summaryrefslogtreecommitdiff
path: root/drivers/power
AgeCommit message (Collapse)Author
2021-03-22power: supply: max1721x: Correct spellingXiaofeng Cao
Change 'stanalone' to 'standalone' Change 'mesaurement' to 'measurement' Change 'nonvilatile' to 'nonvolatile' Change 'unical' to 'unique' Change 'unaccesable' to 'unaccessible' Change 'correcpondent' to 'correspond' Signed-off-by: Xiaofeng Cao <caoxiaofeng@yulong.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-22power: supply: ds2781: use kobj_to_dev()dongjian
Use kobj_to_dev() instead of open-coding it Signed-off-by: dongjian <dongjian@yulong.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-22power: supply: charger-manager: Fix a typoBhaskar Chowdhury
s/systme/system/ Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-22power: reset: remove unneeded semicolondongjian
Fixes coccicheck warning: drivers/power/reset/vexpress-poweroff.c:136:2-3: Unneeded semicolon Signed-off-by: dongjian <dongjian@yulong.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-22power: supply: Use IRQF_ONESHOTdongjian
Fixes coccicheck error: drivers/power/supply/pm2301_charger.c:1089:7-27: ERROR: drivers/power/supply/lp8788-charger.c:502:8-28: ERROR: drivers/power/supply/tps65217_charger.c:239:8-33: ERROR: drivers/power/supply/tps65090-charger.c:303:8-33: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT Signed-off-by: dongjian <dongjian@yulong.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-21power: supply: bq27xxx: Add support for BQ78Z100LI Qingwu
Add support for TI BQ78Z100, I2C interface gas gauge. It provides a fully integrated safety protection and authentication for 1 to 2-series cell Li-Ion and Li-Polymer battery packs. The patch was tested with BQ78Z100 equipment. CASE I: Discharging: POWER_SUPPLY_NAME=bq78z100-0 POWER_SUPPLY_STATUS=Discharging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_VOLTAGE_NOW=3386000 POWER_SUPPLY_CURRENT_NOW=-5000 POWER_SUPPLY_CAPACITY=27 POWER_SUPPLY_CAPACITY_LEVEL=Normal POWER_SUPPLY_TEMP=269 POWER_SUPPLY_TIME_TO_EMPTY_NOW=1249920 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CHARGE_FULL=6494000 POWER_SUPPLY_CHARGE_NOW=1736000 POWER_SUPPLY_CHARGE_FULL_DESIGN=6000000 POWER_SUPPLY_CYCLE_COUNT=1 POWER_SUPPLY_POWER_AVG=-20000 POWER_SUPPLY_HEALTH=Good POWER_SUPPLY_MANUFACTURER=Texas Instruments CASE II : No discharging current: POWER_SUPPLY_NAME=bq78z100-0 POWER_SUPPLY_STATUS=Not charging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_VOLTAGE_NOW=3386000 POWER_SUPPLY_CURRENT_NOW=0 POWER_SUPPLY_CAPACITY=27 POWER_SUPPLY_CAPACITY_LEVEL=Normal POWER_SUPPLY_TEMP=270 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CHARGE_FULL=6494000 POWER_SUPPLY_CHARGE_NOW=1734000 POWER_SUPPLY_CHARGE_FULL_DESIGN=6000000 POWER_SUPPLY_CYCLE_COUNT=1 POWER_SUPPLY_POWER_AVG=0 POWER_SUPPLY_HEALTH=Good POWER_SUPPLY_MANUFACTURER=Texas Instruments Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-15power: supply: bq27xxx: make status more robustMatthias Schiffer
There are multiple issues in bq27xxx_battery_status(): - On BQ28Q610 is was observed that the "full" flag may be set even while the battery is charging or discharging. With the current logic to make "full" override everything else, it look a very long time (>20min) for the status to change from "full" to "discharging" after unplugging the supply on a device with low power consumption - The POWER_SUPPLY_STATUS_NOT_CHARGING check depends on power_supply_am_i_supplied(), which will not work when the supply doesn't exist as a separate device known to Linux We can solve both issues by deriving the status from the current instead of the flags field. The flags are now only used to distinguish "full" from "not charging", and to determine the sign of the current on BQ27XXX_O_ZERO devices. Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-15power: supply: bq27xxx: fix power_avg for newer ICsMatthias Schiffer
On all newer bq27xxx ICs, the AveragePower register contains a signed value; in addition to handling the raw value as unsigned, the driver code also didn't convert it to µW as expected. At least for the BQ28Z610, the reference manual incorrectly states that the value is in units of 1mW and not 10mW. I have no way of knowing whether the manuals of other supported ICs contain the same error, or if there are models that actually use 1mW. At least, the new code shouldn't be *less* correct than the old version for any device. power_avg is removed from the cache structure, se we don't have to extend it to store both a signed value and an error code. Always getting an up-to-date value may be desirable anyways, as it avoids inconsistent current and power readings when switching between charging and discharging. Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-15power: supply: bq27xxx: fix sign of current_now for newer ICsMatthias Schiffer
Commit cd060b4d0868 ("power: supply: bq27xxx: fix polarity of current_now") changed the sign of current_now for all bq27xxx variants, but on BQ28Z610 I'm now seeing negated values *with* that patch. The GTA04/Openmoko device that was used for testing uses a BQ27000 or BQ27010 IC, so I assume only the BQ27XXX_O_ZERO code path was incorrect. Revert the behaviour for newer ICs. Fixes: cd060b4d0868 "power: supply: bq27xxx: fix polarity of current_now" Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-15power: supply: axp20x_usb_power: Add missing check in axp20x_usb_power_probeDinghao Liu
There are two regmap_update_bits() calls but only one of them has return value check, which is odd. Add a return value check and terminate the execution flow on failure just like the other call. Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-15power: supply: z2_battery: Drop unused variableLinus Walleij
The kernel test robot reports an unused variable in the Z2 battery code caused by a recent commit. Fixes: a3b4388ea19b ("power: supply: z2_battery: Convert to GPIO descriptors") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-06power: supply: smb347-charger: Clean up whitespaces in the codeDmitry Osipenko
Improve formatting of the code by removing unnecessary whitespaces. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-06power: supply: smb347-charger: Improve interrupt initializationDmitry Osipenko
A previous commit attempted to fix IRQ usage in a case where interrupt is failed to initialize, but it missed couple more cases that could be improved. The interrupt could be undefined and then everything related to interrupt shouldn't be touched by driver. Secondly, we shouldn't ignore errors that aren't directly related to enabling interrupt in hardware, like enabling h/w write-access or requesting interrupt. Improve interrupt initialization in the driver in order to handle the missing cases. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-06power: supply: s3c_adc_battery: remove unused pdata in suspend/resumeKrzysztof Kozlowski
The "pdata" local variable is not used in suspend/resume handlers since commit 7776bcd241e0 ("power: supply: s3c-adc-battery: Convert to GPIO descriptors"): drivers/power/supply/s3c_adc_battery.c: In function ‘s3c_adc_bat_suspend’: drivers/power/supply/s3c_adc_battery.c:405:28: warning: unused variable ‘pdata’ [-Wunused-variable] drivers/power/supply/s3c_adc_battery.c: In function ‘s3c_adc_bat_resume’: drivers/power/supply/s3c_adc_battery.c:422:28: warning: unused variable ‘pdata’ [-Wunused-variable] Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-06power: supply: s3c_adc_battery: add SPDX license identifierKrzysztof Kozlowski
Add SPDX license identifier and replace license boilerplate. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-06power: supply: cw2015: Add CHARGE_NOW supportMartin Ashby
CHARGE_NOW is expected by some user software (such as waybar) instead of 'CAPACITY', in order to correctly calculate remaining battery life. Signed-off-by: Martin Ashby <martin@ashbysoft.com> Reviewed-by: Tobias Schramm <t.schramm@manjaro.org> Tested-by: Tobias Schramm <t.schramm@manjaro.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-03-06power: supply: max8997-charger: remove unneeded semicolonJiapeng Chong
Fix the following coccicheck warnings: ./drivers/power/supply/max8997_charger.c:266:3-4: Unneeded semicolon. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-28power-supply: use kobj_to_dev()Jian Dong
Use kobj_to_dev() instead of open-coding it Signed-off-by: Jian Dong <dongjian@yulong.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-25power: supply: charger-manager: fix typoJunlin Yang
Change 'exeeds' to 'exceeds'. Signed-off-by: Junlin Yang <yangjunlin@yulong.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-25power/reset: remove zte zx driverArnd Bergmann
The zte zx platform is getting removed, so this driver is no longer needed. Cc: Jun Nie <jun.nie@linaro.org> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-25power: supply: bq25980: Fix repetive bq25975 with bq25960xinjian
The i2c_device_id bq25975 is repeated, and should be bq25960. Signed-off-by: xinjian <xinjian@yulong.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-25power: supply: smb347-charger: Fix interrupt usage if interrupt is unavailableDmitry Osipenko
The IRQ=0 could be a valid interrupt number in kernel because interrupt numbers are virtual in a modern kernel. Hence fix the interrupt usage in a case if interrupt is unavailable by not overriding the interrupt number which is used by the driver. Note that currently Nexus 7 is the only know device which uses SMB347 kernel diver and it has a properly working interrupt, hence this patch doesn't fix any real problems, it's a minor cleanup/improvement. Fixes: 99298de5df92 ("power: supply: smb347-charger: Replace mutex with IRQ disable/enable") Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-25power: supply: axp20x_usb_power: Init work before enabling IRQsSamuel Holland
The IRQ handler calls mod_delayed_work() on power->vbus_detect. However, that work item is not initialized until after the IRQs are enabled. If an IRQ is already pending when the driver is probed, the driver calls mod_delayed_work() on an uninitialized work item, which causes an oops. Fixes: bcfb7ae3f50b ("power: supply: axp20x_usb_power: Only poll while offline") Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-17power: supply: fix sbs-charger build, needs REGMAP_I2CRandy Dunlap
CHARGER_SBS should select REGMAP_I2C since it uses API(s) that are provided by that Kconfig symbol. Fixes these errors: ../drivers/power/supply/sbs-charger.c:149:21: error: variable ‘sbs_regmap’ has initializer but incomplete type static const struct regmap_config sbs_regmap = { ../drivers/power/supply/sbs-charger.c:150:3: error: ‘const struct regmap_config’ has no member named ‘reg_bits’ .reg_bits = 8, ../drivers/power/supply/sbs-charger.c:155:23: error: ‘REGMAP_ENDIAN_LITTLE’ undeclared here (not in a function) .val_format_endian = REGMAP_ENDIAN_LITTLE, /* since based on SMBus */ ../drivers/power/supply/sbs-charger.c: In function ‘sbs_probe’: ../drivers/power/supply/sbs-charger.c:183:17: error: implicit declaration of function ‘devm_regmap_init_i2c’; did you mean ‘devm_request_irq’? [-Werror=implicit-function-declaration] chip->regmap = devm_regmap_init_i2c(client, &sbs_regmap); ../drivers/power/supply/sbs-charger.c: At top level: ../drivers/power/supply/sbs-charger.c:149:35: error: storage size of ‘sbs_regmap’ isn’t known static const struct regmap_config sbs_regmap = { Fixes: feb583e37f8a ("power: supply: add sbs-charger driver") Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-16power: supply: bq27xxx: fix polarity of current_nowAndreas Kemnade
current_now has to be negative during discharging and positive during charging, the behavior seen is the other way round. Tested on GTA04 with Openmoko battery. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-16power: supply: charger-manager: fix incorrect health statusJunlin Yang
cm->emergency_stop will only be the value in the enumeration, and cannot be less than zero, it will get an exception value. So replace it with the corresponding value. Signed-off-by: Junlin Yang <yangjunlin@yulong.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-16power: reset: at91-sama5d2_shdwc: add support for sama7g5Claudiu Beznea
Add support for SAMA7G5 by adding proper struct reg_config structure and since SAMA7G5 is not currently on LPDDR setups the commit also avoid the mapping of DDR controller. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-16power: reset: at91-sama5d2_shdwc: fix wkupdbc maskClaudiu Beznea
According to datasheet WKUPDBC mask is b/w bits 26..24. Fixes: f80cb48843987 ("power: reset: at91-shdwc: add new shutdown controller driver") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-16power: supply: bq24190_charger: convert comma to semicolonZheng Yongjun
Replace a comma between expression statements by a semicolon. Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-16power: supply: ab8500_fg: convert comma to semicolonZheng Yongjun
Replace a comma between expression statements by a semicolon. Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-16power: supply: ds2780: Switch to using the new API kobj_to_dev()Tian Tao
fixed the following coccicheck: drivers/power/supply/ds2780_battery.c:627:60-61: WARNING opportunity for kobj_to_dev() drivers/power/supply/ds2780_battery.c:672:60-61: WARNING opportunity for kobj_to_dev() drivers/power/supply/ds2780_battery.c:640:60-61: WARNING opportunity for kobj_to_dev() drivers/power/supply/ds2780_battery.c:685:60-61: WARNING opportunity for kobj_to_dev() Signed-off-by: Tian Tao <tiantao6@hisilicon.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-16power: supply: bq27xxx: Support CHARGE_NOW for bq27z561/bq28z610/bq34z100Hermes Zhang
Currently REG_NAC (nominal available capacity) is mapped to power-supply's CHARGE_NOW property. Some chips do not have REG_NAC and do not expose CHARGE_NOW at the moment. Some bq27xxx chips also have another register REG_RM (remaining capacity). The difference between REG_NAC and REG_RM is load compensation. This patch adds register information for REG_RM for all supported fuel gauges. On systems having REG_NAC it is ignored, so behaviour does not change. On systems without REG_NAC, REG_RM will be used to provide CHARGE_NOW functionality. As a result there are three more chips exposing CHARGE_NOW: bq27z561, bq28z610 and bq34z100 Signed-off-by: Hermes Zhang <chenhuiz@axis.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-15power: supply: cpcap-charger: Fix power_supply_put on null battery pointerColin Ian King
Currently if the pointer battery is null there is a null pointer dereference on the call to power_supply_put. Fix this by only performing the put if battery is not null. Addresses-Coverity: ("Dereference after null check") Fixes: 4bff91bb3231 ("power: supply: cpcap-charger: Fix missing power_supply_put()") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-15power: supply: cpcap-battery: constify psy_descSebastian Reichel
There is no dynamic information in cpcap-battery's power-supply description struct, so let's make it static const. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Acked-by: Pavel Machek <pavel@ucw.cz> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-battery: Fix typoPavel Machek
Fix typo Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Pavel Machek <pavel@ucw.cz> [tony@atomide.com: separated out from charger changes] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-battery: Add charge_now propertyArthur Demchenkov
Add charge_now property for capacity reporting. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com> [tony@atomide.com: updated to apply for naming changes] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-battery: Implement capacity reportingArthur Demchenkov
Calculate percentage using charge_full value provided. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com> [tony@atomide.com: updated to apply after dropping my earlier patch] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-battery: Keep track of state for capacity reportingArthur Demchenkov
Save the battery empty and full states so we can use those to estimate the battery capacity in the following patches. If the user provides us with charge_full value (which it could save in a permanent storage between reboots), initialize low and high counter_uah with calculated values. If we hit battery low once, we should stick on reporting it until the charger is connected. This way low->counter_uah will be updated properly, and that will allow us to get more accurate charge_full value. Based on an earlier patch by Tony Lindgren with charge_full usage and other improvments done by Arthur Demchenkov. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Co-developed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com> [tony@atomide.com: combined earlier patches, updated comments] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-battery: Add charge_full propertyArthur Demchenkov
Add charge_full property and let user update it. This is needed for capacity reporting in the following patches. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com> [tony@atomide.com: updated comments] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-battery: Use charger status for battery full detectionTony Lindgren
We now get battery full notification from cpcap-charger, so let's use that for battery full status and charger disconnect. Note that any current based battery full detection we have tried earlier is flakey as it won't account for example for CPU load increasing the battery current. Anyways, if current based battery full detection is also still needed, we can reconsider adding it in addition to the charger status based detection. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-charger: Provide state updates for battery from chargerTony Lindgren
We want to have the battery update it's status when the charge is done, and when the charger is disconnected. Otherwise the battery does not know when it's full unless there's a userspace app polling the battery status. To do this, we add supplied_to handling to cpcap-battery, and implement power_supply_changed() for cpcap-charger. When cpcap-charger calls power_supply_changed(), cpcap-battery will update it's status. Let's also use new_state variable for the POWER_SUPPLY_STATUS_CHARGING case to have unified handling for the switch. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-charger: Simplify things with enable and disableTony Lindgren
Let's turn cpcap_charger_set_state() into separate cpcap_charger_enable() and cpcap_charger_disable() to simplify things, and to allow managing status separately. This can be then used for the follow-up patches to make battery full status behave a bit nicer. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-charger: Drop internal state and use generic statsTony Lindgren
We currently have both state and status, get rid of state and use generic status instead. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-charger: Limiting charge current on Droid 4Pavel Machek
Droid 4 has same problem as N900: it is often necessary to manually tweak current draw from USB, for example when using thin charging cable. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Pavel Machek <pavel@ucw.cz> [tony@atomide.com: rebased, cleaned up whitespace issues, updated comments] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-charger: Use standard enumerationTony Lindgren
Just get rid of the custom enumeration if favor of the standard one. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-charger: Make VBUS already provided debug onlyTony Lindgren
This should be only shown when debug is enabled. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-charger: Fix flakey reboot with charger connectedTony Lindgren
If we have a USB charger connected, reboot is flakey and often fails to reboot the device with the charger LED staying on. Let's fix this by implementing .shutdown. Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-battery: Fix missing power_supply_put()Tony Lindgren
Fix missing power_supply_put(). Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Fixes: 8b0134cc14b9 ("power: supply: cpcap-battery: Fix handling of lowered charger voltage") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: cpcap-charger: Fix missing power_supply_put()Tony Lindgren
Fix missing power_supply_put(). Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Fixes: 5688ea049233 ("power: supply: cpcap-charger: Allow changing constant charge voltage") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-01-14power: supply: Add battery gauge driver for Acer Iconia Tab A500Dmitry Osipenko
This patch adds battery gauge driver for Acer Iconia Tab A500 device. The battery gauge function is provided via the Embedded Controller, which is found on the Acer A500. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
generated by cgit (git 2.34.1) at 2025-09-11 22:54:14 +0000