| Age | Commit message (Collapse) | Author |
|---|
|
Frame size ENA_PAGE_SIZE is limited to 16K on systems with larger
PAGE_SIZE than 16K. Change ENA_XDP_MAX_MTU to also take into account
the reserved tailroom.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Cc: Arthur Kiyanovski <akiyano@amazon.com>
Link: https://lore.kernel.org/bpf/158945341384.97035.907403694833419456.stgit@firesoul
|
|
The driver code cpsw.c and cpsw_new.c both use page_pool
with default order-0 pages or their RX-pages.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/bpf/158945340875.97035.752144756428532878.stgit@firesoul
|
|
The driver qede uses a full page, when XDP is enabled. The drivers value
in rx_buf_seg_size (struct qede_rx_queue) will be PAGE_SIZE when an
XDP bpf_prog is attached.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Ariel Elior <aelior@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Link: https://lore.kernel.org/bpf/158945340366.97035.7764939691580349618.stgit@firesoul
|
|
The hyperv NIC driver does memory allocation and copy even without XDP.
In XDP mode it will allocate a new page for each packet and copy over
the payload, before invoking the XDP BPF-prog.
The positive thing it that its easy to determine the xdp.frame_sz.
The XDP implementation for hv_netvsc transparently passes xdp_prog
to the associated VF NIC. Many of the Azure VMs are using SRIOV, so
majority of the data are actually processed directly on the VF driver's XDP
path. So the overhead of the synthetic data path (hv_netvsc) is minimal.
Then XDP is enabled on this driver, XDP_PASS and XDP_TX will create the
SKB via build_skb (based on the newly allocated page). Now using XDP
frame_sz this will provide more skb_tailroom, which netstack can use for
SKB coalescing (e.g tcp_try_coalesce -> skb_try_coalesce).
V3: Adjust patch desc to be more positive.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Link: https://lore.kernel.org/bpf/158945339857.97035.10212138582505736163.stgit@firesoul
|
|
The dpaa2-eth driver reserve some headroom used for hardware and
software annotation area in RX/TX buffers. Thus, xdp.data_hard_start
doesn't start at page boundary.
When XDP is configured the area reserved via dpaa2_fd_get_offset(fd) is
448 bytes of which XDP have reserved 256 bytes. As frame_sz is
calculated as an offset from xdp_buff.data_hard_start, an adjust from
the full PAGE_SIZE == DPAA2_ETH_RX_BUF_RAW_SIZE.
When doing XDP_REDIRECT, the driver doesn't need this reserved headroom
any-longer and allows xdp_do_redirect() to use it. This is an advantage
for the drivers own ndo-xdp_xmit, as it uses part of this headroom for
itself. Patch also adjust frame_sz in this case.
The driver cannot support XDP data_meta, because it uses the headroom
just before xdp.data for struct dpaa2_eth_swa (DPAA2_ETH_SWA_SIZE=64),
when transmitting the packet. When transmitting a xdp_frame in
dpaa2_eth_xdp_xmit_frame (call via ndo_xdp_xmit) is uses this area to
store a pointer to xdp_frame and dma_size, which is used in TX
completion (free_tx_fd) to return frame via xdp_return_frame().
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Link: https://lore.kernel.org/bpf/158945339348.97035.8562488847066908856.stgit@firesoul
|
|
The veth driver can run XDP in "native" mode in it's own NAPI
handler, and since commit 9fc8d518d9d5 ("veth: Handle xdp_frames in
xdp napi ring") packets can come in two forms either xdp_frame or
skb, calling respectively veth_xdp_rcv_one() or veth_xdp_rcv_skb().
For packets to arrive in xdp_frame format, they will have been
redirected from an XDP native driver. In case of XDP_PASS or no
XDP-prog attached, the veth driver will allocate and create an SKB.
The current code in veth_xdp_rcv_one() xdp_frame case, had to guess
the frame truesize of the incoming xdp_frame, when using
veth_build_skb(). With xdp_frame->frame_sz this is not longer
necessary.
Calculating the frame_sz in veth_xdp_rcv_skb() skb case, is done
similar to the XDP-generic handling code in net/core/dev.c.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Link: https://lore.kernel.org/bpf/158945338840.97035.935897116345700902.stgit@firesoul
|
|
When native XDP redirect into a veth device, the frame arrives in the
xdp_frame structure. It is then processed in veth_xdp_rcv_one(),
which can run a new XDP bpf_prog on the packet. Doing so requires
converting xdp_frame to xdp_buff, but the tricky part is that
xdp_frame memory area is located in the top (data_hard_start) memory
area that xdp_buff will point into.
The current code tried to protect the xdp_frame area, by assigning
xdp_buff.data_hard_start past this memory. This results in 32 bytes
less headroom to expand into via BPF-helper bpf_xdp_adjust_head().
This protect step is actually not needed, because BPF-helper
bpf_xdp_adjust_head() already reserve this area, and don't allow
BPF-prog to expand into it. Thus, it is safe to point data_hard_start
directly at xdp_frame memory area.
Fixes: 9fc8d518d9d5 ("veth: Handle xdp_frames in xdp napi ring")
Reported-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/158945338331.97035.5923525383710752178.stgit@firesoul
|
|
This driver takes advantage of page_pool PP_FLAG_DMA_SYNC_DEV that
can help reduce the number of cache-lines that need to be flushed
when doing DMA sync for_device. Due to xdp_adjust_tail can grow the
area accessible to the by the CPU (can possibly write into), then max
sync length *after* bpf_prog_run_xdp() needs to be taken into account.
For XDP_TX action the driver is smart and does DMA-sync. When growing
tail this is still safe, because page_pool have DMA-mapped the entire
page size.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/bpf/158945336295.97035.15034759661036971024.stgit@firesoul
|
|
This marvell driver mvneta uses PAGE_SIZE frames, which makes it
really easy to convert. Driver updates rxq and now frame_sz
once per NAPI call.
This driver takes advantage of page_pool PP_FLAG_DMA_SYNC_DEV that
can help reduce the number of cache-lines that need to be flushed
when doing DMA sync for_device. Due to xdp_adjust_tail can grow the
area accessible to the by the CPU (can possibly write into), then max
sync length *after* bpf_prog_run_xdp() needs to be taken into account.
For XDP_TX action the driver is smart and does DMA-sync. When growing
tail this is still safe, because page_pool have DMA-mapped the entire
page size.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: thomas.petazzoni@bootlin.com
Link: https://lore.kernel.org/bpf/158945335786.97035.12714388304493736747.stgit@firesoul
|
|
This driver uses RX page-split when possible. It was recently fixed
in commit 86e85bf6981c ("sfc: fix XDP-redirect in this driver") to
add needed tailroom for XDP-redirect.
After the fix efx->rx_page_buf_step is the frame size, with enough
head and tail-room for XDP-redirect.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/158945335278.97035.14611425333184621652.stgit@firesoul
|
|
This driver uses full PAGE_SIZE pages when XDP is enabled.
In case of XDP uses driver uses __bnxt_alloc_rx_page which does full
page DMA-map. Thus, xdp_adjust_tail grow is DMA compliant for XDP_TX
action that does DMA-sync.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Link: https://lore.kernel.org/bpf/158945334769.97035.13437970179897613984.stgit@firesoul
|
|
93882c6f210a ("r8169: switch from netif_xxx message functions to
netdev_xxx") removed the last module parameter from the driver,
therefore there's no need any longer to include linux/moduleparam.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After 9de5d235b60a ("net: phy: fix aneg restart in phy_ethtool_set_eee")
we don't need the check for aneg being enabled any longer, and as
discussed with Russell configuring the EEE advertisement should be
supported even if we're in a half-duplex mode currently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently burst is clamping on rate and not burst, the assignment
of burst from the clamping discards the previous assignment of burst.
This looks like a cut-n-paste error from the previous clamping
calculation on ramp. Fix this by replacing ramp with burst.
Addresses-Coverity: ("Unused value")
Fixes: 0fbabf875d18 ("net: dsa: felix: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mdio-moxart doesn't use regulators in the driver code. We can remove
the regulator include.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the following warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc5-next-20200514-syzkaller #0 Not tainted
-----------------------------
drivers/net/hamradio/bpqether.c:149 RCU-list traversed in non-reader section!!
Since rtnl lock is held, pass this cond in list_for_each_entry_rcu().
Reported-by: syzbot+bb82cafc737c002d11ca@syzkaller.appspotmail.com
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the correct bit when checking for PHY_BRCM_DIS_TXCRXC_NOENRGY on the
BCM54810 PHY.
Fixes: 0ececcfc9267 ("net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk()")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
support to change TX/RX queue depth with ethtool -G
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration. EST allows express queue traffic to be scheduled
(placed) on the wire at specific repeatable time intervals. In
Linux kernel, EST configuration is done through tc command and
the taprio scheduler in the net core implements a software only
scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
user indicate "flag 2" in the command which is then parsed by
taprio scheduler in net core and indicate that the command is to
be offloaded to h/w. taprio then offloads the command to the
driver by calling ndo_setup_tc() ndo ops. This patch implements
ndo_setup_tc() to offload EST configuration to CPSW h/w.
Currently driver supports only SetGateStates operation. EST
operates on a repeating time interval generated by the CPTS EST
function generator. Each Ethernet port has a global EST fetch
RAM that can be configured as 2 buffers, each of 64 locations
or one large buffer of 128 locations. In 2 buffer configuration,
a ping pong mechanism is used to hold the active schedule (oper)
in one buffer and new (admin) command in the other. Each 22-bit
fetch command consists of a 14-bit fetch count (14 MSB’s) and an
8-bit priority fetch allow (8 LSB’s) that will be applied for the
fetch count time in wireside clocks. Driver process each of the
sched-entry in the offload command and update the fetch RAM.
Driver configures duration in sched-entry into the fetch count
and Gate mask into the priority fetch bits of the RAM. Then
configures the CPTS EST function generator to activate the
schedule. Currently driver supports only 2 buffer configuration
which means driver supports a max cycle time of ~8 msec.
CPSW supports a configurable number of priority queues (up to 8)
and needs to be switched to this mode from the default round
robin mode before EST can be offloaded. User configures
these through ethtool commands (-L for changing number of
queues and --set-priv-flags to disable round robin mode).
Driver doesn't enable EST if pf_p0_rx_ptype_rrobin privat flag
is set. The flag is common for all ports, and so can't be just
overridden by taprio configuration w/o user involvement.
Command fails if pf_p0_rx_ptype_rrobin is already set in the
driver.
Scheds (commands) configuration depends on interface speed so
driver translates the duration to the fetch count based on
link speed. Each schedule can be constructed with several
command entries in fetch RAM depending on interval. For example
if each sched has timer interval < ~130us on 1000 Mb link then
each sched consumes one command and have 1:1 mapping. When
Ethernet link goes down, driver purge the configuration if link
is down for more than 1 second.
The patch allows to update the timer and scheds memory only if it's
really needed, and skip cases required the user to stop timer by
configuring only shceds memory.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TAPRIO/EST offload support in CPSW2G requires EST scheduler
function enabled in CPTS. So this patch add a function to
set cycle time for EST scheduler. It also add a function for
getting time in ns of PHC clock for taprio qdisc configuration.
Mostly to verify if timer update is needed or to get actual
state of oper/admin schedule.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MCP may signal driver about generic critical failure.
Driver has to collect mdump information (get_retain),
it pushes that to logs and triggers generic notification on
"hardware attention" event.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fan failure is sent by firmware, driver reacts on this error with
newly introduced notification path. It will collect dump and shut down
the device to prevent physical breakage
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon tx timeout detection we do disable carrier and print TX queue
info on TX timeout. We then raise hw error condition and trigger
service task to handle this.
This handler will capture extra debug info and then optionally
trigger recovery procedure to try restore function.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver has an ability to initiate a recovery process as a reaction to
detected errors. But the codepath (recovery_process) was disabled and
never active.
Here we add ethtool private flag to allow user have the recovery
procedure activated.
We still do not enable this by default though, since in some configurations
this is not desirable. E.g. this may impact other PFs/VFs.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On different hardware events we have to respond differently,
on some of hardware indications hw attention (error condition)
should be cleared by the driver to continue normal functioning.
Here we introduce attention clear flags, and put them on some
important events (in aeu_descs).
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thats probably a legacy code had double declaration of some fields.
Cleanup this, removing copy and fixing references.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On various critical errors, notification handler should also report
the err information into the management firmware.
MFW can interact with server/motherboard backend agents - these are
used by server manufacturers to monitor server HW health.
Thus, it is important for driver to report on any faulty conditions
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a number of critical places not only debug trace should be printed,
but the appropriate hw error condition should be raised and error
handling/recovery should start.
Introduce our new qed_hw_err_notify invocation in these places to
record and indicate critical error conditions in hardware.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qede (ethernet level driver) registers a callback handler.
This handler maintains eth dev state flags/bits to track error processing.
It implements in place processing part for nonsleeping context (WARN_ON
trigger), and a deferred (delayed work) part which triggers recovery
process for recoverable errors.
In later patches this atomic handler will come with more meat.
We introduce err_flags on ethdevice structure, its being used to record
error handling properties.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here we introduce qed device error tracking flags and error types.
qed_hw_err_notify is an entrace point to report errors.
It'll notify higher level drivers (qede/qedr/etc) to handle and recover
the error.
List of posible errors comes from hardware interfaces, but could be
extended in future.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb_has_frag_list() in hns3_nic_net_xmit() is redundant, since
skb_walk_frags() includes this checking implicitly.
Reported-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some macros defined in hns3_enet.h, but not used in
anywhere.
Reported-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When handling HCLGE_MBX_GET_LINK_STATUS, PF will return the link
status to the VF, so the error log of hclge_get_link_info() is
incorrect.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since hclge_get_cfg() already has error print, so hclge_configure()
should not print error when calling hclge_get_cfg() fail.
Reported-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch modifies some incorrect spelling.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a MAC address was passed via the device tree node for the r8152
device, use it and fall back to reading from EEPROM otherwise. This is
useful for devices where the r8152 EEPROM was not programmed with a
valid MAC address, or if users want to explicitly set a MAC address in
the bootloader and pass that to the kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the duplicate "mutex", and change "Motex" to "Mutex". Also I
recommend it's easier for understanding to make the "ready-interrupt"
a bundle for it is a parallel description as "shutdown" which is appended
after the slash.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Cc: Alex Elder <elder@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't want to disconnect a session because of a stray PADT arriving
while the interface is in promiscuous mode.
Furthermore, multicast and broadcast packets make no sense here, so
only PACKET_HOST is accepted.
Reported-by: David Balažic <xerces9@gmail.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver missed initializing num_por which is one of the por values that
driver configures to hardware. In order to get these values, add a new
structure ethqos_emac_driver_data which holds por and num_por values
and populate that in driver probe.
Fixes: a7c30e62d4b8 ("net: stmmac: Add driver for Qualcomm ethqos")
Reported-by: Rahul Ankushrao Kawadgave <rahulak@qti.qualcomm.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix typo defining ps_work in mt7615_register_ext_phy(). This is not a
real issue since 802.11 power save is not yet support by the external phy
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_restart_aneg() enables aneg in the PHY. That's not what we want
if phydev->autoneg is disabled. In this case still update EEE
advertisement register, but don't enable aneg and don't trigger an
aneg restart.
Fixes: f75abeb8338e ("net: phy: restart phy autonegotiation after EEE advertisment change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHYs connected to this ethernet hardware support the WoL feature.
But when WoL is enabled and the machine is powered off, the PHY remains
waiting for a magic packet at max speed (i.e. 1Gbps), which is a waste of
energy.
Slow down the PHY speed before stopping the ethernet if WoL is enabled,
and save some energy while the machine is powered off or sleeping.
Tested using an Armada 370 based board (LS421DE) equipped with a Marvell
88E1518 PHY.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently pointer table is being dereferenced on a null check of
table->must_restore_filters before it is being null checked, leading
to a potential null pointer dereference issue. Fix this by null
checking table before dereferencing it when checking for a null
table->must_restore_filters.
Addresses-Coverity: ("Dereference before null check")
Fixes: e4fe938cff04 ("sfc: move 'must restore' flags out of ef10-specific nic_data")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AR8031/AR8033 and the AR8035 support cable diagnostics. Adding
driver support is straightforward, so lets add it.
The PHY just do one pair at a time, so we have to start the test four
times. The cable_test_get_status() can block and therefore we can just
busy poll the test completion and continue with the next pair until we
are done.
The time delta counter seems to run at 125MHz which just gives us a
resolution of about 82.4cm per tick.
100m cable, A/B/C/D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: Open Circuit
Pair: Pair A, fault length: 107.94m
Pair: Pair B, result: Open Circuit
Pair: Pair B, fault length: 104.64m
Pair: Pair C, result: Open Circuit
Pair: Pair C, fault length: 105.47m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 107.94m
1m cable, A/B connected, C shorted, D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short within Pair
Pair: Pair C, fault length: 0.82m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 0.82m
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the generic cable tester functions from bcm-phy-lib to add cable
tester support.
100m cable, A/B/C/D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: Open Circuit
Pair: Pair B, result: Open Circuit
Pair: Pair C, result: Open Circuit
Pair: Pair D, result: Open Circuit
Pair: Pair A, fault length: 106.60m
Pair: Pair B, fault length: 103.32m
Pair: Pair C, fault length: 104.96m
Pair: Pair D, fault length: 106.60m
1m cable, A/B connected, pair C shorted, D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short within Pair
Pair: Pair D, result: Open Circuit
Pair: Pair C, fault length: 0.82m
Pair: Pair D, fault length: 1.64m
1m cable, A/B connected, pair C shorted with D:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short to another pair
Pair: Pair D, result: Short to another pair
Pair: Pair C, fault length: 1.64m
Pair: Pair D, fault length: 1.64m
The granularity of the length measurement seems to be 82cm.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most modern broadcom PHYs support ECD (enhanced cable diagnostics). Add
support for it in the bcm-phy-lib so they can easily be used in the PHY
driver.
There are two access methods for ECD: legacy by expansion registers and
via the new RDB registers which are exclusive. Provide functions in two
variants where the PHY driver can choose from. To keep things simple for
now, we just switch the register access to expansion registers in the
RDB variant for now. On the flipside, we have to keep a bus lock to
prevent any other non-legacy access on the PHY.
The results of the intra-pair tests are inconclusive (at least for the
BCM54140). Most of the times half the length is reported but sometimes
the length is correct.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the convenience function to do a read-modify-write. This has the
additional benefit of saving one write to the selection register.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helper to read and write expansion registers without taking the mdio
lock.
Please note, that this changes the semantics of the read and write.
Before there was no lock between selecting the expansion register and
the actual read/write. This may lead to access failures if there are
parallel accesses. Instead take the bus lock during the whole access
cycle.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GENET controller on the Raspberry Pi 4 (2711) is typically
interfaced with an external Broadcom PHY via a RGMII electrical
interface. To make sure that delays are properly configured at the PHY
side, ensure that we the dedicated Broadcom PHY driver
(CONFIG_BROADCOM_PHY) is enabled for this to happen.
Fixes: 402482a6a78e ("net: bcmgenet: Clear ID_MODE_DIS in EXT_RGMII_OOB_CTRL when not needed")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
