| Age | Commit message (Collapse) | Author |
|---|
|
created on two SATA drive
Whenever an I/O for a RAID volume fails with IOCStatus
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED and SCSIStatus equal to
(MPI2_SCSI_STATE_TERMINATED | MPI2_SCSI_STATE_NO_SCSI_STATUS) then
return the I/O to SCSI midlayer with "DID_RESET" (i.e. retry the IO
infinite times) set in the host byte.
Previously, the driver was completing the I/O with "DID_SOFT_ERROR"
which causes the I/O to be quickly retried. However, firmware needed
more time and hence I/Os were failing.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For Dev Handles whose value is less than HBA's phys count number, driver
would return HBA's SAS address value. As a result, for a Virtual SES
device the driver was returning the HBA's SAS address. Updated the
driver to return Virtual SES' SAS address.
[mkp: clarified commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
To reduce the memory footprint of the driver in the kdump kernel, we
apply the following settings when reset_devices is set:
1. Use single MSI-x vector.
2. Disable RDPQ mode.
3. Set sg_table_size to 32 by default.
4) Set SCSI IO Queue depth to 200.
[mkp: fixed commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While removing Expander devices, we are removing expander device entry
from the list before freeing its child devices. While freeing child
device we are finding its parent device node as NULL and therefore we
are not freeing the child device's allocated data structures. Updated
the driver to remove the expander device from the list only after
freeing all its child devices.
[mkp: clarified commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Earlier Active Cable Exception event with reason code "Cable Degraded
(0x02))" was added only for Active Cable. Now this event is extended to
Passive cable too. Re-arranged display message accordingly.
Also added Cable Exception Event event for SAS3008 & SAS3108 HBAs
(i.e. MPI 2.5 spec supporting HBAs). Previously, this event was enabled
only for MPI 2.6 spec supporting HBA devices.
[mkp: typos]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since we have converted all the user of UFS_BIT() macro with the actual
bit position, let remove unused UFS_BIT()macro.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
HOST_ERROR_INDICATOR and DEVICE_ERROR_INDICATOR are not used
anywhere. Also as per JESD223C specification, bit[7:4] are reserved.
Lets remove these #defines.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use actual bit position instead of UFS_BIT() macro. This patch also
changes bit-17 to meaningful #define.
This change is as per discussion here [1]
[1] -> https://lkml.org/lkml/2017/8/28/786
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently UFS HCI uses UFS_BIT() macro to get various bit position for
the hardware registers status bits. Which makes code longer instead of
shorter. This macro does not improve code readability as well. Lets
re-write these macro definition with the actual bit position.
Suggested-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The SCSI host byte should be shifted left by 16 in order to have
scsi_decide_disposition() do the right thing (.i.e. requeue the
command).
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 661134ad3765 ("[SCSI] libiscsi, bnx2i: make bound ep check common")
Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Cc: Chris Leech <cleech@redhat.com>
Acked-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
- a couple of serious fixes: use after free and blacklist for WRITE
SAME
- one error leg fix: write_pending failure
- one user experience problem: do not override max_sectors_kb
- one minor unused function removal
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvscsis: Fix write_pending failure path
scsi: libiscsi: Remove iscsi_destroy_session
scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
scsi: sd: Do not override max_sectors_kb sysfs setting
scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP
|
|
In places like fc_rport_recv_plogi_req and fcoe_ctlr_vn_add we always
take the lport disc_mutex lock before the rports mutex
(rp_mutex) lock. Gaurding list_del_rcu(&rdata->peers) with
disc.disc_mutex in fc_rport_work is correct but the rp_mutex lock
can and should to be dropped before taking that lock else results
in a deadlock.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Calling rmmod() on a FC driver will results in warnings like
WARNING: CPU: 60 PID: 14640 at fs/sysfs/group.c:237 device_del+0x54/0x240()
sysfs group ffffffff81eff140 not found for kobject '3:0:0:3'
The problem here is that during scsi_remove_target() we will iterate
over all devices, but fail to remove any of those as the call to
scsi_device_get() fails the check to module_is_live(). Hence the
devices will not be removed at this point, but all intermediate
structures like fc rport etc. will be. Later on during
scsi_forget_host() the devices are removed for real, but the device
parent is already removed and causes this warning.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Kyle Fortin <kyle.fortin@oracle.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove uses of init_timer_on_stack() with open-coded function and data
assignments that could be expressed using timer_setup_on_stack(). Several
were removed from the stack entirely since there was a one-to-one mapping
of parent structure to timer, those are switched to using timer_setup()
instead. All related callbacks were adjusted to use from_timer().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Petr Mladek <pmladek@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux1394-devel@lists.sourceforge.net
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-s390@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Reed <mdr@sgi.com>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pm@vger.kernel.org
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mark Gross <mark.gross@intel.com>
Cc: linux-watchdog@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: netdev@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lkml.kernel.org/r/1507159627-127660-4-git-send-email-keescook@chromium.org
|
|
For write_pending if the queue is down or client failed then return -EIO
so that LIO can properly process the completed command. Prior we
returned 0 since LIO could not handle it properly. Now with commit
fa7e25cf13a6 ("target: Fix unknown fabric callback queue-full errors")
that patch addresses LIO's ability to handle things right.
Signed-off-by: Bryant G. Ly <bgly@us.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change version to 11.4.0.4
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The internal cfg flag is actually smaller, by 1 (for a partial page
sge), than the sg list maintained by the driver. Thus the check on sg
segments errored out when it shouldn't have
Ensure the check is +1
Note: having a value that is less than what it really is is bogus.
Correcting it now would be a significant rework. Add this item to the
list to be refactored in the merge with efct.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When running NVME io as a NVME host, if the driver is unloaded there
would be oops in lpfc_sli4_issue_wqe.
When unloading, controllers are torn down and the transport initiates
set_property commands to reset the controller and issues aborts to
terminate existing io. The drivers nvme abort and fcp io submit
routines needed to recognize the driver is unloading and fail the new
requests. It didn't, resulting in the oops.
Revise the ls and fcp io submit routines to detect the unloading state
and properly handle their cleanup.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Support RDP and Multiple Frames
If the remote Nport is not logged in, the driver would not populate all
the descriptors in the RDP response payload. Doing so would create a
payload length that requires multiple frames due to exceeding the
default rx buffer size without an explicit login. Currently FC-LS
explicitly states the RDP response must be a single frame sequence.
Thus we did not violate the standard.
Recently, a modification to FC-LS was accepted which allows multi-frame
sequences and all vendors have indicated they are interoperable with the
change. As such, extend RDP support with the additional fields and send
a multi-frame sequence.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Before releasing nvme io back to the io stack for possible retry on
other paths, ensure the io termination is interlocked with the target
device by ensuring the entire ABTS-LS protocol is complete.
Additionally, FC-NVME ABTS-LS protocol does not use RRQ. Remove RRQ
behavior from ABTS-LS.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Firmware update fails with: status x17 add_status x56 on the final write
If multiple DMA buffers are used for the download, some firmware revs
have difficulty with signatures and crcs split across the dma buffer
boundaries. Resolve by making all writes be a single 4k page in length.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver is seeing a NULL pointer in lpfc_nvme_fcp_io_submit. This
was ultimately due to a transport AER being sent on a terminated
controller, thus some of the values were not set. In case we're in a
system without a corrected transport and in case a race condition occurs
where we enter the routine as the teardown is happening in a separate
thread, validate the parameters before starting the io.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The initial implementation of NVME didn't merge with NPIV support. As
such, there are several issues if NPIV is used with NVME. For now,
ensure that if NVME is enabled then NPIV is not enabled.
Support for NPIV with NVME will be added in the near future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
if nvmet targetport registration fails, the driver encounters a NULL
pointer oops in lpfc_hb_timeout_handler.
To fix: if registration fails, ensure nvmet_support is cleared on the
port structure.
Also enhanced the log message on failure.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The descriptions for lpfc_xri_split and lpfc_enable_fc4_type were
poor. Revise for better understanding:
lpfc_xri_split - Percentage of FCP XRI resources versus NVME
lpfc_enable_fc4_type - Enable FC4 Protocol support - FCP / NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Always set ctxp->state to LPFC_NVMET_STE_ABORT if ABORT op gets called
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There are several log messages that report abnormal terminations that by
default are marked warn. These are typically the result of failures due
to invalid controller state or abort completions. They are all natural
when a controller resets.
Unfortunately, as they are logged by default, it makes the admin very
concerned.
Convert the messages to Info.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver is encountering oops in lpfc_sli_calc_ring.
The driver is setting hba_wqidx for FCP based on the policy in use for
NVME. The two may not be the same. Change to set the wqidx based on the
FCP policy.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Under heavy target nvme load duration, the lpfc irq handler is
encountering cpu lockup warnings.
Convert the driver to a shortened ISR handler which identifies the
interrupting condition then schedules a workq thread to process the
completion queue the interrupt was for. This moves all the real work
into the workq element.
As nvmet_fc upcalls are no longer in ISR context, don't set the feature
flags
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Need to make ktime samples more accurate
If ktime is turned on in the middle of an IO, the max calculation could
be misleading. Base sampling on the start time of the IO as opposed to
ktime_on.
Make ISR ktime timestamps be from when CQE is read instead of EQE.
Added additional sanity checks when deciding whether to accept an IO
sample or not.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Local Reject/Invalid RPI errors seen during discovery.
Temporary RPI cleanup was occurring regardless of SLI rev. It's only
necessary on SLI-4.
Adjust the test for whether cleanup is necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Warning messages when NVME_TARGET_FC not defined on ppc builds
The lpfc_nvmet_replenish_context() function is only meaningful when NVME
target mode enabled. Surround the function body with ifdefs for target
mode enablement.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In a link bounce scenario, a condition can occur where the discovery
engine swaps an ndlp structure (address change for an nport). While the
swap was successfully executed by the discovery engine, the driver did
not properly detect a change in the ndlp bound to the nvme rport. This
error resulted in the nvme host transport issuing an IO to the correct
nvme rport, but the lpfc driver addressed a ndlp with an NLP_UNUSED
status and failed the io. This resulting it it looking like there were
missing namespaces and applications failed due to io errors.
To fix, in lpfc_nvme_register_rport, rework the "rebind" case to break
the nvme rport<->ndlp association when the ndlp already has an
nrport. Then rebind the rport to the correct ndlp data and backpointers.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During pci hot plug, the kernel crashes in a list_add_call
The lookup by tag function will return null if the IOCB is out of range
or does not have the on txcmplq flag set.
Fix: Check for null return from lookup by tag.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During pci hot plug, the kernel crashes in timer management code.
The sli4 remove_one handler is not stoping the timers as it starts to
remove the port so that it can be swapped.
Fix: Stop the timers early in the handler routine.
Note: Fix in SLI-4 only. SLI-3 already stopped the timers properly.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix a small cosmetic bug in a very rarely encountered error message that
can occur when a LD has a corrupted raid map.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update the driver's PCI IDs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
iscsi_session_teardown was the only user of this function. Function
currently is just short for iscsi_remove_session + iscsi_free_session.
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Session attributes exposed through sysfs were freed before the device
was destroyed, resulting in a potential use-after-free. Free these
attributes after removing the device.
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A user may lower the max_sectors_kb setting in sysfs to accommodate
certain workloads. Previously we would always set the max I/O size to
either the block layer default or the optional preferred I/O size
reported by the device.
Keep the current heuristics for the initial setting of max_sectors_kb.
For subsequent invocations, only update the current queue limit if it
exceeds the capabilities of the hardware.
Cc: <stable@vger.kernel.org>
Reported-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SBC-4 states:
"A MAXIMUM UNMAP LBA COUNT field set to a non-zero value indicates the
maximum number of LBAs that may be unmapped by an UNMAP command"
"A MAXIMUM WRITE SAME LENGTH field set to a non-zero value indicates
the maximum number of contiguous logical blocks that the device server
allows to be unmapped or written in a single WRITE SAME command."
Despite the spec being clear on the topic, some devices incorrectly
expect WRITE SAME commands with the UNMAP bit set to be limited to the
value reported in MAXIMUM UNMAP LBA COUNT in the Block Limits VPD.
Implement a blacklist option that can be used to accommodate devices
with this behavior.
Cc: <stable@vger.kernel.org>
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Reported-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight mostly minor fixes for recently discovered issues in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ILLEGAL REQUEST + ASC==27 => target failure
scsi: aacraid: Add a small delay after IOP reset
scsi: scsi_transport_fc: Also check for NOTPRESENT in fc_remote_port_add()
scsi: scsi_transport_fc: set scsi_target_id upon rescan
scsi: scsi_transport_iscsi: fix the issue that iscsi_if_rx doesn't parse nlmsg properly
scsi: aacraid: error: testing array offset 'bus' after use
scsi: lpfc: Don't return internal MBXERR_ERROR code from probe function
scsi: aacraid: Fix 2T+ drives on SmartIOC-2000
|
|
ASC 0x27 is "WRITE PROTECTED". This error code is returned e.g. by
Fujitsu ETERNUS systems under certain conditions for WRITE SAME 16
commands with UNMAP bit set. It should not be treated as a path
error. In general, it makes sense to assume that being write protected
is a target rather than a path property.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove unused variable sas_ha to clean up build warning
"unused variable sas_ha [-Wunused-variable]"
Fixes: 042ebd293b86 ("scsi: libsas: kill useless ha_event and do some cleanup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since the command type of UTRD in UFS 2.1 specification is the same with
UFS 2.0. And it assumes the future UFS specification will follow the
same definition.
Signed-off-by: kehuanlin <kehuanlin@pinecone.net>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Several configurable fields of the Device Descriptor and the Unit
Descriptors determine the Boot LUN status. The bBootEnable field and the
bBootLunEn attribute is set to zero by default, so the Boot LUN is
disabled by default.
At which point the scsi device add for Boot LUN will fail, but we can
continue to use the ufs device in fact. This failure shouldn't abort the
device boot.
Signed-off-by: Huanlin Ke <kehuanlin@pinecone.net>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Zang Leigang <zangleigang@hisilicon.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 0e9973ed3382 ("scsi: aacraid: Add periodic checks to see IOP reset
status") changed the way driver checks if a reset succeeded. Now, after an
IOP reset, aacraid immediately start polling a register to verify the reset
is complete.
This behavior cause regressions on the reset path in PowerPC (at least).
Since the delay after the IOP reset was removed by the aforementioned patch,
the fact driver just starts to read a register instantly after the reset
was issued (by writing in another register) "corrupts" the reset procedure,
which ends up failing all the time.
The issue highly impacted kdump on PowerPC, since on kdump path we
proactively issue a reset in adapter (through the reset_devices kernel
parameter).
This patch (re-)adds a delay right after IOP reset is issued. Empirically
we measured that 3 seconds is enough, but for safety reasons we delay
for 5s (and since it was 30s before, 5s is still a small amount).
For reference, without this patch we observe the following messages
on kdump kernel boot process:
[ 76.294] aacraid 0003:01:00.0: IOP reset failed
[ 76.294] aacraid 0003:01:00.0: ARC Reset attempt failed
[ 86.524] aacraid 0003:01:00.0: adapter kernel panic'd ff.
[ 86.524] aacraid 0003:01:00.0: Controller reset type is 3
[ 86.524] aacraid 0003:01:00.0: Issuing IOP reset
[146.534] aacraid 0003:01:00.0: IOP reset failed
[146.534] aacraid 0003:01:00.0: ARC Reset attempt failed
Fixes: 0e9973ed3382 ("scsi: aacraid: Add periodic checks to see IOP reset status")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
