| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from Bluetooth.
Current release - regressions:
- ipv4: fix regression in local-broadcast routes
- vsock: fix error-handling regression introduced in v6.17-rc1
Previous releases - regressions:
- bluetooth:
- mark connection as closed during suspend disconnect
- fix set_local_name race condition
- eth:
- ice: fix NULL pointer dereference on reset
- mlx5: fix memory leak in hws_pool_buddy_init error path
- bnxt_en: fix stats context reservation logic
- hv: fix loss of receive events from host during channel open
Previous releases - always broken:
- page_pool: fix incorrect mp_ops error handling
- sctp: initialize more fields in sctp_v6_from_sk()
- eth:
- octeontx2-vf: fix max packet length errors
- idpf: fix Tx flow scheduling to avoid Tx timeouts
- bnxt_en: fix memory corruption during ifdown
- ice: fix incorrect counter for buffer allocation failures
- mlx5: fix lockdep assertion on sync reset unload event
- fbnic: fixup rtnl_lock and devl_lock handling
- xgmac: do not enable RX FIFO overflow interrupts
- phy: mscc: fix when PTP clock is register and unregister
Misc:
- add Telit Cinterion LE910C4-WWX new compositions"
* tag 'net-6.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (60 commits)
net: ipv4: fix regression in local-broadcast routes
net: macb: Disable clocks once
fbnic: Move phylink resume out of service_task and into open/close
fbnic: Fixup rtnl_lock and devl_lock handling related to mailbox code
net: rose: fix a typo in rose_clear_routes()
l2tp: do not use sock_hold() in pppol2tp_session_get_sock()
sctp: initialize more fields in sctp_v6_from_sk()
MAINTAINERS: rmnet: Update email addresses
net: rose: include node references in rose_neigh refcount
net: rose: convert 'use' field to refcount_t
net: rose: split remove and free operations in rose_remove_neigh()
net: hv_netvsc: fix loss of early receive events from host during channel open.
net: stmmac: Set CIC bit only for TX queues with COE
net: stmmac: xgmac: Correct supported speed modes
net: stmmac: xgmac: Do not enable RX FIFO Overflow interrupts
net/mlx5e: Set local Xoff after FW update
net/mlx5e: Update and set Xon/Xoff upon port speed set
net/mlx5e: Update and set Xon/Xoff upon MTU set
net/mlx5: Prevent flow steering mode changes in switchdev mode
net/mlx5: Nack sync reset when SFs are present
...
|
|
When the driver is removed the clocks are disabled twice: once in
macb_remove and a second time by runtime pm. Disable wakeup in remove so
all the clocks are disabled and skip the second call to macb_clks_disable.
Always suspend the device as we always set it active in probe.
Fixes: d54f89af6cc4 ("net: macb: Add pm runtime support")
Signed-off-by: Neil Mandir <neil.mandir@seco.com>
Co-developed-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250826143022.935521-1-sean.anderson@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The fbnic driver was presenting with the following locking assert coming
out of a PM resume:
[ 42.208116][ T164] RTNL: assertion failed at drivers/net/phy/phylink.c (2611)
[ 42.208492][ T164] WARNING: CPU: 1 PID: 164 at drivers/net/phy/phylink.c:2611 phylink_resume+0x190/0x1e0
[ 42.208872][ T164] Modules linked in:
[ 42.209140][ T164] CPU: 1 UID: 0 PID: 164 Comm: bash Not tainted 6.17.0-rc2-virtme #134 PREEMPT(full)
[ 42.209496][ T164] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-5.fc42 04/01/2014
[ 42.209861][ T164] RIP: 0010:phylink_resume+0x190/0x1e0
[ 42.210057][ T164] Code: 83 e5 01 0f 85 b0 fe ff ff c6 05 1c cd 3e 02 01 90 ba 33 0a 00 00 48 c7 c6 20 3a 1d a5 48 c7 c7 e0 3e 1d a5 e8 21 b8 90 fe 90 <0f> 0b 90 90 e9 86 fe ff ff e8 42 ea 1f ff e9 e2 fe ff ff 48 89 ef
[ 42.210708][ T164] RSP: 0018:ffffc90000affbd8 EFLAGS: 00010296
[ 42.210983][ T164] RAX: 0000000000000000 RBX: ffff8880078d8400 RCX: 0000000000000000
[ 42.211235][ T164] RDX: 0000000000000000 RSI: 1ffffffff4f10938 RDI: 0000000000000001
[ 42.211466][ T164] RBP: 0000000000000000 R08: ffffffffa2ae79ea R09: fffffbfff4b3eb84
[ 42.211707][ T164] R10: 0000000000000003 R11: 0000000000000000 R12: ffff888007ad8000
[ 42.211997][ T164] R13: 0000000000000002 R14: ffff888006a18800 R15: ffffffffa34c59e0
[ 42.212234][ T164] FS: 00007f0dc8e39740(0000) GS:ffff88808f51f000(0000) knlGS:0000000000000000
[ 42.212505][ T164] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 42.212704][ T164] CR2: 00007f0dc8e9fe10 CR3: 000000000b56d003 CR4: 0000000000772ef0
[ 42.213227][ T164] PKRU: 55555554
[ 42.213366][ T164] Call Trace:
[ 42.213483][ T164] <TASK>
[ 42.213565][ T164] __fbnic_pm_attach.isra.0+0x8e/0xa0
[ 42.213725][ T164] pci_reset_function+0x116/0x1d0
[ 42.213895][ T164] reset_store+0xa0/0x100
[ 42.214025][ T164] ? pci_dev_reset_attr_is_visible+0x50/0x50
[ 42.214221][ T164] ? sysfs_file_kobj+0xc1/0x1e0
[ 42.214374][ T164] ? sysfs_kf_write+0x65/0x160
[ 42.214526][ T164] kernfs_fop_write_iter+0x2f8/0x4c0
[ 42.214677][ T164] ? kernfs_vma_page_mkwrite+0x1f0/0x1f0
[ 42.214836][ T164] new_sync_write+0x308/0x6f0
[ 42.214987][ T164] ? __lock_acquire+0x34c/0x740
[ 42.215135][ T164] ? new_sync_read+0x6f0/0x6f0
[ 42.215288][ T164] ? lock_acquire.part.0+0xbc/0x260
[ 42.215440][ T164] ? ksys_write+0xff/0x200
[ 42.215590][ T164] ? perf_trace_sched_switch+0x6d0/0x6d0
[ 42.215742][ T164] vfs_write+0x65e/0xbb0
[ 42.215876][ T164] ksys_write+0xff/0x200
[ 42.215994][ T164] ? __ia32_sys_read+0xc0/0xc0
[ 42.216141][ T164] ? do_user_addr_fault+0x269/0x9f0
[ 42.216292][ T164] ? rcu_is_watching+0x15/0xd0
[ 42.216442][ T164] do_syscall_64+0xbb/0x360
[ 42.216591][ T164] entry_SYSCALL_64_after_hwframe+0x4b/0x53
[ 42.216784][ T164] RIP: 0033:0x7f0dc8ea9986
A bit of digging showed that we were invoking the phylink_resume as a part
of the fbnic_up path when we were enabling the service task while not
holding the RTNL lock. We should be enabling this sooner as a part of the
ndo_open path and then just letting the service task come online later.
This will help to enforce the correct locking and brings the phylink
interface online at the same time as the network interface, instead of at a
later time.
I tested this on QEMU to verify this was working by putting the system to
sleep using "echo mem > /sys/power/state" to put the system to sleep in the
guest and then using the command "system_wakeup" in the QEMU monitor.
Fixes: 69684376eed5 ("eth: fbnic: Add link detection")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/175616257316.1963577.12238158800417771119.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The exception handling path for the __fbnic_pm_resume function had a bug in
that it was taking the devlink lock and then exiting to exception handling
instead of waiting until after it released the lock to do so. In order to
handle that I am swapping the placement of the unlock and the exception
handling jump to label so that we don't trigger a deadlock by holding the
lock longer than we need to.
In addition this change applies the same ordering to the rtnl_lock/unlock
calls in the same function as it should make the code easier to follow if
it adheres to a consistent pattern.
Fixes: 82534f446daa ("eth: fbnic: Add devlink dev flash support")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/175616256667.1963577.5543500806256052549.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The hv_netvsc driver currently enables NAPI after opening the primary and
subchannels. This ordering creates a race: if the Hyper-V host places data
in the host -> guest ring buffer and signals the channel before
napi_enable() has been called, the channel callback will run but
napi_schedule_prep() will return false. As a result, the NAPI poller never
gets scheduled, the data in the ring buffer is not consumed, and the
receive queue may remain permanently stuck until another interrupt happens
to arrive.
Fix this by enabling NAPI and registering it with the RX/TX queues before
vmbus channel is opened. This guarantees that any early host signal after
open will correctly trigger NAPI scheduling and the ring buffer will be
drained.
Fixes: 76bb5db5c749d ("netvsc: fix use after free on module removal")
Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Link: https://patch.msgid.link/20250825115627.GA32189@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, in the AF_XDP transmit paths, the CIC bit of
TX Desc3 is set for all packets. Setting this bit for
packets transmitting through queues that don't support
checksum offloading causes the TX DMA to get stuck after
transmitting some packets. This patch ensures the CIC bit
of TX Desc3 is set only if the TX queue supports checksum
offloading.
Fixes: 132c32ee5bc0 ("net: stmmac: Add TX via XDP zero-copy socket")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Link: https://patch.msgid.link/20250825-xgmac-minor-fixes-v3-3-c225fe4444c0@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct supported speed modes as per the XGMAC databook.
Commit 9cb54af214a7 ("net: stmmac: Fix IP-cores specific
MAC capabilities") removes support for 10M, 100M and
1000HD. 1000HD is not supported by XGMAC IP, but it does
support 10M and 100M FD mode for XGMAC version >= 2_20,
and it also supports 10M and 100M HD mode if the HDSEL bit
is set in the MAC_HW_FEATURE0 reg. This commit enables support
for 10M and 100M speed modes for XGMAC IP based on XGMAC
version and MAC capabilities.
Fixes: 9cb54af214a7 ("net: stmmac: Fix IP-cores specific MAC capabilities")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Link: https://patch.msgid.link/20250825-xgmac-minor-fixes-v3-2-c225fe4444c0@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enabling RX FIFO Overflow interrupts is counterproductive
and causes an interrupt storm when RX FIFO overflows.
Disabling this interrupt has no side effect and eliminates
interrupt storms when the RX FIFO overflows.
Commit 8a7cb245cf28 ("net: stmmac: Do not enable RX FIFO
overflow interrupts") disables RX FIFO overflow interrupts
for DWMAC4 IP and removes the corresponding handling of
this interrupt. This patch is doing the same thing for
XGMAC IP.
Fixes: 2142754f8b9c ("net: stmmac: Add MAC related callbacks for XGMAC2")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250825-xgmac-minor-fixes-v3-1-c225fe4444c0@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The local Xoff value is being set before the firmware (FW) update.
In case of a failure where the FW is not updated with the new value,
there is no fallback to the previous value.
Update the local Xoff value after the FW has been successfully set.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-12-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Xon/Xoff sizes are derived from calculations that include
the port speed.
These settings need to be updated and applied whenever the
port speed is changed.
The port speed is typically set after the physical link goes down
and is negotiated as part of the link-up process between the two
connected interfaces.
Xon/Xoff parameters being updated at the point where the new
negotiated speed is established.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-11-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Xon/Xoff sizes are derived from calculation that include the MTU size.
Set Xon/Xoff when MTU is set.
If Xon/Xoff fails, set the previous MTU.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-10-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Changing flow steering modes is not allowed when eswitch is in switchdev
mode. This fix ensures that any steering mode change, including to
firmware steering, is correctly blocked while eswitch mode is switchdev.
Fixes: e890acd5ff18 ("net/mlx5: Add devlink flow_steering_mode parameter")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-9-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If PF (Physical Function) has SFs (Sub-Functions), since the SFs are not
taking part in the synchronization flow, sync reset can lead to fatal
error on the SFs, as the function will be closed unexpectedly from the
SF point of view.
Add a check to prevent sync reset when there are SFs on a PF device
which is not ECPF, as ECPF is teardowned gracefully before reset.
Fixes: 92501fa6e421 ("net/mlx5: Ack on sync_reset_request only if PF can do reset_now")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-8-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix lockdep assertion triggered during sync reset unload event. When the
sync reset flow is initiated using the devlink reload fw_activate
option, the PF already holds the devlink lock while handling unload
event. In this case, delegate sync reset unload event handling back to
the devlink callback process to avoid double-locking and resolve the
lockdep warning.
Kernel log:
WARNING: CPU: 9 PID: 1578 at devl_assert_locked+0x31/0x40
[...]
Call Trace:
<TASK>
mlx5_unload_one_devl_locked+0x2c/0xc0 [mlx5_core]
mlx5_sync_reset_unload_event+0xaf/0x2f0 [mlx5_core]
process_one_work+0x222/0x640
worker_thread+0x199/0x350
kthread+0x10b/0x230
? __pfx_worker_thread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x8e/0x100
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 7a9770f1bfea ("net/mlx5: Handle sync reset unload event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-7-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The devlink reload fw_activate command performs firmware activation
followed by driver reload, while devlink reload driver_reinit triggers
only driver reload. However, the driver reload logic differs between the
two modes, as on driver_reinit mode mlx5 also reloads auxiliary drivers,
while in fw_activate mode the auxiliary drivers are suspended where
applicable.
Additionally, following the cited commit, if the device has multiple PFs,
the behavior during fw_activate may vary between PFs: one PF may suspend
auxiliary drivers, while another reloads them.
Align devlink dev reload fw_activate behavior with devlink dev reload
driver_reinit, to reload all auxiliary drivers.
Fixes: 72ed5d5624af ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Akiva Goldberger <agoldberger@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In mlx5hws_pat_get_pattern(), when mlx5hws_pat_add_pattern_to_cache()
fails, the function attempts to clean up the pattern created by
mlx5hws_cmd_header_modify_pattern_create(). However, it incorrectly
uses *pattern_id which hasn't been set yet, instead of the local
ptrn_id variable that contains the actual pattern ID.
This results in attempting to destroy a pattern using uninitialized
data from the output parameter, rather than the valid pattern ID
returned by the firmware.
Use ptrn_id instead of *pattern_id in the cleanup path to properly
destroy the created pattern.
Fixes: aefc15a0fa1c ("net/mlx5: HWS, added modify header pattern and args handling")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In mlx5hws_pat_calc_nop(), src_field and dst_field are passed to
hws_action_modify_get_target_fields() which should set their values.
However, if an invalid action type is encountered, these variables
remain uninitialized and are later used to update prev_src_field
and prev_dst_field.
Initialize both variables to INVALID_FIELD to ensure they have
defined values in all code paths.
Fixes: 01e035fd0380 ("net/mlx5: HWS, handle modify header actions dependency")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When an invalid stc_type is provided, the function allocates memory for
shared_stc but jumps to unlock_and_out without freeing it, causing a
memory leak.
Fix by jumping to free_shared_stc label instead to ensure proper cleanup.
Fixes: 504e536d9010 ("net/mlx5: HWS, added actions handling")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the error path of hws_pool_buddy_init(), the buddy allocator cleanup
doesn't free the allocator structure itself, causing a memory leak.
Add the missing kfree() to properly release all allocated memory.
Fixes: c61afff94373 ("net/mlx5: HWS, added memory management handling")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-08-25 (ice, ixgbe)
For ice:
Emil adds a check to ensure auxiliary device was created before tear
down to prevent NULL a pointer dereference.
Jake reworks flow for failed Tx scheduler configuration to allow for
proper recovery and operation. He also adjusts ice_adapter index for
E825C devices as use of DSN is incompatible with this device.
Michal corrects tracking of buffer allocation failure in
ice_clean_rx_irq().
For ixgbe:
Jedrzej adds __packed attribute to ixgbe_orom_civd_info to compatibility
with device OROM data.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ixgbe: fix ixgbe_orom_civd_info struct layout
ice: fix incorrect counter for buffer allocation failures
ice: use fixed adapter index for E825C embedded devices
ice: don't leave device non-functional if Tx scheduler config fails
ice: fix NULL pointer dereference in ice_unplug_aux_dev() on reset
====================
Link: https://patch.msgid.link/20250825215019.3442873-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The HW resource reservation logic allows the L2 driver to use the
RoCE resources if the RoCE driver is not registered. When calculating
the stats contexts available for L2, we should not blindly subtract
the stats contexts reserved for RoCE unless the RoCE driver is
registered. This bug may cause the L2 rings to be less than the
number requested when we are close to running out of stats contexts.
Fixes: 2e4592dc9bee ("bnxt_en: Change MSIX/NQs allocation policy")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before we accept an ethtool request to increase a resource (such as
rings), we call the FW to check that the requested resource is likely
available first before we commit. But it is still possible that
the actual reservation or allocation can fail. The existing code
is missing the logic to adjust the TX rings in case the reserved
TX rings are less than requested. Add a warning message (a similar
message for RX rings already exists) and add the logic to adjust
the TX rings. Without this fix, the number of TX rings reported
to the stack can exceed the actual TX rings and ethtool -l will
report more than the actual TX rings.
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bnxt_set_dflt_rings() assumes that it is always called before any TC has
been created. So it doesn't take bp->num_tc into account and assumes
that it is always 0 or 1.
In the FW resource or capability change scenario, the FW will return
flags in bnxt_hwrm_if_change() that will cause the driver to
reinitialize and call bnxt_cancel_reservations(). This will lead to
bnxt_init_dflt_ring_mode() calling bnxt_set_dflt_rings() and bp->num_tc
may be greater than 1. This will cause bp->tx_ring[] to be sized too
small and cause memory corruption in bnxt_alloc_cp_rings().
Fix it by properly scaling the TX rings by bp->num_tc in the code
paths mentioned above. Add 2 helper functions to determine
bp->tx_nr_rings and bp->tx_nr_rings_per_tc.
Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
hw_stats now has only one variable for tx_octets/rx_octets, so we should
only increment p once, not twice. This would cause the statistics to be
reported under the wrong categories in `ethtool -S --all-groups` (which
uses hw_stats) but not `ethtool -S` (which uses ethtool_stats).
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Fixes: f6af690a295a ("net: cadence: macb: Report standard stats")
Link: https://patch.msgid.link/20250825172134.681861-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It looks like that every time when the interface was set down and up the
driver was creating a new ptp clock. On top of this the function
ptp_clock_unregister was never called.
Therefore fix this by calling ptp_clock_register and initialize the
mii_ts struct inside the probe function and call ptp_clock_unregister when
driver is removed.
Fixes: 7d272e63e0979d ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250825065543.2916334-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the following Telit Cinterion LE910C4-WWX new compositions:
0x1034: tty (AT) + tty (AT) + rmnet
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1034 Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=93f617e7
C: #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x1037: tty (diag) + tty (Telit custom) + tty (AT) + tty (AT) + rmnet
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 15 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1037 Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=93f617e7
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x1038: tty (Telit custom) + tty (AT) + tty (AT) + rmnet
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1038 Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=93f617e7
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Link: https://patch.msgid.link/20250822091324.39558-1-Fabio.Porcedda@telit.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
"Use after free" issue appears in suspend once race occurs when
napi poll scheduls after `netif_device_detach` and before napi disables.
For details, during suspend flow of virtio-net,
the tx queue state is set to "__QUEUE_STATE_DRV_XOFF" by CPU-A.
And at some coincidental times, if a TCP connection is still working,
CPU-B does `virtnet_poll` before napi disable.
In this flow, the state "__QUEUE_STATE_DRV_XOFF"
of tx queue will be cleared. This is not the normal process it expects.
After that, CPU-A continues to close driver then virtqueue is removed.
Sequence likes below:
--------------------------------------------------------------------------
CPU-A CPU-B
----- -----
suspend is called A TCP based on
virtio-net still work
virtnet_freeze
|- virtnet_freeze_down
| |- netif_device_detach
| | |- netif_tx_stop_all_queues
| | |- netif_tx_stop_queue
| | |- set_bit
| | (__QUEUE_STATE_DRV_XOFF,...)
| | softirq rasied
| | |- net_rx_action
| | |- napi_poll
| | |- virtnet_poll
| | |- virtnet_poll_cleantx
| | |- netif_tx_wake_queue
| | |- test_and_clear_bit
| | (__QUEUE_STATE_DRV_XOFF,...)
| |- virtnet_close
| |- virtnet_disable_queue_pair
| |- virtnet_napi_tx_disable
|- remove_vq_common
--------------------------------------------------------------------------
When TCP delayack timer is up, a cpu gets softirq and irq handler
`tcp_delack_timer_handler` will be called, which will finally call
`start_xmit` in virtio net driver.
Then the access to tx virtq will cause panic.
The root cause of this issue is that napi tx
is not disable before `netif_tx_stop_queue`,
once `virnet_poll` schedules in such coincidental time,
the tx queue state will be cleared.
To solve this issue, adjusts the order of
function `virtnet_close` in `virtnet_freeze_down`.
Co-developed-by: Ying Xu <ying123.xu@samsung.com>
Signed-off-by: Ying Xu <ying123.xu@samsung.com>
Signed-off-by: Junnan Wu <junnan01.wu@samsung.com>
Message-Id: <20250812090817.3463403-1-junnan01.wu@samsung.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
`McstFramesRcvdOk` counts the number of received multicast packets, and
it reports the value correctly.
However, reading `McstFramesRcvdOk` clears the register to zero. As a
result, the driver was reporting only the packets since the last read,
instead of the accumulated total.
Fix this by updating the multicast statistics accumulatively instaed of
instantaneously.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-on: D-Link DGE-550T Rev-A3
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250823182927.6063-3-yyyynoom@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before configuring the NIX block, the AF driver initiates the
"NIX block X2P bus calibration" and verifies that NIX interfaces
such as CGX and LBK are active and functioning correctly.
On few silicon variants(CNF10KA and CNF10KB), X2P calibration failures
have been observed on some CGX blocks that are not mapped to the NIX block.
Since both NIX-mapped and non-NIX-mapped CGX blocks share the same
VENDOR,DEVICE,SUBSYS_DEVID, it's not possible to skip probe based on
these parameters.
This patch introuduces "is_cgx_mapped_to_nix" API to detect and skip
probe of non NIX mapped CGX blocks.
Fixes: aba53d5dbcea ("octeontx2-af: NIX block admin queue init")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250822105805.2236528-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current layout of struct ixgbe_orom_civd_info causes incorrect data
storage due to compiler-inserted padding. This results in issues when
writing OROM data into the structure.
Add the __packed attribute to ensure the structure layout matches the
expected binary format without padding.
Fixes: 70db0788a262 ("ixgbe: read the OROM version information")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, the driver increments `alloc_page_failed` when buffer allocation fails
in `ice_clean_rx_irq()`. However, this counter is intended for page allocation
failures, not buffer allocation issues.
This patch corrects the counter by incrementing `alloc_buf_failed` instead,
ensuring accurate statistics reporting for buffer allocation failures.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Suggested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Priya Singh <priyax.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_adapter structure is used by the ice driver to connect multiple
physical functions of a device in software. It was introduced by
commit 0e2bddf9e5f9 ("ice: add ice_adapter for shared data across PFs on
the same NIC") and is primarily used for PTP support, as well as for
handling certain cross-PF synchronization.
The original design of ice_adapter used PCI address information to
determine which devices should be connected. This was extended to support
E825C devices by commit fdb7f54700b1 ("ice: Initial support for E825C
hardware in ice_adapter"), which used the device ID for E825C devices
instead of the PCI address.
Later, commit 0093cb194a75 ("ice: use DSN instead of PCI BDF for
ice_adapter index") replaced the use of Bus/Device/Function addressing with
use of the device serial number.
E825C devices may appear in "Dual NAC" configuration which has multiple
physical devices tied to the same clock source and which need to use the
same ice_adapter. Unfortunately, each "NAC" has its own NVM which has its
own unique Device Serial Number. Thus, use of the DSN for connecting
ice_adapter does not work properly. It "worked" in the pre-production
systems because the DSN was not initialized on the test NVMs and all the
NACs had the same zero'd serial number.
Since we cannot rely on the DSN, lets fall back to the logic in the
original E825C support which used the device ID. This is safe for E825C
only because of the embedded nature of the device. It isn't a discreet
adapter that can be plugged into an arbitrary system. All E825C devices on
a given system are connected to the same clock source and need to be
configured through the same PTP clock.
To make this separation clear, reserve bit 63 of the 64-bit index values as
a "fixed index" indicator. Always clear this bit when using the device
serial number as an index.
For E825C, use a fixed value defined as the 0x579C E825C backplane device
ID bitwise ORed with the fixed index indicator. This is slightly different
than the original logic of just using the device ID directly. Doing so
prevents a potential issue with systems where only one of the NACs is
connected with an external PHY over SGMII. In that case, one NAC would
have the E825C_SGMII device ID, but the other would not.
Separate the determination of the full 64-bit index from the 32-bit
reduction logic. Provide both ice_adapter_index() and a wrapping
ice_adapter_xa_index() which handles reducing the index to a long on 32-bit
systems. As before, cache the full index value in the adapter structure to
warn about collisions.
This fixes issues with E825C not initializing PTP on both NACs, due to
failure to connect the appropriate devices to the same ice_adapter.
Fixes: 0093cb194a75 ("ice: use DSN instead of PCI BDF for ice_adapter index")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_cfg_tx_topo function attempts to apply Tx scheduler topology
configuration based on NVM parameters, selecting either a 5 or 9 layer
topology.
As part of this flow, the driver acquires the "Global Configuration Lock",
which is a hardware resource associated with programming the DDP package
to the device. This "lock" is implemented by firmware as a way to
guarantee that only one PF can program the DDP for a device. Unlike a
traditional lock, once a PF has acquired this lock, no other PF will be
able to acquire it again (including that PF) until a CORER of the device.
Future requests to acquire the lock report that global configuration has
already completed.
The following flow is used to program the Tx topology:
* Read the DDP package for scheduler configuration data
* Acquire the global configuration lock
* Program Tx scheduler topology according to DDP package data
* Trigger a CORER which clears the global configuration lock
This is followed by the flow for programming the DDP package:
* Acquire the global configuration lock (again)
* Download the DDP package to the device
* Release the global configuration lock.
However, if configuration of the Tx topology fails, (i.e.
ice_get_set_tx_topo returns an error code), the driver exits
ice_cfg_tx_topo() immediately, and fails to trigger CORER.
While the global configuration lock is held, the firmware rejects most
AdminQ commands, as it is waiting for the DDP package download (or Tx
scheduler topology programming) to occur.
The current driver flows assume that the global configuration lock has been
reset by CORER after programming the Tx topology. Thus, the same PF
attempts to acquire the global lock again, and fails. This results in the
driver reporting "an unknown error occurred when loading the DDP package".
It then attempts to enter safe mode, but ultimately fails to finish
ice_probe() since nearly all AdminQ command report error codes, and the
driver stops loading the device at some point during its initialization.
The only currently known way that ice_get_set_tx_topo() can fail is with
certain older DDP packages which contain invalid topology configuration, on
firmware versions which strictly validate this data. The most recent
releases of the DDP have resolved the invalid data. However, it is still
poor practice to essentially brick the device, and prevent access to the
device even through safe mode or recovery mode. It is also plausible that
this command could fail for some other reason in the future.
We cannot simply release the global lock after a failed call to
ice_get_set_tx_topo(). Releasing the lock indicates to firmware that global
configuration (downloading of the DDP) has completed. Future attempts by
this or other PFs to load the DDP will fail with a report that the DDP
package has already been downloaded. Then, PFs will enter safe mode as they
realize that the package on the device does not meet the minimum version
requirement to load. The reported error messages are confusing, as they
indicate the version of the default "safe mode" package in the NVM, rather
than the version of the file loaded from /lib/firmware.
Instead, we need to trigger CORER to clear global configuration. This is
the lowest level of hardware reset which clears the global configuration
lock and related state. It also clears any already downloaded DDP.
Crucially, it does *not* clear the Tx scheduler topology configuration.
Refactor ice_cfg_tx_topo() to always trigger a CORER after acquiring the
global lock, regardless of success or failure of the topology
configuration.
We need to re-initialize the HW structure when we trigger the CORER. Thus,
it makes sense for this to be the responsibility of ice_cfg_tx_topo()
rather than its caller, ice_init_tx_topology(). This avoids needless
re-initialization in cases where we don't attempt to update the Tx
scheduler topology, such as if it has already been programmed.
There is one catch: failure to re-initialize the HW struct should stop
ice_probe(). If this function fails, we won't have a valid HW structure and
cannot ensure the device is functioning properly. To handle this, ensure
ice_cfg_tx_topo() returns a limited set of error codes. Set aside one
specifically, -ENODEV, to indicate that the ice_init_tx_topology() should
fail and stop probe.
Other error codes indicate failure to apply the Tx scheduler topology. This
is treated as a non-fatal error, with an informational message informing
the system administrator that the updated Tx topology did not apply. This
allows the device to load and function with the default Tx scheduler
topology, rather than failing to load entirely.
Note that this use of CORER will not result in loops with future PFs
attempting to also load the invalid Tx topology configuration. The first PF
will acquire the global configuration lock as part of programming the DDP.
Each PF after this will attempt to acquire the global lock as part of
programming the Tx topology, and will fail with the indication from
firmware that global configuration is already complete. Tx scheduler
topology configuration is only performed during driver init (probe or
devlink reload) and not during cleanup for a CORER that happens after probe
completes.
Fixes: 91427e6d9030 ("ice: Support 5 layer topology")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Issuing a reset when the driver is loaded without RDMA support, will
results in a crash as it attempts to remove RDMA's non-existent auxbus
device:
echo 1 > /sys/class/net/<if>/device/reset
BUG: kernel NULL pointer dereference, address: 0000000000000008
...
RIP: 0010:ice_unplug_aux_dev+0x29/0x70 [ice]
...
Call Trace:
<TASK>
ice_prepare_for_reset+0x77/0x260 [ice]
pci_dev_save_and_disable+0x2c/0x70
pci_reset_function+0x88/0x130
reset_store+0x5a/0xa0
kernfs_fop_write_iter+0x15e/0x210
vfs_write+0x273/0x520
ksys_write+0x6b/0xe0
do_syscall_64+0x79/0x3b0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
ice_unplug_aux_dev() checks pf->cdev_info->adev for NULL pointer, but
pf->cdev_info will also be NULL, leading to the deref in the trace above.
Introduce a flag to be set when the creation of the auxbus device is
successful, to avoid multiple NULL pointer checks in ice_unplug_aux_dev().
Fixes: c24a65b6a27c7 ("iidc/ice/irdma: Update IDC to support multiple consumers")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
idpf: replace Tx flow scheduling buffer ring with buffer pool
Joshua Hay says:
This series fixes a stability issue in the flow scheduling Tx send/clean
path that results in a Tx timeout.
The existing guardrails in the Tx path were not sufficient to prevent
the driver from reusing completion tags that were still in flight (held
by the HW). This collision would cause the driver to erroneously clean
the wrong packet thus leaving the descriptor ring in a bad state.
The main point of this fix is to replace the flow scheduling buffer ring
with a large pool/array of buffers. The completion tag then simply is
the index into this array. The driver tracks the free tags and pulls
the next free one from a refillq. The cleaning routines simply use the
completion tag from the completion descriptor to index into the array to
quickly find the buffers to clean.
All of the code to support this is added first to ensure traffic still
passes with each patch. The final patch then removes all of the
obsolete stashing code.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: remove obsolete stashing code
idpf: stop Tx if there are insufficient buffer resources
idpf: replace flow scheduling buffer ring with buffer pool
idpf: simplify and fix splitq Tx packet rollback error path
idpf: improve when to set RE bit logic
idpf: add support for Tx refillqs in flow scheduling mode
====================
Link: https://patch.msgid.link/20250821180100.401955-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Once driver submits the packets to the hardware, each packet
traverse through multiple transmit levels in the following
order:
SMQ -> TL4 -> TL3 -> TL2 -> TL1
The SMQ supports configurable minimum and maximum packet sizes.
It enters to a hang state, if driver submits packets with
out of bound lengths.
To avoid the same, implement packet length validation before
submitting packets to the hardware. Increment tx_dropped counter
on failure.
Fixes: 3184fb5ba96e ("octeontx2-vf: Virtual function driver support")
Fixes: 22f858796758 ("octeontx2-pf: Add basic net_device_ops")
Fixes: 3ca6c4c882a7 ("octeontx2-pf: Add packet transmission support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250821062528.1697992-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When removing a macb device, the driver calls phy_exit() before
unregister_netdev(). This leads to a WARN from kernfs:
------------[ cut here ]------------
kernfs: can not remove 'attached_dev', no directory
WARNING: CPU: 1 PID: 27146 at fs/kernfs/dir.c:1683
Call trace:
kernfs_remove_by_name_ns+0xd8/0xf0
sysfs_remove_link+0x24/0x58
phy_detach+0x5c/0x168
phy_disconnect+0x4c/0x70
phylink_disconnect_phy+0x6c/0xc0 [phylink]
macb_close+0x6c/0x170 [macb]
...
macb_remove+0x60/0x168 [macb]
platform_remove+0x5c/0x80
...
The warning happens because the PHY is being exited while the netdev
is still registered. The correct order is to unregister the netdev
before shutting down the PHY and cleaning up the MDIO bus.
Fix this by moving unregister_netdev() ahead of phy_exit() in
macb_remove().
Fixes: 8b73fa3ae02b ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: luoguangfei <15388634752@163.com>
Link: https://patch.msgid.link/20250818232527.1316-1-15388634752@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With the new Tx buffer management scheme, there is no need for all of
the stashing mechanisms, the hash table, the reserve buffer stack, etc.
Remove all of that.
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The Tx refillq logic will cause packets to be silently dropped if there
are not enough buffer resources available to send a packet in flow
scheduling mode. Instead, determine how many buffers are needed along
with number of descriptors. Make sure there are enough of both resources
to send the packet, and stop the queue if not.
Fixes: 7292af042bcf ("idpf: fix a race in txq wakeup")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Replace the TxQ buffer ring with one large pool/array of buffers (only
for flow scheduling). This eliminates the tag generation and makes it
impossible for a tag to be associated with more than one packet.
The completion tag passed to HW through the descriptor is the index into
the array. That same completion tag is posted back to the driver in the
completion descriptor, and used to index into the array to quickly
retrieve the buffer during cleaning. In this way, the tags are treated
as a fix sized resource. If all tags are in use, no more packets can be
sent on that particular queue (until some are freed up). The tag pool
size is 64K since the completion tag width is 16 bits.
For each packet, the driver pulls a free tag from the refillq to get the
next free buffer index. When cleaning is complete, the tag is posted
back to the refillq. A multi-frag packet spans multiple buffers in the
driver, therefore it uses multiple buffer indexes/tags from the pool.
Each frag pulls from the refillq to get the next free buffer index.
These are tracked in a next_buf field that replaces the completion tag
field in the buffer struct. This chains the buffers together so that the
packet can be cleaned from the starting completion tag taken from the
completion descriptor, then from the next_buf field for each subsequent
buffer.
In case of a dma_mapping_error occurs or the refillq runs out of free
buf_ids, the packet will execute the rollback error path. This unmaps
any buffers previously mapped for the packet. Since several free
buf_ids could have already been pulled from the refillq, we need to
restore its original state as well. Otherwise, the buf_ids/tags
will be leaked and not used again until the queue is reallocated.
Descriptor completions only advance the descriptor ring index to "clean"
the descriptors. The packet completions only clean the buffers
associated with the given packet completion tag and do not update the
descriptor ring index.
When operating in queue based scheduling mode, the array still acts as a
ring and will only have TxQ descriptor count entries. The tx_bufs are
still associated 1:1 with the descriptor ring entries and we can use the
conventional indexing mechanisms.
Fixes: c2d548cad150 ("idpf: add TX splitq napi poll support")
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Move (and rename) the existing rollback logic to singleq.c since that
will be the only consumer. Create a simplified splitq specific rollback
function to loop through and unmap tx_bufs based on the completion tag.
This is critical before replacing the Tx buffer ring with the buffer
pool since the previous rollback indexing will not work to unmap the
chained buffers from the pool.
Cache the next_to_use index before any portion of the packet is put on
the descriptor ring. In case of an error, the rollback will bump tail to
the correct next_to_use value. Because the splitq path now supports
different types of context descriptors (and potentially multiple in the
future), this will take care of rolling back any and all context
descriptors encoded on the ring for the erroneous packet. The previous
rollback logic was broken for PTP packets since it would not account for
the PTP context descriptor.
Fixes: 1a49cf814fe1 ("idpf: add Tx timestamp flows")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Track the gap between next_to_use and the last RE index. Set RE again
if the gap is large enough to ensure RE bit is set frequently. This is
critical before removing the stashing mechanisms because the
opportunistic descriptor ring cleaning from the out-of-order completions
will go away. Previously the descriptors would be "cleaned" by both the
descriptor (RE) completion and the out-of-order completions. Without the
latter, we must ensure the RE bit is set more frequently. Otherwise,
it's theoretically possible for the descriptor ring next_to_clean to
never advance. The previous implementation was dependent on the start
of a packet falling on a 64th index in the descriptor ring, which is not
guaranteed with large packets.
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In certain production environments, it is possible for completion tags
to collide, meaning N packets with the same completion tag are in flight
at the same time. In this environment, any given Tx queue is effectively
used to send both slower traffic and higher throughput traffic
simultaneously. This is the result of a customer's specific
configuration in the device pipeline, the details of which Intel cannot
provide. This configuration results in a small number of out-of-order
completions, i.e., a small number of packets in flight. The existing
guardrails in the driver only protect against a large number of packets
in flight. The slower flow completions are delayed which causes the
out-of-order completions. The fast flow will continue sending traffic
and generating tags. Because tags are generated on the fly, the fast
flow eventually uses the same tag for a packet that is still in flight
from the slower flow. The driver has no idea which packet it should
clean when it processes the completion with that tag, but it will look
for the packet on the buffer ring before the hash table. If the slower
flow packet completion is processed first, it will end up cleaning the
fast flow packet on the ring prematurely. This leaves the descriptor
ring in a bad state resulting in a crash or Tx timeout.
In summary, generating a tag when a packet is sent can lead to the same
tag being associated with multiple packets. This can lead to resource
leaks, crashes, and/or Tx timeouts.
Before we can replace the tag generation, we need a new mechanism for
the send path to know what tag to use next. The driver will allocate and
initialize a refillq for each TxQ with all of the possible free tag
values. During send, the driver grabs the next free tag from the refillq
from next_to_clean. While cleaning the packet, the clean routine posts
the tag back to the refillq's next_to_use to indicate that it is now
free to use.
This mechanism works exactly the same way as the existing Rx refill
queues, which post the cleaned buffer IDs back to the buffer queue to be
reposted to HW. Since we're using the refillqs for both Rx and Tx now,
genericize some of the existing refillq support.
Note: the refillqs will not be used yet. This is only demonstrating how
they will be used to pass free tags back to the send path.
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When port buffer headroom changes, port_update_shared_buffer()
recalculates the shared buffer size and splits it in a 3:1 ratio
(lossy:lossless) - Currently, the calculation is:
lossless = shared / 4;
lossy = (shared / 4) * 3;
Meaning, the calculation dropped the remainder of shared % 4 due to
integer division, unintentionally reducing the total shared buffer
by up to three cells on each update. Over time, this could shrink
the buffer below usable size.
Fix it by changing the calculation to:
lossless = shared / 4;
lossy = shared - lossless;
This retains all buffer cells while still approximating the
intended 3:1 split, preventing capacity loss over time.
While at it, perform headroom calculations in units of cells rather than
in bytes for more accurate calculations avoiding extra divisions.
Fixes: a440030d8946 ("net/mlx5e: Update shared buffer along with device buffer changes")
Signed-off-by: Armen Ratner <armeng@nvidia.com>
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20250820133209.389065-9-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SW currently saves local buffer ownership when setting
the buffer.
This means that the SW assumes it has ownership of the buffer
after the command is set.
If setting the buffer fails and we remain in FW ownership,
the local buffer ownership state incorrectly remains as SW-owned.
This leads to incorrect behavior in subsequent PFC commands,
causing failures.
Instead of saving local buffer ownership in SW,
query the FW for buffer ownership when setting the buffer.
This ensures that the buffer ownership state is accurately
reflected, avoiding the issues caused by incorrect ownership
states.
Fixes: ecdf2dadee8e ("net/mlx5e: Receive buffer support for DCBX")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-8-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Restore the __esw_qos_free_node() call removed by the offending commit.
Fixes: 97733d1e00a0 ("net/mlx5: Add traffic class scheduling support for vport QoS")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-7-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing esw_qos_put() call when __esw_qos_alloc_node() fails in
mlx5_esw_qos_vport_enable().
Fixes: be034baba83e ("net/mlx5: Make vport QoS enablement more flexible for future extensions")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a VF has been configured and the user later clears all QoS settings,
the vport element remains in the firmware QoS tree. This leads to
inconsistent behavior compared to VFs that were never configured, since
the FW assumes that unconfigured VFs are outside the QoS hierarchy.
As a result, the bandwidth share across VFs may differ, even though
none of them appear to have any configuration.
Align the driver behavior with the FW expectation by destroying the
vport QoS element when all configurations are removed.
Fixes: c9497c98901c ("net/mlx5: Add support for setting VF min rate")
Fixes: cf7e73770d1b ("net/mlx5: Manage TC arbiter nodes and implement full support for tc-bw")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20250820133209.389065-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When changing parent of a node/leaf with tc-bw configured, the code
saves and restores tc-bw values. However, it was reading the converted
hardware bw_share values (where 0 becomes 1) instead of the original
user values, causing incorrect tc-bw calculations after parent change.
Store original tc-bw values in the node structure and use them directly
for save/restore operations.
Fixes: cf7e73770d1b ("net/mlx5: Manage TC arbiter nodes and implement full support for tc-bw")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the driver creates a default group (`node0`) and attaches
all vports to it unless the user explicitly sets a parent group. As a
result, when a user configures tx_share on a group and tx_share on
a VF, the expectation is for the group and the VF to share bandwidth
relatively. However, since the VF is not connected to the same parent
(but to the default node), the proportional share logic is not applied
correctly.
To fix this, remove the default group (`node0`) and instead connect
vports directly to the root TSAR when no parent is specified. This
ensures that vports and groups share the same root scheduler and their
tx_share values are compared directly under the same hierarchy.
Fixes: 0fe132eac38c ("net/mlx5: E-switch, Allow to add vports to rate groups")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
