| Age | Commit message (Collapse) | Author |
|---|
|
Currently phy link up/down interrupt is enabled using the
LAN87xx_INTERRUPT_MASK register. In the lan87xx_read_status function,
phy link is determined using the T1_MODE_STAT_REG register comm_ready bit.
comm_ready bit is set using the loc_rcvr_status & rem_rcvr_status.
Whenever the phy link is up, LAN87xx_INTERRUPT_SOURCE link_up bit is set
first but comm_ready bit takes some time to set based on local and
remote receiver status.
As per the current implementation, interrupt is triggered using link_up
but the comm_ready bit is still cleared in the read_status function. So,
link is always down. Initially tested with the shared interrupt
mechanism with switch and internal phy which is working, but after
implementing interrupt controller it is not working.
It can fixed either by updating the read_status function to read from
LAN87XX_INTERRUPT_SOURCE register or enable the interrupt mask for
comm_ready bit. But the validation team recommends the use of comm_ready
for link detection.
This patch fixes by enabling the comm_ready bit for link_up in the
LAN87XX_INTERRUPT_MASK_2 register (MISC Bank) and link_down in
LAN87xx_INTERRUPT_MASK register.
Fixes: 8a1b415d70b7 ("net: phy: added ethtool master-slave configuration support")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220905152750.5079-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The stmmac has the possibility to automatically strip the padding/FCS for IEEE
802.3 type frames. This feature is enabled conditionally. Therefore, the stmmac
receive path has to have a determination logic whether the FCS has to be
stripped in software or not.
In fact, for DSA this ACS feature is disabled and the determination logic
doesn't check for it properly. For instance, when using DSA in combination with
an older stmmac (pre version 4), the FCS is not stripped by hardware or software
which is problematic.
So either add another check for DSA to the fast path or simply disable ACS
feature completely. The latter approach has been chosen, because most of the
time the FCS is stripped in software anyway and it removes conditionals from the
receive fast path.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/87v8q8jjgh.fsf@kurt/
Link: https://lore.kernel.org/r/20220905130155.193640-1-kurt@linutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When serdes lane support setting 25Gb/s or 50Gb/s speed and user wants to
set port speed as 50Gb/s, it can be setted as one 50Gb/s serdes lane or
two 25Gb/s serdes lanes.
So, this patch adds support to query and set lane number by ethtool
to satisfy this scenario.
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FEC statistics can be used to check the transmission quality of links.
This patch implements the get_fec_stats callback of ethtool_ops to support
querying FEC statistics by command "ethtool -I --show-fec eth0".
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add dump the map relation for dscp, priority and TC, and
the current tc map mode.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To support tx packets to select queue according to its dscp field after
setting dscp and tc map relationship, this patch implements
ndo_select_queue() to set skb->priority according to the user's setting
dscp and priority map relationship.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support config dscp map to tc by implementing ieee_setapp
and ieee_delapp of struct dcbnl_rtnl_ops. Driver will convert mapping
relationship from dscp-prio to dscp-tc.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-09-06 (i40e, iavf)
This series contains updates to i40e and iavf drivers.
Stanislaw adds support for new device id for i40e.
Jaroslaw tidies up some code around MSI-X configuration by adding/
reworking comments and introducing a couple of macros for i40e.
Michal resolves some races around reset and close by deferring and deleting
some pending AdminQ operations and reworking filter additions and deletions
during these operations for iavf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-09-06 (ice)
This series contains updates to ice driver only.
Tony reduces device MSI-X request/usage when entire request can't be fulfilled.
Michal adds check for reset when waiting for PTP offsets.
Paul refactors firmware version checks to use a common helper.
Christophe Jaillet changes a couple of local memory allocation to not
use the devm variant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of mtk_foe_entry_timestamp routine since it is no longer used.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if max hash configured in hw in mtk_ppe_hash_entry is
MTK_PPE_ENTRIES - 1, check theoretical OOB accesses in
mtk_ppe_check_skb routine
Fixes: c4f033d9e03e9 ("net: ethernet: mtk_eth_soc: rework hardware flow table management")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ib1 state to MTK_FOE_STATE_UNBIND in __mtk_foe_entry_clear routine.
Fixes: 33fc42de33278 ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the ability to add up to 16 MACsec offload interfaces
over the same physical interface
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the following statistics:
RX successfully decrypted MACsec packets:
macsec_rx_pkts : Number of packets decrypted successfully
macsec_rx_bytes : Number of bytes decrypted successfully
Rx dropped MACsec packets:
macsec_rx_pkts_drop : Number of MACsec packets dropped
macsec_rx_bytes_drop : Number of MACsec bytes dropped
TX successfully encrypted MACsec packets:
macsec_tx_pkts : Number of packets encrypted/authenticated successfully
macsec_tx_bytes : Number of bytes encrypted/authenticated successfully
Tx dropped MACsec packets:
macsec_tx_pkts_drop : Number of MACsec packets dropped
macsec_tx_bytes_drop : Number of MACsec bytes dropped
The above can be seen using:
ethtool -S <ifc> |grep macsec
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add offload support for MACsec SecY callbacks - add/update/delete.
add_secy is called when need to create a new MACsec interface.
upd_secy is called when source MAC address or tx SC was changed.
del_secy is called when need to destroy the MACsec interface.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MACsec driver need to distinguish to which offload device the MACsec
is target to, in order to handle them correctly.
This can be done by attaching a metadata_dst to a SKB with a SCI,
when there is a match on MACsec rule.
To achieve that, there is a map between fs_id to SCI, so for each RX SC,
there is a unique fs_id allocated when creating RX SC.
fs_id passed to device driver as metadata for packets that passed Rx
MACsec offload to aid the driver to retrieve the matching SCI.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rx flow steering consists of two flow tables (FTs).
The first FT (crypto table) have one default miss rule so non MACsec
offloaded packets bypass the MACSec tables.
All others flow table entries (FTEs) are divided to two equal groups
size, both of them are for MACsec packets:
The first group is for MACsec packets which contains SCI field in the
SecTAG header.
The second group is for MACsec packets which doesn't contain SCI,
where need to match on the source MAC address (only if the SCI
is built from default MACsec port).
Destination MAC address, ethertype and some of SecTAG fields
are also matched for both groups.
In case of match, invoke decrypt action on the packet.
For each MACsec Rx offloaded SA two rules are created: one with SCI
and one without SCI.
The second FT (check table) has two fixed rules:
One rule is for verifying that the previous offload actions were
finished successfully.
In this case, need to decap the SecTAG header and forward the packet
for further processing.
Another default rule for dropping packets that failed in the previous
decrypt actions.
The MACsec FTs are created on demand when the first MACsec rule is
added and destroyed when the last MACsec rule is deleted.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new namespace for MACsec RX flows.
Encrypted MACsec packets should be first decrypted and stripped
from MACsec header and then continues with the kernel's steering
pipeline.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a support for Connect-X MACsec offload Rx SA & SC commands:
add, update and delete.
SCs are created on demend and aren't limited by number and unique by SCI.
Each Rx SA must be associated with Rx SC according to SCI.
Follow-up patches will implement the Rx steering.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MACsec driver marks Tx packets for device offload using a dedicated
skb_metadata_dst which holds a 64 bits SCI number.
A previously set rule will match on this number so the correct SA is used
for the MACsec operation.
As device driver can only provide 32 bits of metadata to flow tables,
need to used a mapping from 64 bit to 32 bits marker or id,
which is can be achieved by provide a 32 bit unique flow id in the
control path, and used a hash table to map 64 bit to the unique id in the
datapath.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx flow steering consists of two flow tables (FTs).
The first FT (crypto table) has two fixed rules:
One default miss rule so non MACsec offloaded packets bypass the MACSec
tables, another rule to make sure that MACsec key exchange (MKE) traffic
passes unencrypted as expected (matched of ethertype).
On each new MACsec offload flow, a new MACsec rule is added.
This rule is matched on metadata_reg_a (which contains the id of the
flow) and invokes the MACsec offload action on match.
The second FT (check table) has two fixed rules:
One rule for verifying that the previous offload actions were
finished successfully and packet need to be transmitted.
Another default rule for dropping packets that were failed in the
offload actions.
The MACsec FTs should be created on demand when the first MACsec rule is
added and destroyed when the last MACsec rule is deleted.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changed EGRESS_KERNEL namespace to EGRESS_IPSEC and add new
namespace for MACsec TX.
This namespace should be the last namespace for transmitted packets.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for Connect-X MACsec offload Tx SA commands:
add, update and delete.
In Connect-X MACsec, a Security Association (SA) is added or deleted
via allocating a HW context of an encryption/decryption key and
a HW context of a matching SA (MACsec object).
When new SA is added:
- Use a separate crypto key HW context.
- Create a separate MACsec context in HW to include the SA properties.
Introduce a new compilation flag MLX5_EN_MACSEC for it.
Follow-up patches will implement the Tx steering.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support MACsec offload (and maybe some other crypto features
in the future), generalize flow action parameters / defines to be used by
crypto offlaods other than IPsec.
The following changes made:
ipsec_obj_id field at flow action context was changed to crypto_obj_id,
intreduced a new crypto_type field where IPsec is the default zero type
for backward compatibility.
Action ipsec_decrypt was changed to crypto_decrypt.
Action ipsec_encrypt was changed to crypto_encrypt.
IPsec offload code was updated accordingly for backward compatibility.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
offload
Move some MACsec infrastructure like defines and functions,
in order to avoid code duplication for future drivers which
implements MACsec offload.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ben Ben-Ishay <benishay@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like in the Tx changes, if there are more than one MACsec device with
the same MAC address as in the packet's destination MAC, the packet will
be forward only to this device and not neccessarly to the desired one.
Offloading device drivers will mark offloaded MACsec SKBs with the
corresponding SCI in the skb_metadata_dst so the macsec rx handler will
know to which port to divert those skbs, instead of wrongly solely
relaying on dst MAC address comparison.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current MACsec offload implementation, MACsec interfaces shares
the same MAC address by default.
Therefore, HW can't distinguish from which MACsec interface the traffic
originated from.
MACsec stack will use skb_metadata_dst to store the SCI value, which is
unique per Macsec interface, skb_metadat_dst will be used by the
offloading device driver to associate the SKB with the corresponding
offloaded interface (SCI).
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vsc9959_sched_speed_set
The read-modify-write of QSYS_TAG_CONFIG from vsc9959_sched_speed_set()
runs unlocked with respect to the other functions that access it, which
are vsc9959_tas_guard_bands_update(), vsc9959_qos_port_tas_set() and
vsc9959_tas_clock_adjust(). All the others are under ocelot->tas_lock,
so move the vsc9959_sched_speed_set() access under that lock as well, to
resolve the concurrency.
Fixes: 55a515b1f5a9 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tc-taprio
Experimentally, it looks like when QSYS_QMAXSDU_CFG_7 is set to 605,
frames even way larger than 601 octets are transmitted even though these
should be considered as oversized, according to the documentation, and
dropped.
Since oversized frame dropping depends on frame size, which is only
known at the EOF stage, and therefore not at SOF when cut-through
forwarding begins, it means that the switch cannot take QSYS_QMAXSDU_CFG_*
into consideration for traffic classes that are cut-through.
Since cut-through forwarding has no UAPI to control it, and the driver
enables it based on the mantra "if we can, then why not", the strategy
is to alter vsc9959_cut_through_fwd() to take into consideration which
tc's have oversize frame dropping enabled, and disable cut-through for
them. Then, from vsc9959_tas_guard_bands_update(), we re-trigger the
cut-through determination process.
There are 2 strategies for vsc9959_cut_through_fwd() to determine
whether a tc has oversized dropping enabled or not. One is to keep a bit
mask of traffic classes per port, and the other is to read back from the
hardware registers (a non-zero value of QSYS_QMAXSDU_CFG_* means the
feature is enabled). We choose reading back from registers, because
struct ocelot_port is shared with drivers (ocelot, seville) that don't
support either cut-through nor tc-taprio, and we don't have a felix
specific extension of struct ocelot_port. Furthermore, reading registers
from the Felix hardware is quite cheap, since they are memory-mapped.
Fixes: 55a515b1f5a9 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
one packet
The blamed commit broke tc-taprio schedules such as this one:
tc qdisc replace dev $swp1 root taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 \
sched-entry S 0x7f 990000 \
sched-entry S 0x80 10000 \
flags 0x2
because the gate entry for TC 7 (S 0x80 10000 ns) now has a static guard
band added earlier than its 'gate close' event, such that packet
overruns won't occur in the worst case of the largest packet possible.
Since guard bands are statically determined based on the per-tc
QSYS_QMAXSDU_CFG_* with a fallback on the port-based QSYS_PORT_MAX_SDU,
we need to discuss what happens with TC 7 depending on kernel version,
since the driver, prior to commit 55a515b1f5a9 ("net: dsa: felix: drop
oversized frames with tc-taprio instead of hanging the port"), did not
touch QSYS_QMAXSDU_CFG_*, and therefore relied on QSYS_PORT_MAX_SDU.
1 (before vsc9959_tas_guard_bands_update): QSYS_PORT_MAX_SDU defaults to
1518, and at gigabit this introduces a static guard band (independent
of packet sizes) of 12144 ns, plus QSYS::HSCH_MISC_CFG.FRM_ADJ (bit
time of 20 octets => 160 ns). But this is larger than the time window
itself, of 10000 ns. So, the queue system never considers a frame with
TC 7 as eligible for transmission, since the gate practically never
opens, and these frames are forever stuck in the TX queues and hang
the port.
2 (after vsc9959_tas_guard_bands_update): Under the sole goal of
enabling oversized frame dropping, we make an effort to set
QSYS_QMAXSDU_CFG_7 to 1230 bytes. But QSYS_QMAXSDU_CFG_7 plays
one more role, which we did not take into account: per-tc static guard
band, expressed in L2 byte time (auto-adjusted for FCS and L1 overhead).
There is a discrepancy between what the driver thinks (that there is
no guard band, and 100% of min_gate_len[tc] is available for egress
scheduling) and what the hardware actually does (crops the equivalent
of QSYS_QMAXSDU_CFG_7 ns out of min_gate_len[tc]). In practice, this
means that the hardware thinks it has exactly 0 ns for scheduling tc 7.
In both cases, even minimum sized Ethernet frames are stuck on egress
rather than being considered for scheduling on TC 7, even if they would
fit given a proper configuration. Considering the current situation,
with vsc9959_tas_guard_bands_update(), frames between 60 octets and 1230
octets in size are not eligible for oversized dropping (because they are
smaller than QSYS_QMAXSDU_CFG_7), but won't be considered as eligible
for scheduling either, because the min_gate_len[7] (10000 ns) minus the
guard band determined by QSYS_QMAXSDU_CFG_7 (1230 octets * 8 ns per
octet == 9840 ns) minus the guard band auto-added for L1 overhead by
QSYS::HSCH_MISC_CFG.FRM_ADJ (20 octets * 8 ns per octet == 160 octets)
leaves 0 ns for scheduling in the queue system proper.
Investigating the hardware behavior, it becomes apparent that the queue
system needs precisely 33 ns of 'gate open' time in order to consider a
frame as eligible for scheduling to a tc. So the solution to this
problem is to amend vsc9959_tas_guard_bands_update(), by giving the
per-tc guard bands less space by exactly 33 ns, just enough for one
frame to be scheduled in that interval. This allows the queue system to
make forward progress for that port-tc, and prevents it from hanging.
Fixes: 297c4de6f780 ("net: dsa: felix: re-enable TAS guard band mode")
Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous patch add support for PTP over IPv6/UDP (only for 8000
series and newer) and this one add support for PTP over 802.3.
Tested: sync as master and as slave is correct with ptp4l. PTP over IPv4
and IPv6 still works fine.
Suggested-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit bd4a2697e5e2 ("sfc: use hardware tx timestamps for more than
PTP") added support for hardware timestamping on TX for cards of the
8000 series and newer, in an effort to provide support for other
transports other than IPv4/UDP.
However, timestamping was still not working on RX for these other
transports. This patch add support for PTP over IPv6/UDP.
Tested: sync as master and as slave is correct using ptp4l from linuxptp
package, both with IPv4 and IPv6.
Suggested-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for the support of PTP over IPv6/UDP and Ethernet in next
patches, allow a more flexible way of adding and removing RX filters for
PTP. Right now, only 2 filters are allowed, which are the ones needed
for PTP over IPv4/UDP.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding support for the LAN9354 device by allowing it to use
the LAN9303 DSA driver. These devices have the same underlying
access and control methods and from a feature set point of view
the LAN9354 is a superset of the LAN9303.
The MDIO access method has been tested on a SAMA5D3-EDS board
with a LAN9354 RMII daughter card.
While the SPI access method should also be the same, it has not
been tested and as such is not included at this time.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add initial BYTE_ORDER read to sync the 32-bit accesses over the 16-bit
mdio bus to improve driver robustness.
The lan9303 expects two mdio read transactions back-to-back to read a
32-bit register. The first read transaction causes the other half of the
32-bit register to get latched. The subsequent read returns the latched
second half of the 32-bit read. The BYTE_ORDER register is an exception to
this rule. As it is a constant value, there is no need to latch the second
half. We read this register first in case there were reads during the boot
loader process that might have occurred prior to this driver taking over
ownership of accessing this device.
This patch has been tested on the SAMA5D3-EDS with a LAN9303 RMII daughter
card.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add register validation for KSZ9896.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
regmap_access_tables
According to the KSZ9477S datasheet, there is no global register
at 0x033C and 0x033D addresses.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9896 supports both SPI (already in) and I2C.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver.
Although the KSZ9896 is already listed in the device tree binding
documentation since a1c0ed24fe9b (dt-bindings: net: dsa: document
additional Microchip KSZ9477 family switches) the chip id
(0x00989600) is not recognized by ksz_switch_detect() and rejected
by the driver.
The KSZ9896 is similar to KSZ9897 but has only one configurable
MII/RMII/RGMII/GMII cpu port.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query ADV_VIRTUALIZATION capabilities which provide information for
advanced virtualization related features.
Current capabilities refer to the page tracker object which is used for
tracking the pages that are dirtied by the device.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20220905105852.26398-3-yishaih@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Enable remain on channel support on WCN6750 as it is needed for
GAS, Passpoint.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080656.3450-1-quic_mpubbise@quicinc.com
|
|
There's a TODO here, just move the dependency on phy->rev
into the comment. Not that this driver is likely to get
any updates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.ea00a892e41b.I709217fc307125f8670c7f6a9093111b46194131@changeid
|
|
Instead of the code here that copies into a variable
first and then flips endianness, which confuses sparse,
just directly use get_unaligned_le64().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.a5c9ea122f0f.If786a66f8fd9d45659cd5a2532cf395e21334453@changeid
|
|
We can call this in one of two ways: through mac80211, where
we're already in an RCU read-side critical section, or from
some other code in the driver where this pointer can only be
NULL. In any case, we get a 'free' already protected pointer
to the sta through info->control.sta, so we can use it on
the stack without any further protection.
Remove the rcu_dereference() and critical section.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.e5bc20dd17bf.Ib570ff7fde33c2b6eddef493a3541fa04eb47181@changeid
|
|
These cause sparse warnings, and since the device generally
works in little endian we can assume the code is correct, so
just fix the casts accordingly. No binary changes on x86.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.3f72609a3825.If4048592701bf04981be1dab18eaaa339b2ea382@changeid
|
|
Clearly the value should be converted and then compared,
not the result of the comparison be converted. No binary
changes on x86.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.a32e45adb2b2.I8c966b07c0bf7be4485967b044d9dad3f4772a27@changeid
|
|
We need to read a value from the device to wake it, but if it
succeeds we don't really care about it. Mark the variable to
avoid a compiler warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.5d67f55178a1.If0789ab326935896e5886fa06dbb9ef0da6c0b41@changeid
|
|
This caused sparse warnings, and clearly is needed per
how other firmware interfaces behave.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.2b5cb713cf4b.Ibabba2deb7bb22863d3a134e7a3333422d7eff17@changeid
|
|
- endian swapping is required in one place, use the
already swapped 'bsssize' local
- lbs_disablemesh need not be exported and can be static
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.76c34b2ae7a0.Ieb97c72b6d26f9d695cc4ab10fa7af5c3509612b@changeid
|
|
Just remove the extra asterisk to make it not be
kernel-doc formatted.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.8169e8c9090c.I0357e80cc86be2d4ac6205d1f53568444dcf7c9b@changeid
|
