| Age | Commit message (Collapse) | Author |
|---|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/drivers
Pull "ARM: mediatek: updates for soc drivers for v4.16-next" from Matthias Brugger:
scpsy:
- mt2712: update power domains to reflect design changes in the SoC
- fix initialisation of power subdomains
- add support for mt7623a SoC
- use defines for mt2701 bus protection mask
* tag 'v4.16-next-soc' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
soc: mediatek: update power domain data of MT2712
dt-bindings: soc: update MT2712 power dt-bindings
soc: mediatek: fix the mistaken pointer accessed when subdomains are added
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
soc: mediatek: avoid hardcoded value with bus_prot_mask
dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Pull "soc/tegra: Changes for v4.17-rc1" from Thierry Reding:
This contains more Tegra194 support as well as an implementation for the
MBIST workaround needed to avoid some memory-related issues on Tegra210.
* tag 'tegra-for-4.17-soc-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Use the new reset APIs to manage reset controllers
soc/tegra: pmc: Pass PMC to tegra_powergate_power_up()
soc/tegra: pmc: MBIST work around for Tegra210
soc/tegra: pmc: Add Tegra194 compatibility string
soc/tegra: Add Tegra194 SoC configuration option
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Renesas ARM Based SoC Updates for v4.17" from Simon Horman:
01d675f159e0 ARM: shmobile: rcar-gen2: Add watchdog support
58adf1ba0d22 ARM: shmobile: Add watchdog support
* SoC
- Identify R-Car V3H (r8a77980) and M3N (r8a77965)
- Enable R-Car Gen2 regulator quirk for Stout board with H3 (r8a7790) SoC
Marek Vaust says "Regulator setup is suboptimal on H2 Stout too. The
Stout newly has two DA9210 regulators, so the quirk is extended to
handle another DA9210 at i2c address 0x70."
- Add watchdog support
This is the SoC portion of the following solution. It is not yet
enabled in DT as it is not functional without clock dependencies
in place.
Fabrizio Castro says "this series has been around for some time as RFC,
and it has collected useful comments from the community along the way.
The solution proposed by this patch set works for most R-Car Gen2 and
RZ/G1 devices, but not all of them. We now know that for some R-Car
Gen2 early revisions there is no proper software fix. Anyway, no
product has been built around early revisions, but development boards
mounting early revisions (basically prototypes) are still out there.
As a result, this series isn't enabling the internal watchdog on R-Car
Gen2 boards, developers may enable it in board specific device trees if
needed. This series has been tested by me on the iwg20d, iwg22d,
Lager, Alt, and Koelsch boards.
The problem
===========
To deal with SMP on R-Car Gen2 and RZ/G1, we install a reset vector to
ICRAM1 and we program the [S]BAR registers so that when we turn ON the
non-boot CPUs they are redirected to the reset vector installed by Linux
in ICRAM1, and eventually they continue the execution to RAM, where the
SMP bring-up code will take care of the rest. The content of the [S]BAR
registers survives a watchdog triggered reset, and as such after the
watchdog fires the boot core will try and execute the SMP bring-up code
instead of jumping to the bootrom code.
The fix
=======
The main strategy for the solution is to let the reset vector decide if
it needs to jump to shmobile_boot_fn or to the bootrom code. In a
watchdog triggered reset scenario, since the [S]BAR registers keep their
values, the boot CPU will jump into the newly designed reset vector, the
assembly routine will eventually test WOVF (a bit in register RWTCSRA
that indicates if the watchdog counter has overflown, the value of this
bit gets retained in this scenario), and jump to the bootrom code which
will in turn load up the bootloader, etc. When bringing up SMP or using
CPU hotplug, the reset vector will jump to shmobile_boot_fn instead."
* R-Car Rst
- Add support for R-Car V3H (r8a77980) and V3H (r8a77980)
* R-Car SYSC
- Mark rcar_sysc_matches[] __initconst
Geert Uytterhoeven says "This frees another 1764 bytes
(arm32/shmobile_defconfig) or 1000 bytes (arm64/renesas_defconfig) of
memory after kernel init."
- Fix power area parents
Sergei Shtylyov says "According to the figure 9.2(b) of the R-Car
Series, 3rd Generation User’s Manual: Hardware Rev. 0.80 the A2IRn and
A2SCn power areas in R8A77970 have the A3IR area as a parent, thus the
SYSC driver has those parents wrong.."
- Add support for R-Car V3H (r8a77980) and V3H (r8a77980)
* tag 'renesas-soc-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: rcar-gen2: Add watchdog support
ARM: shmobile: Add watchdog support
ARM: shmobile: rcar-gen2: Fix error check in regulator quirk
soc: renesas: rcar-rst: Add support for R-Car M3-N
ARM: shmobile: stout: enable R-Car Gen2 regulator quirk
soc: renesas: rcar-sysc: Add R-Car M3-N support
soc: renesas: Identify R-Car M3-N
soc: renesas: rcar-sysc: add R8A77980 support
dt-bindings: power: add R8A77980 SYSC power domain definitions
soc: renesas: r8a77970-sysc: fix power area parents
soc: renesas: rcar-rst: Enable watchdog as reset trigger for Gen2
soc: renesas: rcar-rst: add R8A77980 support
soc: renesas: identify R-Car V3H
soc: renesas: rcar-sysc: Mark rcar_sysc_matches[] __initconst
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.17" from Kevin Hilman:
- AXG: add/enable UART_A, I2C, RMII, system controller, HW RNG
- accept MAC from u-boot environment
- misc. fixes
* tag 'amlogic-dt64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: make efuse read-only
ARM64: dts: meson: bump mali450 clk to 744MHz
meson-gx-socinfo: Add package id for S905H
ARM64: dts: meson-gxbb-wetek: add a wetek specific dtsi to cleanup hub and play2
ARM64: dts: meson: reduce odroid-c2 eMMC maximum rate
ARM64: dts: amlogic: Convert to new-style SPDX license identifiers
ARM64: dts: meson-axg: fix pwm_AO_cd compatible
ARM64: dts: meson-axg: add sec_AO system controller
ARM64: dts: meson: accept MAC addr from u-boot environment
ARM64: dts: meson s905x: accept MAC addr from u-boot environment
ARM64: dts: meson-axg: enable the UART_A controller
ARM64: dts: meson-axg: complete the pinctrl info for UART_AO_A
ARM64: dts: meson-axg: uart: Add the pinctrl info description
ARM64: dts: meson-axg: uart: drop legacy compatible name from EE UART
ARM64: dts: meson-axg: add RMII pins for ethernet controller
ARM64: dts: meson-axg: enable I2C Master-1 for the audio speaker
ARM64: dts: meson-axg: describe pin DT info for I2C controller
ARM64: dts: meson-axg: add I2C DT info for Meson-AXG SoC
ARM64: meson-axg: enable hardware rng
|
|
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f9524
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e61 (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updates the Amlogic Meson SoCs IDs for the Armv8 based SoCs.
It includes the new families and packages.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Make use of of_reset_control_array_get_exclusive() to manage
an array of reset controllers available with the device.
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
[p.zabel@pengutronix.de: switch to hidden reset control array]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
1. split MFG power domain into MFG/MFG_SC1/MFG_SC2/MFG_SC3
according to MT2712 ECO design change
2. add subdomain support for MT2712
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/drivers
Pull "i.MX drivers update for 4.17" from Shawn Guo:
- Set GENPD_FLAG_ALWAYS_ON flag for ARM power domain to avoid incorrect
power state in sysfs pm_genpd_summary output.
* tag 'imx-drivers-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: gpc: ARM power domain should be always-on
|
|
The wait_for_completion() call in qman_delete_cgr_safe()
was triggering a scheduling while atomic bug, replacing the
kthread with a smp_call_function_single() call to fix it.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the pointer to struct scp_subdomian not being moved forward
when each sub-domain is expected to be iteratively added through
pm_genpd_add_subdomain call.
Cc: stable@vger.kernel.org
Fixes: 53fddb1a66dd ("soc: mediatek: reduce code duplication of scpsys_probe across all SoCs")
Reported-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add SCPSYS power domain driver for MT7623A SoC. The MT7623A's power
domains are the subset of MT7623 SoC's ones. As MT7623 SoC has full
features whereas MT7623A is being designed just for router applications.
Thus, MT7623A doesn't include those power domains multimedia function
belongs to. In order to avoid certain errors undoubtedly happening at
registering those power domains on MT7623A SoC using the existing MT7623
SCPSYS driver, it's required to define another setup specifically for
MT7623A SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
use a meaningful definition for bus_prot_mask instead of just hardcoded
for it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
hdr.len includes both the size of the header and the fragment, so using
this when stepping through the firmware causes us to skip 16 bytes every
chunk of 3072 bytes; causing only the first fragment to actually be
valid data.
Instead use fragment size steps through the firmware blob.
Fixes: ea7a1f275cf0 ("soc: qcom: Introduce WCNSS_CTRL SMD client")
Reported-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
On some platform the remote processor's memory map is not statically
configured in TrustZone, so each memory region that is to be accessed by
the remote needs a call into TrustZone to set up the remote's
permissions.
Implement this for the rmtfs memory driver, to give the modem on 8996
access to the shared file system buffers.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
tegra_powergate_sequence_power_up() makes up a struct tegra_powergate
from scratch in order to reuse the same code as used by the generic PM
domain implementation. However, subsequent patches will need to access
the struct tegra_pmc * embedded in the powergate structure, so we need
to make sure we always pass it in.
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Apply the memory built-in self test work around when ungating certain
Tegra210 power domains.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra194 PMC is mostly compatible with Tegra186, including in all
currently supported features. As such, add a new compatibility string
but point to the existing Tegra186 SoC data for now.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the configuration option to enable support for the Tegra194 system-
on-chip.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The S905H can be found on the Wetek Hub and Play2 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Pull "Samsung soc drivers changes for v4.17" from Krzysztof Kozłowski:
1. Add SPDX license identifiers.
2. Populate children syscon nodes in PMU driver to properly model HW in
DeviceTree.
* tag 'samsung-drivers-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: pmu: Populate children syscon nodes
soc: samsung: Add SPDX license identifiers to headers
memory: samsung: Add SPDX license identifiers
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Add am335x and am437x PM code for v4.17" from Tony Lindgren:
This series of changes from Dave Gerlach adds the PM related
code to allow low-power suspend states. The code consists of
the SoC specific assembly code and a related PM driver.
* tag 'omap-for-v4.17/am-pm-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: Add pm33xx driver for basic suspend support
ARM: OMAP2+: pm33xx-core: Add platform code needed for PM
ARM: OMAP2+: Introduce low-level suspend code for AM43XX
ARM: OMAP2+: Introduce low-level suspend code for AM33XX
|
|
Clocks related to DISP1 block require special handling for power domain
turn on/off sequences. Till now this was handled by Exynos power domain
driver, but that approach was limited only to some special cases. This
patch moves handling of those operations to clock controller driver.
This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5250 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Clocks related to DISP, GSC and MFC blocks require special handling for
power domain turn on/off sequences. Till now this was handled by Exynos
power domain driver, but that approach was limited only to some special
cases. This patch moves handling of those operations to clock controller
driver. This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5420 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Handling of clock reparenting will be move to clock controller driver,
so add possibility to blacklist clock handling on systems, where the
clock controller already does all needed operations. This is needed
to avoid potential deadlock on clock reparenting during power domain
on/off procedure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The of_count_phandle_with_args() can fail and return error(for example,
rk3399 pd_vio doesn't have clocks). That would break the pd probe.
Add a sanity check on pd->num_clks to avoid that.
Fixes: 65084121d59d ("soc: rockchip: power-domain: use clk_bulk APIs")
Reported-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Use clk_bulk APIs, and also add error handling for clk enable.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Disable IO function switching between sdmmc and jtag
for RK3128 SoCs.
Signed-off-by: Xiao Yao <xiaoyao@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is the first set of bugfixes for ARM SoCs, fixing a couple of
stability problems, mostly on TI OMAP and Rockchips platforms:
- OMAP2 hwmod clocks must be enabled in the correct order
- OMAP3 Wakeup from resume through PRM IRQ was unreliable
- one regression on OMAP5 caused by a kexec fix
- Rockchip ethernet needs some settings for stable operation on
Rock64
- Rockchip based Chrombook Plus needs another clock setting for
stable display suspend/resume
- Rockchip based phyCORE-RK3288 was able to run at an invalid CPU
clock frequency
- Rockchip MMC link was sometimes unreliable
- multiple fixes to avoid crashes in the Broadcom STB DPFE driver
Other minor changes include:
- Devicetree fixes for incorrect hardware description (rockchip,
omap, Gemini, amlogic)
- some MAINTAINER file updates to correct email and git addresses
- some fixes addressing 'make W=1' dtc warnings (broadcom, amlogic,
cavium, qualcomm, hisilicon, zx)
- fixes for LTO-compilation (orion, davinci, clps711x)
- one fix for an incorrect Kconfig errata selection
- a memory leak in the OMAP timer driver
- a kernel data leak in OMAP1 debugfs files"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
MAINTAINERS: update entries for ARM/STM32
ARM: dts: bcm283x: Move arm-pmu out of soc node
ARM: dts: bcm283x: Fix unit address of local_intc
ARM: dts: NSP: Fix amount of RAM on BCM958625HR
ARM: dts: Set D-Link DNS-313 SATA to muxmode 0
ARM: omap2: set CONFIG_LIRC=y in defconfig
ARM: dts: imx6dl: Include correct dtsi file for Engicam i.CoreM6 DualLite/Solo RQS
memory: brcmstb: dpfe: support new way of passing data from the DCPU
memory: brcmstb: dpfe: fix type declaration of variable "ret"
memory: brcmstb: dpfe: properly mask vendor error bits
ARM: BCM: dts: Remove leading 0x and 0s from bindings notation
ARM: orion: fix orion_ge00_switch_board_info initialization
ARM: davinci: mark spi_board_info arrays as const
ARM: clps711x: mark clps711x_compat as const
arm: zx: dts: Remove leading 0x and 0s from bindings notation
arm64: dts: Remove leading 0x and 0s from bindings notation
arm64: dts: cavium: fix PCI bus dtc warnings
MAINTAINERS: ARM: at91: update my email address
soc: imx: gpc: de-register power domains only if initialized
ARM: dts: rockchip: Fix DWMMC clocks
...
|
|
AM335x and AM437x support various low power modes as documented
in section 8.1.4.3 of the AM335x Technical Reference Manual and
section 6.4.3 of the AM437x Technical Reference Manual.
DeepSleep0 mode offers the lowest power mode with limited
wakeup sources without a system reboot and is mapped as
the suspend state in the kernel. In this state, MPU and
PER domains are turned off with the internal RAM held in
retention to facilitate the resume process. As part of
the boot process, the assembly code is copied over to OCMCRAM
so it can be executed to turn of the EMIF and put DDR into self
refresh.
Both platforms have a Cortex-M3 (WKUP_M3) which assists the MPU
in DeepSleep0 entry and exit. WKUP_M3 takes care
of the clockdomain and powerdomain transitions based on the
intended low power state. MPU needs to load the appropriate
WKUP_M3 binary onto the WKUP_M3 memory space before it can
leverage any of the PM features like DeepSleep. This loading
is handled by the remoteproc driver wkup_m3_rproc.
Communication with the WKUP_M3 is handled by a wkup_m3_ipc
driver that exposes the specific PM functionality to be used
the PM code.
In the current implementation when the suspend process
is initiated, MPU interrupts the WKUP_M3 to let it know about
the intent of entering DeepSleep0 and waits for an ACK. When
the ACK is received MPU continues with its suspend process
to suspend all the drivers and then jumps to assembly in
OCMC RAM. The assembly code puts the external RAM in self-refresh
mode, gates the MPU clock, and then finally executes the WFI
instruction. Execution of the WFI instruction with MPU clock gated
triggers another interrupt to the WKUP_M3 which then continues
with the power down sequence wherein the clockdomain and
powerdomain transition takes place. As part of the sleep sequence,
WKUP_M3 unmasks the interrupt lines for the wakeup sources. WFI
execution on WKUP_M3 causes the hardware to disable the main
oscillator of the SoC and from here system remains in sleep state
until a wake source brings the system into resume path.
When a wakeup event occurs, WKUP_M3 starts the power-up
sequence by switching on the power domains and finally
enabling the clock to MPU. Since the MPU gets powered down
as part of the sleep sequence in the resume path ROM code
starts executing. The ROM code detects a wakeup from sleep
and then jumps to the resume location in OCMC which was
populated in one of the IPC registers as part of the suspend
sequence.
Code is based on work by Vaibhav Bedia.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
On lkml suggestions were made to split up such trivial typo fixes into per subsystem
patches:
--- a/arch/x86/boot/compressed/eboot.c
+++ b/arch/x86/boot/compressed/eboot.c
@@ -439,7 +439,7 @@ setup_uga32(void **uga_handle, unsigned long size, u32 *width, u32 *height)
struct efi_uga_draw_protocol *uga = NULL, *first_uga;
efi_guid_t uga_proto = EFI_UGA_PROTOCOL_GUID;
unsigned long nr_ugas;
- u32 *handles = (u32 *)uga_handle;;
+ u32 *handles = (u32 *)uga_handle;
efi_status_t status = EFI_INVALID_PARAMETER;
int i;
This patch is the result of the following script:
$ sed -i 's/;;$/;/g' $(git grep -E ';;$' | grep "\.[ch]:" | grep -vwE 'for|ia64' | cut -d: -f1 | sort | uniq)
... followed by manual review to make sure it's all good.
Splitting this up is just crazy talk, let's get over with this and just do it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If power domain information are missing in the device tree, no
power domains get initialized. However, imx_gpc_remove tries to
remove power domains always in the old DT binding case. Only
remove power domains when imx_gpc_probe initialized them in
first place.
Fixes: 721cabf6c660 ("soc: imx: move PGC handling to a new GPC driver")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for R-Car M3-N (R8A77965) power areas.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for indentifying R-Car M3-N (R8A77965) SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for R-Car V3H (R8A77980) SoC power areas to the R-Car SYSC
driver.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to the figure 9.2(b) of the R-Car Series, 3rd Generation User’s
Manual: Hardware Rev. 0.80 the A2IRn and A2SCn power areas in R8A77970 have
the A3IR area as a parent, thus the SYSC driver has those parents wrong...
Fixes: bab9b2a74fe9 ("soc: renesas: rcar-sysc: add R8A77970 support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch allows for platform specific quirks as some of the SoC need
further customization for the watchdog to work properly, like for R-Car
Gen2 and for RZ/G.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The syscon poweroff and restart nodes logically belong to the Power
Management Unit so populate possible children.
This also requires providing compatibles for Exynos5410 and Exynos7 so
the PMU device and its children will be instantiated for them as well.
Just like Exynos5433, these chipsets are not yet supported by the PMU
driver.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Fixes the following sparse warnings:
drivers/soc/amlogic/meson-gx-socinfo.c:100:12: warning:
symbol 'meson_gx_socinfo_init' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Fixes the following sparse warnings:
drivers/soc/amlogic/meson-mx-socinfo.c:107:12: warning:
symbol 'meson_mx_socinfo_init' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
powered off
When operating the system headless headless, the domain is never
powered on, leaving the clocks disabled. The shutdown function then
tries to disable the already disabled clocks, resulting in errors.
Therefore call meson_gx_pwrc_vpu_power_off() only if domain is
powered on.
This patch fixes the described issue on my system (Odorid-C2).
Fixes: 339cd0ea0822 "soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The error message may be misleading in case of probe deferral
(happens on my Odroid-C2). Therefore don't print it in this case.
Fixes: 75fcb5ca4b46 "soc: amlogic: add Meson GX VPU Domains driver"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Changes since v1:
Added changes in these files:
drivers/infiniband/hw/usnic/usnic_transport.c
drivers/staging/lustre/lnet/lnet/lib-socket.c
drivers/target/iscsi/iscsi_target_login.c
drivers/vhost/net.c
fs/dlm/lowcomms.c
fs/ocfs2/cluster/tcp.c
security/tomoyo/network.c
Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.
"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.
None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.
This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.
Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.
rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.
Userspace API is not changed.
text data bss dec hex filename
30108430 2633624 873672 33615726 200ef6e vmlinux.before.o
30108109 2633612 873672 33615393 200ee21 vmlinux.o
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to implement support for grabbing core dumps in remoteproc it's
necessary to know the relocated base of the image, as the offsets from
the virtual memory base might not be based on the physical address.
Return the adjusted physical base address to the caller.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add support for R-Car V3H (R8A77980) to the R-Car RST driver -- this driver
is needed for the clock driver to work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for identifying the R-Car V3H (R8A77980) SoC.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
rcar_sysc_matches[] is used only by rcar_sysc_pd_init(), which is
__init. Hence mark rcar_sysc_matches[] __initconst.
This frees another 1764 bytes (arm32/shmobile_defconfig) or 1000 bytes
(arm64/renesas_defconfig) of memory after kernel init.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Disable IO function switching between sdmmc and jtag
for RK3228 and RK3229 SoCs.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
