| Age | Commit message (Collapse) | Author |
|---|
|
These fields are never used and not required at all, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This problem was introduced by:
commit daad134d6649 ("regulator: core: Request GPIO before creating
sysfs entries")
The error path was not updated correctly after moving GPIO registration
code and in case regulator_ena_gpio_free failed, device_unregister() was
called even though device_register() was not yet called.
This problem breaks the boot at least on all Tegra 32-bit devices. It
will also crash each device that specifices GPIO that is unavaiable at
regulator_register call. Here's error log I've got when forced GPIO to
be invalid:
[ 1.116612] usb-otg-vbus-reg: Failed to request enable GPIO10: -22
[ 1.122794] Unable to handle kernel NULL pointer dereference at
virtual address 00000044
[ 1.130894] pgd = c0004000
[ 1.133598] [00000044] *pgd=00000000
[ 1.137205] Internal error: Oops: 5 [#1] SMP ARM
and here's backtrace from KDB:
Exception stack(0xef11fbd0 to 0xef11fc18)
fbc0: 00000000 c0738a14 00000000 00000000
fbe0: c0b2a0b0 00000000 00000000 c0738a14 c0b5fdf8 00000001 ef7f6074 ef11fc4c
fc00: ef11fc50 ef11fc20 c02a8344 c02a7f1c 60000013 ffffffff
[<c010cee0>] (__dabt_svc) from [<c02a7f1c>] (kernfs_find_ns+0x18/0xf8)
[<c02a7f1c>] (kernfs_find_ns) from [<c02a8344>] (kernfs_find_and_get_ns+0x40/0x58)
[<c02a8344>] (kernfs_find_and_get_ns) from [<c02ac4a4>] (sysfs_unmerge_group+0x28/0x68)
[<c02ac4a4>] (sysfs_unmerge_group) from [<c044389c>] (dpm_sysfs_remove+0x30/0x5c)
[<c044389c>] (dpm_sysfs_remove) from [<c0436ba8>] (device_del+0x48/0x1f4)
[<c0436ba8>] (device_del) from [<c0436d84>] (device_unregister+0x30/0x6c)
[<c0436d84>] (device_unregister) from [<c0403910>] (regulator_register+0x6d0/0xdac)
[<c0403910>] (regulator_register) from [<c04052d4>] (devm_regulator_register+0x50/0x84)
[<c04052d4>] (devm_regulator_register) from [<c0406298>] (reg_fixed_voltage_probe+0x25c/0x3c0)
[<c0406298>] (reg_fixed_voltage_probe) from [<c043d21c>] (platform_drv_probe+0x60/0xb0)
[<c043d21c>] (platform_drv_probe) from [<c043b078>] (driver_probe_device+0x24c/0x440)
[<c043b078>] (driver_probe_device) from [<c043b5e8>] (__device_attach_driver+0xc0/0x120)
[<c043b5e8>] (__device_attach_driver) from [<c043901c>] (bus_for_each_drv+0x6c/0x98)
[<c043901c>] (bus_for_each_drv) from [<c043ad20>] (__device_attach+0xac/0x138)
[<c043ad20>] (__device_attach) from [<c043b664>] (device_initial_probe+0x1c/0x20)
[<c043b664>] (device_initial_probe) from [<c043a074>] (bus_probe_device+0x94/0x9c)
[<c043a074>] (bus_probe_device) from [<c043a610>] (deferred_probe_work_func+0x80/0xcc)
[<c043a610>] (deferred_probe_work_func) from [<c01381d0>] (process_one_work+0x158/0x454)
[<c01381d0>] (process_one_work) from [<c013854c>] (worker_thread+0x38/0x510)
[<c013854c>] (worker_thread) from [<c013e154>] (kthread+0xe8/0x104)
[<c013e154>] (kthread) from [<c0108638>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@tieto.com>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-core
|
|
regulator_attr_is_visible (which is a .is_visible callback of
regulator_dev_group attribute_grpup) checks rdev->ena_pin to decide if
"status" file should be present in sysfs. This field is set at the end
of regulator_ena_gpio_request so it has to be called before
device_register() otherwise this test will always fail, causing "status"
file to not be visible.
Since regulator_attr_is_visible also tests for is_enabled() op, this
problem is only visible for regulators that does not define this
callback, like regulator-fixed.c.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@tieto.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't print out an error with the driver sees EPROBE_DEFER when
attempting to get the gpio. These errors are usually transient; the
probe will be retried later.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove the s2mps11_info.rdev_num because it is not used outside of
probe.
Suggested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
i2c_master_send() returns the number of bytes written on success.
So current code returns 2 if ad5398_write_reg() success.
This return value is propagated to .set_current_limit, .enable and .disable
callbacks of regulator_ops. This can be a problem, for example, if the
users test if the return value of regulator_set_current_limit() is 0.
Fix it by making ad5398_write_reg() return 0 on success.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
MAXIM Semiconductor's PMIC, MAX77620 and MAX20024 have the
multiple DCDC and LDOs. This supplies the power to different
components of the system.
Also these rails has configuration for ramp time, flexible
power sequence, slew rate etc.
Add regulator driver to access these rails via regulator APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Following BUILD_BUG_ON using a variable fails for some of the compilers
and optimization levels (reported for gcc 4.9):
var = ARRAY_SIZE(s2mps15_regulators);
BUILD_BUG_ON(S2MPS_REGULATOR_MAX < var);
Fix this by using ARRAY_SIZE directly.
Additionally add missing BUILD_BUG_ON check for S2MPS15 device (the
check ensures that internal arrays are big enough to hold data for all
of regulators on all devices).
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The s5m8767_pmic_probe() function calls s5m8767_get_register() to
read data without checking the return code, which produces a compile-time
warning when that data is accessed:
drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
drivers/regulator/s5m8767.c:924:7: error: 'enable_reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/regulator/s5m8767.c:944:30: error: 'enable_val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the s5m8767_get_register() function to return a -EINVAL
not just for an invalid register number but also for an invalid
regulator number, as both would result in returning uninitialized
data. The s5m8767_pmic_probe() function is then changed accordingly
to fail on a read error, as all the other callers of s5m8767_get_register()
already do.
In practice this probably cannot happen, as we don't call
s5m8767_get_register() with invalid arguments, but the gcc
warning seems valid in principle, in terms writing safe
error checking.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9c4c60554acf ("regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap")
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The vexpress regulator implementation is currently just called vexpress.
This is a problem because it clashes with another module with the same
name in hardware monitors.
This patch renames the vexpress regulator implementation to
vexpress-regulator so that there will be no clash in the module namespace.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Originally the helper macros used uppercase regulator names, which
are primarily used to expand to the regulator ID enum, as the default
names. This is aestheticly unpleasent.
Since the of_match bits are the same, just lowercase, use that as the
default names instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the regulator driver for hi655x PMIC.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's perfectly valid to use the LTC3589 without an interrupt pin
connected to it. Currently, the driver probing fails when client->irq
is 0 (which means "no interrupt"). Don't register the interrupt
handler in that case but successfully finish the device probing instead.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The max77686 and max77802 regulator drivers are for sub-devices of a MFD
driver for some PMIC blocks. But the same object file name (max77686.o)
was used for both the common MFD driver and the max77686 regulator one.
This confuses kbuild if both drivers are built as module causing the MFD
driver to not be copied when installing the modules.
Also, max77{686,802} are a quite generic name for MFD subdevices drivers
so it is better to rename them to max77{686,802}-regulator like it's the
case for most regulator drivers.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds support for TPS65912 PMIC regulators.
The regulators set consists of 4 DCDCs and 10 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The old tps65912 driver is being replaced, delete old driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
LP872x regulators are made active via the EN pin, which might be hooked to a
GPIO. This adds support for driving the GPIO high when the driver is in use.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some devices don't hook the DVS pin to a GPIO but to ground or VCC.
In those cases, it is not a problem to have no DVS GPIO provided, as the current
code will already switch to software-only DVS selection:
When the DVS GPIO is invalid, lp872x_init_dvs jumps to the set_default_dvs_mode
label, which instructs the chip not to use the DVS pin at all and do it all in
software instead (by clearing the LP8720_EXT_DVS_M bit in the
LP872X_GENERAL_CFG register).
That is reflected later in the code, when setting the bucks (the DVS pin only
applies to the bucks) by checking for the LP8720_EXT_DVS_M bit on the
LP872X_GENERAL_CFG register (in lp872x_select_buck_vout_addr) to decide whether
to use software or hardware DVS selection.
Thus, there is no need to print a warning when the DVS GPIO is invalid.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds new regulator driver to support ACT8945A MFD
chip's regulators.
The ACT8945A has three step-down DC/DC converters and four
low-dropout regulators.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
AXP20X datasheet lists the possible voltage settings for LDO4, so
it was implemented using a voltage table. Upon closer examination,
the valid voltages can be mapped into 3 linear ranges.
Move AXP20X LDO4 to use linear ranges. The supporting code can be
reused with later AXP8xx PMICs, which have a number of regulators
that have 2 linear ranges.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch-type regulators, such as DC1SW on AXP22X, are a secondary output
from DCDC1. They are just an on/off switch, and the driver should not
try to read its voltage directly from the DCDC1 control registers.
Instead, the core will pass down the voltage from the regulator supply
chain.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Documentation/devicetree/bindings/regulator/mt6397-regulator.txt doc
mentions that a compatible "mediatek,mt6397-regulator" is required for
the MT6397 device node but the driver doesn't provide a OF match table so
the platform bus .match fallbacks to match using the driver name instead.
This also means that module auto-loading is broken for this driver since
the MFD driver that register the device, has a .of_compatible set so the
platform .uevent callback reports a OF modalias that's not in the module.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The platform bus_type .match callback attempts to match the platform device
name with an entry on the .id_table if provided and fallbacks to match with
the driver's name if a table is not provided.
Using a platform device ID to match is more explicit, allows the driver to
support more than one device and also the MODULE_DEVICE_TABLE macro can be
used to export the module aliases information instead of the MODULE_ALIAS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As we now free the constraints in regulator_dev_release we will still
call free on the constraints pointer even if we went down an error
path in regulator_register, because it is only allocated after the
device_register. As such we no longer need to free rdev->constraints
on the error paths, so this patch removes said frees.
Fixes: 29f5f4860a8e ("regulator: core: Move more deallocation into class unregister")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Aside from a fix for a spurious warning (which caused more problems
than it fixed in the fixing really) this is all driver updates,
including new drivers for Dialog PV88060/90 and TI LM363x and TPS65086
devices. The qcom_smd driver has had PM8916 and PMA8084 support
added"
* tag 'regulator-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: core: remove some dead code
regulator: core: use dev_to_rdev
regulator: lp872x: Get rid of duplicate reference to DVS GPIO
regulator: lp872x: Add missing of_match in regulators descriptions
regulator: axp20x: Fix GPIO LDO enable value for AXP22x
regulator: lp8788: constify regulator_ops structures
regulator: wm8*: constify regulator_ops structures
regulator: da9*: constify regulator_ops structures
regulator: mt6311: Use REGCACHE_RBTREE
regulator: tps65917/palmas: Add bypass ops for LDOs with bypass capability
regulator: qcom-smd: Add support for PMA8084
regulator: qcom-smd: Add PM8916 support
soc: qcom: documentation: Update SMD/RPM Docs
regulator: pv88090: logical vs bitwise AND typo
regulator: pv88090: Fix irq leak
regulator: pv88090: new regulator driver
regulator: wm831x-ldo: Use platform_register/unregister_drivers()
regulator: wm831x-dcdc: Use platform_register/unregister_drivers()
regulator: lp8788-ldo: Use platform_register/unregister_drivers()
regulator: core: Fix nested locking of supplies
...
|
|
Commit 70cfef26267474 ("regulator: Add lockdep asserts to help detecting
locking misuse") successfully created this WARN, let's fix it:
[ 1.218660] WARNING: CPU: 0 PID: 553 at drivers/regulator/core.c:3646 regulator_notifier_call_chain+0x5c/0x88()
...
[ 1.220278] [<c0246c20>] (regulator_notifier_call_chain) from [<c02498b4>] (da9210_irq_handler+0x74/0x10c)
[ 1.220412] r7:c0080cac r6:eb1daa00 r5:e64bbf10 r4:00000002
[ 1.220547] [<c0249840>] (da9210_irq_handler) from [<c0080cd8>] (irq_thread_fn+0x2c/0x44)
...
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Setting the set_suspend_enable/disable callback to support
enable and disable the dcdc when system is suspend.
Signed-off-by: zhangqing <zhangqing@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
'regulator/topic/qcom-smd', 'regulator/topic/tps6105x', 'regulator/topic/tps65086' and 'regulator/topic/tps65218' into regulator-next
|
|
'regulator/topic/mt6311', 'regulator/topic/optional', 'regulator/topic/palmas' and 'regulator/topic/pv88060' into regulator-next
|
|
'regulator/topic/lm363x', 'regulator/topic/lockdep' and 'regulator/topic/lp872x' into regulator-next
|
|
|
|
'regulator/fix/mt6311' into regulator-linus
|
|
Originally queue_delayed_work() used to negative error codes or 0 and 1
on success depending if the work was queued or not. It caused a lot of
bugs where people treated all non-zero returns as failures so we changed
it to return bool instead in d4283e937861 ('workqueue: make queueing
functions return bool'). Now it never returns failure.
Checking for negative values causes a static checker warning since it is
impossible based on the bool type.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use dev_to_rdev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The lp872x structure holds a reference to the DVS GPIO, but it is never actually
used anywhere, since a first reference exists from the lp872x_dvs structure.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In order to select the regulators via of_find_regulator_by_node (and thus use
them in devicetree), defining of_match for each regulator is required.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The enable/disable values for GPIO LDOs are reversed. It seems no one
noticed as AXP22x support was introduced recently, and no one was using
the GPIO LDOs, either because no designs actually use them or board
support hasn't caught up.
Fixes: 1b82b4e4f954 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This regulator is on a slow i2c bus. Register accesses are very simple,
they all either enable/disable a regulator channel, or select a new
voltage level. Thus, reading registers from the device will always
return what was last written.
Therefore we can save a lot of time when reading registers by using a
regmap_cache. Since the register map is relatively large, but we only
ever access a few of them, we use an RBTREE cache.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
set/get_bypass ops were missing for ldo1/ldo2 on tps65917 and
ldo9 on palmas/tps659038 which support bypass mode.
Adding the bypass ops helps consumers configure these ldos in
bypass mode or remove bypass mode if need be.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds support and documentation for the PMA8084 regulators
found on APQ8084 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds support and documentation for the PM8916 regulators
found on MSM8916 platforms.
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
These were supposed to be bitwise AND instead of logical. Also kernel
style is for the operator to be on the first line and I removed some
extra parenthesis.
Fixes: c90456e36d9c ('regulator: pv88090: new regulator driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_request_threaded_irq to ensure the irq is freed when unload the
module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is the driver for the Powerventure PV88090 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
