| Age | Commit message (Collapse) | Author |
|---|
|
The candleLight community is working on switchable termination support
for the candleLight firmware. As the the Linux CAN framework supports
switchable termination add this feature to the gs_usb driver.
Devices supporting the feature should set the
GS_CAN_FEATURE_TERMINATION and implement the
GS_USB_BREQ_SET_TERMINATION and GS_USB_BREQ_GET_TERMINATION control
messages.
For now the driver assumes for activated termination the standard
termination value of 120Ω.
Link: https://lore.kernel.org/all/20220923074114.662045-1-mkl@pengutronix.de
Link: https://github.com/candle-usb/candleLight_fw/issues/92
Link: https://github.com/candle-usb/candleLight_fw/pull/109
Link: https://github.com/candle-usb/candleLight_fw/pull/108
Cc: Daniel Trevitz <daniel.trevitz@wika.com>
Cc: Ryan Edwards <ryan.edwards@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Introduce a label to free the allocated candev in case of an error and
make use of if. Fix a memory leak if the extended bit timing cannot be
read. Extend the error messages to print the number of the failing
channel and the symbolic error name.
Link: https://lore.kernel.org/all/20220921193902.575416-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Convert the driver to use usb_control_msg_{send,recv}() instead of
usb_control_msg(). These functions allow the data to be placed on the
stack. This makes the driver a lot easier as we don't have to deal
with dynamically allocated memory.
Link: https://lore.kernel.org/all/20220921193902.575416-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
to dev
Most of the driver uses the variable "dev" to point to the struct
gs_can. Use the same name in gs_cmd_reset(), too. Rename gsdev to dev.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220921193902.575416-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
On busy networks the CAN controller might receive CAN frames directly
after starting it but before the timecounter is setup. This will lead
to NULL pointer deref while converting the converting the CAN frame's
timestamp with the timecounter.
Close the race window by setting up the timecounter before starting
the CAN controller.
Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220921081329.385509-1-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The struct timecounter::cycle_last is a 64 bit variable, read by
timecounter_cyc2time(), and written by timecounter_read(). On 32 bit
architectures this is not atomic.
Add a spinlock to protect access to struct timecounter::cycle_last. In
the gs_usb_timestamp_read() callback the lock is dropped to execute a
sleeping synchronous USB transfer. This is safe, as the variable we
want to protect is accessed during this call.
Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220920100416.959226-3-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk>
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
usb_control_msg_recv()
The 2nd argument of usb_control_msg_recv() is the "endpoint",
usb_control_msg_recv() will internally convert the endpoint into a
pipe with usb_rcvctrlpipe().
In gs_usb_get_timestamp() not the endpoint "0" is passed, but the
pipe. This worked by accident as endpoint is a __u8 and the lowest 8
bits of the pipe are 0. Fix this copy/paste error by using the correct
endpoint of "0".
Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220920100416.959226-2-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk>
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When GEM is in SGMII mode and disabled as a wakeup source, the power
management controller can power down the entire full power domain(FPD)
if none of the FPD devices are in use.
Incase of FPD off, there are below ethernet link up issues on non-wakeup
suspend/resume. To fix it add phy_exit() in suspend and phy_init() in the
resume path which reinitializes PS GTR SGMII lanes.
$ echo +20 > /sys/class/rtc/rtc0/wakealarm
$ echo mem > /sys/power/state
After resume:
$ ifconfig eth0 up
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
phy phy-fd400000.phy.0: phy poweron failed --> -110
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
SIOCSIFFLAGS: Connection timed out
phy phy-fd400000.phy.0: phy poweron failed --> -110
Fixes: 8b73fa3ae02b ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lan966x switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. Add support for TAS configuration on
egress port of lan966x switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add registers that are used by taprio to configure the HW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement mqprio qdisc support using tc command.
The HW supports 8 priority queues from highest (7) to lowest (0).
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a define for the number of priority queues on lan966x. Because there
will be more checks for this, so instead of using hardcoded value all
over the place add a define for this.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use kstrdup instead of open-coding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds support for not enabling carrier during TUNSETIFF
interface creation by specifying the IFF_NO_CARRIER flag.
Our tests make heavy use of tun interfaces. In some scenarios, the test
process creates the interface but another process brings it up after the
interface is discovered via netlink notification. In that case, it is
not possible to create a tun/tap interface with carrier off without it
racing against the bring up. Immediately setting carrier off via
TUNSETCARRIER is still too late.
Signed-off-by: Patrick Rohr <prohr@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read link status from SGMII PCS for in-band managed 2500Base-X and
1000Base-X connection on a MAC port of the MT7531. This is needed to
get the SFP cage working which is connected to SGMII interface of
port 5 of the MT7531 switch IC on the Bananapi BPi-R3 board.
While at it also handle an_complete for both the autoneg and the
non-autoneg codepath.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for rate matching for phys similar to the AQR107. We
assume that all phys using aqr107_read_status support rate matching.
However, it could be possible to determine support based on the firmware
revision if there are phys discovered which do not support rate
matching. However, as rate matching is advertised in the datasheets for
these phys, I suspect it is supported most boards.
Despite the name, the "config" registers are updated with the current
rate matching method (if any). Because they appear to be updated
automatically, I don't know if these registers can be used to disable
rate matching.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are documented in the AQR115 register reference. I haven't tested
them, but perhaps they'll be useful to someone.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for adjusting the advertisement for pause-based rate
matching. This may result in a lossy link, since the final link settings
are not adjusted. Asymmetric pause support is necessary. It would be
possible for a MAC supporting only symmetric pause to use pause-based rate
adaptation, but only if pause reception was enabled as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the phy is configured to use pause-based rate matching, ensure that
the link is full duplex with pause frame reception enabled. As
suggested, if pause-based rate matching is enabled by the phy, then
pause reception is unconditionally enabled.
The interface duplex is determined based on the rate matching type.
When rate matching is enabled, so is the speed. We assume the maximum
interface speed is used. This is only relevant for MLO_AN_PHY. For
MLO_AN_INBAND, the MAC/PCS's view of the interface speed will be used.
Although there are no RATE_ADAPT_CRS phys in-tree, it has been added for
comparison (and the implementation is quite simple).
Co-developed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we call phylink_caps_to_linkmodes directly from
phylink_get_linkmodes, it is difficult to re-use this functionality in
MAC drivers. This is because MAC drivers must then work with an ethtool
linkmode bitmap, instead of with mac capabilities. Instead, let the
caller of phylink_get_linkmodes do the conversion. To reflect this
change, rename the function to phylink_get_capabilities.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is convenient for MAC drivers. They can use it to add or
remove particular link modes based on capabilities (such as if half
duplex is not supported for a particular interface mode).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for offloading ets qdisc to sparx5 switch.
The ets qdisc makes it possible to configure a mix og strict and
bandwidth-sharing bands. The ets qdisc must be attached as a root qdisc.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for offloading tbf qdisc to sparx5 qdisc.
The tbf qdisc makes it possible to attach a shaper on traffic egressing
from a port or a queue. Per-port tbf qdiscs are attached as a root qdisc
directly and queue tbf qdiscs are attached to one of the classes of a
parent qdisc (such as mqprio).
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for offloading mqprio qdisc to sparx5 switch.
The offloaded mqprio qdisc currently does nothing by itself, but serves
as an attachment point for other qdiscs (tbf, ets etc.)
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add tc setup hook for QoS features.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary spi_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support setting replay window size for MACsec offload.
Currently supported window size of 32, 64, 128 and 256
bit. Other values will be returned as invalid parameter.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MACsec EPN splits the packet number (PN) into two 32-bits fields,
epn_lsb (32 least significant bits (LSBs) of PN) and epn_msb (32
most significant bits (MSBs) of PN).
Epn_msb bits are managed by SW and for that HW is required to send
an object change event of type EPN event notifying the SW to update
the epn_msb in addition, once epn_msb is updated SW update HW with
the new epn_msb value for HW to perform replay protection.
To prevent HW from stopping while handling the event, SW manages
another bit for HW called epn_overlap, HW uses the latter to get
an indication regarding how to read the epn_msb value correctly
while still receiving packets.
Add epn event handling that updates the epn_overlap and epn_msb for
every 2^31 packets according to the following logic:
if epn_lsb crosses 2^31 (half sequence number wraparound) upon HW
relevant event, SW updates the esn_overlap value to OLD (value = 1).
When the epn_lsb crosses 2^32 (full sequence number wraparound)
upon HW relevant event, SW updates the esn_overlap to NEW
(value = 0) and increment the esn_msb.
When using MACsec EPN a salt and short secure channel id (ssci)
needs to be provided by the user, when offloading EPN need to pass
this salt and ssci to the HW to be used in the initial vector (IV)
calculations.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
enable stage
Postpone MACsec initialization to the mlx5e profile enable stage to have
user access region (UAR) pages and other resources ready before MACsec
initialization to initialize advanced steering operation (ASO) hardware
resources.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for ASO work queue entry (WQE) data to allow reading
data upon querying the ASO work queue (WQ).
Register user mode memory registration (UMR) upon ASO WQ init,
de-register UMR upon ASO WQ cleanup.
MACsec uses UMR to determine the cause of the event triggered
by the HW since different scenarios could trigger the same event.
Setup MACsec ASO object to sync HW with SW about various macsec
flow stateful features like: replay window, lifetime limits e.t.c
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Expose mlx5e_create_mkey function, for future patches in the
macsec series to use.
The above function creates a memory key which describes a
region in memory that can be later used by both HW and SW.
The counterpart destroy functionality is already exposed.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently when creating MACsec object, next_pn which represents
the initial packet number (PN) is considered only in TX flow.
The above causes mismatch between TX and RX initial PN which
is reflected in packet drops.
Fix by considering next_pn in RX flow too.
Fixes: aae3454e4d4c ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
