summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2017-04-05bnxt_en: Add ethtool get_wol method.Michael Chan
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-05bnxt_en: Add pci shutdown method.Michael Chan
Add pci shutdown method to put device in the proper WoL and power state. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-05bnxt_en: Add basic WoL infrastructure.Michael Chan
Add code to driver probe function to check if the device is WoL capable and if Magic packet WoL filter is currently set. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-05bnxt_en: Update firmware interface spec to 1.7.6.2.Michael Chan
Features added include WoL and selftest. Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-05mwifiex: apply radar flagKarthik Ananthapadmanabha
When IEEE80211_CHAN_RADAR is set by cfg80211, passive scan must be performed. In mwifiex,active scan is performed even though flag is set from cfg80211. mwifiex_reg_apply_radar_flags() function added in this patch correctly uses radar flag. Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: new fw use h2c to control GNT_BTYan-Hsuan Chuang
Earlier versions of the FW did not support h2c to set GNT_BT, but later versions have that capability. Hence we check the FW version and decide whether to use h2c or just write to the register. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: add comments to describe how duration adjustedYan-Hsuan Chuang
Since btcoex uses static variables to store the cumulative information on the wifi status, some tricks are used that are a bit obscure. We add some comments about the criteria we use to adjust wifi duration. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: finer bt power adjustmentYan-Hsuan Chuang
The bt can specify a power level to decrease. Rather than decreasing by a fixed value (usually 2), this change makes the driver fit to the environment more quickly. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: remove redundant bt stack reportYan-Hsuan Chuang
New ICs have hardware mailbox to deliver bt information instead of doing it by driver itself, so remove them. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: coex table fine tuneYan-Hsuan Chuang
set coex table fine tune, for register settings Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: adjust wifi duration for bt a2dpYan-Hsuan Chuang
The larger the bt a2dp bit pool is, the more time bt needs to receive them. If we do not adjust the wifi duration, the voice quality will be low. Hence we reduce the time that wifi holds, to improve the a2dp service. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: less sensitive to tx rate penaltyYan-Hsuan Chuang
modify h2c parameter so that the rate suffers less penalty from retry Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: monitor wifi counter for allocate tdma timeYan-Hsuan Chuang
If there are too many CRC error packets, it means the wifi is operating under low quality circumstances. If so, we need to reallocate the resources of wifi and bt Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: detect if bt is slave, and modify tdmaYan-Hsuan Chuang
if the bt is slave, it may receive packet at any time, so we need to mark them as high priority packets to avoid packet loss. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: 23b 2ant: add btc8723b2ant_limited_rx to reduce agg sizeYan-Hsuan Chuang
For wifi and bt coexistence, if the aggregation size of wifi is too large, the transmission time of the aggregated packet could be too long and the bt packets might "cut off" the wifi packet. We need to reduce the aggregation size to improve wifi performance. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: follow linux coding styleYan-Hsuan Chuang
Fix a number of checkpatch.pl warnings. In addition, some variable and function names are shortened, and/or renamed to be more consistent. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05rtlwifi: btcoex: remove unused functionsYan-Hsuan Chuang
A number of functions in the Bluetooth Coexistence routines are not used, and can be removed. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05mwifiex: add missing IEs related to TDLS operationKarthik Ananthapadmanabha
In mwifiex,IEs such as supported channels, supported operating classes 20/40 BSS COexistence are missing and also extra QOS capabilities IE is added during TDLS discovery response, TDLS setup request and TDLS setupresponse. This patch adds require IEs and also removes extra IE. Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com> Signed-off-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05wlcore: fix spelling mistakes in wl1271_warningColin Ian King
trivial fix to spelling mistakes in wl1271_warning error message, change iligal to invalid and opperation to operation. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05mwifiex: catch mwifiex_fw_dpc() errors properly in resetBrian Norris
When resetting the device, we take a synchronous firmware-loading code path, which borrows a lot from the asynchronous path used at probe time. We don't catch errors correctly though, which means that in the PCIe driver, we may try to dereference the 'adapter' struct after mwifiex_fw_dpc() has freed it. See this (erronous) print in mwifiex_pcie_reset_notify(): mwifiex_dbg(adapter, INFO, "%s, successful\n", __func__); Let's instead refactor the synchronous (or "!req_fw_nowait") path so that we propagate errors and handle them properly. This fixes a use-after-free issue in the PCIe driver, as well as a misleading debug message ("successful"). It looks like the SDIO driver doesn't have these problems, since it doesn't do anything after mwifiex_reinit_sw(). Fixes: 4c5dae59d2e9 ("mwifiex: add PCIe function level reset support") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05mwifiex: fix use-after-free for FW reinit errorsBrian Norris
If we fail to reinit the FW when resetting the device (in the synchronous version of mwifiex_init_hw_fw() -> mwifiex_fw_dpc()), mwifiex_fw_dpc() will tear down the interface and free up the adapter. But we don't actually check for all failure cases of mwifiex_fw_dpc(), so some of them fall through and dereference adapter->fw_done with a freed adapter, causing a use-after-free bug. In any case, mwifiex_fw_dpc() will always signal FW completion -- in the error OR success case -- so at best, this was repeat work. Let's not do it. Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05brcmfmac: no need for d11inf instance in brcmf_pno_start_sched_scan()Arend Van Spriel
In brcmf_pno_start_sched_scan() a local variable is declared and assigned for struct brcmu_d11inf. However, there is no other reference to it so it is unnecessary. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05brcmfmac: restore bus state when enter_D3 failsArend Van Spriel
In brcmf_pcie_suspend() we inform the firmware on the device that it will enter in D3 state. Before this is done we already bring down the bus state. However, When entering D3 fails we abort the suspend and the bus state need to be restored. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05brcmfmac: add support to move wiphy instance into network namespaceArend Van Spriel
To support network namespace the driver must assure all created network interfaces are in the same namespace as the wiphy instance and flag the support using WIPHY_FLAG_NETNS_OK. Verified using two terminals: Terminal 1 Terminal 2 -------------------------- --------------------------------- # ip netns add brcm-wifi # iw dev phy#0 Interface wlan3 ifindex 11 wdev 0x1 # ip netns exec brcm-wifi bash # iw dev # echo $$ 20337 # iw phy0 set netns 20337 # iw dev phy#0 Interface wlan3 ifindex 11 wdev 0x2 # iw phy0 interface add wl3.ap type __ap # iw dev phy#0 Interface wl3.ap ifindex 2 wdev 0x3 Interface wlan3 ifindex 11 wdev 0x2 # iw dev # iw phy0 set netns 1 # iw dev # iw dev phy#0 Interface wl3.ap ifindex 2 wdev 0x5 Interface wlan3 ifindex 11 wdev 0x4 Note: increasing wdev identifier above indicates issue in cfg80211 which is addressed separately. Tested-by: Mark Asselstine <mark.asselstine@windriver.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05brcmfmac: move brcmf_fws_deinit to bcdc layerFranky Lin
Move brcmf_fws_deinit into brcmf_proto_bcdc_detach since it is a bcdc exclusive feature. Signed-off-by: Franky Lin <franky.lin@broadcom.com> Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05brcmfmac: wrap brcmf_fws_init into bcdc layerFranky Lin
Create a new protocol layer interface brcmf_proto_init_cb for protocol layer to finish initialzation after core module components(fweh and etc.) are initialized. Signed-off-by: Franky Lin <franky.lin@broadcom.com> Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05mwifiex: enable auto deep sleep mode for USB chipsetsAmitkumar Karwar
Chip goes into low power state when this feature is enabled. This was already enabled for SDIO and PCIe interface based chipsets. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05mwifiex: Support USB interrupt endpoint for command response/eventGanapathi Bhat
USB firmware added support for sending command response/event through interrupt endpoint, to enhance RX throughput. Added corresponding changes required to support this feature. This change takes care of backward compatibility with older firmware. Signed-off-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05brcmfmac: update BRCMFMAC symbol descriptionRafał Miłecki
For quite some time now brcmfmac supports 802.11ac chipsets and it's not limited to embedded devices only. There are even standalone PCIe cards based on BCM43602 or BCM4366. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-05ath10k: clean header files from bad block commentsMarcin Rokicki
Fix output from checkpatch.pl like: Block comments use a trailing */ on a separate line Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath10k: use octal permission representationMarcin Rokicki
Fix output from checkpatch.pl like: Symbolic permissions 'S_IRUSR' are not preferred. Consider using octal permissions '0400'. Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath10k: fix block comments styleMarcin Rokicki
Fix output from checkpatch.pl like: Block comments use a trailing */ on a separate lin Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath10k: fix the Transmit Power Control stats display formatMaharaja Kennadyrajan
This patch helps to fix TPC stats to display the stats properly. Here cosmetic change has been done to print the TPC stats for all the cases 1.CDD 2.STBC 3.TXBF Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath10k: remove obselete Copy Engine commentsMohammed Shafi Shajakhan
Remove obselete Copy Engine comments referring to the function ath10k_ce_sendlist_send as this function was removed long time back by the commit 2e761b5a5222 ("ath10k: remove ce_sendlist_send"). Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath10k: enable a HTC debug message during insufficient tx creditsMohammed Shafi Shajakhan
Add an ath10k HTC debug message when insufficient tx credits are available to send the WMI commands. This is very useful in debugging issues like 'tx credit starvation' that could possibly happen with multiclient setup with constant roaming Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath10k: cancel coverage class work during stop and restartMohammed Shafi Shajakhan
It seems set_coverage_class_work is not cancelled anywhere, though I could not find a crash/warning with this existing design, its safer to cancel it during stop() and also before restarting the hardware. Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath10k: fix station nss computationVenkateswara Rao Naralasetty
If station advertises diffferent NSS capabilities in Rx_mcs set of HT and VHT IEs in assoc req, the current NSS computation logic configures the NSS support only based on Rx_mcs set of HT capabilities in the driver. This is configuring the station NSS capabilities incorreclty in the target. For example, if station advertise Rx_mcs set as 2 spatial streams in HT capabilities and 1 spatial streams in VHT capabilities in assoc request, as per current logic we are calculating nss from HT capabilities and the driver sets peer_num_spatial_streams as 2 for the station which is configured in VHT 1*1. This patchs fix this issue by calculating the nss from VHT cap if station supports vht. Signed-off-by: Venkateswara Rao Naralasetty <c_vnaral@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath9k_htc: fix NULL-deref at probeJohan Hovold
Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Fixes: 36bcce430657 ("ath9k_htc: Handle storage devices") Cc: stable <stable@vger.kernel.org> # 2.6.39+ Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05ath10k: fix NAPI enable/disable symmetry for AHB interfaceMohammed Shafi Shajakhan
Move NAPI enable to 'ath10k_ahb_hif_start' from 'ath10k_ahb_hif_power_up'. This is to maintain the symmetry of calling napi_enable() from ath10k_ahb_hif_start() so that it matches with napi_disable() being called from ath10k_pci_hif_stop(). This change is based on the crash fix from Kalle for PCI interface in commit 1427228d5869 ("ath10k: fix napi crash during rmmod when probe firmware fails"). Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-05Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo
ath.git patches for 4.12. Major changes: ath10k * improve firmware download time for QCA6174 and QCA9377, especially helps resume time ath9k_htc * add support AirTies 1eda:2315 AR9271 device
2017-04-04Merge tag 'wireless-drivers-for-davem-2017-04-03' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 4.11 iwlwifi * an RCU fix * a fix for a potential out-of-bounds access crash * a fix for IBSS which has been broken since DQA was enabled rtlwifi * fix scheduling while atomic regression brcmfmac * fix use-after-free bug found by KASAN ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-04net: ethernet: ti: cpsw: fix race condition during open()Sekhar Nori
TI's cpsw driver handles both OF and non-OF case for phy connect. Unfortunately of_phy_connect() returns NULL on error while phy_connect() returns ERR_PTR(). To handle this, cpsw_slave_open() overrides the return value from phy_connect() to make it NULL or error. This leaves a small window, where cpsw_adjust_link() may be invoked for a slave while slave->phy pointer is temporarily set to -ENODEV (or some other error) before it is finally set to NULL. _cpsw_adjust_link() only handles the NULL case, and an oops results when ERR_PTR() is seen by it. Note that cpsw_adjust_link() checks PHY status for each slave whenever it is invoked. It can so happen that even though phy_connect() for a given slave returns error, _cpsw_adjust_link() is still called for that slave because the link status of another slave changed. Fix this by using a temporary pointer to store return value of {of_}phy_connect() and do a one-time write to slave->phy. Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reported-by: Yan Liu <yan-liu@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-04Merge tag 'wireless-drivers-for-davem-2017-04-03' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 4.11 iwlwifi * an RCU fix * a fix for a potential out-of-bounds access crash * a fix for IBSS which has been broken since DQA was enabled rtlwifi * fix scheduling while atomic regression brcmfmac * fix use-after-free bug found by KASAN ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-04bnx2x: fix spelling mistake in macros HW_INTERRUT_ASSERT_SET_*Colin Ian King
Trival fix, rename HW_INTERRUT_ASSERT_SET_* to HW_INTERRUPT_ASSERT_SET_* Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-04can: rcar_can: Do not print virtual addressesGeert Uytterhoeven
During probe, the rcar_can driver prints: rcar_can e6e80000.can: device registered (regs @ e08bc000, IRQ76) The "regs" value is a virtual address, exposing internal information, hence stop printing it. The (useful) physical address is already printed as part of the device name. Fixes: fd1159318e55e901 ("can: add Renesas R-Car CAN driver") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2017-04-04can: ifi: use correct register to read rx statusMarkus Marb
The incorrect offset was used when trying to read the RXSTCMD register. Signed-off-by: Markus Marb <markus@marb.org> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2017-04-04can: hi311x: Add Holt HI-311x CAN driverAkshay Bhat
This patch adds support for the Holt HI-311x CAN controller. The HI311x CAN controller is capable of transmitting and receiving standard data frames, extended data frames and remote frames. The HI311x interfaces with the host over SPI. Datasheet: www.holtic.com/documents/371-hi-3110_v-rev-jpdf.do Signed-off-by: Akshay Bhat <nodeax@gmail.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2017-04-04can: ti_hecc: Convert TI HECC driver to DT only driverYegor Yefremov
This patch converts TI HECC driver to DT only driver. This results in removing ti_hecc.h containing now obsolete platform data. Former transceiver_switch callback function will be now modelled via regulator API. Signed-off-by: Anton Glukhov <anton.a.glukhov@gmail.com> Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2017-04-03qed: Manage with less memory regions for RoCERam Amrani
It's possible some configurations would prevent driver from utilizing all the Memory Regions due to a lack of ILT lines. In such a case, calculate how many memory regions would have to be dropped due to limit, and manage without those. Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-03qed: RoCE doesn't need to use SRCMintz, Yuval
As RoCE doesn't need to use the SRC, allocating ILT memory on behalf of RoCE is wasting available ILT lines. Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-09-16 04:29:38 +0000