10-20ath6kl: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Do the special encoding on the stack, then copy the address. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-5-kuba@kernel.org
2021-10-20wireless: use eth_hw_addr_set() for dev->addr_len casesJakub Kicinski
Convert all WiFi drivers from memcpy(... dev->addr_len) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, dev->addr_len) + eth_hw_addr_set(dev, np) Manually checked the netdevs are allocated with alloc_etherdev(), so dev->addr_len must be equal to ETH_ALEN. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-4-kuba@kernel.org
2021-10-20wireless: use eth_hw_addr_set() instead of ether_addr_copy()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Convert wireless from ether_addr_copy() to eth_hw_addr_set(): @@ expression dev, np; @@ - ether_addr_copy(dev->dev_addr, np) + eth_hw_addr_set(dev, np) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-3-kuba@kernel.org
2021-10-20wireless: use eth_hw_addr_set()Jakub Kicinski
Convert all WiFi drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, ETH_ALEN) + eth_hw_addr_set(dev, np) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-2-kuba@kernel.org
2021-10-20iwlwifi: cfg: set low-latency-xtal for some integrated So devicesJohannes Berg
The integrated So devices covered by the iwl_so_long_latency_trans_cfg configuration should all have low-latency-xtal enabled, so do that. While at it, remove the TODO, I've checked the other values as well. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: 6f60fb03c8e7 ("iwlwifi: move SnJ and So rules to the new tables") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.8b5480113f53.I80b5b4ebea84e56f3b3143fc1ee7097be8b4ae78@changeid
2021-10-20iwlwifi: pnvm: read EFI data only if long enoughJohannes Berg
If the data we get from EFI is not even long enough for the package struct we expect then ignore it entirely. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: a1a6a4cf49ec ("iwlwifi: pnvm: implement reading PNVM from UEFI") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.33feba783518.I54a5cf33975d0330792b3d208b225d479e168f32@changeid
2021-10-20iwlwifi: pnvm: don't kmemdup() more than we haveJohannes Berg
We shouldn't kmemdup() more data than we have, that might cause the code to crash. Fix that by updating the length before the kmemdup. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.ab0e64c3fba9.Ic6a3295fc384750b51b4270bf0b7d94984a139f2@changeid
2021-10-20iwlwifi: change all JnP to NO-160 configurationYaara Baruch
JnP should not have the 160 MHz. Signed-off-by: Yaara Baruch <yaara.baruch@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.ee163f4a7513.I7f87bd969a0b038c7f3a1a962d9695ffd18c5da1@changeid
2021-10-20iwlwifi: mvm: reset PM state on unsuccessful resumeJohannes Berg
If resume fails for some reason, we need to set the PM state back to normal so we're able to send commands during firmware reset, rather than failing all of them because we're in D3. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: 708a39aaca22 ("iwlwifi: mvm: don't send commands during suspend\resume transition") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.7ceb9eaca9f6.If0cbef38c6d07ec1ddce125878a4bdadcb35d2c9@changeid
2021-10-20Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo
ath.git patches for v5.16. Major changes: ath9k * add option to reset the wifi chip via debugfs * convert Device Tree bindings to the json-schema * support Device Tree ieee80211-freq-limit property to limit channels
2021-10-20mwifiex: Deactive host sleep using HSCFG after it was activated manuallyJonas Dreßler
When powersaving (so either wifi powersaving or deep sleep, depending on which state the firmware is in) is disabled, the way the firmware goes into host sleep is different: Usually the firmware implicitely enters host sleep on the next SLEEP event we get when we configured host sleep via HSCFG before. When powersaving is disabled though, there are no SLEEP events, the way we enter host sleep in that case is different: The firmware will send us a HS_ACT_REQ event and after that we "manually" make the firmware enter host sleep by sending it another HSCFG command with the action HS_ACTIVATE. Now waking up from host sleep appears to be different depending on whether powersaving is enabled again: When powersaving is enabled, the firmware implicitely leaves host sleep as soon as it wakes up and sends us an AWAKE event. When powersaving is disabled though, it apparently doesn't implicitely leave host sleep, but instead we need to send it a HSCFG command with the HS_CONFIGURE action and the HS_CFG_CANCEL condition. We didn't do that so far, which is why waking up from host sleep was broken when powersaving is disabled. So add some additional state to mwifiex_adapter where we keep track of whether host sleep was activated manually via HS_ACTIVATE, and if that was the case, deactivate it manually again via HS_CFG_CANCEL. Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211016153244.24353-6-verdre@v0yd.nl
2021-10-20mwifiex: Send DELBA requests according to specJonas Dreßler
While looking at on-air packets using Wireshark, I noticed we're never setting the initiator bit when sending DELBA requests to the AP: While we set the bit on our del_ba_param_set bitmask, we forget to actually copy that bitmask over to the command struct, which means we never actually set the initiator bit. Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command struct. Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Acked-by: Pali Rohár <pali@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
2021-10-20mwifiex: Fix an incorrect commentJonas Dreßler
We're sending DELBA requests here, not ADDBA requests. Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211016153244.24353-4-verdre@v0yd.nl
2021-10-20mwifiex: Log an error on command failure during key-material uploadJonas Dreßler
Sometimes the KEY_MATERIAL command can fail with the 88W8897 firmware (when this happens exactly seems pretty random). This appears to prevent the access point from starting, so it seems like a good idea to log an error in that case. Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211016153244.24353-3-verdre@v0yd.nl
2021-10-20mwifiex: Don't log error on suspend if wake-on-wlan is disabledJonas Dreßler
It's not an error if someone chooses to put their computer to sleep, not wanting it to wake up because the person next door has just discovered what a magic packet is. So change the loglevel of this annoying message from ERROR to INFO. Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211016153244.24353-2-verdre@v0yd.nl
2021-10-20rtw89: remove unneeded semicolonYang Li
Eliminate the following coccicheck warning: ./drivers/net/wireless/realtek/rtw89/pci.c:1348:2-3: Unneeded semicolon Reported-by: Abaci Robot <abaci@linux.alibaba.com> Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver") Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1634630094-1156-1-git-send-email-yang.lee@linux.alibaba.com
2021-10-20rtw89: fix return value check in rtw89_cam_send_sec_key_cmd()Yang Yingliang
Fix the return value check which testing the wrong variable in rtw89_cam_send_sec_key_cmd(). Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018033102.1813058-1-yangyingliang@huawei.com
2021-10-20mwl8k: Fix use-after-free in mwl8k_fw_state_machine()Zheyu Ma
When the driver fails to request the firmware, it calls its error handler. In the error handler, the driver detaches device from driver first before releasing the firmware, which can cause a use-after-free bug. Fix this by releasing firmware first. The following log reveals it: [ 9.007301 ] BUG: KASAN: use-after-free in mwl8k_fw_state_machine+0x320/0xba0 [ 9.010143 ] Workqueue: events request_firmware_work_func [ 9.010830 ] Call Trace: [ 9.010830 ] dump_stack_lvl+0xa8/0xd1 [ 9.010830 ] print_address_description+0x87/0x3b0 [ 9.010830 ] kasan_report+0x172/0x1c0 [ 9.010830 ] ? mutex_unlock+0xd/0x10 [ 9.010830 ] ? mwl8k_fw_state_machine+0x320/0xba0 [ 9.010830 ] ? mwl8k_fw_state_machine+0x320/0xba0 [ 9.010830 ] __asan_report_load8_noabort+0x14/0x20 [ 9.010830 ] mwl8k_fw_state_machine+0x320/0xba0 [ 9.010830 ] ? mwl8k_load_firmware+0x5f0/0x5f0 [ 9.010830 ] request_firmware_work_func+0x172/0x250 [ 9.010830 ] ? read_lock_is_recursive+0x20/0x20 [ 9.010830 ] ? process_one_work+0x7a1/0x1100 [ 9.010830 ] ? request_firmware_nowait+0x460/0x460 [ 9.010830 ] ? __this_cpu_preempt_check+0x13/0x20 [ 9.010830 ] process_one_work+0x9bb/0x1100 Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1634356979-6211-1-git-send-email-zheyuma97@gmail.com
2021-10-20rsi: stop thread firstly in rsi_91x_init() error handlingZiyang Xuan
When fail to init coex module, free 'common' and 'adapter' directly, but common->tx_thread which will access 'common' and 'adapter' is running at the same time. That will trigger the UAF bug. ================================================================== BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x] Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777 CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19 Call Trace: dump_stack_lvl+0xe2/0x152 print_address_description.constprop.0+0x21/0x140 ? rsi_tx_scheduler_thread+0x50f/0x520 kasan_report.cold+0x7f/0x11b ? rsi_tx_scheduler_thread+0x50f/0x520 rsi_tx_scheduler_thread+0x50f/0x520 ... Freed by task 111873: kasan_save_stack+0x1b/0x40 kasan_set_track+0x1c/0x30 kasan_set_free_info+0x20/0x30 __kasan_slab_free+0x109/0x140 kfree+0x117/0x4c0 rsi_91x_init+0x741/0x8a0 [rsi_91x] rsi_probe+0x9f/0x1750 [rsi_usb] Stop thread before free 'common' and 'adapter' to fix it. Fixes: 2108df3c4b18 ("rsi: add coex support") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com
2021-10-20mt76: mt7915: change max rx len limit of hw modulesShayne Chen
Update max rx len of some hw modules, which aligns out vendor SDK. In normal modes, we exchange MPDU 7991 cap with peers; however, this won't play a part in sniffer mode. To prevent packets which exceed the max MPDU size from entering specific rx path in hw, we need to set a proper limit to filter them out. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7915: fix missing HE phy capShayne Chen
Fix missing HE phy cap related to vif and starec setting. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7915: rework mt7915_mcu_sta_muru_tlv()Shayne Chen
Re-order and modify conditions for MU DL/UL and ofdma DL fields, and also clean up some unnecessary zero settings. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7915: enable HE UL MU-MIMOShayne Chen
Enable HE UL MU-MIMO in sta_rec_muru, which works on both ap and station mode. For sending trigger frames, one of the conditions fw uses is to check if mib rx airtime meets the threshold. There's a main control of mib rx airtime report register in fw, so we need to enable the register by mcu cmd instead of directly writing it, otherwise it will still be disabled by fw. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7921: add per-vif counters in ethtoolLorenzo Bianconi
Similar to mt7915 driver, add per-vif tx counters in ethtool. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7921: move tx amsdu stats in mib_statsLorenzo Bianconi
Move tx_amsdu histogram stats in mib_stats structure since registers are clear-on-read Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7921: add sta stats accounting in mt7921_mac_add_txs_skbLorenzo Bianconi
This is a preliminary patch to add ethtool stats to mt7921 driver. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7921: introduce stats reporting through ethtoolLorenzo Bianconi
Similar to mt7915 driver, add tx/rx statistics reporting through ethtool. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7921: add some more MIB countersLorenzo Bianconi
This is a preliminary patch to introduce ethtool stats support to mt7921 driver. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: do not reset MIB counters in get_stats callbackLorenzo Bianconi
MIB counters are used for ethtool stats as well Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7915: move tx amsdu stats in mib_statsLorenzo Bianconi
Move tx_amsdu histogram stats in mib_stats structure since registers are clear-on-read Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7915: run mt7915_get_et_stats holding mt76 mutexLorenzo Bianconi
Since it can run in parallel with mac_work, hold mutex lock in mt7915_get_et_stats. Moreover update mib counters running mt7915_get_et_stats. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: move mt76_ethtool_worker_info in mt76 moduleLorenzo Bianconi
Move mt76_ethtool_worker_info in common code in order to be reused in mt7921 driver. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: move mt76_sta_stats in mt76.hLorenzo Bianconi
This is a preliminary patch to add ethtool stats to mt7921 driver. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt76x0: correct VHT MCS 8/9 tx power eeprom offsetRichard Huynh
Appears to have incorrectly offset 0x120 + 0x12 instead of 12 decimal, leading to bogus power values being used. Signed-off-by: Richard Huynh <voxlympha@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7921s: add reset supportSean Wang
Introduce wifi chip reset support for mt7921 device to recover mcu hangs or abnormal wifi system. Tested-by: Deren Wu <deren.wu@mediatek.com> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Co-developed-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7921: introduce mt7921s supportSean Wang
Introduce support for mt7921s 802.11ax (Wi-Fi 6) 2x2:2SS chipset. Tested-by: Deren Wu <deren.wu@mediatek.com> Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-10-20mt76: mt7921: refactor mt7921_mcu_send_messageSean Wang
This is a preliminary patch to introduce mt7921s support. Refactor mt7921_mcu_send_message to be sharable between mt7921s and mt7921e. Tested-by: Deren Wu <deren.wu@mediatek.com> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit (git 2.34.1) at 2025-09-12 13:30:22 +0000