| Age | Commit message (Collapse) | Author |
|---|
|
The remoteproc core creates certain standard debugfs entries,
that does not give a whole lot of useful information for the
PRUs. The PRU remoteproc driver is enhanced to add additional
debugfs entries for PRU. These will be auto-cleaned up when
the parent rproc debug directory is removed.
The enhanced debugfs support adds two new entries: 'regs' and
'single_step'. The 'regs' dumps out the useful CTRL sub-module
registers as well as each of the 32 GPREGs and CT_REGs registers.
The GPREGs and CT_REGs though are printed only when the PRU is
halted and accessible as per the IP design.
The 'single_step' utilizes the single-step execution of the PRU
cores. Writing a non-zero value performs a single step, and a
zero value restores the PRU to execute in the same mode as the
mode before the first single step. (note: if the PRU is halted
because of a halt instruction, then no change occurs).
Logic for setting the PC and jumping over a halt instruction shall
be added in the future.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-5-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The firmware blob can contain optional ELF sections: .resource_table
section and .pru_irq_map one. The second one contains the PRUSS
interrupt mapping description, which needs to be setup before powering
on the PRU core. To avoid RAM wastage this ELF section is not mapped to
any ELF segment (by the firmware linker) and therefore is not loaded to
PRU memory.
The PRU interrupt configuration is handled within the PRUSS INTC irqchip
driver and leverages the system events to interrupt channels and host
interrupts mapping configuration. Relevant irq routing information is
passed through a special .pru_irq_map ELF section (for interrupts routed
to and used by PRU cores) or via the PRU application's device tree node
(for interrupts routed to and used by the main CPU). The mappings are
currently programmed during the booting/shutdown of the PRU.
The interrupt configuration passed through .pru_irq_map ELF section is
optional. It varies on specific firmware functionality and therefore
have to be unwinded during PRU stop and performed again during
PRU start.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Co-developed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-4-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The Programmable Real-Time Unit Subsystem (PRUSS) consists of
dual 32-bit RISC cores (Programmable Real-Time Units, or PRUs)
for program execution. This patch adds a remoteproc platform
driver for managing the individual PRU RISC cores life cycle.
The PRUs do not have a unified address space (have an Instruction
RAM and a primary Data RAM at both 0x0). The PRU remoteproc driver
therefore uses a custom remoteproc core ELF loader ops. The added
.da_to_va ops is only used to provide translations for the PRU
Data RAMs. This remoteproc driver does not have support for error
recovery and system suspend/resume features. Different compatibles
are used to allow providing scalability for instance-specific device
data if needed. The driver uses a default firmware-name retrieved
from device-tree for each PRU core, and the firmwares are expected
to be present in the standard Linux firmware search paths. They can
also be adjusted by userspace if required through the sysfs interface
provided by the remoteproc core.
The PRU remoteproc driver uses a client-driven boot methodology: it
does _not_ support auto-boot so that the PRU load and boot is dictated
by the corresponding client drivers for achieving various usecases.
This allows flexibility for the client drivers or applications to set
a firmware name (if needed) based on their desired functionality and
boot the PRU. The sysfs bind and unbind attributes have also been
suppressed so that the PRU devices cannot be unbound and thereby
shutdown a PRU from underneath a PRU client driver.
The driver currently supports the AM335x, AM437x, AM57xx and 66AK2G
SoCs, and support for other TI SoCs will be added in subsequent
patches.
Co-developed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-3-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
There is a spelling mistake in the Kconfig help text. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201204193411.1152006-1-colin.king@canonical.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The latest version of sysmon_stop() starts by initializing
the sysmon->shutdown_acked variable, but then overwrites it
with an uninitialized variable later:
drivers/remoteproc/qcom_sysmon.c:551:11: error: variable 'acked' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
else if (sysmon->ept)
^~~~~~~~~~~
drivers/remoteproc/qcom_sysmon.c:554:27: note: uninitialized use occurs here
sysmon->shutdown_acked = acked;
^~~~~
Remove the local 'acked' variable again and set the state directly.
Fixes: 5c212aaf5457 ("remoteproc: sysmon: Expose the shutdown result")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201204193740.3162065-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The J7200 SoCs have a revised R5FSS IP that adds a unique feature w.r.t
TCM sizing. Each R5F core in a cluster typically has 32 KB each of ATCM
and BTCM, with only the Core0 TCMs usable in LockStep mode. This revised
IP however doubles the total available TCM in LockStep mode by making the
Core1 TCM visible immediately after the corresponding Core0 TCM.
The R5F DT nodes on the J7200 SoCs define double (64 KB) the normal TCM
size (32 KB) for R5F Core0 for each of ATCM and BTCM to represent the
above. This increased TCM memory is only usable in LockStep-mode, and
has to be adjusted to the normal 32 KB size in Split mode. Enhance the
TI K3 R5F remoteproc for this logic through a new function. The adjustment
is a no-op on prior SoCs and relies on the correct DTS node sizes in
LockStep-mode on applicable SoCs.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201119010531.21083-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The K3 J7200 SoC family has a revised R5F sub-system and contains a
subset of the R5F clusters present on J721E SoCs. The K3 J7200 SoCs
only have two dual-core Arm R5F clusters/subsystems with 2 R5F cores
each. One cluster is present within the MCU voltage domain (MCU_R5FSS0),
while the other is present in the MAIN voltage domain (MAIN_R5FSS0).
The revised IP has the following two new features:
1. TCMs are auto-initialized during module power-up, and the behavior
is programmable through a MMR bit.
2. The LockStep-mode allows the Core1 TCMs to be combined with the
Core0 TCMs effectively doubling the amount of TCMs available.
The LockStep-mode on previous SoCs could only use the Core0 TCMs.
This combined TCMs appear contiguous at the respective Core0 TCM
addresses.
Extend the support to these clusters in the K3 R5F remoteproc driver
using J7200 specific compatibles. Logic for the second feature is
added in the next patch. The integration of these clusters is very
much similar to J721E SoCs otherwise.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201119010531.21083-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
A new API, rproc_set_firmware() is added to allow the remoteproc platform
drivers and remoteproc client drivers to be able to configure a custom
firmware name that is different from the default name used during
remoteproc registration. This function is being introduced to provide
a kernel-level equivalent of the current sysfs interface to remoteproc
client drivers, and can only change firmwares when the remoteproc is
offline. This allows some remoteproc drivers to choose different firmwares
at runtime based on the functionality the remote processor is providing.
The TI PRU Ethernet driver will be an example of such usage as it
requires to use different firmwares for different supported protocols.
Also, update the firmware_store() function used by the sysfs interface
to reuse this function to avoid code duplication.
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201121032042.6195-1-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Improve the style of a few of the error messages printed by the sysmon
implementation and fix the copy-pasted shutdown error in the send-event
function.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Requesting a graceful shutdown through the shared memory state signals
will not be acked in the event that sysmon has already successfully shut
down the remote firmware. So extend the stop request API to optionally
take the remoteproc's sysmon instance and query if there's already been
a successful shutdown attempt, before doing the signal dance.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
A graceful shutdown of the Qualcomm remote processors where
traditionally performed by invoking a shared memory state signal and
waiting for the associated ack.
This was later superseded by the "sysmon" mechanism, where some form of
shared memory bus is used to send a "graceful shutdown request" message
and one of more signals comes back to indicate its success.
But when this newer mechanism is in effect the firmware is shut down by
the time the older mechanism, implemented in the remoteproc drivers,
attempts to perform a graceful shutdown - and as such it will never
receive an ack back.
This patch therefor track the success of the latest shutdown attempt in
sysmon and exposes a new function in the API that the remoteproc driver
can use to query the success and the necessity of invoking the older
mechanism.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The reliance on the remoteproc's state for determining when to send
sysmon notifications to a remote processor is racy with regard to
concurrent remoteproc operations.
Further more the advertisement of the state of other remote processor to
a newly started remote processor might not only send the wrong state,
but might result in a stream of state changes that are out of order.
Address this by introducing state tracking within the sysmon instances
themselves and extend the locking to ensure that the notifications are
consistent with this state.
Fixes: 1f36ab3f6e3b ("remoteproc: sysmon: Inform current rproc about all active rprocs")
Fixes: 1877f54f75ad ("remoteproc: sysmon: Add notifications for events")
Fixes: 1fb82ee806d1 ("remoteproc: qcom: Introduce sysmon")
Cc: stable@vger.kernel.org
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The application processor accessing the MBA region after assigning it to
the remote Q6 would lead to an XPU violation. Fix this by un-mapping the
MBA region post firmware copy and MBA text log dumps.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1604473422-29639-2-git-send-email-sibis@codeaurora.org
[bjorn: Renamed "ptr" to "mba_region"]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Fix the sparse warnings reported by the kernel test bot by replacing
ioremap calls with memremap.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1604473422-29639-1-git-send-email-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The only usage of qmi_indication_handler[] is to pass its address to
qmi_handle_init() which accepts a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201122234540.34623-1-rikard.falkeborn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The main purpose of the loop is to load the memory to the SCP SRAM.
If filesz is 0, can go to next program header directly.
We don't need to try to validate the FW binary for those filesz==0
segments.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116084413.3312631-3-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
It is valid if offset+length == sram_size.
For example, sram_size=100, offset=99, length=1. Accessing offset 99
with length 1 is valid.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116084413.3312631-2-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Fixes the following sparse errors on dma_alloc_coherent() and
dma_free_coherent().
On drivers/remoteproc/mtk_scp.c:559:23:
warning: incorrect type in assignment (different address spaces)
expected void [noderef] __iomem *cpu_addr
got void *
On drivers/remoteproc/mtk_scp.c:572:56:
warning: incorrect type in argument 3 (different address spaces)
expected void *cpu_addr
got void [noderef] __iomem *cpu_addr
The cpu_addr is not a __iomem address. Removes the marker.
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116082537.3287009-3-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Fixes the following sparse errors on sram power on and off:
On drivers/remoteproc/mtk_scp.c:306:17:
warning: incorrect type in argument 2 (different address spaces)
expected void volatile [noderef] __iomem *addr
got void *addr
On drivers/remoteproc/mtk_scp.c:307:9:
warning: incorrect type in argument 2 (different address spaces)
expected void volatile [noderef] __iomem *addr
got void *addr
On drivers/remoteproc/mtk_scp.c:314:9:
warning: incorrect type in argument 2 (different address spaces)
expected void volatile [noderef] __iomem *addr
got void *addr
On drivers/remoteproc/mtk_scp.c:316:17:
warning: incorrect type in argument 2 (different address spaces)
expected void volatile [noderef] __iomem *addr
got void *addr
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116082537.3287009-2-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The only usage of st_rproc_ops is to pass its address to rproc_alloc()
which accepts a const pointer. Make it const to allow the compiler to
put it in read-only memory.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201107233630.9728-3-rikard.falkeborn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The only usage of ingenic_rproc_ops is to pass its address to
devm_rproc_alloc(), which accepts a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201107233630.9728-2-rikard.falkeborn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
In order to move wkup_m3 to probe without platform data, let's add
support for using optional reset control driver if configured in the
dts. With this change and the related dts change, we can start
dropping the platform data for am335x.
And once wkup_m3 no longer needs platform data, we can simply drop the
related legacy reset platform data callbacks from wkup_m3 driver later
on after also am437x no longer depends on it.
Cc: linux-remoteproc@vger.kernel.org
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The function cast causes a warning with "make W=1"
drivers/remoteproc/ti_k3_r5_remoteproc.c: In function 'k3_r5_probe':
drivers/remoteproc/ti_k3_r5_remoteproc.c:1368:12: warning: cast between incompatible function types from 'int (*)(struct platform_device *)' to 'void (*)(void *)' [-Wcast-function-type]
Rewrite the code to avoid the cast, and fix the incorrect return
type of the callback.
Fixes: 6dedbd1d5443 ("remoteproc: k3-r5: Add a remoteproc driver for R5F subsystem")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026160533.3705998-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
So far we have been doing all proxy votes by voting for raw voltages/load
through the regulator interface. But actually VDDCX and VDDMX represent
power domains that should be preferably managed using corner votes
through the power domain interface.
Looking closer the code was actually never doing the proxy votes
correctly: The vddcx regulator is specified as:
{ "vddcx", .super_turbo = true },
which is supposed to say that we should vote for the maximum corner
of the VDDCX power domain. But actually "super_turbo" is unused so
all we did so far is to enable the power domain. We did not vote for
it to scale to the maximum performance state.
Using them through the power domain interface allows voting for the
maximum performance state. However, we still need to support using
them through the regulator interface for old device trees.
The way this is implemented here is that we check if attaching the
two power domain succeeds. If yes, we skip the first "num_pd_vregs"
regulators in the "vregs" list and only request the remaining ones.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-9-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Newer platforms vote for necessary power domains through the power
domain subsystem. For historical reasons older platforms like MSM8916
or MSM8974 still control these as regulators.
Managing them as power domains is preferred since that allows us
to vote for corners instead of raw voltages.
Make it possible for MSM8916 and MSM8974 to manage these as power
domains. For compatibility with old device trees we still need to
support falling back to the regulators when necessary.
The way this is implemented here is that the deprecated regulators
are defined as "fallback_proxy_supply". Only if attaching the power
domains fails because they are not specified (-ENODATA) we request
and manage the fallback regulators instead.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-7-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This introduces support for the Mediatek MT9182 SCP and controlling
the Cortex R5F processors found in TI K3 platforms. It clones the
longstanding debugfs interface for controlling crash handling to
sysfs. Lastly it solves a bug where after a warm reset of Qualcomm
platforms the modem would crash upon first boot"
* tag 'rproc-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc/mediatek: Remove non-standard dsb()
remoteproc: Add recovery configuration to the sysfs interface
remoteproc: Add coredump as part of sysfs interface
remoteproc: Change default dump configuration to "disabled"
remoteproc: k3-r5: Add loading support for on-chip SRAM regions
remoteproc: k3-r5: Initialize TCM memories for ECC
remoteproc: k3-r5: Add a remoteproc driver for R5F subsystem
dt-bindings: remoteproc: Add bindings for R5F subsystem on TI K3 SoCs
remoteproc/mediatek: Add support for mt8192 SCP
remoteproc: Fixup coredump debugfs disable request
remoteproc: qcom_q6v5: Assign mpss region to Q6 before MBA boot
remoteproc/mediatek: fix null pointer dereference on null scp pointer
remoteproc: stm32: Fix pointer assignement
remoteproc: scp: add COMPILE_TEST dependency
|
|
As reported by Stephen, dsb() is not declared on e.g. x86_64, preventing
the mtp_scp from building. Simply remove the barrier (and the readback),
suggested by Pi-Hsun to resolve this.
Fixes: fd0b6c1ff85a ("remoteproc/mediatek: Add support for mt8192 SCP")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Pi-Hsun Shih <pihsun@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
|
|
Add recovery configuration to the sysfs interface. This will
allow usage of this configuration feature in production
devices where access to debugfs might be limited.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1601662144-5964-4-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add coredump as part of the sysfs interface. This will
allow usage of this configuration feature in production
devices where access to debugfs might be limited.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1601662144-5964-3-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Currently "default" configuration option means coredumps are
enabled. To avoid confusion rename the "default" configuration
option to "enabled" and disable collection of dumps by default
as doing so makes sense for production devices.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1601662144-5964-2-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The K3 SoCs has various internal on-chip SRAM memories like the SRAM
within the MCU domain or the shared MSMC RAM within NavSS that can be
used for multiple purposes. One such purpose is to have the R5F cores
use a portion of such on-chip SRAM for fast-access data or to directly
execute code.
Add support to the K3 R5 remoteproc driver to parse and support
loading into such memories. The SRAM regions need to be mapped as
normal non-cacheable memory to avoid kernel crashes when the remoteproc
loader code uses the Arm64 memset library function (the "DC ZVA"
instruction throws a alignment fault on device type memory).
These SRAM regions are completely optional as not all firmware images
require these memories, and any such memory has to be reserved as such
in the DTS files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201002234234.20704-5-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The R5F processors on K3 SoCs all have two TCMs (ATCM and BTCM) that
support 32-bit ECC. The TCMs are typically loaded with some boot-up
code to initialize the R5 MPUs to further execute code out of DDR.
The ECC for the TCMs is enabled by default on K3 SoCs due to internal
default tie-off values, but the TCM memories are not initialized on
device power up. Any read access without the corresponding TCM memory
location initialized will generate an ECC error, and any such access
from a A72 or A53 core will trigger a SError.
So, zero initialize both the TCM memories before loading any firmware
onto a R5F in remoteproc mode. Any R5F booted from U-Boot/SPL would
require a similar initialization in the bootloader. Note that both
the TCMs are initialized unconditionally as the TCM enable config bits
only manage the access and visibility from R5.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201002234234.20704-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The TI K3 family of SoCs typically have one or more dual-core Arm Cortex
R5F processor clusters/subsystems (R5FSS). This R5F subsystem/cluster
can be configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. This subsystem
has 64 KB each Tightly-Coupled Memory (TCM) internal memories for each
core split between two banks - TCMA and TCMB (further interleaved into
two banks). The subsystem does not have an MMU, but has a Region Address
Translater (RAT) module that is accessible only from the R5Fs for providing
translations between 32-bit CPU addresses into larger system bus addresses.
Add a remoteproc driver to support this subsystem to be able to load and
boot the R5F cores primarily in LockStep mode. The code also includes the
base support for Split mode. Error Recovery and Power Management features
are not currently supported. Loading support includes the internal TCMs
and DDR. RAT support is left for a future patch, and as such the reserved
memory carveout regions are all expected to be using memory regions within
the first 2 GB.
The R5F remote processors do not have an MMU, and so require fixed memory
carveout regions matching the firmware image addresses. Support for this
is provided by mandating multiple memory regions to be attached to the
remoteproc device. The first memory region will be used to serve as the
DMA pool for all dynamic allocations like the vrings and vring buffers.
The remaining memory regions are mapped into the kernel at device probe
time, and are used to provide address translations for firmware image
segments without the need for any RSC_CARVEOUT entries. Any firmware
image using memory outside of the supplied reserved memory carveout
regions will be errored out.
The R5F processors on TI K3 SoCs require a specific sequence for booting
and shutting down the processors. This sequence is also dependent on the
mode (LockStep or Split) the R5F cluster is configured for. The R5F cores
have a Memory Protection Unit (MPU) that has a default configuration that
does not allow the cores to run out of DDR out of reset. This is resolved
by using the TCMs for boot-strapping code that applies the appropriate
executable permissions on desired DDR memory. The loading into the TCMs
requires that the resets be released first with the cores in halted state.
The Power Sleep Controller (PSC) module on K3 SoCs requires that the cores
be in WFI/WFE states with no active bus transactions before the cores can
be put back into reset. Support for this is provided by using the newly
introduced .prepare() and .unprepare() ops in the remoteproc core. The
.prepare() ops is invoked before any loading, and the .unprepare() ops
is invoked after the remoteproc resource cleanup. The R5F core resets
are deasserted in .prepare() and asserted in .unprepare(), and the cores
themselves are started and halted in .start() and .stop() ops. This
ensures symmetric usage and allows the R5F cores state machine to be
maintained properly between using the sysfs 'state' variable, bind/unbind
and regular module load/unload flows.
The subsystem is represented as a single remoteproc in LockStep mode, and
as two remoteprocs in Split mode. The driver uses various TI-SCI interfaces
to talk to the System Controller (DMSC) for managing configuration, power
and reset management of these cores. IPC between the A53 cores and the R5
cores is supported through the virtio rpmsg stack using shared memory and
OMAP Mailboxes.
The AM65x SoCs typically have a single R5FSS in the MCU voltage domain. The
J721E SoCs uses a slightly revised IP and typically have three R5FSSs, with
one cluster present within the MCU voltage domain (MCU_R5FSS0), and the
remaining two clusters present in the MAIN voltage domain (MAIN_R5FSS0 and
MAIN_R5FSS1). The integration of these clusters on J721E SoC is also
slightly different in that these IPs do support an actual local reset line,
while they are a no-op on AM65x SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201002234234.20704-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Split out all the bits that are purely for dma_map_ops implementations
and related code into a new <linux/dma-map-ops.h> header so that they
don't get pulled into all the drivers. That also means the architecture
specific <asm/dma-mapping.h> is not pulled in by <linux/dma-mapping.h>
any more, which leads to a missing includes that were pulled in by the
x86 or arm versions in a few not overly portable drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This will improve this driver's build coverage.
Reported-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support for mt8192 SCP.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200921094847.2112399-1-pihsun@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Fix the discrepancy observed between accepted input and read back value
while disabling remoteproc coredump through the coredump debugfs entry.
Fixes: 3afdc59e4390 ("remoteproc: Add coredump debugfs entry")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200916145100.15872-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
On secure devices which support warm reset, the MBA firmware requires
access to the modem region to clear them out. Hence provide Q6 access
to this region before MBA boot. This will be a nop during a modem SSR.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200917175840.18708-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Currently when pointer scp is null a dev_err is being called that
references the pointer which is the very thing we are trying to
avoid doing. Remove the extraneous error message to avoid this
issue.
Addresses-Coverity: ("Dereference after null check")
Fixes: 63c13d61eafe ("remoteproc/mediatek: add SCP support for mt8183")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200918152428.27258-1-colin.king@canonical.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The new field 'dma_range_map' in struct device is used to facilitate the
use of single or multiple offsets between mapping regions of cpu addrs and
dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only
capable of holding a single uniform offset and had no region bounds
checking.
The function of_dma_get_range() has been modified so that it takes a single
argument -- the device node -- and returns a map, NULL, or an error code.
The map is an array that holds the information regarding the DMA regions.
Each range entry contains the address offset, the cpu_start address, the
dma_start address, and the size of the region.
of_dma_configure() is the typical manner to set range offsets but there are
a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel
driver code. These cases now invoke the function
dma_direct_set_offset(dev, cpu_addr, dma_addr, size).
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[hch: various interface cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
|
|
Fix the assignment of the @state pointer - it is obviously wrong.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Fixes: 376ffdc04456 ("remoteproc: stm32: Properly set co-processor state when attaching")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200831213758.206690-1-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This will improve this driver's build coverage.
Reported-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Link: https://lore.kernel.org/r/20200915012911.489820-1-acourbot@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This introduces a new "detached" state for remote processors that are
deemed to be running at the time Linux boots and the infrastructure
for "attaching" to these. It then introduces the support for
performing this operation for the STM32 platform.
The coredump functionality is moved out from the core file and gains
support for an optional mode where the recovery phase awaits the
notification from devcoredump that the dump should be released. This
allows userspace to grab the coredump in scenarios where vmalloc space
is too low for creating a complete copy of the coredump before handing
this to devcoredump.
A new character device based interface is introduced to allow tying
the stoppage of a remote processor to the termination of a user space
process. This is useful in situations when such process provides
crucial resources/operations for the firmware running on the remote
processor.
The Texas Instrument K3 driver gains support for the C66x and C71x
DSPs.
Qualcomm remoteprocs gains support for stashing relocation information
in IMEM, to aid post mortem debugging and the crash notification
mechanism is generalized to be reusable in cases where loosely coupled
drivers needs to know about the status of a remote processor. One such
example is the IPA hardware block, which is jointly owned with the
modem and migrated to this improved interface.
It also introduces a number of bug fixes and debug improvements for
the Qualcomm modem remoteproc driver.
And it cleans up the inconsistent interface for remoteproc drivers to
implement power management"
* tag 'rproc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (56 commits)
remoteproc: core: Register the character device interface
remoteproc: Add remoteproc character device interface
remoteproc: kill IPA notify code
net: ipa: new notification infrastructure
remoteproc: k3-dsp: Add support for C71x DSPs
dt-bindings: remoteproc: k3-dsp: Update bindings for C71x DSPs
remoteproc: k3-dsp: Add support for L2RAM loading on C66x DSPs
remoteproc: k3-dsp: Add a remoteproc driver of K3 C66x DSPs
dt-bindings: remoteproc: Add bindings for C66x DSPs on TI K3 SoCs
remoteproc: k3: Add TI-SCI processor control helper functions
remoteproc: Introduce rproc_of_parse_firmware() helper
dt-bindings: arm: keystone: Add common TI SCI bindings
remoteproc: qcom_q6v5_mss: Remove redundant running state
remoteproc: qcom: q6v5: Update running state before requesting stop
remoteproc: qcom_q6v5_mss: Add modem debug policy support
remoteproc: qcom_q6v5_mss: Validate modem blob firmware size before load
remoteproc: qcom_q6v5_mss: Validate MBA firmware size before load
rpmsg: update documentation
remoteproc: qcom_q6v5_mss: Add MBA log extraction support
remoteproc: Add coredump debugfs entry
...
|
|
Add the character device during rproc_add. This would create
a character device node at /dev/remoteproc<index>. Userspace
applications can interact with the remote processor using this
interface.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1596044401-22083-3-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add the character device interface into remoteproc framework.
This interface can be used in order to boot/shutdown remote
subsystems and provides a basic ioctl based interface to implement
supplementary functionality. An ioctl call is implemented to enable
the shutdown on release feature which will allow remote processors to
be shutdown when the controlling userspace application crashes or hangs.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1596044401-22083-2-git-send-email-sidgup@codeaurora.org
[bjorn: s/int32_t/s32/ per checkpatch]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The IPA code now uses the generic remoteproc SSR notification
mechanism. This makes the original IPA notification code unused
and unnecessary, so get rid of it.
This is effectively a revert of commit d7f5f3c89c1a ("remoteproc:
add IPA notification to q6v5 driver").
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200724181142.13581-3-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The Texas Instrument's K3 J721E SoCs have a newer next-generation
C71x DSP Subsystem in the MAIN voltage domain in addition to the
previous generation C66x DSP subsystems. The C71x DSP subsystem is
based on the TMS320C71x DSP CorePac module. The C71x CPU is a true
64-bit machine including 64-bit memory addressing and single-cycle
64-bit base arithmetic operations and supports vector signal processing
providing a significant lift in DSP processing power over C66x DSPs.
J721E SoCs use a C711 (a one-core 512-bit vector width CPU core) DSP
that is cache coherent with the A72 Arm cores.
Each subsystem has one or more Fixed/Floating-Point DSP CPUs, with 32 KB
of L1P Cache, 48 KB of L1D SRAM that can be configured and partitioned as
either RAM and/or Cache, and 512 KB of L2 SRAM configurable as either RAM
and/or Cache. The CorePac also includes a Matrix Multiplication Accelerator
(MMA), a Stream Engine (SE) and a C71x Memory Management Unit (CMMU), an
Interrupt Controller (INTC) and a Powerdown Management Unit (PMU) modules.
Update the existing K3 DSP remoteproc driver to add support for this C71x
DSP subsystem. The firmware loading support is provided by using the newly
added 64-bit ELF loader support, and is limited to images using only
external DDR memory at the moment. The L1D and L2 SRAMs are used as scratch
memory when using as RAMs, and cannot be used for loadable segments. The
CMMU is also not supported to begin with, and the driver is designed to
treat the MMU as if it is in bypass mode.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200612225357.8251-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The resets for the DSP processors on K3 SoCs are managed through the
Power and Sleep Controller (PSC) module. Each DSP typically has two
resets - a global module reset for powering on the device, and a local
reset that affects only the CPU while allowing access to the other
sub-modules within the DSP processor sub-systems.
The C66x DSPs have two levels of internal RAMs that can be used to
boot from, and the firmware loading into these RAMs require the
local reset to be asserted with the device powered on/enabled using
the module reset. Enhance the K3 DSP remoteproc driver to add support
for loading into the internal RAMs. The local reset is deasserted on
SoC power-on-reset, so logic has to be added in probe in remoteproc
mode to balance the remoteproc state-machine.
Note that the local resets are a no-op on C71x cores, and the hardware
does not supporting loading into its internal RAMs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-7-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
