| Age | Commit message (Collapse) | Author |
|---|
|
Correct spelling of platforms, various, and initial.
As flagged by codespell.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As it's name suggests, parse_eeprom() parses EEPROM data.
This is done by reading data, 16 bits at a time as follows:
for (i = 0; i < 128; i++)
((__le16 *) sromdata)[i] = cpu_to_le16(read_eeprom(np, i));
sromdata is at the same memory location as psrom.
And the type of psrom is a pointer to struct t_SROM.
As can be seen in the loop above, data is stored in sromdata, and thus
psrom, as 16-bit little-endian values. However, the integer fields of
t_SROM are host byte order.
In the case of the led_mode field this results in a but which has been
addressed by commit e7e5ae71831c ("net: dlink: Correct endianness
handling of led_mode").
In the case of the remaining fields, which are updated by this patch,
I do not believe this does not result in any bugs. But it does seem
best to correctly annotate the endianness of integers.
Flagged by Sparse as:
.../dl2k.c:344:35: warning: restricted __le32 degrades to integer
Compile tested only.
No run-time change intended.
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AF driver assigns reserved MCAM entries (for unicast, broadcast,
etc.) based on the NIXLF number. When a NIXLF is detached, these entries
are disabled.
For example,
PF NIXLF
--------------------
PF0 0
SDP-VF0 1
If the user unbinds both PF0 and SDP-VF0 interfaces and then binds them in
reverse order
PF NIXLF
---------------------
SDP-VF0 0
PF0 1
In this scenario, the PF0 unicast entry is getting corrupted because
the MCAM entry contains stale data (SDP-VF0 ucast data)
This patch resolves the issue by clearing the unicast MCAM entry during
NIXLF detach
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PCI_PWRCTRL_PWRSEQ and HAVE_PWRCTRL symbols have been renamed to
reflect the pwrctrl framework name. Switch to the non-deprecated symbols.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Johnson <jjohnson@kernel.org> # drivers/net/wireless/ath/...
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250402132634.18065-4-johan+linaro@kernel.org
|
|
The PCI_PWRCTRL_PWRSEQ and HAVE_PWRCTRL symbols have been renamed to
reflect the pwrctrl framework name. Switch to the non-deprecated symbols.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Johnson <jjohnson@kernel.org> # drivers/net/wireless/ath/...
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250402132634.18065-3-johan+linaro@kernel.org
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Lots of new things, notably:
* ath12k: monitor mode for WCN7850, better 6 GHz regulatory
* brcmfmac: SAE for some Cypress devices
* iwlwifi: rework device configuration
* mac80211: scan improvements with MLO
* mt76: EHT improvements, new device IDs
* rtw88: throughput improvements
* rtw89: MLO, STA/P2P concurrency improvements, SAR
* tag 'wireless-next-2025-05-22' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (389 commits)
wifi: mt76: mt7925: add rfkill_poll for hardware rfkill
wifi: mt76: support power delta calculation for 5 TX paths
wifi: mt76: fix available_antennas setting
wifi: mt76: mt7996: fix RX buffer size of MCU event
wifi: mt76: mt7996: change max beacon size
wifi: mt76: mt7996: fix invalid NSS setting when TX path differs from NSS
wifi: mt76: mt7996: drop fragments with multicast or broadcast RA
wifi: mt76: mt7996: set EHT max ampdu length capability
wifi: mt76: mt7996: fix beamformee SS field
wifi: mt76: remove capability of partial bandwidth UL MU-MIMO
wifi: mt76: mt7925: add test mode support
wifi: mt76: mt7925: extend MCU support for testmode
wifi: mt76: mt7925: ensure all MCU commands wait for response
wifi: mt76: mt7925: refine the sniffer commnad
wifi: mt76: mt7925: prevent multiple scan commands
wifi: mt76: mt7915: Fix null-ptr-deref in mt7915_mmio_wed_init()
wifi: mt76: mt7996: Fix null-ptr-deref in mt7996_mmio_wed_init()
wifi: mt76: mt7925: add RNR scan support for 6GHz
wifi: mt76: add mt76_connac_mcu_build_rnr_scan_param routine
wifi: mt76: scan: Fix 'mlink' dereferenced before IS_ERR_OR_NULL check
...
====================
Link: https://patch.msgid.link/20250522165501.189958-50-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.15-rc8).
Conflicts:
80f2ab46c2ee ("irdma: free iwdev->rf after removing MSI-X")
4bcc063939a5 ("ice, irdma: fix an off by one in error handling code")
c24a65b6a27c ("iidc/ice/irdma: Update IDC to support multiple consumers")
https://lore.kernel.org/20250513130630.280ee6c5@canb.auug.org.au
No extra adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch convert mlx5 to use the new netdev instance lock in addition
to the pre-existing state_lock (and the RTNL).
mlx5e_priv.state_lock was already used throughout mlx5 to protect
against concurrent state modifications on the same netdev, usually in
addition to the RTNL. The new netdev instance lock will eventually
replace it, but for now, it is acquired in addition to the existing
locks in the order RTNL -> instance lock -> state_lock.
All three netdev types handled by mlx5 are converted to the new style of
locking, because they share a lot of code related to initializing
channels and dealing with NAPI, so it's better to convert all three
rather than introduce different assumptions deep in the call stack
depending on the type of device.
Because of the nature of the call graphs in mlx5, it wasn't possible to
incrementally convert parts of the driver to use the new lock, since
either all call paths into NAPI have to possess the new lock if the
*_locked variants are used, or none of them can have the lock.
One area which required extra care is the interaction between closing
channels and devlink health reporter tasks.
Previously, the recovery tasks were unconditionally acquiring the
RTNL, which could lead to deadlocks in these scenarios:
T1: mlx5e_close (== .ndo_stop(), has RTNL) -> mlx5e_close_locked
-> mlx5e_close_channels -> mlx5e_ptp_close
-> mlx5e_ptp_close_queues -> mlx5e_ptp_close_txqsqs
-> mlx5e_ptp_close_txqsq
-> cancel_work_sync(&ptpsq->report_unhealthy_work) waits for
T2: mlx5e_ptpsq_unhealthy_work -> mlx5e_reporter_tx_ptpsq_unhealthy
-> mlx5e_health_report -> devlink_health_report
-> devlink_health_reporter_recover
-> mlx5e_tx_reporter_ptpsq_unhealthy_recover which does:
rtnl_lock(); => Deadlock.
Another similar instance of this is:
T1: mlx5e_close (== .ndo_stop(), has RTNL) -> mlx5e_close_locked
-> mlx5e_close_channels -> mlx5e_ptp_close
-> mlx5e_ptp_close_queues -> mlx5e_ptp_close_txqsqs
-> mlx5e_ptp_close_txqsq
-> cancel_work_sync(&sq->recover_work) waits for
T2: mlx5e_tx_err_cqe_work -> mlx5e_reporter_tx_err_cqe
-> mlx5e_health_report -> devlink_health_report
-> devlink_health_reporter_recover
-> mlx5e_tx_reporter_err_cqe_recover which does:
rtnl_lock(); => Another deadlock.
Fix that by using the same pattern previously done in
mlx5e_tx_timeout_work, where the RTNL was repeatedly tried to be
acquired until either:
a) it is successfully acquired or
b) there's no need for the work to be done any more (channel is being
closed).
Now, for all three recovery tasks, the instance lock is repeatedly tried
to be acquired until successful or the channel/SQ is closed.
As a side-effect, drop the !test_bit(MLX5E_STATE_OPENED, &priv->state)
check from mlx5e_tx_timeout_work, it's weaker than
!test_bit(MLX5E_STATE_CHANNELS_ACTIVE, &priv->state) and unnecessary.
Future patches will introduce new call paths (from netdev queue
management ops) which can close channels (and call cancel_work_sync on
the recovery tasks) without the RTNL lock and only with the netdev
instance lock.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1747829342-1018757-6-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's no explanation in the original commit of why that was done, but
presumably flashing takes a long time and holding RTNL for so long
blocks other interactions with the netdev layer.
However, the stack is moving towards netdev instance locking and
dropping and reacquiring RTNL in the context of flashing introduces
locking ordering issues: RTNL must be acquired before the netdev
instance lock and released after it.
This patch therefore takes the simpler approach by no longer dropping
and reacquiring the RTNL, as soon RTNL for ethtool will be removed,
leaving only the instance lock to protect against races.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1747829342-1018757-5-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When xdp is attached or detached, dev->ndo_bpf() is called by
do_setlink(), and it acquires netdev_lock() if needed.
Unlike other drivers, the bnxt driver is protected by netdev_lock while
xdp is attached/detached because it sets dev->request_ops_lock to true.
So, the bnxt_xdp(), that is callback of ->ndo_bpf should not acquire
netdev_lock().
But the xdp_features_{set | clear}_redirect_target() was changed to
acquire netdev_lock() internally.
It causes a deadlock.
To fix this problem, bnxt driver should use
xdp_features_{set | clear}_redirect_target_locked() instead.
Splat looks like:
============================================
WARNING: possible recursive locking detected
6.15.0-rc6+ #1 Not tainted
--------------------------------------------
bpftool/1745 is trying to acquire lock:
ffff888131b85038 (&dev->lock){+.+.}-{4:4}, at: xdp_features_set_redirect_target+0x1f/0x80
but task is already holding lock:
ffff888131b85038 (&dev->lock){+.+.}-{4:4}, at: do_setlink.constprop.0+0x24e/0x35d0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&dev->lock);
lock(&dev->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by bpftool/1745:
#0: ffffffffa56131c8 (rtnl_mutex){+.+.}-{4:4}, at: rtnl_setlink+0x1fe/0x570
#1: ffffffffaafa75a0 (&net->rtnl_mutex){+.+.}-{4:4}, at: rtnl_setlink+0x236/0x570
#2: ffff888131b85038 (&dev->lock){+.+.}-{4:4}, at: do_setlink.constprop.0+0x24e/0x35d0
stack backtrace:
CPU: 1 UID: 0 PID: 1745 Comm: bpftool Not tainted 6.15.0-rc6+ #1 PREEMPT(undef)
Hardware name: ASUS System Product Name/PRIME Z690-P D4, BIOS 0603 11/01/2021
Call Trace:
<TASK>
dump_stack_lvl+0x7a/0xd0
print_deadlock_bug+0x294/0x3d0
__lock_acquire+0x153b/0x28f0
lock_acquire+0x184/0x340
? xdp_features_set_redirect_target+0x1f/0x80
__mutex_lock+0x1ac/0x18a0
? xdp_features_set_redirect_target+0x1f/0x80
? xdp_features_set_redirect_target+0x1f/0x80
? __pfx_bnxt_rx_page_skb+0x10/0x10 [bnxt_en
? __pfx___mutex_lock+0x10/0x10
? __pfx_netdev_update_features+0x10/0x10
? bnxt_set_rx_skb_mode+0x284/0x540 [bnxt_en
? __pfx_bnxt_set_rx_skb_mode+0x10/0x10 [bnxt_en
? xdp_features_set_redirect_target+0x1f/0x80
xdp_features_set_redirect_target+0x1f/0x80
bnxt_xdp+0x34e/0x730 [bnxt_en 11cbcce8fa11cff1dddd7ef358d6219e4ca9add3]
dev_xdp_install+0x3f4/0x830
? __pfx_bnxt_xdp+0x10/0x10 [bnxt_en 11cbcce8fa11cff1dddd7ef358d6219e4ca9add3]
? __pfx_dev_xdp_install+0x10/0x10
dev_xdp_attach+0x560/0xf70
dev_change_xdp_fd+0x22d/0x280
do_setlink.constprop.0+0x2989/0x35d0
? __pfx_do_setlink.constprop.0+0x10/0x10
? lock_acquire+0x184/0x340
? find_held_lock+0x32/0x90
? rtnl_setlink+0x236/0x570
? rcu_is_watching+0x11/0xb0
? trace_contention_end+0xdc/0x120
? __mutex_lock+0x946/0x18a0
? __pfx___mutex_lock+0x10/0x10
? __lock_acquire+0xa95/0x28f0
? rcu_is_watching+0x11/0xb0
? rcu_is_watching+0x11/0xb0
? cap_capable+0x172/0x350
rtnl_setlink+0x2cd/0x570
Fixes: 03df156dd3a6 ("xdp: double protect netdev->xdp_flags with netdev->lock")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250520071155.2462843-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Felix Fietkau says:
===================
mt76 patches for 6.16
- fixes
- EHT improvements
- new device ids
===================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v6.16
ath12k:
Add monitor mode support for WCN7850.
Enhance regulatory support including 6 GHz power modes.
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add mac80211 rfkill_poll ops to monitor hardware rfkill state
and state change will be updated.
Signed-off-by: Allan Wang <allan.wang@mediatek.com>
Link: https://patch.msgid.link/20250507053131.4173691-1-allan.wang@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
One variant of MT7992 has 5 TX paths, so extend the power delta function
to support it. Also, rename nss_delta to path_delta since the value is
based on the number of TX paths rather tha the number of spatial streams.
(path delta [0.5 dBm] = 10 * log(path number) [dBm] * 2)
Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-9-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Check if available_antennas_tx and available_antennas_rx are already set
during the per-chip initialization phase; otherwise, they could be
overwritten with incorrect values.
Fixes: 69d54ce7491d ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-8-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Some management frames are first processed by the firmware and then
passed to the driver through the MCU event rings. In CONNAC3, event rings
do not support scatter-gather and have a size limitation of 2048 bytes.
If a packet sized between 1728 and 2048 bytes arrives from an event ring,
the ring will hang because the driver attempts to use scatter-gather to
process it.
To fix this, include the size of struct skb_shared_info in the MCU RX
buffer size to prevent scatter-gather from being used for event skb in
mt76_dma_rx_fill_buf().
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Co-developed-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-7-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
According to hardware capability, the maximum beacon size is 2048 bytes
minus the size of TLV headers.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-6-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The maximum TX path and NSS may differ on a band. For example, one variant
of the MT7992 has 5 TX paths and 4 NSS on the 5 GHz band. To address this,
add orig_antenna_mask to record the maximum NSS and prevent setting an
invalid NSS in mt7996_set_antenna().
Fixes: 69d54ce7491d ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-5-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
IEEE 802.11 fragmentation can only be applied to unicast frames.
Therefore, drop fragments with multicast or broadcast RA. This patch
addresses vulnerabilities such as CVE-2020-26145.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-4-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Set the max AMPDU length in the EHT MAC CAP. Without this patch, the
peer station cannot obtain the correct capability, which prevents
achieving peak throughput on the 2 GHz band.
Fixes: 1816ad9381e0 ("wifi: mt76: mt7996: add max mpdu len capability")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-3-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix the beamformee SS field for the mt7996, mt7992 and mt7990 chipsets.
For the mt7992, this value shall be set to 0x4, while the others shall
be set to 0x3.
Fixes: 5b20557593d4 ("wifi: mt76: connac: adjust phy capabilities based on band constraints")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-2-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The firmware only supports full bandwidth UL MU-MIMO, so remove the
partial bandwidth capability from HE PHY CAP.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250515032952.1653494-1-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The test mode interface allows controlled execution of chip-level
operations such as continuous transmission, reception tests, and
register access, which are essential during bring-up, diagnostics,
and factory testing.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Link: https://patch.msgid.link/20250505233618.1951021-2-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add MCU command and its handling needed for testmode support on
MT7925. This enables low-level chip testing features such as
continuous TX/RX..
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Link: https://patch.msgid.link/20250505233618.1951021-1-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Modify MCU command sending functions to wait for a response,
ensuring consistent behavior across all commands and improves
reliability by confirming that each command is processed
successfully.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250414013954.1151774-3-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Remove a duplicate call to `mt76_mcu_send_msg` to fix redundant operations
in the sniffer command handling.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250414013954.1151774-2-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add a check to ensure only one scan command is active at a time
by testing the MT76_HW_SCANNING state.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250414013954.1151774-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
devm_ioremap() returns NULL on error. Currently, mt7915_mmio_wed_init()
does not check for this case, which results in a NULL pointer
dereference.
Prevent null pointer dereference in mt7915_mmio_wed_init().
Fixes: 4f831d18d12d ("wifi: mt76: mt7915: enable WED RX support")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Link: https://patch.msgid.link/20250407061900.85317-1-bsdhenrymartin@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
devm_ioremap() returns NULL on error. Currently, mt7996_mmio_wed_init()
does not check for this case, which results in a NULL pointer
dereference.
Prevent null pointer dereference in mt7996_mmio_wed_init()
Fixes: 83eafc9251d6 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Link: https://patch.msgid.link/20250407032349.83360-1-bsdhenrymartin@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Enhance the mt7925 to include RNR scan support. It adds
the necessary RNR information to the scan command.
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250321013829.3598-2-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Introduce mt76_connac_mcu_build_rnr_scan_param routine for handling
RNR scan. This is a preliminary patch to enable RNR scan in mt7921 and
mt7925 driver.
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250321013829.3598-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202504011739.HvUKtUUe-lkp@intel.com/
Fixes: 3ba20af886d1 ("wifi: mt76: scan: set vif offchannel link for scanning/roc")
Signed-off-by: Feng Jiang <jiangfeng@kylinos.cn>
Link: https://patch.msgid.link/20250402062415.25434-1-jiangfeng@kylinos.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2025-05-22
this is a pull request of 4 patches for net/main.
The first 3 patches are by Axel Forsman and fix a ISR race condition
in the kvaser_pciefd driver.
The last patch is by Carlos Sanchez and fixes the reception of short
error messages in the slcan driver.
* tag 'linux-can-fixes-for-6.15-20250521' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: slcan: allow reception of short error messages
can: kvaser_pciefd: Continue parsing DMA buf after dropped RX
can: kvaser_pciefd: Fix echo_skb race
can: kvaser_pciefd: Force IRQ edge in case of nested IRQ
====================
Link: https://patch.msgid.link/20250522082344.490913-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The current implementation maps the APR table using a fixed size,
which can lead to incorrect mapping when the number of PFs and VFs
varies.
This patch corrects the mapping by calculating the APR table
size dynamically based on the values configured in the
APR_LMT_CFG register, ensuring accurate representation
of APR entries in debugfs.
Fixes: 0daa55d033b0 ("octeontx2-af: cn10k: debugfs for dumping LMTST map table").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Link: https://patch.msgid.link/20250521060834.19780-3-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch enables the LMT line for a PF/VF by setting the
LMT_ENA bit in the APR_LMT_MAP_ENTRY_S structure.
Additionally, it simplifies the logic for calculating the
LMTST table index by consistently using the maximum
number of hw supported VFs (i.e., 256).
Fixes: 873a1e3d207a ("octeontx2-af: cn10k: Setting up lmtst map table").
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250521060834.19780-2-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Priority flow control is not supported for LBK and SDP vf. This patch
adds support to not add dcbnl_ops for LBK and SDP vf.
Fixes: 8e67558177f8 ("octeontx2-pf: PFC config support with DCBx")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250519072658.2960851-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Having adjacent accelerated modify header actions (so-called
pattern-argument actions) may result in inconsistent outcome.
These inconsistencies can take the form of writes to the same
field or a read coupled with a write to the same field. The
solution is to detect such dependencies and insert nops between
the offending actions.
The existing implementation had a few issues, which pretty much
required a complete rewrite of the code that handles these
dependencies.
In the new implementation we're doing the following:
* Checking any two adjacent actions for conflicts (not just
odd-even pairs).
* Marking 'set' and 'add' action fields as destination, rather
than source, for the purposes of checking for conflicts.
* Checking all types of actions ('add', 'set', 'copy') for
dependencies.
* Managing offsets of the args in the buffer - copy the action
args to the right place in the buffer.
* Checking that after inserting nops we're still within the number
of supported actions - return an error otherwise.
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1747766802-958178-5-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix typo - rename 'nope_locations' to 'nop_locations', which describes
the locations of 'nop' actions. To shorten the lines, this renaming
also required some refactoring.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1747766802-958178-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Hardware steering handles actions differently from firmware, but for
termination rules that use encapsulation the firmware needs to be aware
of the action.
Fix this by registering reformat actions with the firmware the first
time this is needed. To do this, add a third possible owner for an
action, and also a lock to protect against registration of the same
action from different threads.
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1747766802-958178-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The firmware reformat id is a u32 and can't safely be returned as an
int. Because the functions also need a way to signal error, prefer to
return the id as an output parameter and keep the return code only for
success/error.
While we're at it, also extract some duplicate code to fetch the
reformat id from a more generic struct pkt_reformat.
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1747766802-958178-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
idpf_vport_splitq_napi_poll() can incorrectly return @budget
after napi_complete_done() has been called.
This violates NAPI rules, because after napi_complete_done(),
current thread lost napi ownership.
Move the test against POLL_MODE before the napi_complete_done().
Fixes: c2d548cad150 ("idpf: add TX splitq napi poll support")
Reported-by: Peter Newman <peternewman@google.com>
Closes: https://lore.kernel.org/netdev/20250520121908.1805732-1-edumazet@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Joshua Hay <joshua.a.hay@intel.com>
Cc: Alan Brady <alan.brady@intel.com>
Cc: Madhu Chittim <madhu.chittim@intel.com>
Cc: Phani Burra <phani.r.burra@intel.com>
Cc: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Link: https://patch.msgid.link/20250520124030.1983936-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enic started using netif_get_num_default_rss_queues() to set the number
of RQs used in commit cc94d6c4d40c ("enic: Adjust used MSI-X
wq/rq/cq/interrupt resources in a more robust way")
This resulted in machines with less than 16 cpus using less than 8 RQs.
Allow enic to use at least 8 RQs no matter how many cpus are in the
machine to not impact existing enic workloads after a kernel upgrade.
Reviewed-by: John Daley <johndale@cisco.com>
Reviewed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250521-enic_min_8rq-v1-1-691bd2353273@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is [1/3] part of hinic3 Ethernet driver initial submission.
With this patch hinic3 is a valid kernel module but non-functional
driver.
The driver parts contained in this patch:
Module initialization.
PCI driver registration but with empty id_table.
Auxiliary driver registration.
Net device_ops registration but open/stop are empty stubs.
tx/rx logic.
All major data structures of the driver are fully introduced with the
code that uses them but without their initialization code that requires
management interface with the hw.
Co-developed-by: Xin Guo <guoxin09@huawei.com>
Signed-off-by: Xin Guo <guoxin09@huawei.com>
Signed-off-by: Fan Gong <gongfan1@huawei.com>
Co-developed-by: Gur Stavi <gur.stavi@huawei.com>
Signed-off-by: Gur Stavi <gur.stavi@huawei.com>
Link: https://patch.msgid.link/76a137ffdfe115c737c2c224f0c93b60ba53cc16.1747736586.git.gur.stavi@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Logic here always sets hdr->version to 2 if it is not a BE3 or Lancer chip,
even if it is BE2. Use 'else if' to prevent multiple assignments, setting
version 0 for BE2, version 1 for BE3 and Lancer, and version 2 for others.
Fixes potential incorrect version setting when BE2_chip and
BE3_chip/lancer_chip checks could both be true.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://patch.msgid.link/20250519141731.691136-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Aeonsemi AS21xxx 10G C45 PHYs. These PHYs integrate
an IPC to setup some configuration and require special handling to
sync with the parity bit. The parity bit is a way the IPC use to
follow correct order of command sent.
Supported PHYs AS21011JB1, AS21011PB1, AS21010JB1, AS21010PB1,
AS21511JB1, AS21511PB1, AS21510JB1, AS21510PB1, AS21210JB1,
AS21210PB1 that all register with the PHY ID 0x7500 0x7510
before the firmware is loaded.
They all support up to 5 LEDs with various HW mode supported.
While implementing it was found some strange coincidence with using the
same logic for implementing C22 in MMD regs in Broadcom PHYs.
For reference here the AS21xxx PHY name logic:
AS21x1xxB1
^ ^^
| |J: Supports SyncE/PTP
| |P: No SyncE/PTP support
| 1: Supports 2nd Serdes
| 2: Not 2nd Serdes support
0: 10G, 5G, 2.5G
5: 5G, 2.5G
2: 2.5G
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce new API, genphy_match_phy_device(), to provide a way to check
to match a PHY driver for a PHY device based on the info stored in the
PHY device struct.
The function generalize the logic used in phy_bus_match() to check the
PHY ID whether if C45 or C22 ID should be used for matching.
This is useful for custom .match_phy_device function that wants to use
the generic logic under some condition. (example a PHY is already setup
and provide the correct PHY ID)
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-5-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify .match_phy_device OP by using a generic function and using the
new phy_id PHY driver info instead of hardcoding the matching PHY ID
with new variant for macsec and no_macsec PHYs.
Also make use of PHY_ID_MATCH_MODEL macro and drop PHY_ID_MASK define to
introduce phy_id and phy_id_mask again in phy_driver struct.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify .match_phy_device OP by using a generic function and using the
new phy_id PHY driver info instead of hardcoding the matching PHY ID.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-3-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass PHY driver pointer to .match_phy_device OP in addition to phydev.
Having access to the PHY driver struct might be useful to check the
PHY ID of the driver is being matched for in case the PHY ID scanned in
the phydev is not consistent.
A scenario for this is a PHY that change PHY ID after a firmware is
loaded, in such case, the PHY ID stored in PHY device struct is not
valid anymore and PHY will manually scan the ID in the match_phy_device
function.
Having the PHY driver info is also useful for those PHY driver that
implement multiple simple .match_phy_device OP to match specific MMD PHY
ID. With this extra info if the parsing logic is the same, the matching
function can be generalized by using the phy_id in the PHY driver
instead of hardcoding.
Rust wrapper callback is updated to align to the new match_phy_device
arguments.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Benno Lossin <lossin@kernel.org> # for Rust
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a log should be printed as info level, not error level.
Fixes: 9bfd65980f8d ("net: libwx: Add sriov api for wangxun nics")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/67409DB57B87E2F0+20250519063357.21164-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
