| Age | Commit message (Collapse) | Author |
|---|
|
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new chip for RTL8106E series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The suggestion as following:
- initial settings or default settings
- rtl_hw_start_xxx. rtl_hw_start_xxx may change some default settings.
- enable tx/rx. This has to be after the above two steps.
- rtl_set_rx_mode. AcceptXXXs have to be enabled after enabling tx/rx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new chip for RTL8111G series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- replace rtl8168g-1.fw with rtl8168g-2.fw which support new method.
- fix PHY power down is useless.
- disable rx early which causes the rx abnormal.
- enable auto fifo.
- set 10M IFG to default value.
- fix the conflict between jumbo frame and flow control.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove useless action PHY_READ_EFUSE, PHY_READ_MAC_BYTE, PHY_WRITE_MAC_BYTE,
PHY_WRITE_ERI_WORD. And define the new action PHY_MDIO_CHG.
PHY_MDIO_CHG is used to modify the mdio operation. By the way, the
firmware could support setting mac ocp.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the new settings and correct the wrong settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the current settings with rtl_writephy and rtl_readphy.
For the hardware, the settings are same with previous ones. This
make the setting method like the previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some codes are belong to binary codes and should be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have a race condition if we try to rmmod bonding and simultaneously add
a bond master through sysfs. In bonding_exit() we first remove the devices
(through rtnl_link_unregister() ) and only after that we remove the sysfs.
If we manage to add a device through sysfs after that the devices were
removed - we'll end up with that device/sysfs structure and with the module
unloaded.
Fix this by first removing the sysfs and only after that calling
rtnl_link_unregister().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The limit of 0x3c00 is taken from the windows driver.
Suggested-by: Huang, Xiong <xiong@qca.qualcomm.com>
Cc: Huang, Xiong <xiong@qca.qualcomm.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It would cause no link after suspending or shutdowning when the
nic changes the speed to 10M and connects to a link partner which
forces the speed to 100M.
Check the link partner ability to determine which speed to set.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into wireless
John W. Linville says:
====================
Here are some more fixes intended for the 3.9 stream...
Regarding the mac80211 bits, Johannes says:
"I had changed the idle handling to simplify it, but broken the
sequencing of commands, at least for ath9k-htc, one patch restores the
sequence. The other patch fixes a crash Jouni found while stress-testing
the remain-on-channel code, when an item is deleted the work struct can
run twice and crash the second time."
As for the iwlwifi bits, Johannes says:
"The only fix here is to the passive-no-RX firmware regulatory
enforcement driver support code to not drop auth frames in quick
succession, leading to not being able to connect to APs on passive
channels in certain circumstances."
Don't forget the NFC bits, about which Samuel says:
"This time we have:
- A crash fix for when a DGRAM LLCP socket is listening while the NFC adapter
is physically removed.
- A potential double skb free when the LLCP socket receive queue is full.
- A fix for properly handling multiple and consecutive LLCP connections, and
not trash the socket ack log.
- A build failure for the MEI microread physical layer, now that the MEI bus
APIs have been merged into char-misc-next."
On top of that, Stone Piao provides an mwifiex fix to avoid accessing
beyond the end of a buffer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some MX28 boards need the internal enet_out clock to be enabled. So, do
this in the driver iff the clock was referenced via devicetree.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
When the optional clk_ptp is absent, we can just set it to NULL, and
clk API will just handle it gracefully. It saves us from checking
clk_ptp whenever calling into clk API.
Also since clk_ptp is optional, the "ret" variable shouldn't be set
in case that the clock is absent.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
It actually handles a BT coex notification, so rename it
to be more self explained.
Also, this function can always look at mvm->last_bt_notif
provided that the latter is updated on time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Using IWL_MVM_STATION_COUNT and IWL_INVALID_STATION together
isn't a good idea as they have different values. Always use
IWL_MVM_STATION_COUNT for an invalid station in MVM and move
the definition of the IWL_INVALID_STATION constant into the
DVM driver to avoid making such mistakes again. The one use
in the transport code can be hard-coded to -1 instead as the
station ID is passed as an integer there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
some new thinkpad laptops use intel chip with new pci id need be added
lspci -vnn output:
Network controller [0280]: Intel Corporation Centrino Advanced-N 6235
[8086:088f] (rev 24)
Subsystem: Intel Corporation Device [8086:5260]
Signed-off-by: Shuduo Sang <sangshuduo@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The iterators don't need to know what bt_kill_msk means.
All they need to know is if reduced Tx power is enabled
on an interface or not. So change the member of the
iterator to be a bool.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The firmware API changed to differentiate between event and
fragment start/end. Change the time-event handling accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Many platforms have issues processing a wakeup signal
while they're still suspending, and will ignore it.
Since our device thinks it woke the platform, and the
platform ignored the signal, it will sleep without
WoWLAN being enabled as the device disables WoWLAN
when having woken the platform.
Resolve this by making the device wait for 10 seconds
after getting the suspend signal before waking up the
platform.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Print the sub-driver (opmode, i.e. DVM or MVM) when the
firmware is loaded.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The function just wraps an existing one, remove it.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The requirement for TX/RX active to powersave transition time for
the Balanced Power Save (BPS) scheme changed. Change the driver
accordingly and set transition time to 100 msec.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Encapsulate the power table command logging in a separate
function to print the same information in both cases.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The firmware starts sending nulldata frames for keepalive immediately
after association, regardless of power management state. The driver
thus needs to configure keep alive period unconditionally.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The driver distinguishes between power management and device's power
down enablement. Power management enablement depends both on driver's
module power parameters and mac80211 decision. The device's power down
depends only on driver's module power parameters. Change the driver to
always send Power Table command to enable or disable both power
management and device's power down.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Active to power save mode transition time for TX/RX in the power
table command is in microseconds, fix the units in the driver.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently power management is supported only when only a single
virtual interface is present. The driver verifies number of created
interfaces and disables power management when multiple interfaces
present. However, this rule does not extend to a P2P device that is
handled differently in the firmware. If a P2P device is added power
management can remain enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Replace SLEEP_OVER_DTIM by SKIP_OVER_DTIM.
Add iwl_mvm prefix to a function name.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Current available FW still doesn't support new PM API.
Therefore, to enable basic power management with the
existing firmware, change the API in the driver back
to the API used in the current firmware.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When we roam to A band, we don't need to constraint WiFi
any more since it is operating on a different band.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows to have better wifi TPT when BT is active under
good RSSI conditions.
Wifi will have better chance to send Acks and Cts even if BT
is active.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Use the per-interface debugfs infrastructure to create a
directory and symlink, and add a file containing debug
data related to each virtual interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Firmware provides the driver with credits used to transmit packets
to the firmware. When credits run out the packets should be queued
and dequeued when receiving creditback signals from the firmware.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The fcmode provided by module parameter defaults to NONE, which
means no flow-control is required. In this case flow-control
signals should not be enabled.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Bail out of brcmf_fws_init() when no firmware-signalling is asked
for. Need to take this into account in brcmf_fws_deinit() as well.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The functions are moved in preparation of later patches.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The length is not according specification so better fix it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If iovar to the firmware fails the firmware-signalling module
does a cleanup for which it needs pointer to struct brcmf_pub, which
it gets from struct brcmf_fws_info::drvr. Assign this field before
doing the tlv iovar.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The low-level sdio code has a large number of trace and info messages
that are mostly useful looking into bus specific issues. For tracing
higher-level driver functions it is better to have a dedicated level
for low-level sdio debugging.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: Ia424ff18d9033b97aeffc248358e50c51805e815
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/74
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
During SDIO layer flow control signalling firmware can issue
invalid packets. Prevent printing of parsing errors in such case.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Parsing the tlv upon receiving frames can fail. Instead of printing
an error message, just count the parse failure. On some devices we
receive a lot of invalid tlv signals.
this commit will be squashed.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: I08e0f62c55e5028f9aa70c396d291679abd273c9
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/72
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When firmware-signalling is active the brcmf_txcomplete() does
a free of the sk_buff when transfer to firmware fails in the
bus-specific driver code. However, it should also cleanup the
packet from the hanger. This patch fixes that.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Enabling the tx status signalling, which requires packet tagging
before sending to the firmware and handling the tx status signal.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Upcoming patches will add firmware signalled flow control. Prepare
by adding the mode, which defaults to disable it. The mode can be
queried by brcmf_fws_fc_active() and set by a module parameter.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a callback to obtain packet queue from the bus-specific code
used to cleanup packet buffers from firmware-signalling code.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The hanger for firmware-signalling is used to retain information for
outstanding transmit packets that await tx status.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When an interface is deleted make sure to cleanup all packet
buffers related to that interface.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
