| Age | Commit message (Collapse) | Author |
|---|
|
Add a bare minimum amount of changes in order to support PCIe Root
Complex hardware IP found on RPi5. The PCIe controller on BCM2712
is based on BCM7712 and as such it inherits register offsets, PERST#
assertion, bridge_reset ops, and inbound windows count.
Although, the implementation for BCM2712 needs a workaround related to
the control of the bridge_reset where turning off of the Root Port must
not shutdown the bridge_reset and this must be avoided. To implement
this workaround a quirks field is introduced in pcie_cfg_data struct.
The controller also needs adjustment of PHY PLL setup to use a 54MHz
input refclk. The default input reference clock for the PHY PLL is
100Mhz, except for some devices where it is 54Mhz like BCM2712C1 and
BCM2712D0.
To implement those adjustments introduce a new .post_setup op in
pcie_cfg_data and call it at the end of brcm_pcie_setup function.
The BCM2712 .post_setup callback implements the required MDIO writes
that switch the PLL refclk and also change PHY PM clock period.
Without this RPi5 PCIex1 is unable to enumerate endpoint devices on
the expansion connector.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-8-svarbanov@suse.de
[commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Per the Cadence's "PCIe Controller IP for AX14" user guide, Version
1.04, Section 9.1.7.1, "AXI Subordinate to PCIe Address Translation
Registers", Table 9.4, the bit 16 of the AXI Subordinate Address
(axi_s_awaddr) when set corresponds to MSG with data, and when not set,
to MSG without data.
However, the driver is currently doing the opposite and due to this,
the INTx is never received on the host.
So, fix the driver to reflect the documentation and also make INTx work.
Fixes: 37dddf14f1ae ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Hans Zhang <hans.zhang@cixtech.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214165724.184599-1-18255117159@163.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The new dw_pcie_find_vsec_capability() helper will be used within
different DWC APIs to find the VSEC capabilities like PTM, RAS, etc.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-3-shradha.t@samsung.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Configure PBus base address and address mask to allow the hw
to detect if a given address is accessible on PCIe controller.
Fixes: f6ab898356dd ("PCI: mediatek-gen3: Add Airoha EN7581 support")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20250225-en7581-pcie-pbus-csr-v4-2-24324382424a@kernel.org
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The BCM2712 memory map can support up to 64GB of system memory, thus
expand the inbound window size in calculation helper function.
The change is safe for the currently supported SoCs that have smaller
inbound window sizes.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-7-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Instead of copying fields from the pcie_cfg_data structure to
brcm_pcie, reference it directly.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelil <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-6-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Then the brcmstb PCIe driver and MIP MSI-X interrupt controller
drivers are built as modules there could be a race in probing.
To avoid this, add a softdep to MIP driver to guarantee that
MIP driver will be load first.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-5-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Calling cpumask_next_wrap_old() with starting CPU == nr_cpu_ids
is effectively the same as request to find first CPU, starting
from a given one and wrapping around if needed.
cpumask_next_wrap() is a proper replacement for that.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
|
|
The next patch aligns implementation of cpumask_next_wrap() with the
find_next_bit_wrap(), and it changes function signature.
To make the transition smooth, this patch deprecates current
implementation by adding an _old suffix. The following patches switch
current users to the new implementation one by one.
No functional changes were intended.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
|
|
Enable PCIe Endpoint mode support for the Qualcomm SAR2130P platform.
This is needed, as it is not possible to use a compatible fallback on
any other platform since SAR2130P uses slightly different set of clocks.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250221-sar2130p-pci-v3-6-61a0fdfb75b4@linaro.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
A call to of_parse_phandle() is incrementing the refcount, and as such,
the of_node_put() must be called when the reference is no longer needed.
Thus, refactor the existing code and add a missing of_node_put() call
following the check to ensure that "msi_np" matches "pcie->np" and after
MSI initialization, but only if the MSI support is enabled system-wide.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 40ca1bf580ef ("PCI: brcmstb: Add MSI support")
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250122222955.1752778-1-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
On all Qcom endpoint SoCs, BAR0/BAR2 are 64bit BARs by default and
software cannot change the type.
So, mark the those BARs as 64bit BARs and also mark the successive
BAR1/BAR3 as RESERVED BARs so that the EPF drivers cannot use them.
Cc: stable+noautosel@kernel.org # depends on patch introducing only_64bit flag
Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241231130224.38206-3-manivannan.sadhasivam@linaro.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Remove a leftover assert for mac_reset line in mtk_pcie_en7581_power_up().
This is not harmful since EN7581 does not requires mac_reset and
mac_reset is not defined in EN7581 device tree.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250201-pcie-en7581-remove-mac_reset-v2-1-a06786cdc683@kernel.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The VF driver controls an endpoint attached to the PCI HyperV
controller. An invalidation sent by the PF driver in the host
would be delivered *to* the endpoint driver by the controller
driver.
Thus, correct the wording within the comment.
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20250207190716.89995-1-eahariha@linux.microsoft.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Batch sizing of multiple BARs while memory decoding is disabled
instead of disabling/enabling decoding for each BAR individually;
this optimizes virtualized environments where toggling decoding
enable is expensive (Alex Williamson)
- Add host bridge .enable_device() and .disable_device() hooks for
bridges that need to configure things like Requester ID to StreamID
mapping when enabling devices (Frank Li)
- Extend struct pci_ecam_ops with .enable_device() and
.disable_device() hooks so drivers that use pci_host_common_probe()
instead of their own .probe() have a way to set the
.enable_device() callbacks (Marc Zyngier)
- Drop 'No bus range found' message so we don't complain when DTs
don't specify the default 'bus-range = <0x00 0xff>' (Bjorn Helgaas)
- Rename the drivers/pci/of_property.c struct of_pci_range to
of_pci_range_entry to avoid confusion with the global of_pci_range
in include/linux/of_address.h (Bjorn Helgaas)
Driver binding:
- Update resource request API documentation to encourage callers to
supply a driver name when requesting resources (Philipp Stanner)
- Export pci_intx_unmanaged() and pcim_intx() (always managed) so
callers of pci_intx() (which is sometimes managed) can explicitly
choose the one they need (Philipp Stanner)
- Convert drivers from pci_intx() to always-managed pcim_intx() or
never-managed pci_intx_unmanaged(): amd_sfh, ata (ahci, ata_piix,
pata_rdc, sata_sil24, sata_sis, sata_uli, sata_vsc), bnx2x, bna,
ntb, qtnfmac, rtsx, tifm_7xx1, vfio, xen-pciback (Philipp Stanner)
- Remove pci_intx_unmanaged() since pci_intx() is now always
unmanaged and pcim_intx() is always managed (Philipp Stanner)
Error handling:
- Unexport pcie_read_tlp_log() to encourage drivers to use PCI core
logging rather than building their own (Ilpo Järvinen)
- Move TLP Log handling to its own file (Ilpo Järvinen)
- Store number of supported End-End TLP Prefixes always so we can
read the correct number of DWORDs from the TLP Prefix Log (Ilpo
Järvinen)
- Read TLP Prefixes in addition to the Header Log in
pcie_read_tlp_log() (Ilpo Järvinen)
- Add pcie_print_tlp_log() to consolidate printing of TLP Header and
Prefix Log (Ilpo Järvinen)
- Quirk the Intel Raptor Lake-P PIO log size to accommodate vendor
BIOSes that don't configure it correctly (Takashi Iwai)
ASPM:
- Save parent L1 PM Substates config so when we restore it along with
an endpoint's config, the parent info isn't junk (Jian-Hong Pan)
Power management:
- Avoid D3 for Root Ports on TUXEDO Sirius Gen1 with old BIOS because
the system can't wake up from suspend (Werner Sembach)
Endpoint framework:
- Destroy the EPC device in devm_pci_epc_destroy(), which previously
didn't call devres_release() (Zijun Hu)
- Finish virtual EP removal in pci_epf_remove_vepf(), which
previously caused a subsequent pci_epf_add_vepf() to fail with
-EBUSY (Zijun Hu)
- Write BAR_MASK before iATU registers in pci_epc_set_bar() so we
don't depend on the BAR_MASK reset value being larger than the
requested BAR size (Niklas Cassel)
- Prevent changing BAR size/flags in pci_epc_set_bar() to prevent
reads from bypassing the iATU if we reduced the BAR size (Niklas
Cassel)
- Verify address alignment when programming iATU so we don't attempt
to write bits that are read-only because of the BAR size, which
could lead to directing accesses to the wrong address (Niklas
Cassel)
- Implement artpec6 pci_epc_features so we can rely on all drivers
supporting it so we can use it in EPC core code (Niklas Cassel)
- Check for BARs of fixed size to prevent endpoint drivers from
trying to change their size (Niklas Cassel)
- Verify that requested BAR size is a power of two when endpoint
driver sets the BAR (Niklas Cassel)
Endpoint framework tests:
- Clear pci-epf-test dma_chan_rx, not dma_chan_tx, after freeing
dma_chan_rx (Mohamed Khalfella)
- Correct the DMA MEMCPY test so it doesn't fail if the Endpoint
supports both DMA_PRIVATE and DMA_MEMCPY (Manivannan Sadhasivam)
- Add pci-epf-test and pci_endpoint_test support for capabilities
(Niklas Cassel)
- Add Endpoint test for consecutive BARs (Niklas Cassel)
- Remove redundant comparison from Endpoint BAR test because a > 1MB
BAR can always be exactly covered by iterating with a 1MB buffer
(Hans Zhang)
- Move and convert PCI Endpoint tests from tools/pci to Kselftests
(Manivannan Sadhasivam)
Apple PCIe controller driver:
- Convert StreamID mapping configuration from a bus notifier to the
.enable_device() and .disable_device() callbacks (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Add Requester ID to StreamID mapping configuration when enabling
devices (Frank Li)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank
Li)
- Add DT binding for optional i.MX95 Refclk and driver support to
enable it if the platform hasn't enabled it (Richard Zhu)
- Configure PHY based on controller being in Root Complex or Endpoint
mode (Frank Li)
- Rely on dbi2 and iATU base addresses from DT via
dw_pcie_get_resources() instead of hardcoding them (Richard Zhu)
- Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
asserted in imx_pcie_assert_core_reset() (Richard Zhu)
- Add missing reference clock enable or disable logic for IMX6SX,
IMX7D, IMX8MM (Richard Zhu)
- Remove redundant imx7d_pcie_init_phy() since
imx7d_pcie_enable_ref_clk() does the same thing (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead
of syscon_regmap_lookup_by_phandle() followed by
of_property_read_u32_array() (Krzysztof Kozlowski)
Marvell MVEBU PCIe controller driver:
- Add MODULE_DEVICE_TABLE() to enable module autoloading (Liao Chen)
MediaTek PCIe Gen3 controller driver:
- Use clk_bulk_prepare_enable() instead of separate
clk_bulk_prepare() and clk_bulk_enable() (Lorenzo Bianconi)
- Rearrange reset assert/deassert so they're both done in the
*_power_up() callbacks (Lorenzo Bianconi)
- Document that Airoha EN7581 requires PHY init and power-on before
PHY reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo
Bianconi)
- Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)
- Sleep instead of delay during Airoha EN7581 power-up, since this is
a non-atomic context (Lorenzo Bianconi)
- Skip PERST# assertion on Airoha EN7581 during probe and
suspend/resume to avoid a hardware defect (Lorenzo Bianconi)
- Enable async probe to reduce system startup time (Douglas Anderson)
Microchip PolarFlare PCIe controller driver:
- Set up the inbound address translation based on whether the
platform allows coherent or non-coherent DMA (Daire McNamara)
- Update DT binding such that platforms are DMA-coherent by default
and must specify 'dma-noncoherent' if needed (Conor Dooley)
Mobiveil PCIe controller driver:
- Convert mobiveil-pcie.txt to YAML and update 'interrupt-names'
and 'reg-names' (Frank Li)
Qualcomm PCIe controller driver:
- Add DT SM8550 and SM8650 optional 'global' interrupt for link
events (Neil Armstrong)
- Add DT 'compatible' strings for IPQ5424 PCIe controller (Manikanta
Mylavarapu)
- If 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
Renesas R-Car PCIe controller driver:
- Avoid passing stack buffer as resource name (King Dix)
Rockchip PCIe controller driver:
- Simplify clock and reset handling by using bulk interfaces (Anand
Moon)
- Pass typed rockchip_pcie (not void) pointer to
rockchip_pcie_disable_clocks() (Anand Moon)
- Return -ENOMEM, not success, when pci_epc_mem_alloc_addr() fails
(Dan Carpenter)
Rockchip DesignWare PCIe controller driver:
- Use dll_link_up IRQ to detect Link Up and enumerate devices so
users don't have to manually rescan (Niklas Cassel)
- Tell DWC core not to wait for link up since the 'sys' interrupt is
required and detects Link Up events (Niklas Cassel)
Synopsys DesignWare PCIe controller driver:
- Don't wait for link up in DWC core if driver can detect Link Up
event (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya
chundru)
- Always stop link in dw_pcie_suspend_noirq(), which is required at
least for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending
PME_TURN_OFF message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program
an internal Address Translation Unit (iATU) (Frank Li)
TI DRA7xx PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
(Krzysztof Kozlowski)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Xilinx Versal CPM5
(Thippeswamy Havalige)
MicroSemi Switchtec management driver:
- Add Microchip PCI100X device IDs (Rakesh Babu Saladi)
Miscellaneous:
- Move reset related sysfs code from pci.c to pci-sysfs.c where other
similar code lives (Ilpo Järvinen)
- Simplify reset_method_store() memory management by using __free()
instead of explicit kfree() cleanup (Ilpo Järvinen)
- Constify struct bin_attribute for sysfs, VPD, P2PDMA, and the IBM
ACPI hotplug driver (Thomas Weißschuh)
- Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT (Dongdong
Zhang)
- Correct documentation of the 'config_acs=' kernel parameter
(Akihiko Odaki)"
* tag 'pci-v6.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (111 commits)
PCI: Batch BAR sizing operations
dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
PCI: microchip: Set inbound address translation for coherent or non-coherent mode
Documentation: Fix pci=config_acs= example
PCI: Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT
PCI: Don't include 'pm_wakeup.h' directly
selftests: pci_endpoint: Migrate to Kselftest framework
selftests: Move PCI Endpoint tests from tools/pci to Kselftests
misc: pci_endpoint_test: Fix IOCTL return value
dt-bindings: PCI: qcom: Document the IPQ5424 PCIe controller
dt-bindings: PCI: qcom,pcie-sm8550: Document 'global' interrupt
dt-bindings: PCI: mobiveil: Convert mobiveil-pcie.txt to YAML
PCI: switchtec: Add Microchip PCI100X device IDs
misc: pci_endpoint_test: Remove redundant 'remainder' test
misc: pci_endpoint_test: Add consecutive BAR test
misc: pci_endpoint_test: Add support for capabilities
PCI: endpoint: pci-epf-test: Add support for capabilities
PCI: endpoint: pci-epf-test: Fix check for DMA MEMCPY test
PCI: endpoint: pci-epf-test: Set dma_chan_rx pointer to NULL on error
PCI: dwc: Simplify config resource lookup
...
|
|
- Add DT binding and driver support for Xilinx Versal CPM5 (Thippeswamy
Havalige)
* pci/controller/xilinx-cpm:
PCI: xilinx-cpm: Add support for Versal CPM5 Root Port Controller 1
dt-bindings: PCI: xilinx-cpm: Add compatible string for CPM5 host1
|
|
- Add struct rockchip_pcie_ep kernel-doc to fix warnings (Damien Le Moal)
- Simplify clock and reset handling by using bulk interfaces (Anand Moon)
- Pass typed rockchip_pcie (not void) pointer to
rockchip_pcie_disable_clocks() (Anand Moon)
- Return -ENOMEM, not success, when pci_epc_mem_alloc_addr() fails (Dan
Carpenter)
* pci/controller/rockchip:
PCI: rockchip-ep: Fix error code in rockchip_pcie_ep_init_ob_mem()
PCI: rockchip: Refactor rockchip_pcie_disable_clocks() signature
PCI: rockchip: Simplify reset control handling by using reset_control_bulk*() function
PCI: rockchip: Simplify clock handling by using clk_bulk*() functions
PCI: rockchip: Add missing fields descriptions for struct rockchip_pcie_ep
|
|
- Avoid passing stack buffer as resource name (King Dix)
* pci/controller/rcar-ep:
PCI: rcar-ep: Fix incorrect variable used when calling devm_request_mem_region()
|
|
- Add MODULE_DEVICE_TABLE() to enable module autoloading (Liao Chen)
* pci/controller/mvebu:
PCI: mvebu: Enable module autoloading
|
|
- Set up the inbound address translation based on whether the platform
allows coherent or non-coherent DMA (Daire McNamara)
- Update DT binding such that platforms are DMA-coherent by default and
must specify 'dma-noncoherent' if needed (Conor Dooley)
* pci/controller/microchip:
dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
PCI: microchip: Set inbound address translation for coherent or non-coherent mode
|
|
- Use clk_bulk_prepare_enable() instead of separate clk_bulk_prepare() and
clk_bulk_enable() (Lorenzo Bianconi)
- Rearrange reset assert/deassert so they're both done in the *_power_up()
callbacks (Lorenzo Bianconi)
- Document that Airoha EN7581 requires PHY init and power-on before PHY
reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo Bianconi)
- Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)
- Sleep instead of delay during Airoha EN7581 power-up, since this is a
non-atomic context (Lorenzo Bianconi)
- Skip PERST# assertion on Airoha EN7581 during probe and suspend/resume to
avoid a hardware defect (Lorenzo Bianconi)
- Enable async probe to reduce system startup time (Douglas Anderson)
* pci/controller/mediatek:
PCI: mediatek-gen3: Enable async probe by default
PCI: mediatek-gen3: Avoid PCIe resetting via PERST# for Airoha EN7581 SoC
PCI: mediatek-gen3: Rely on msleep() in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Move reset delay in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Add comment about initialization order in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Move reset/assert callbacks in .power_up()
PCI: mediatek-gen3: Rely on clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up()
|
|
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_property_read_u32_array() (Krzysztof Kozlowski)
* pci/controller/layerscape:
PCI: layerscape: Use syscon_regmap_lookup_by_phandle_args
|
|
- Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank Li)
- Add DT binding for optional i.MX95 Refclk and driver support to enable it
if the platform hasn't enabled it (Richard Zhu)
- Configure PHY based on controller being in Root Complex or Endpoint mode
(Frank Li)
- Rely on dbi2 and iATU base addresses from DT via dw_pcie_get_resources()
instead of hardcoding them in imx6 (Richard Zhu)
- Skip controller_id computation for i.MX7D since it only has one
controller (Richard Zhu)
- Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
asserted in imx_pcie_assert_core_reset() (Richard Zhu)
- Add missing reference clock enable or disable logic for IMX6SX, IMX7D,
IMX8MM (Richard Zhu)
- Remove redundant imx7d_pcie_init_phy() since imx7d_pcie_enable_ref_clk()
does the same thing (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Clean up comments and whitespace
PCI: imx6: Remove surplus imx7d_pcie_init_phy() function
PCI: imx6: Add missing reference clock disable logic
PCI: imx6: Deassert apps_reset in imx_pcie_deassert_core_reset()
PCI: imx6: Skip controller_id generation logic for i.MX7D
PCI: imx6: Fetch dbi2 and iATU base addesses from DT
PCI: imx6: Configure PHY based on Root Complex or Endpoint mode
PCI: imx6: Add Refclk for i.MX95 PCIe
dt-bindings: PCI: fsl,imx6q-pcie: Add Refclk for i.MX95 RC
PCI: imx6: Add i.MX8Q PCIe Endpoint (EP) support
dt-bindings: PCI: fsl,imx6q-pcie-ep: Add compatible string fsl,imx8q-pcie-ep
# Conflicts:
# drivers/pci/controller/dwc/pci-imx6.c
|
|
- Fix potential string truncation in dw_pcie_edma_irq_verify() (Niklas
Cassel)
- Don't wait for link up in DWC core if driver can detect Link Up event
(Krishna chaitanya chundru)
- If qcom 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya chundru)
- Use dw-rockchip dll_link_up IRQ to detect Link Up and enumerate devices
so users don't have to manually rescan (Niklas Cassel)
- In dw-rockchip, the 'sys' interrupt is required and detects Link Up
events, so tell DWC core not to wait for link up (Niklas Cassel)
- Always stop link in dw_pcie_suspend_noirq(), which is required at least
for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending PME_TURN_OFF
message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add stubs for dw_pcie_suspend_noirq() dw_pcie_resume_noirq() when
CONFIG_PCIE_DW_HOST is not defined so drivers don't need #ifdefs (Bjorn
Helgaas)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add imx6 suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program an
internal Address Translation Unit (iATU) (Frank Li)
* pci/controller/dwc:
PCI: dwc: Simplify config resource lookup
of: address: Add parent_bus_addr to struct of_pci_range
PCI: imx6: Add i.MX8MQ, i.MX8Q and i.MX95 PM support
PCI: imx6: Use DWC common suspend resume method
PCI: dwc: Add dw_pcie_suspend_noirq(), dw_pcie_resume_noirq() stubs for !CONFIG_PCIE_DW_HOST
PCI: dwc: Remove LTSSM state test in dw_pcie_suspend_noirq()
PCI: dwc: Always stop link in the dw_pcie_suspend_noirq
PCI: dw-rockchip: Don't wait for link since we can detect Link Up
PCI: dw-rockchip: Enumerate endpoints based on dll_link_up IRQ
PCI: qcom: Update ICC and OPP values after Link Up event
PCI: qcom: Don't wait for link if we can detect Link Up
PCI: dwc: Don't wait for link up if driver can detect Link Up event
PCI: dwc: Fix potential truncation in dw_pcie_edma_irq_verify()
# Conflicts:
# drivers/pci/controller/dwc/pci-imx6.c
|
|
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
(Krzysztof Kozlowski)
* pci/controller/dra7xx:
PCI: dra7xx: Use syscon_regmap_lookup_by_phandle_args
|
|
- Add host bridge .enable_device() and .disable_device() hooks for bridges
that need to configure things like Requester ID to StreamID mapping when
enabling devices (Frank Li)
- Add imx6 Requester ID to StreamID mapping configuration when enabling
devices (Frank Li)
- Extend struct pci_ecam_ops with .enable_device() and .disable_device()
hooks so drivers that use pci_host_common_probe() instead of their own
.probe() have a way to set the .enable_device() callbacks (Marc Zyngier)
- Convert pcie-apple StreamID mapping configuration from a bus notifier to
the .enable_device() and .disable_device() callbacks (Marc Zyngier)
* pci/controller/iommu-map:
PCI: apple: Convert to {en,dis}able_device() callbacks
PCI: host-generic: Allow {en,dis}able_device() to be provided via pci_ecam_ops
PCI: imx6: Add IOMMU and ITS MSI support for i.MX95
PCI: Add enable_device() and disable_device() callbacks for bridges
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"A pretty quiet cycle this time around. We have a bunch of new Qualcomm
clk drivers, per usual, and then a handful of drivers for other SoCs.
Then the usual pile of cleanups is fairly small data fixes or
converting DT bindings to YAML so they can be validated.
No changes to the core framework besides an OF node refcount bump that
never got decremented.
New Drivers:
- 5L35023 variant of Versa 3 clock generator
- Various Qualcomm clk controllers: IPQ CMN PLL, SM6115 LPASS, SM750
global, tcsr, rpmh, and display. X Plus GPU and global. QCS615 rpmh
and MSM8937 and MSM8940 RPM.
- Qualcomm Pongo and Taycan Alpha PLLs
- Qualcomm IPQ5424 NoC-related interconnect clks
- Renesas RZ/G3E (R9A09G047) SoC clk driver
- SAMA7D65 SoC clk driver
- Samsung Exynos990 SoC clk driver"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (159 commits)
clk: analogbits: Fix incorrect calculation of vco rate delta
clk: bcm: rpi: Add disp clock
clk: bcm: rpi: Create helper to retrieve private data
clk: bcm: rpi: Enable minimize for all firmware clocks
clk: bcm: rpi: Allow cpufreq driver to also adjust gpu clocks
clk: bcm: rpi: Add ISP to exported clocks
clk: stm32f4: support spread spectrum clock generation
clk: stm32f4: use FIELD helpers to access the PLLCFGR fields
dt-bindings: clock: st,stm32-rcc: support spread spectrum clocking
dt-bindings: clock: convert stm32 rcc bindings to json-schema
clk: Use str_enable_disable-like helpers
clk: clk-loongson2: Fix the number count of clk provider
clk: clk-loongson2: Switch to use devm_clk_hw_register_fixed_rate_parent_data()
clk: starfive: Make _clk_get become a common helper function
clk: en7523: Add clock for eMMC for EN7581
dt-bindings: clock: add ID for eMMC for EN7581
dt-bindings: clock: drop NUM_CLOCKS define for EN7581
clk: en7523: Rework clock handling for different clock numbers
clk: thead: Fix cpu2vp_clk for TH1520 AP_SUBSYS clocks
clk: thead: Add CLK_IGNORE_UNUSED to fix TH1520 boot
...
|
|
mode
On Microchip PolarFire SoC the PCIe Root Port can be behind one of three
general purpose Fabric Interface Controller (FIC) buses that encapsulates
an AXI-S bus. Depending on which FIC(s) the Root Port is connected through
to CPU space, and what address translation is done by that FIC, the Root
Port driver's inbound address translation may vary.
For all current supported designs and all future expected designs, inbound
address translation done by a FIC on PolarFire SoC varies depending on
whether PolarFire SoC is operating in coherent DMA mode or noncoherent DMA
mode.
The setup of the outbound address translation tables in the Root Port
driver only needs to handle these two cases.
Setup the inbound address translation tables to one of two address
translations, depending on whether the Root Port is being used with
coherent DMA or noncoherent DMA.
Link: https://lore.kernel.org/r/20241011140043.1250030-3-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f941 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
[bhelgaas: adapt for ac7f53b7e728 ("PCI: microchip: Add support for using
either Root Port 1 or 2")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
If platform_get_resource_byname("config") fails, return error immediately
and unindent the normal path. No functional change intended.
Link: https://lore.kernel.org/r/20250117235119.712043-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
For readability, fix typos and comments that needlessly exceed 80 columns.
Link: https://lore.kernel.org/r/20250118210727.795559-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
Add i.MX8MQ, i.MX8Q and i.MX95 PCIe suspend/resume support.
Link: https://lore.kernel.org/r/20241126075702.4099164-10-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
Call common DWC suspend/resume function. Use DWC common iATU method to
send out PME_TURN_OFF message.
In old DWC implementations, PCIE_ATU_INHIBIT_PAYLOAD in iATU Ctrl2 register
is reserved, so the generic DWC implementation of sending the PME_Turn_Off
message using a dummy MMIO write cannot be used. Use the previous method to
kick off PME_TURN_OFF message for these platforms.
The System Reset Control (SRC) interface is used to toggle 'turnoff_reset'
to send PME_TURN_OFF and since the DWC implementation is used, it is not
needed now.
Replace the imx_pcie_stop_link() and imx_pcie_host_exit() by
dw_pcie_suspend_noirq() in imx_pcie_suspend_noirq().
Since dw_pcie_suspend_noirq() already does these, see below call stack:
dw_pcie_suspend_noirq()
dw_pcie_stop_link()
imx_pcie_stop_link()
pci->pp.ops->deinit()
imx_pcie_host_exit()
Replace the imx_pcie_host_init(), dw_pcie_setup_rc() and
imx_pcie_start_link() by dw_pcie_resume_noirq() in imx_pcie_resume_noirq().
Since dw_pcie_resume_noirq() already does these, see below call stack:
dw_pcie_resume_noirq()
pci->pp.ops->init()
imx_pcie_host_init()
dw_pcie_setup_rc()
dw_pcie_start_link()
imx_pcie_start_link(;
Link: https://lore.kernel.org/r/20241126075702.4099164-9-hongxing.zhu@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
!CONFIG_PCIE_DW_HOST
Previously pcie-designware.h declared dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq() unconditionally, even though they were only
implemented when CONFIG_PCIE_DW_HOST was defined.
Add no-op stubs for them when CONFIG_PCIE_DW_HOST is not defined so
drivers that support both Root Complex and Endpoint modes don't need
Link: https://lore.kernel.org/r/20250117213810.GA656803@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
It's safe to send PME_TURN_OFF message regardless of whether the link is up
or down, so don't test the LTSSM state before sending the PME_TURN_OFF
message.
Only print an error message when the LTSSM is not in DETECT or POLL. There
shouldn't be an error when no Endpoint is connected at all.
Link: https://lore.kernel.org/r/20241210081557.163555-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
On the i.MX8QM, PCIe link can't be re-established again in
dw_pcie_resume_noirq(), if the LTSSM_EN bit is not cleared
properly in dw_pcie_suspend_noirq().
So, add dw_pcie_stop_link() to dw_pcie_suspend_noirq() to fix
this issue and to align the suspend/resume functions since there
is dw_pcie_start_link() in dw_pcie_resume_noirq() already.
Fixes: 4774faf854f5 ("PCI: dwc: Implement generic suspend/resume functionality")
Link: https://lore.kernel.org/r/20241210081557.163555-2-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The Root Complex specific device tree binding for pcie-dw-rockchip has the
'sys' interrupt marked as required.
The driver requests the 'sys' IRQ unconditionally, and errors out if not
provided.
Thus, we can unconditionally set 'use_linkup_irq', so dw_pcie_host_init()
doesn't wait for the link to come up.
This will skip the wait for link up (since the bus will be enumerated once
the link up IRQ is triggered), which reduces the bootup time.
Link: https://lore.kernel.org/r/20250113-rockchip-no-wait-v1-1-25417f37b92f@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Most boards using the pcie-dw-rockchip PCIe controller lack standard
hotplug support.
Thus, when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. This can be avoided by using the
'dll_link_up' interrupt in the combined system interrupt 'sys'.
Once the 'dll_link_up' IRQ is received, the bus underneath the host bridge
is scanned to enumerate PCIe endpoint devices.
This implements the same functionality that was implemented in the DWC
based pcie-qcom driver in 4581403f6792 ("PCI: qcom: Enumerate endpoints
based on Link up event in 'global_irq' interrupt").
The Root Complex specific device tree binding for pcie-dw-rockchip already
has the 'sys' interrupt marked as required, so there is no need to update
the device tree binding. This also means that we can request the 'sys' IRQ
unconditionally.
Link: https://lore.kernel.org/r/20241127145041.3531400-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log, squash Pei Xiao's redundant dev_err() fix from
https://lore.kernel.org/r/327718207d3cd72847c079ff9d56eb246744c182.1736126067.git.xiaopei01@kylinos.cn,
squash Niklas's #define change from https://lore.kernel.org/r/20250103095812.2408364-2-cassel@kernel.org]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
4581403f6792 ("PCI: qcom: Enumerate endpoints based on Link up event in
'global_irq' interrupt") added the Link Up-based enumeration support, but
did not update the ICC/OPP vote once link is up. Before that, the update
happened during probe and the endpoints may or may not be enumerated at
that time, so the ICC/OPP vote was not guaranteed to be accurate.
With Link Up-based enumeration support, the driver can request the accurate
vote based on the PCIe link.
Call qcom_pcie_icc_opp_update() in qcom_pcie_global_irq_thread() after
enumerating the endpoints.
Fixes: 4581403f6792 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-3-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
If we have a 'global' IRQ for Link Up events, we need not wait for the
link to be up during PCI initialization, which reduces startup time.
Check for 'global' IRQ, and if present, set 'use_linkup_irq',
so dw_pcie_host_init() doesn't wait for the link to come up.
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-2-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
If the driver can detect the Link Up event and enumerate downstream devices
at that time, we need not wait here.
Skip waiting for link to come up if the driver supports 'use_linkup_irq'.
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-1-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comment, update commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Increase the size of the string buffer to avoid potential truncation in
dw_pcie_edma_irq_verify().
This fixes the following build warning when compiling with W=1:
drivers/pci/controller/dwc/pcie-designware.c: In function ‘dw_pcie_edma_detect’:
drivers/pci/controller/dwc/pcie-designware.c:989:50: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 3 [-Wformat-truncation=]
989 | snprintf(name, sizeof(name), "dma%d", pci->edma.nr_irqs);
| ^~
Link: https://lore.kernel.org/r/20250104002119.2681246-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Link: https://lore.kernel.org/r/20250112-syscon-phandle-args-pci-v1-1-fcb6ebcc0afc@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
Link: https://lore.kernel.org/r/20250112-syscon-phandle-args-pci-v1-2-fcb6ebcc0afc@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
|
|
This function essentially duplicates imx7d_pcie_enable_ref_clk(). So remove
it.
Link: https://lore.kernel.org/r/20241126075702.4099164-8-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
Ensure the *_enable_ref_clk() function is symmetric by addressing missing
disable parts on some platforms.
Fixes: d0a75c791f98 ("PCI: imx6: Factor out ref clock disable to match enable")
Link: https://lore.kernel.org/r/20241126075702.4099164-7-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
Since the apps_reset is asserted in imx_pcie_assert_core_reset(), it should
be deasserted in imx_pcie_deassert_core_reset().
Fixes: 9b3fe6796d7c ("PCI: imx6: Add code to support i.MX7D")
Link: https://lore.kernel.org/r/20241126075702.4099164-6-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
The i.MX7D only has one PCIe controller, so controller_id should always be
0. The previous code is incorrect although yielding the correct result.
Fix by removing "IMX7D" from the switch case branch.
Fixes: 2d8ed461dbc9 ("PCI: imx6: Add support for i.MX8MQ")
Link: https://lore.kernel.org/r/20241126075702.4099164-5-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
Since dw_pcie_get_resources() gets the dbi2 and iATU base addresses from
DT, remove the code from the imx6 driver that does the same.
Upstream DTSes have not enabled Endpoint function. So nothing is broken for
old upstream DTBs.
Link: https://lore.kernel.org/r/20241126075702.4099164-4-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Pass PHY_MODE_PCIE_EP if the PCI controller operates in Endpoint (EP) mode,
and fix the Root Complex (RC) mode being hardcoded using a drvdata mode
check.
Fixes: 8026f2d8e8a9 ("PCI: imx6: Call common PHY API to set mode, speed, and submode")
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-6-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
|
|
Add "ref" clock to enable Refclk. To avoid breaking DT backwards
compatibility, the i.MX95 "ref" clock is optional. Use
devm_clk_get_optional() to fetch i.MX95 PCIe optional clocks in driver.
If using external clock, "ref" clock should point to external reference.
If using internal clock, CREF_EN in LAST_TO_REG controls reference output,
implemented in drivers/clk/imx/clk-imx95-blk-ctl.c.
Link: https://lore.kernel.org/r/20241126075702.4099164-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
