| Age | Commit message (Collapse) | Author |
|---|
|
Add NO_EINT_SUPPORT back to pinctrl-mtk-common-v2.h as the alias of
EINT_NA to indicate that some pin not capable of being controlled as eint
and that is required by pinctrl-paris based driver as old
pinctrl-mtk-common.h already had.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
EINT_NA is an u16 number, so it should be U16_MAX instead of -1
to fix up drivers/pinctrl/mediatek/pinctrl-paris.c:732 mtk_gpio_to_irq()
warn: impossible condition (desc->eint.eint_n == -1) => (0-u16max == (-1))
Also happens in
drivers/pinctrl/mediatek/pinctrl-paris.c:749 mtk_gpio_set_config()
warn: impossible condition (desc->eint.eint_n == -1) => (0-u16max == (-1))
drivers/pinctrl/mediatek/pinctrl-moore.c:479 mtk_gpio_to_irq()
warn: impossible condition (desc->eint.eint_n == -1) => (0-u16max == (-1))
drivers/pinctrl/mediatek/pinctrl-moore.c:496 mtk_gpio_set_config()
warn: impossible condition '(desc->eint.eint_n == -1) => (0-u16max == (-1))
Fixes: 6561859b067f ("pinctrl: mediatek: add eint support to MT8183 pinctrl driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In case of error, the function devm_kmalloc_array() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: b7d7f9eeca55 ("pinctrl: mediatek: extend struct mtk_pin_desc which per-pin driver depends on")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fixes the following sparse warning:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c:37:29: warning:
symbol 'mtk_drive' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In case of error, the function devm_kmalloc_array() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 805250982bb5 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
'ret' should be returned while pmic_mpp_write_mode_ctl fails.
Fixes: 0e948042c420 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
No user of mxs_pinctrl_probe() can be built as a module, hence
exporting the symbol is not necessary. Drop EXPORT_SYMBOL_GPL.
Inspired by a patch from Stefan Agner for the tegra pinctrl driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For some reason I thought GPIOLIB handles translation from GPIO ranges
to pinctrl pins but it turns out not to be the case. This means that
when GPIOs operations are performed for a pin controller having a custom
GPIO base such as Cannon Lake and Ice Lake incorrect pin number gets
used internally.
Fix this in the same way we did for lock/unlock IRQ operations and
translate the GPIO number to pin before using it.
Fixes: a60eac3239f0 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Reported-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
No user of tegra_pinctrl_probe can be built as a module, hence
exporting the symbol is not necessary. Drop EXPORT_SYMBOL_GPL.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add USB[01] pin groups and functions to the R8A77470 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add SDHI2 pin groups and functions to the R8A77470 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add QSPI0 pin groups and function to the R8A77470 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add DU0 pin groups and function to the R8A77470 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add I2C4 pin groups and function to the R8A77470 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Renesas RZ/G2E (a.k.a. r8a774c0) is pin compatible with R-Car
E3 (a.k.a. r8a77990), however it doesn't have several automotive
specific peripherals. Add a r8a77990 specific pin groups/functions
along with common pin groups/functions for supporting both r8a77990
and r8a774c0 SoCs.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Renesas RZ/G1N (R8A7744) is pin compatible with R-Car M2-W/N (R8A7791/3)
and RZ/G1M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Include only <linux/gpio/driver.h> since this is a driver,
not a consumer.
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Compiler unsatisfied to see half described data structures
and issues warnings:
drivers/pinctrl/intel/pinctrl-cherryview.c:136: warning: Function parameter or member 'acpi_space_id' not described in 'chv_community'
drivers/pinctrl/intel/pinctrl-cherryview.c:169: warning: Function parameter or member 'saved_intmask' not described in 'chv_pinctrl'
drivers/pinctrl/intel/pinctrl-cherryview.c:169: warning: Function parameter or member 'saved_pin_context' not described in 'chv_pinctrl'
To satisfy it, describe mentioned members.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For the long time no one complained about unused groups of pins
for fSPI and SMBUS.
Remove them for good and at the same time satisfy compiler,
otherwise get warning:
CC drivers/pinctrl/intel/pinctrl-cherryview.o
drivers/pinctrl/intel/pinctrl-cherryview.c:285:23: warning: ‘southwest_smbus_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned southwest_smbus_pins[] = { 79, 81, 82 };
^~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/intel/pinctrl-cherryview.c:269:23: warning: ‘southwest_fspi_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned southwest_fspi_pins[] = { 0, 1, 2, 3, 4, 5, 6, 7 };
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Sort header block alphabetically for easy maintenance.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since the driver can't be compiled as a module, there is no need
to use no-op macros in the code.
Thus, remove unneeded MODULE_DEVICE_TABLE() macro from the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We now using a common macro for PM operations in pin control drivers for Intel
SoCs, and since that macro relies on the definition and macro from linux/pm.h
header file, it's logical to include it directly in pinctrl-intel.h. Otherwise
it's a bit fragile and requires a proper ordering of header inclusion in C
files.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio base for GPP-E was set incorrectly to 258 instead of 256,
preventing the touchpad working on my Tong Fang GK5CN5Z laptop.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=200787
Signed-off-by: Simon Detheridge <s@sd.ai>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
Just add eint support to MT8183 pinctrl driver as usual as
happens on the other SoCs.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Almost all MediaTek SoCs apply the exact same logic to build eint, so move
the common functions into pinctrl-mtk-common-v2.c to allow each new pinctrl
driver to reuse them. Also, add a protection checker on hw->soc->eint_hw to
avoid invalid memory access when there's certain SoC not to define its
eint_hw properly in the code flow.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch provides the advanced pull for I2C used pins on MT8183.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Extend the advanced pull based on the legacy bias plus additional r0 and r1
to tweak the resistor level.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add MT8183 pinctrl driver based on MediaTek pinctrl-paris core.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add pinctrl-paris core that implements vendor dt-binding which MediaTek
tablet, box and smartphone-based SoCs such as MT81xx, MT27xx, and MT67xx
SoCs really want to depend on. The driver is just completely rewritten
according to pinctrl-mtk-common.c but uses the new logic from
pinctrl-mtk-common-v2.c to have an elegant way to support new SoCs in the
future.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Because the pincrl-mtk-common.c is an implementation for per-pin binding,
its pin descriptor includes more information than pinctrl-mtk-common-v2
so far can support. So, we complement these data before writing a driver
using pincrl-mtk-common-v2.c for per-pin binding. By the way, the size of
struct mtk_pin_desc would be larger than struct pinctrl_pin_desc can hold,
so it's necessary to have a copy before the pins information is being
registered into the core.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
supported is found
It's usual and not an error for there's some register not supported by a
certain SoC or a pin so that in the case we have to adjust the message to
print and the error code to get rid of unnecessary false alarm.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinctrl-mtk-common-v2.c
Certain SoC own multiple register base for accessing each pin groups,
it's easy to be done with extend struct mtk_pin_field_calc to support
the kind of SoC such as MT8183.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
all use pin descriptor instead in pinctrl-mtk-common-v2.c for the
consistency and extensibility.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Adding MT7623 pinctrl driver based on generic pinctrl binding, that is
good example and demonstrates how to port any other MediaTek SoCs
pinctrl-moore core when people really would like to use the generic
pinctrl binding to support these MediaTek SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinctrl-mtk-common-v2.c
Certain SoCs have to program an extra PULLEN, PULLSEL register to configure
bias related function so that we add it in the existing path.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Certain SoCs have to program an extra IES register to configure input
enabled mode so that we add it in the existing path as an option.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There are some specific pins (i.e. MMC/SD) need specific registers to
turn on/off the 10K & 50k(75K) resistors when pull up/down.
Therefore, this patch adds the custom prarmeters so that the user could
control it through device tree.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Put pull control support related functions to pinctrl-mtk-common-v2.c
as these operations might be different by chips and allow different
type of driver to reuse them.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Certain SoCs have to program DRV register to configure driving
strength so that we add it in the existing path as an option.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinctrl-mtk-common-v2.c
Put driving strength support related functions to pinctrl-mtk-common-v2.c
as these operations might be different by chips and allow different type
of driver to reuse them.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add two parameters gpio_m and eint_m for configuring GPIO mode and EINT
mode, they might be varying depend on SoC.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch introduces a data structure mtk_pin_desc, which is used to
provide information per pin characteristic such as driving current,
eint number and a driving index, that is used to lookup table describing
the details about the groups of driving current by which the pin is able
to adjust the driving strength so that the driver could get the
appropriate driving group when calls .pin_config_get()/set().
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds members sz_reg fixed in struct mtk_pin_field_calc
- The 'fixed' is used to represent the consecutive pins share the same
bits within the same register with the 1st pin so that it can largely
reduce the entry size a bit.
- The 'sz_reg' is used to indicate the range of bits we use in a register
that may vary by SoC
The above changes make the code more generic and this is useful as there
might be other existing or future chips all use the same logic to access
their register set and then being a little more abstract could help in the
long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
dt-bindings
Add a generic driver pinctrl-moore.c for MT762x SoC and any other SoC
that would like to use generic dt-binding. The patch is furtherly
refactored from pinctrl-mt7622.c that totally uses the functions back by
the generic pinctrl core such as GENERIC_PINCONF, GENERIC_PINCTRL_GROUPS,
and GENERIC_PINMUX_FUNCTIONS and its binding also completely follows up
pinctrl-bindings.txt in Documentation/devicetree/bindings/pinctrl/ to
implement.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Irregular register arrangement and distinct logic access from various
MediaTek SoCs would cause pinctrl-mtk-common to bloat and really hard to
maintain in the future so that the patch creates pinctrl-mtk-common-v2
based on the core of mt7622-pinctrl.
The goals pinctrl-mtk-common-v2 want to achieve are to hopefully support
all of MediaTek SoCs, and two kinds of dt-bindings being supported,
Linux generic pinctrl dt-binding mt7622 supports and MediaTek per-pin
dt-binding the other SoCs support the MT8183 and MT6765 incline to make
use of.
The patch starts to refactor MT7622 pinctrl driver first with splitting
out these portable ways from there such as table-based register operation
and drive strength control that is common in both kinds of driver.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
By just moving the atmel_gpio_to_irq() and calling the internal
function we can get rid of the driver calling back out into the
deprecated external consumer API.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
