| Age | Commit message (Collapse) | Author |
|---|
|
Re-schedule napi after napi_complete() for tx, if it is necessay.
In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop the tx when the napi is disabled to prevent napi_schedule() is
called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust the setting of the flag of SELECTIVE_SUSPEND to prevent start_xmit()
from calling napi_schedule() directly during runtime suspend.
After calling napi_disable() or clearing the flag of WORK_ENABLE,
scheduling the napi is useless.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PIO buffer allocation can fail for two valid reasons:
- we've run out of them (results in -ENOSPC)
- the NIC configuration doesn't support them (results in -EPERM)
Since both these failures are expected netif_err is excessive.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For DLMs and SLMs on 80/81/83xx, many lane configurations
across different boards are coming up. Also kernel doesn't have
any way to identify board type/info and since firmware does,
just get rid of figuring out lane to serdes config and take
whatever has been programmed by low level firmware.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support to set Rx/Tx queue sizes from ethtool. Fixes
an issue with retrieving queue size. Also sets SQ's CQ_LIMIT
based on configured Tx queue size such that HW doesn't process
SQEs when there is no sufficient space in CQ.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
<linux/phy.h> includes <linux/phy_led_triggers.h>, which is not really
needed. Drop the include from <linux/phy.h>, and add it to all users
that didn't include it explicitly.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_attach_direct() ignores errors returned by
phy_led_triggers_register(). I think that's OK, as LED triggers can be
considered a non-critical feature.
However, this causes problems later:
- phy_led_trigger_change_speed() will access the array
phy_device.phy_led_triggers, which has been freed in the error path
of phy_led_triggers_register(), which may lead to a crash.
- phy_led_triggers_unregister() will access the same array, leading to
crashes during s2ram or poweroff, like:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
...
[<c04116d4>] (__list_del_entry_valid) from [<c05e8948>] (led_trigger_unregister+0x34/0xcc)
[<c05e8948>] (led_trigger_unregister) from [<c05336c4>] (phy_led_triggers_unregister+0x28/0x34)
[<c05336c4>] (phy_led_triggers_unregister) from [<c0531d44>] (phy_detach+0x30/0x74)
[<c0531d44>] (phy_detach) from [<c0538bdc>] (sh_eth_close+0x64/0x9c)
[<c0538bdc>] (sh_eth_close) from [<c04d4ce0>] (dpm_run_callback+0x48/0xc8)
or:
list_del corruption. prev->next should be dede6540, but was 2e323931
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:52!
...
[<c02f6d70>] (__list_del_entry_valid) from [<c0425168>] (led_trigger_unregister+0x34/0xcc)
[<c0425168>] (led_trigger_unregister) from [<c03a05a0>] (phy_led_triggers_unregister+0x28/0x34)
[<c03a05a0>] (phy_led_triggers_unregister) from [<c039ec04>] (phy_detach+0x30/0x74)
[<c039ec04>] (phy_detach) from [<c03a4fc0>] (sh_eth_close+0x6c/0xa4)
[<c03a4fc0>] (sh_eth_close) from [<c0483234>] (__dev_close_many+0xac/0xd0)
To fix this, clear phy_device.phy_num_led_triggers in the error path of
phy_led_triggers_register() fails.
Note that the "No phy led trigger registered for speed" message will
still be printed on link speed changes, which is a good cue that
something went wrong with the LED triggers.
Fixes: 2e0bc452f4721520 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_get_port_module_status() calls bnxt_update_link() which expects
RTNL to be held. In bnxt_sp_task() that does not hold RTNL, we need to
call it with a prior call to bnxt_rtnl_lock_sp() and the call needs to
be moved to the end of bnxt_sp_task().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_update_link() is called from multiple code paths. Most callers,
such as open, ethtool, already hold RTNL. Only the caller bnxt_sp_task()
does not. So it is a bug to take RTNL inside bnxt_update_link().
Fix it by removing the RTNL inside bnxt_update_link(). The function
now expects the caller to always hold RTNL.
In bnxt_sp_task(), call bnxt_rtnl_lock_sp() before calling
bnxt_update_link(). We also need to move the call to the end of
bnxt_sp_task() since it will be clearing the BNXT_STATE_IN_SP_TASK bit.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bnxt_sp_task(), we set a bit BNXT_STATE_IN_SP_TASK so that bnxt_close()
will synchronize and wait for bnxt_sp_task() to finish. Some functions
in bnxt_sp_task() require us to clear BNXT_STATE_IN_SP_TASK and then
acquire rtnl_lock() to prevent race conditions.
There are some bugs related to this logic. This patch refactors the code
to have common bnxt_rtnl_lock_sp() and bnxt_rtnl_unlock_sp() to handle
the RTNL and the clearing/setting of the bit. Multiple functions will
need the same logic. We also need to move bnxt_reset() to the end of
bnxt_sp_task(). Functions that clear BNXT_STATE_IN_SP_TASK must be the
last functions to be called in bnxt_sp_task(). The common scheme will
handle the condition properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace rumtime with runtime.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This work adds a number of tracepoints to paths that are either
considered slow-path or exception-like states, where monitoring or
inspecting them would be desirable.
For bpf(2) syscall, tracepoints have been placed for main commands
when they succeed. In XDP case, tracepoint is for exceptions, that
is, f.e. on abnormal BPF program exit such as unknown or XDP_ABORTED
return code, or when error occurs during XDP_TX action and the packet
could not be forwarded.
Both have been split into separate event headers, and can be further
extended. Worst case, if they unexpectedly should get into our way in
future, they can also removed [1]. Of course, these tracepoints (like
any other) can be analyzed by eBPF itself, etc. Example output:
# ./perf record -a -e bpf:* sleep 10
# ./perf script
sock_example 6197 [005] 283.980322: bpf:bpf_map_create: map type=ARRAY ufd=4 key=4 val=8 max=256 flags=0
sock_example 6197 [005] 283.980721: bpf:bpf_prog_load: prog=a5ea8fa30ea6849c type=SOCKET_FILTER ufd=5
sock_example 6197 [005] 283.988423: bpf:bpf_prog_get_type: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
sock_example 6197 [005] 283.988443: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[06 00 00 00] val=[00 00 00 00 00 00 00 00]
[...]
sock_example 6197 [005] 288.990868: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[01 00 00 00] val=[14 00 00 00 00 00 00 00]
swapper 0 [005] 289.338243: bpf:bpf_prog_put_rcu: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
[1] https://lwn.net/Articles/705270/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-24-01
The first seven patches from Or Gerlitz in this series further enhances
the mlx5 SRIOV switchdev mode to support offloading IPv6 tunnels using the
TC tunnel key set (encap) and unset (decap) actions.
Or Gerlitz says:
========================
As part of doing this change, few cleanups are done in the IPv4 code,
later we move to use the full tunnel key info provided to the driver as
the key for our internal hashing which is used to identify cases where
the same tunnel is used for encapsulating multiple flows. As done in the
IPv4 case, the control path for offloading IPv6 tunnels uses route/neigh
lookups and construction of the IPv6 tunnel headers on the encap path and
matching on the outer hears in the decap path.
The last patch of the series enlarges the HW FDB size for the switchdev mode,
so it has now room to contain offloaded flows as many as min(max number
of HW flow counters supported, max HW table size supported).
========================
Next to Or's series you can find several patches handling several topics.
From Mohamad, add support for SRIOV VF min rate guarantee by using the
TSAR BW share weights mechanism.
From Or, Two patches to enable Eth VFs to query their min-inline value for
user-space.
for that we move a mlx5 low level min inline helper function from mlx5
ethernet driver into the core driver and then use it in mlx5_ib to expose
the inline mode to rdma applications through libmlx5.
From Kamal Heib, Reduce memory consumption on kdump kernel.
From Shaker Daibes, code reuse in CQE compression control logic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To improve performance, netvsc can call network stack directly and
avoid the local backlog queue. This is safe since incoming packets are
handled in softirq context already because the receive function
callback is called from a tasklet.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kernel for_each_clear_bit macro to simplify finding next
available send section.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report packets and bytes transferred through a vmbus channel via ethtool.
This supersedes need for per-cpu statistics.
Example:
$ ethtool -S eth0
NIC statistics:
...
tx_queue_0_packets: 3523179
tx_queue_0_bytes: 505370920
rx_queue_0_packets: 41430490
rx_queue_0_bytes: 62714661254
tx_queue_1_packets: 0
tx_queue_1_bytes: 0
rx_queue_1_packets: 0
rx_queue_1_bytes: 0
...
Reviewed-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Simon Xiao <sixiao@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most drivers do not increment transmit statistics until after the
transmit is completed. This will also be necessary for BQL support.
Slight additional complexity because the netvsc driver aggregates
multiple packets into one transmit.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since now keep track of per-queue outstanding sends, we can avoid
one atomic update by removing no longer needed per-device atomic.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All caller's already have pointer to netvsc_device so pass it.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the caller's/callee's know that the format of the device_add
parameter is a netvsc_device_info struct.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do manual optimizations of receive path:
- remove checks for impossible conditions (but keep checks
for bad data from host)
- pass argument down, rather than having callee recompute what
is already known
- remove indirection about receive buffer datalength
- remove dependence on VLAN_TAG_PRESENCE
- use _hot/_cold and likely/unlikely
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Put all the per-channel state together in one data struct.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes set but never used warnings
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netvsc select queue function was missing many of the flow caching
features that exist in default tx queue selection. Add the same
logic to remember queue based on socket and implement two level
mapping (like RSS).
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow setting receive indirection table. Also uses the system standard
for initialization.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows for number of channels to be managed in a manner similar
to existing hardware drivers. It also removes the restriction of
maximum 8 channels and allows as many as the host will allow.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some cases it is useful to be able to change RSS key value.
For example, replacing RSS key with a symmetric hash.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report current components used in RSS hash.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report actual number of receive queues to ethtool.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Redo how Hyper-V network driver negotiates offload features. Query the
host to determine offload settings, and use the result.
Also:
* disable IPv4 header checksum offload (not used by Linux)
* enable TSO only if host supports
* enable UDP checksum offload if supported
* don't advertise support for checksumming of non-IP protocols
* adjust GSO maximum segment size
* enable HIGHDMA
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ring buffer mapping now handles the wraparound case
inside get_next_pkt_raw. Therefore it is not necessary to have an
additional special receive staging buffer.
See commit 1562edaed8c164ca5199 ("Drivers: hv: ring_buffer: count on
wrap around mappings")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With all the infrastructure in place, implement access to the external
MDIO bus on the 6390 family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6390 has multiple MDIO busses. Generalize the parsing of the
device tree to support multiple mdio nodes. The external mdio bus has
a compatible strings to indicate it is external.
Keep a linked list of busses, placing the external mdio bus at the
tail of the list. When within the driver an mdio bus is needed,
e.g. for EEE or SERDES, use the head of the list which should be the
internal bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Have the MDIO bus driver code allocate a private structure and make
the chip a member of it. This will allow us to add further members in
the future.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for supporting multiple MDIO busses, pass the mii_bus
structure to all PHY operations. It will in future then be clear on
which MDIO bus the operation should be performed.
For reads/write from phylib, the mii_bus is readily available. However
some internal code also access the PHY, e.g. for EEE and SERDES. Make
this code use the one and only currently available MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6165 family has the internal PHYs mapped directly onto the
SMI register space as the switch. So the registers can be read
directly. Put a wrapper around this, in preparation for changing the
signature in order to support the external MDIO bus of the 6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If requesting msi-x interrupts fails in alx_request_irq we fall back to
a single tx queue and msi or legacy interrupts.
Currently the adapter stops working in this case and we get tx watchdog
timeouts. For reasons unknown the adapter gets confused when we load the
dma adresses to the chip in alx_init_ring_ptrs twice: the first time with
multiple queues and the second time in the fallback case with a single
queue.
To fix this move the the call to alx_reinit_rings (which calls
alx_init_ring_ptrs) after alx_request_irq. At this time it is clear how
much tx queues we have and which dma addresses we use.
Fixes: d768319cd427 ("alx: enable multiple tx queues")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If requesting msi-x interrupts fails we should fall back to msi or
legacy interrupts. However alx_realloc_ressources don't call
alx_init_intr, so we fail to set the right number of tx queues.
This results in watchdog timeouts and a nonfunctional adapter.
Fixes: d768319cd427 ("alx: enable multiple tx queues")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The condition to free the descriptor memory is wrong, we want to free the
memory if it is set and not if it is unset. Invert the test to fix this
issue.
Fixes: b0999223f224b ("alx: add ability to allocate and free alx_napi structures")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Another rebranded Novatel E371. qmi_wwan should drive this device, while
cdc_ether should ignore it. Even though the USB descriptors are plain
CDC-ETHER that USB interface is a QMI interface. Ref commit 7fdb7846c9ca
("qmi_wwan/cdc_ether: add device IDs for Dell 5804 (Novatel E371) WWAN
card")
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:
ibmveth 71000003 (unregistered net_device): unable to change
checksum offload settings. 1 rc=-2 ret_attr=71000003
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify the drivers/net/ethernet/{Makefile,Kconfig} file to make them a
part of the network drivers build.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add definitions that support receive side scaling.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the driver interfaces required for support by the ethtool utility.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add functions to interface with the hardware and some utility functions.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add common functions for Atlantic hardware abstraction layer.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add functions that handle the PCI bus interface.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add functions to manululate the vector of receive and transmit rings.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel.Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
