| Age | Commit message (Collapse) | Author |
|---|
|
The eswitch offloads table, which has the reps (vport) rx miss rules,
was moved from OFFLOADS namespace [0,0] (prio, level), to [1,0], so
the restore table (the new [0,0]) can come before it. The destinations
of these miss rules is the rep root ft (ttc for non uplink reps).
Uplink rep root ft is created as OFFLOADS namespace [0,1], and is used
as a hook to next RX prio (either ethtool or ttc), but this fails to
pass fs_core level's check.
Move uplink rep root ft to OFFLOADS prio 1, level 1 ([1,1]), so it
will keep the same relative position after the restore table
change.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable reg c1 loopback if firmware reports it's supported,
as this is needed for restoring packet metadata (e.g chain).
Also define helper to query if it is enabled.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
|
|
Currently, PF missed to clear the port base VLAN for VF when
unload. In this case, the VLAN id will remain in the VLAN
table. This patch fixes it.
Fixes: 92f11ea177cd ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the user manual, the ingress and egress VLAN filter
are configured at the same time. Currently, hclge_init_vlan_config()
and hclge_set_vlan_spoofchk() will both change the VLAN filter
switch. So it's necessary to read the old configuration before
modifying it.
Fixes: 22044f95faa0 ("net: hns3: add support for spoof check setting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if VF is loaded on the host side, the host doesn't
clear the VF's VLAN table entries when VF removing. In this
case, when doing reset and disabling sriov at the same time the
VLAN device over VF will be removed, but the VLAN table entries
in hardware are remained.
This patch fixes it by asking PF to clear the VLAN table entries for
VF when VF is removing. It also clears the VLAN table full bit
after VF VLAN table entries being cleared.
Fixes: c6075b193462 ("net: hns3: Record VF vlan tables")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HNS3 driver supports to configure TC numbers and TC to priority
map via "tc" tool. But when delete the rule, will fail, because
the HNS3 driver needs at least one TC, but the "tc" tool sets TC
number to zero when delete.
This patch makes sure that the TC number is at least one.
Fixes: 30d240dfa2e8 ("net: hns3: Add mqprio hardware offload support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.
As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.
As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters
(other than adaptive rx, which will now be rejected by core).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Converting fallthrough comments to fallthrough; creates warnings
in this code when compiled with gcc.
This code is overly complicated and reads rather better with a
little refactoring and no fallthrough uses at all.
Remove the fallthrough comments and simplify the written source
code while reducing the object code size.
Consolidate duplicated switch/case blocks for IPV4 and IPV6.
defconfig x86-64 with sfc:
$ size drivers/net/ethernet/sfc/ethtool.o*
text data bss dec hex filename
10055 12 0 10067 2753 drivers/net/ethernet/sfc/ethtool.o.new
10135 12 0 10147 27a3 drivers/net/ethernet/sfc/ethtool.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit mentioned below added a stray plus sign, likely
due to some conflict resolution (i.e. as a leftover from a
unified diff), which was harmless since it was just used as
an integer constant modifier. Remove it anyway, now that I
stumbled across it.
Fixes: cf33a7728bf2 ("wlcore: mesh: Add support for RX Broadcast Key")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: b43-dev@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: b43-dev@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272df6 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
hard_header_len provides limitations for things like AF_PACKET, such
that we don't allow transmitting packets smaller than this.
needed_headroom provides a suggested minimum headroom for SKBs, so that
we can trivally add our headers to the front.
The latter is the correct field to use in this case, while the former
mostly just prevents sending small AF_PACKET frames.
In any case, mwifiex already does its own bounce buffering [1] if we
don't have enough headroom, so hints (not hard limits) are all that are
needed.
This is the essentially the same bug (and fix) that brcmfmac had, fixed
in commit cb39288fd6bb ("brcmfmac: use ndev->needed_headroom to reserve
additional header space").
[1] mwifiex_hard_start_xmit():
if (skb_headroom(skb) < MWIFIEX_MIN_DATA_HEADER_LEN) {
[...]
/* Insufficient skb headroom - allocate a new skb */
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.gbhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove unneeded variable ret used to store return value.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The simple_strtol() function is deprecated since it does not
check for the range overflow. Use kstrtoint() instead.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove unused fab_version member from struct rtw_hal.
Some of the checks being made were nonsense.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Firmware supports only STA as primary interface in repeater mode.
Since the only meaningful usage of AP + STA interface combination
is repeater, reject such combination with AP as primary interface.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Quantenna Pearl device exposes multiple (up to 3) radio interfaces under
single PCIe function. So far all the wiphy devices were attached to the
same pcie device. As a result, all different wireless network devices
were reported under the same sysfs directory for pcie device, e.g.:
$ ls /sys/class/net/wlan0/device/net/
wlan0 wlan1
It turns out that such behavior may confuse various users of wireless
subsystem. For instance, it turned out to be the case for:
- Linux init systems, e.g. for renaming based on parent device
- OpenWRT configuration scripts
Suggested solution is to add an intermediate virtual platform device
for each radio interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Make sure that edmg field of cfg80211_chan_def structure is properly
initialized by zeros. Otherwise cfg80211_chandef_valid may return
false if edmg fields contain some garbage.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable WPA3 OWE support in AP mode. Driver currently supports cards that
offload OWE processing to userspace. This patch adds all the required
tools for such offloading. Firmware requests OWE processing sending new
UPDATE_OWE event to driver, which uses cfg80211_update_owe_info_event to
notify userspace software. After OWE processing is completed, userspace
sends calculated IEs to firmware using update_owe_info cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable WPA3 SAE support in AP mode. Driver currently supports cards
that offload SAE authentication to userspace. So allow userspace
software to subscribe and to send AUTH frames. Besides, enable
AP mode support in external_auth cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For some unexplained reason, commit d1d1a96bdb44 ("rtlwifi: rtl8188ee:
Remove local configuration variable") broke at least one system. As
the only net effect of the change was to remove 2 bytes from the start
of struct phy_status_rpt, this patch adds 2 bytes of padding at the
beginning of the struct.
Fixes: d1d1a96bdb44 ("rtlwifi: rtl8188ee: Remove local configuration variable")
Cc: Stable <stable@vger.kernel.org> # V5.4+
Reported-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Tested-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: ath11k@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Hardwares tested : QCA9887
Firmwares tested : 10.4-3.9.0.1-00036
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ecdb ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7dfbb ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/ibm/emac/core.c: In function __emac_mdio_write:
drivers/net/ethernet/ibm/emac/core.c:875:9: warning:
variable err set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to play with gotos to jump over single statement.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an off-by-one error in strncpy size argument in
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c. The issue is that in:
strncmp(opt, "eee_timer:", 6)
the passed string literal: "eee_timer:" has 10 bytes (without the NULL
byte) and the passed size argument is 6. As a result, the logic will
also accept other, malformed strings, e.g. "eee_tiXXX:".
This bug doesn't seem to have any security impact since its present in
module's cmdline parsing code.
Signed-off-by: Dominik Czarnota <dominik.b.czarnota@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 319a1d19471e, stmmac only support basic HW stats type for
action. Set this field in the L3/L4 Filtering test so that it correctly
setups the filter instead of returning EOPNOTSUPP.
Fixes: 319a1d19471e ("flow_offload: check for basic action hw stats type")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
