| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The regulator_linear_range arrays and stpmic1_regulator_cfgs are only
accessed by this driver and the values are never changed so make them
static const. regulator_ops variables can also be const.
Also clean up a few empty lines in regulator_linear_range array.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
BD70528MWV is an ultra-low Iq general purpose single-chip power
management IC for battery-powered portable devices.
Add support for controlling 3 bucks and 3 LDOs present in
ROHM BD70528.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In some scenarios the early stages of the boot chain has configured
regulators to be in a required state, but the later stages has skipped
to inform the RPM about it's requirements.
But as the SMD RPM regulators are being initialized voltage change
requests will be issued to align the voltage with the valid ranges. The
RPM aggregates all parameters for the specific regulator, the voltage
will be adjusted and the "enabled" state will be "off" - and the
regulator is turned off.
This patch addresses this problem by caching the requested enable state,
voltage and load and send the parameters in a batch, depending on the
enable state - effectively delaying the voltage request for disabled
regulators.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the missing MODULE_DEVICE_TABLE and remove the comma from the
separator on the end of the of_device_id array.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The act8600_sudcdc_voltage_ranges setting does not match the datasheet.
The problems in below entry:
REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000),
1. The off-by-one min_sel causes wrong volatage calculation.
The min_sel should be 192.
2. According to the datasheet[1] Table 7. (on page 43):
The selector 248 (0b11111000) ~ 255 (0b11111111) are 41.400V.
Also fix off-by-one for ACT8600_SUDCDC_VOLTAGE_NUM.
[1] https://active-semi.com/wp-content/uploads/ACT8600_Datasheet.pdf
Fixes: df3a950e4e73 ("regulator: act8865: Add act8600 support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The modalias is set by the MODULE_DEVICE_TABLE, thus remove redundant
MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Having instance specific copy of desc is enough to support multiple
instance of pwm regulator.
The regulator_ops is never changed so no need to copy it per instance, make
pwm_regulator_voltage_table_ops and pwm_regulator_voltage_continuous_ops
const to ensure they won't be changed.
The pwm_regulator_desc is a template to be copied so also make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ctrl_regs field is not used at all, remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If regulator DT node doesn't exist, its of_parse_cb callback
function isn't called. Then all values for DT properties are
filled with zero. This leads to wrong register update for
FPS and POK settings.
Signed-off-by: Jinyoung Park <jinyoungp@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Provide a helper allowing to access regulator's regmap.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently rdev is dereferenced when assigning desc before rdev is null
checked, hence there is a potential null pointer dereference on rdev.
Fix this by null checking rdev first.
Detected by CoverityScan, CID#1476031 ("Dereference before null check")
Fixes: 77e3e3b165db ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix few trivial language typos in core and drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use rdev_get_id() instead of directly access rdev->desc->id.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current implementation missed the case BCM590XX_REG_VSR, so
bcm590xx_get_enable_register() returns 0 when id is BCM590XX_REG_VSR.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
Fix trival copy-n-paste mistake.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
tps65910_reg_set_bits() may fail. The fix checks if it fails, and if so,
returns with its error code.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix build error when CONFIG_REGMAP_I2C=m && CONFIG_REGULATOR_MCP16502=y.
drivers/regulator/mcp16502.o: In function `mcp16502_probe':
mcp16502.c:(.text+0xca): undefined reference to `__devm_regmap_init_i2c'
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The n_voltages setting is not set, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
mcp16502_suspend/resume_noirq
mcp16502_suspend/resume_noirq is only used by SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
when CONFIG_PM_SLEEP is defined.
So use #ifdef CONFIG_PM_SLEEP instead CONFIG_SUSPEND guard.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch does the following:
- align parameter with parenthesis
- fix compile error
If CONFIG_SUSPEND is not set the dummy pm_ops
callbacks are named mcp16502_suspend and mcp16502_resume
instead of mcp16502_suspend_noirq and mcp16502_resume_noirq.
Excerpt from compile log (kbuild test robot):
In file included from include/linux/device.h:23:0,
from include/linux/gpio/driver.h:5,
from include/asm-generic/gpio.h:13,
from include/linux/gpio.h:62,
from drivers/regulator/mcp16502.c:11:
>> drivers/regulator/mcp16502.c:527:32: error: 'mcp16502_suspend_noirq'
undeclared here (not in a function); did you mean 'mcp16502_suspend'?
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq,
>> drivers/regulator/mcp16502.c:528:10: error: 'mcp16502_resume_noirq'
undeclared here (not in a function); did you mean 'mcp16502_suspend_noirq'?
mcp16502_resume_noirq)
vim +527 drivers/regulator/mcp16502.c
524
525 #ifdef CONFIG_PM
526 static const struct dev_pm_ops mcp16502_pm_ops = {
> 527 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq,
> 528 mcp16502_resume_noirq)
529 };
530 #endif
531 static const struct i2c_device_id mcp16502_i2c_id[] = {
532 { "mcp16502", 0 },
533 { }
534 };
535 MODULE_DEVICE_TABLE(i2c, mcp16502_i2c_id);
536
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes the following sparse warning:
drivers/regulator/act8945a-regulator.c:340:1: warning:
symbol 'act8945a_pm' was not declared. Should it be static?
Fixes: 7482d6ecc68e ("regulator: act8945a-regulator: Implement PM functionalities")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If palmas_smps_read() fails, we should not use the read data in "reg"
which may contain random value. The fix inserts a check for the return
value of palmas_smps_read(): If it fails, we return the error code
upstream and stop using "reg".
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix 'defined but not used' compiler warning for act8945a_suspend()
function in case CONFIG_PM_SLEEP is not defined.
Fixes: b5ebba46e694 ("regulator: act8945a-regulator: add shutdown function")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reported-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Initial commit of set_ramp_delay feature was missing an assignment which
should have populated slew_rate table for dcdc2 regulator. Add it.
Fixes: d29f54df8b16 ("regulator: axp20x: add support for set_ramp_delay for AXP209")
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds support for entering/resuming suspend states.
It does this by setting the LPM pin of the PMIC.
When suspending the PMIC will enter the Low-power mode
when the LPM pin will be set to high. If the suspend target state
is suspend-to-mem, the PMIC will transition to Hibernate mode,
otherwise, if it is standby, it will remain in Low-power mode.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, we use the soft-start constraint of the regulator
node to first bring up the LDO3 to the lowest possible voltage and
then enable the LDO. After that, we can set the requested voltage
as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
enable voltage slowly and staggered, potentially reducing overall
inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3.
This patch adds preliminary support for the regulator-ramp-delay property
for these 2 regulators. Note that the voltage ramp only works when
regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-4.21
|
|
This patch adds a regulator driver for the MCP16502 PMIC.
This drivers supports basic operations through the
regulator interface such as:
- setting/reading voltage
- setting/reading operating mode
- reading current status
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Implement shutdown method to make sure the PMIC will not enter the suspend
state when the system is shutdown.
This work is based on work done by Borris Brezillon on [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix line over 80 chars checkpatch.pl warning.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The regulator supports a dedicated suspend mode.
Implement the appropriate ->set_suspend_xx() hooks, add support for
->set_mode(), and provide basic PM ops functionalities to setup the
regulator in a suspend state when the system is entering suspend.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[claudiu.beznea@microchip.com: remove shutdown function, use dev_pm_ops,
fix checkpatch warning, adapt commit message, add LDO modes support,
move modes constants to active-semi,8945a-regulator.h, remove rdevs from
struct act8945a_pmic, add op_mode to act8945a_pmic]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Unlock expert registers for act8945a.
This is based on orginal work of Boris Brezillon at [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the Arizona LDO1 driver becomes
redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the wm8994 driver becomes redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
At the end of regulator_resolve_supply() we have historically turned
on our supply in some cases. This could be for one of two reasons:
1. If resolving supplies was happening before the call to
set_machine_constraints() we needed to predict if
set_machine_constraints() was going to turn the regulator on and we
needed to preemptively turn the supply on.
2. Maybe set_machine_constraints() happened before we could resolve
supplies (because we failed the first time to resolve) and thus we
might need to propagate an enable that already happened up to our
supply.
Historically regulator_resolve_supply() used _regulator_is_enabled()
to decide whether to turn on the supply.
Let's change things a little bit. Specifically:
1. Let's try to enable the supply and the regulator in the same place,
both in set_machine_constraints(). This means that we have exactly
the same logic for enabling the supply and the regulator.
2. Let's properly set use_count when we enable always-on or boot-on
regulators even for those that don't have supplies. The previous
commit 1fc12b05895e ("regulator: core: Avoid propagating to
supplies when possible") only did this right for regulators with
supplies.
3. Let's make it clear that the only time we need to enable the supply
in regulator_resolve_supply() is if the main regulator is currently
in use. By using use_count (like the rest of the code) to decide
if we're going to enable our supply we keep everything consistent.
Overall the new scheme should be cleaner and easier to reason about.
In addition to fixing regulator_summary to be more correct (because of
the more correct use_count), this change also has the effect of no
longer using _regulator_is_enabled() in this code path.
_regulator_is_enabled() could return an error code for some regulators
at bootup (like RPMh) that can't read their initial state. While one
can argue that the design of those regulators is sub-optimal, the new
logic sidesteps this brokenness. This fix in particular fixes
observed problems on Qualcomm sdm845 boards which use the
above-mentioned RPMh regulator. Those problems were made worse by
commit 1fc12b05895e ("regulator: core: Avoid propagating to supplies
when possible") because now we'd think at bootup that the SD
regulators were already enabled and we'd never try them again.
Fixes: 1fc12b05895e ("regulator: core: Avoid propagating to supplies when possible")
Reported-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-4.21
|
|
|
|
The GPIO descriptors used by the S2MPS11 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The GPIO descriptors used by the TPS65090 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The GPIO descriptors used by the S5M8767 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The GPIO descriptors used by the DA9211 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
