| Age | Commit message (Collapse) | Author |
|---|
|
If platform_get_irq_byname returns -ENXIO fall back to legacy (index
based) mode, but on other errors function should return this error.
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250619132125.78368-5-linux@fw-web.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On SoCs with dedicated RX and TX interrupts (all except MT7621 and
MT7628) platform_get_irq() is called for the first IRQ (eth->irq[0])
but it is never used.
Skip the first IRQ and reduce the IRQ-count to 2.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250619132125.78368-4-linux@fw-web.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use consts instead of fixed integers for accessing IRQ array.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/20250619132125.78368-3-linux@fw-web.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add named interrupts and keep index based fallback for existing
devicetrees.
Currently only rx and tx IRQs are defined to be used with mt7988, but
later extended with RSS/LRO support.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250619132125.78368-2-linux@fw-web.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change error values of `ionic_tx_map_single()` and `ionic_tx_map_frag()`
from 0 to `DMA_MAPPING_ERROR` to prevent collision with 0 as a valid
address.
This also fixes the use of `dma_mapping_error()` to test against 0 in
`ionic_xdp_post_frame()`
Fixes: 0f3154e6bcb3 ("ionic: Add Tx and Rx handling")
Fixes: 56e41ee12d2d ("ionic: better dma-map error handling")
Fixes: ac8813c0ab7d ("ionic: convert Rx queue buffers to use page_pool")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://patch.msgid.link/20250619094538.283723-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
lpc18xx uses plat_dat->mac_interface, despite wanting to validate the
PHY interface. Checking the DT files (arch/arm/boot/dts/nxp/lpc/), none
of them specify mac-mode which means mac_interface and phy_interface
will be identical.
mac_interface is only used when there is some kind of MII converter
between the DesignWare MAC and PHY, and describes the interface mode
that the DW MAC needs to use, whereas phy_interface describes the
interface mode that the PHY uses.
Noting that lpc18xx only supports MII and RMII interface modes, switch
this glue driver to use plat_dat->phy_interface, and to mark that the
mac_interface is not used, explicitly set it to PHY_INTERFACE_MODE_NA.
The latter is safe as the only user of mac_interface for this platform
would be in stmmac_check_pcs_mode(), which only checks for RGMII or
SGMII.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Yanteng Si <siyanteng@cqsoftware.com.cn>
Link: https://patch.msgid.link/E1uSBri-004fL5-FI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IPQ5018 SoC contains a single internal Gigabit Ethernet PHY which
provides an MDI interface directly to an RJ45 connector or an external
switch over a PHY to PHY link.
The PHY supports 10BASE-T/100BASE-TX/1000BASE-T link modes in SGMII
interface mode, CDT, auto-negotiation and 802.3az EEE.
Let's add support for this PHY in the at803x driver as it falls within
the Qualcomm Atheros OUI.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://patch.msgid.link/20250613-ipq5018-ge-phy-v5-2-9af06e34ea6b@outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ath12k_dp_tx_get_encap_type(), the arvif parameter is only used to
retrieve the ab pointer. In vdev delete sequence the arvif->ar could
become NULL and that would trigger kernel panic.
Since the caller ath12k_dp_tx() already has a valid ab pointer, pass it
directly to avoid panic and unnecessary dereferencing.
PC points to "ath12k_dp_tx+0x228/0x988 [ath12k]"
LR points to "ath12k_dp_tx+0xc8/0x988 [ath12k]".
The Backtrace obtained is as follows:
ath12k_dp_tx+0x228/0x988 [ath12k]
ath12k_mac_tx_check_max_limit+0x608/0x920 [ath12k]
ieee80211_process_measurement_req+0x320/0x348 [mac80211]
ieee80211_tx_dequeue+0x9ac/0x1518 [mac80211]
ieee80211_tx_dequeue+0xb14/0x1518 [mac80211]
ieee80211_tx_prepare_skb+0x224/0x254 [mac80211]
ieee80211_xmit+0xec/0x100 [mac80211]
__ieee80211_subif_start_xmit+0xc50/0xf40 [mac80211]
ieee80211_subif_start_xmit+0x2e8/0x308 [mac80211]
netdev_start_xmit+0x150/0x18c
dev_hard_start_xmit+0x74/0xc0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Fixes: e93bbd65547e ("wifi: ath12k: fix packets are sent in native wifi mode while we set raw mode")
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250606044936.3989400-1-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the budget for monitor ring is reduced during each ring entry
reaping and again when the end reason is HAL_MON_END_OF_PPDU, leading to
inefficient budget use. The below mentioned commit intended to decrement
the budget only for HAL_MON_END_OF_PPDU but did not remove the other
decrement. Fix this by eliminating the budget decrement for each ring entry
reaping, ensuring the driver always reaps one full PPDU worth of entries
from the monitor destination ring.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 394a3fa7c538 ("wifi: ath12k: Optimize NAPI budget by adjusting PPDU processing")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250603103542.1164713-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The commit 89ac53e96217 ("wifi: ath12k: Enable REO queue lookup table
feature on QCN9274") originally intended to enable the reoq_lut_support
hardware parameter flag for both QCN9274 hw1.0 and hw2.0. However,
it enabled it only for QCN9274 hw1.0.
Hence, enable REO queue lookup table feature on QCN9274 hw2.0.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250609-qcn9274-reoq-v1-1-a92c91abc9b9@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warning:
drivers/net/wireless/ath/ath12k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-5-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath11k/ce.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/coredump.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/debugfs.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/dp.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/fw.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/hal.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/pcic.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/qmi.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/trace.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-4-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath10k/bmi.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/ce.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/coredump.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htc.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htt_rx.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htt_tx.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/mac.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/trace.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-3-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath9k/common-beacon.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common-debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common-init.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common-spectral.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/dynack.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/hw.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-2-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warning:
drivers/net/wireless/ath/main.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-1-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, TID is not decremented before peer cleanup, during error
handling path of ath12k_dp_rx_peer_frag_setup(). This could lead to
out-of-bounds access in peer->rx_tid[].
Hence, add a decrement operation for TID, before peer cleanup to
ensures proper cleanup and prevents out-of-bounds access issues when
the RX peer frag setup fails.
Found during code review. Compile tested only.
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250526034713.712592-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
ath12k_dp_rx_deliver_msdu() currently includes logic related to
monitor mode handling. This code was inherited from the ath11k driver,
where a single rx handler was used for both regular and monitor mode
packets. In ath12k, however, monitor mode packets are handled separately
via ath12k_dp_mon_rx_deliver_msdu(), which contains all the necessary
monitor-specific logic. Therefore, monitor-related checks and operations
in ath12k_dp_rx_deliver_msdu() are no longer needed. Remove this dead code
to simplify the rx path and avoid unnecessary per-packet checks.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250605054438.1855365-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
As station, WCN7850 firmware requires pairwise key to be installed before
group key. Currently host does not care about this, so it is up to kernel
or userspace to decide which one will be installed first. In case above
requirement is not met, WCN7850 firmware's EAPOL station machine is messed
up, and finally connection fails [1].
Reorder key install for station interface in that case: this is done by
caching group key first; Later when pairwise key arrives, both can be
installed in required order.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00217-QCAHKSWPL_SILICONZ-1
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218733
Link: https://lore.kernel.org/all/AS8P190MB12051DDBD84CD88E71C40AD7873F2@AS8P190MB1205.EURP190.PROD.OUTLOOK.COM # [1]
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250523-ath12k-unicast-key-first-v1-2-f53c3880e6d8@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
WMI_KEY_PAIRWISE and WMI_KEY_GROUP are not bit fields, change
bit operation to direct assignment to avoid confusion.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00217-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250523-ath12k-unicast-key-first-v1-1-f53c3880e6d8@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
If a regulatory notification is there in the system while the hardware is
being registered, it attempts to set the new regulatory country. However,
ath12k currently boots with a default country derived from the BDF. If this
default country differs from the one provided in the notification, a race
condition can occur while updating the regulatory information back to
userspace. This potentially leads to driver having the incorrect regulatory
applied.
For example, suppose the regulatory domain for France (FR) is already
applied, and then the driver is loaded with a BDF that has the United
States (US) country programmed. When the driver finishes loading, the
regulatory domain shown in phyX still reflects the US regulatory settings.
This is incorrect, as the driver had already received a notification for
FR during hardware registration, but failed to process it properly due to
the race condition.
The race condition exists during driver initialization and hardware
registration:
- On driver load, the firmware sends BDF-based country regulatory rules,
which are stored in default_regd via ath12k_reg_handle_chan_list().
- During hardware registration, a regulatory notification is triggered
through:
ath12k_mac_hw_register()
-> ieee80211_register_hw()
-> wiphy_register()
-> wiphy_regulatory_register()
-> reg_call_notifier()
This sends a country code to the firmware, which responds with updated
regulatory rules.
- After registration, ath12k_mac_hw_register() calls ath12k_regd_update(),
which copies default_regd and passes it to the upper layers.
The race occurs between the firmware's response and the execution of
ath12k_regd_update(). If the firmware's new rules are processed before the
update call, the correct values are used. Otherwise, outdated boot-time
country settings are exposed to userspace.
To resolve this issue, introduce a completion mechanism within the hardware
group (ah). Trigger this completion whenever a regulatory change is
requested from the firmware. Then, in ath12k_regd_update(), wait for the
firmware to complete its regulatory processing before proceeding with the
update.
This ensures that during driver load, the default country is processed
first. However, before ath12k_regd_update() is called, the new regulatory
notification will have already been received by the driver. As a result, it
will wait for the firmware's regulatory processing to complete, and only
the final, correct regulatory domain will be updated to userspace.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250617-handle_user_regd_update_hints_during_insmod-v2-1-10a6a48efe81@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
With previous patch [1], ath12k_reg_update_chan_list() will be called
during reg_process_self_managed_hint().
reg_process_self_managed_hint() will hold rtnl_lock all the time.
But ath12k_reg_update_chan_list() may increase the occupation time of
rtnl_lock, because when wait flag is set, wait_for_completion_timeout()
will be called during 11d/hw scan.
Should minimize the occupation time of rtnl_lock as much as possible
to avoid interfering with rest of the system. So move the update channel
list operation to a new worker, so that wait_for_completion_timeout()
won't be called with the rtnl_lock held.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: f335295aa29c ("wifi: ath12k: avoid deadlock during regulatory update in ath12k_regd_update()") #[1]
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250605082528.701-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
When two split-phy devices that support overlapping frequency ranges within
the same band are grouped into an ath12k hardware (HW) setup, they share a
common wiphy instance. Consequently, the channel list (wiphy->bands[])
becomes unified across all associated radios (ar).
For reference, the devices are:
2.4 GHz + 5 GHz Low Band
5 GHz High Band + 6 GHz
The first radio probed within the 5 GHz range (say 5 GHz Low Band) updates
its sband reference (&ar->mac.sbands[NL80211_BAND_5GHZ]) within
wiphy->bands[]. However, when the second 5 GHz radio (5 GHz High Band) is
probed, it replaces the existing wiphy->bands[] entry with its own sub-band
reference. As a result, wiphy->bands[] always reflects the channel list
from the most recently probed radio in that band, restricting supported
channels to those within its specific range for upper-layer.
Fix this by updating the wiphy->bands[] to just enable the channels of
current radio when there exist a radio which already has set it.
This will make sure wiphy->bands[] holds reference of first radio which
got probed in 5 GHz band and subsequent radio just updates the channel list
in the same address space.
Since same sband memory space is shared between radios of a band, while
determining the allowed frequency range of radio, its frequency limits
(ar->freq_range.start_freq, end_freq) should be used.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522111514.3735107-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
When two split-phy devices having supported frequency range in same band
(as mentioned below) are combined into an ath12k HW group, they will be
part of same wiphy and hence the channel list (wiphy->bands[]) will be
common for all of the radios (ar).
1 - 2.4 GHz + 5 GHz Low band
2 - 5 GHz High band + 6 GHz
When a scan is triggered with frequency list containing frequencies of
both 5 GHz low and 5 GHz high, mac80211 generates a single scan request
to driver with both the frequencies. This is because mac80211 splits the
scan request based on band.
ath12k checks the first frequency in the requested scan frequency list and
initiates scan to corresponding radio's(ar) firmware with all the
frequencies. Firmware rejects this scan as some frequencies in the scan
request are not supported, resulting is scan failure.
Fix this by splitting the scan request into multiples scans in driver
based on the supported frequency range of different radios in a band and
schedule scans in parallel to them.
Finally send scan completion/abort notification to mac80211 after all the
radios complete their scheduled scan.
Also, last_scan_link is not needed anymore as ath12k internally schedules
multiple scans, remove the same and use ahvif->links_map to identify
scan links when scan is cancelled.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Co-developed-by: Vignesh C <quic_vignc@quicinc.com>
Signed-off-by: Vignesh C <quic_vignc@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250507194832.2501668-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
When two split-phy devices that support overlapping frequency ranges within
the same band(say 5 GHz low and 5 GHz high) are grouped into an ath12k
hardware (HW) setup, they share a common wiphy instance. Consequently, the
channel list (wiphy->bands[]) becomes unified across all associated
radios (ar).
When a scan is triggered with frequency list containing frequencies of
both 5 GHz low and 5 GHz high, mac80211 generates a single scan request
to driver with all the frequencies. This is because mac80211 splits the
scan request based on band.
ath12k checks the first frequency in the requested scan frequency list and
initiates scan to corresponding radio's(ar) firmware with all the
frequencies. Firmware rejects this scan since some of the frequencies in
the scan request are not supported, resulting in a scan failure.
To fix this ath12k driver should split the scan request into multiple
scans based on requested frequencies and schedule them to corresponding
underlying radio(s) in parallel.
Currently, ath12k driver assigns the scan link (link 15) in ahvif->links[]
for scan vdev creation. However, with parallel scan support being
introduced in the following patch, multiple radios (e.g., 5 GHz low and
5 GHz high) in the same HW group may attempt to use the same scan link
concurrently, causing conflicts where the vdev created by one radio could
be deleted and re-initialized by another.
To address this, reserve space for additional scan links for each radio in
a MLO group and allow subsequent radios to use different available scan
links (ahvif->link[15..MAX_SCAN_LINKS]) when scan link (15) is
pre-occupied.
While at it, rename ATH12K_DEFAULT_SCAN_LINK as ATH12K_FIRST_SCAN_LINK
as there is no longer only one scan link.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250507194832.2501668-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
In MLO configuration, ath12k_mac_radio_start() iterates through all
the radios and makes the ar state 'ON'. Even though some bands are
not supported in certain countries, ath12k_reg_update_chan_list()
tries to update the channel list for all the active pdevs and ends
up in the warn_on for non-supported band.
To prevent this, disable the pdev when the number of channels across
all bands supported by the pdev is zero for a particular country.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250506214930.3561348-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
During beacon miss handling, ath12k driver iterates over active virtual
interfaces (vifs) and attempts to access the radio object (ar) via
arvif->deflink->ar.
However, after commit aa80f12f3bed ("wifi: ath12k: defer vdev creation for
MLO"), arvif is linked to a radio only after vdev creation, typically when
a channel is assigned or a scan is requested.
For P2P capable devices, a default P2P interface is created by
wpa_supplicant along with regular station interfaces, these serve as dummy
interfaces for P2P-capable stations, lack an associated netdev and initiate
frequent scans to discover neighbor p2p devices. When a scan is initiated
on such P2P vifs, driver selects destination radio (ar) based on scan
frequency, creates a scan vdev, and attaches arvif to the radio. Once the
scan completes or is aborted, the scan vdev is deleted, detaching arvif
from the radio and leaving arvif->ar uninitialized.
While handling beacon miss for station interfaces, P2P interface is also
encountered in the vif iteration and ath12k_mac_handle_beacon_miss_iter()
tries to dereference the uninitialized arvif->deflink->ar.
Fix this by verifying that vdev is created for the arvif before accessing
its ar during beacon miss handling and similar vif iterator callbacks.
==========================================================================
wlp6s0: detected beacon loss from AP (missed 7 beacons) - probing
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 5 UID: 0 PID: 0 Comm: swapper/5 Not tainted 6.16.0-rc1-wt-ath+ #2 PREEMPT(full)
RIP: 0010:ath12k_mac_handle_beacon_miss_iter+0xb5/0x1a0 [ath12k]
Call Trace:
__iterate_interfaces+0x11a/0x410 [mac80211]
ieee80211_iterate_active_interfaces_atomic+0x61/0x140 [mac80211]
ath12k_mac_handle_beacon_miss+0xa1/0xf0 [ath12k]
ath12k_roam_event+0x393/0x560 [ath12k]
ath12k_wmi_op_rx+0x1486/0x28c0 [ath12k]
ath12k_htc_process_trailer.isra.0+0x2fb/0x620 [ath12k]
ath12k_htc_rx_completion_handler+0x448/0x830 [ath12k]
ath12k_ce_recv_process_cb+0x549/0x9e0 [ath12k]
ath12k_ce_per_engine_service+0xbe/0xf0 [ath12k]
ath12k_pci_ce_workqueue+0x69/0x120 [ath12k]
process_one_work+0xe3a/0x1430
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: aa80f12f3bed ("wifi: ath12k: defer vdev creation for MLO")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250618185635.750470-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
clang gets a bit confused by the code in the qed_mfw_process_tlv_req and
ends up spilling registers to the stack hundreds of times. When sanitizers
are enabled, this can end up blowing the stack warning limit:
drivers/net/ethernet/qlogic/qed/qed_mng_tlv.c:1244:5: error: stack frame size (1824) exceeds limit (1280) in 'qed_mfw_process_tlv_req' [-Werror,-Wframe-larger-than]
Apparently the problem is the complexity of qed_mfw_update_tlvs()
after inlining, and marking the four main branches of that function
as noinline_for_stack makes this problem completely go away, the stack
usage goes down to 100 bytes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need the driver-core fixes that are in 6.16-rc3 into here as well
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
skb may be freed as soon as we put it on the rx queue.
Use the len variable like the code did prior to the conversion.
Fixes: f9e2511d80c2 ("netdevsim: migrate to dstats stats collection")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ice: Separate TSPLL from PTP and clean up [part]
Jake Keller says:
Separate TSPLL related functions and definitions from all PTP-related
files and clean up the code by implementing multiple helpers.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: add TSPLL log config helper
ice: use designated initializers for TSPLL consts
ice: remove ice_tspll_params_e825 definitions
ice: fix E825-C TSPLL register definitions
ice: rename TSPLL and CGU functions and definitions
ice: move TSPLL functions to a separate file
====================
Link: https://patch.msgid.link/20250618174231.3100231-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
Reviewed-by: Jijie Shao<shaojijie@huawei.com>
Link: https://patch.msgid.link/20250618203823.1336156-10-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
Zeroing data on SET is not necessary, the argument is not copied
back to user space. The driver has no other RXNFC functionality
so the SET callback can be now removed.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250618203823.1336156-9-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
Acked-by: Louis Peens <louis.peens@corigine.com>
Link: https://patch.msgid.link/20250618203823.1336156-8-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Link: https://patch.msgid.link/20250618203823.1336156-7-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250618203823.1336156-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
The driver has no other RXNFC functionality so the SET callback can
be now removed.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250618203823.1336156-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
This driver's RXFH config is read only / fixed so the conversion
is purely factoring out the handling into a helper. One thing of
note that this is one of the two drivers which pays attention to
rss_context.
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20250618203823.1336156-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
This driver's RXFH config is read only / fixed so the conversion
is purely factoring out the handling into a helper.
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20250618203823.1336156-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate to new callbacks added by commit 9bb00786fc61 ("net: ethtool:
add dedicated callbacks for getting and setting rxfh fields").
This driver's RXFH config is read only / fixed so the conversion
is purely factoring out the handling into a helper.
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20250618203823.1336156-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use netmem_dma_*() helpers and declare netmem_tx to support netmem TX.
By this change, all bnxt devices will support the netmem TX.
Unreadable skbs are not going to be handled by the TX push logic.
So, it checks whether a skb is readable or not before the TX push logic.
netmem TX can be tested with ncdevmem.c
Acked-by: Mina Almasry <almasrymina@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250619144058.147051-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rcar_canfd_f_*() inline functions to obtain channel-specific CAN-FD
register offsets really describe a memory layout. Hence replace them by
a C structure, to simplify the code, and reduce kernel size.
This also gets rid of warnings about unused rcar_canfd_f_*() inline
functions, which are reported by recent versions of clang.
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/20250618183827.5bebca8f@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/292b75b3bc8dd95f805f0223f606737071c8cf86.1750327217.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for SIMCom 8230C which is based on Qualcomm SDX35 chip.
0x9071: tty (DM) + tty (NMEA) + tty (AT) + rmnet
T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1e0e ProdID=9071 Rev= 5.15
S: Manufacturer=SIMCOM
S: Product=SDXBAAGHA-IDP _SN:D744C4C5
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=none
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Xiaowei Li <xiaowei.li@simcom.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://patch.msgid.link/tencent_21D781FAA4969FEACA6ABB460362B52C9409@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds support for XDP_TX and XDP_REDIRECT for the DQ RDA
queue format. To appropriately support transmission of XDP frames, a
new pending packet type GVE_TX_PENDING_PACKET_DQO_XDP_FRAME is
introduced for completion handling, as there was a previous assumption
that completed packets would be SKBs.
XDP_TX handling completes the basic XDP actions, so the feature is
recorded accordingly. This patch also enables the ndo_xdp_xmit callback
allowing DQ to handle XDP_REDIRECT packets originating from another
interface.
The XDP spinlock is moved to common TX ring fields so that it can be
used in both GQ and DQ. Originally, it was in a section which was
mutually exclusive for GQ and DQ.
In summary, 3 XDP features are exposed for the DQ RDA queue format:
1) NETDEV_XDP_ACT_BASIC
2) NETDEV_XDP_ACT_NDO_XMIT
3) NETDEV_XDP_ACT_REDIRECT
Note that XDP and header-data split are mutually exclusive for the time
being due to lack of multi-buffer XDP support.
This patch does not add support for the DQ QPL format. That is to come
in a future patch series.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch performs various minor DQO TX datapath refactors in
preparation for adding XDP_TX and XDP_REDIRECT support. The following
refactors are performed:
1) gve_tx_fill_pkt_desc_dqo() relies on a SKB pointer to
get whether checksum offloading should be enabled. This won't work
for the XDP case, which does not have a SKB. This patch updates the
method to use a boolean representing whether checksum offloading
should be enabled directly.
2) gve_maybe_stop_dqo() contains some synchronization between the true
TX head and the cached value, a synchronization which is common for
XDP queues and normal netdev queues. However, that method is reserved
for netdev TX queues. To avoid duplicate code, this logic is factored
out into a new method, gve_has_tx_slots_available().
3) gve_tx_update_tail() is added to update the TX tail, a functionality
that will be common between normal TX and XDP TX codepaths.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for XDP DQ support, the gve_xdp_xmit callback needs to
be generalized for all queue formats. This patch renames the GQ-specific
function to gve_xdp_xmit_gqi, and introduces a new gve_xdp_xmit callback
which branches on queue format.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rvu_mbox_init function makes use of error path for
freeing memory which are local to the function in
both success and failure conditions. This is unusual hence
fix it by returning zero on success. With new cn20k code this
is freeing valid memory in success case also.
Fixes: e53ee4acb220 ("octeontx2-af: CN20k basic mbox operations and structures")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't populate the read-only array cfg_offset on the stack at run time,
instead make it static const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250619082554.1834654-1-colin.i.king@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since secs_to_jiffies()(commit:b35108a51cf7) has been introduced, we can
use it to avoid scaling the time to msec.
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Link: https://patch.msgid.link/20250613102624.3077418-1-liyuesong@vivo.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since secs_to_jiffies()(commit:b35108a51cf7) has been introduced, we can
use it to avoid scaling the time to msec.
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20250612021446.3465972-1-liyuesong@vivo.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Enable the host MLME flag to allow supported W8997 chipsets to
use WPA3. This feature requires firmware support (V2 API key), which
the driver validates before activation.
Tested using sdsd8997_combo_v4.bin from commit
211fbc287a0b ("linux-firmware: Update FW files for MRVL SD8997 chips")
[ 5.956510] mwifiex_sdio mmc2:0001:1: info: FW download over, size 623352 bytes
...
[ 6.825456] mwifiex_sdio mmc2:0001:1: WLAN FW is active
...
[ 12.171950] mwifiex_sdio mmc2:0001:1: host_mlme: enable, key_api: 2
[ 12.226206] mwifiex_sdio mmc2:0001:1: info: MWIFIEX VERSION: mwifiex 1.0 (16.68.1.p197)
root@verdin-imx8mm-14700070:~# strings /lib/firmware/mrvl/sdsd8997_combo_v4.bin |grep 16
$Id: w8997o-V4, RF878X, FP68_LINUX, 16.68.1.p197.1 $
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Link: https://patch.msgid.link/20250530094711.915574-1-rafael@beims.me
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
