| Age | Commit message (Collapse) | Author |
|---|
|
The error handler calls sci_rx_interrupt() to drain the receive FIFO if
an error condition happens.
However, if DMA is enabled on SCIFA or SCIFB, this will call
disable_irq_nosync() twice. Due to this imbalance, the receive interrupt
will never be re-enabled, and reception stops forever.
To fix this, restrict draining the FIFO to PIO mode, and just call
sci_receive_chars() directly.
Inspired by a patch from Yoshihiro Shimoda
<yoshihiro.shimoda.uh@renesas.com>.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes an issue that this driver causes a NULL pointer
dereference in the following conditions:
- CONFIG_HIGHMEM and CONFIG_SERIAL_SH_SCI_DMA are enabled
- This driver runs on the sci_dma_rx_push()
This issue was caused by virt_to_page(buf) in the sci_request_dma()
because this driver didn't check if the "buf" was valid or not. So,
this patch uses the "buf" from dma_alloc_coherent() as is, not page.
This patch also fixes a WARNING issue in sci_rx_dma_release():
WARNING: CPU: 0 PID: 1328 at lib/dma-debug.c:1125 check_unmap+0x444/0x848()
rcar-dmac e6700000.dma-controller: DMA-API: device driver frees DMA memory with different CPU address [device address=0x000000006dd89000] [size=64 bytes] [cpu alloc address=0x000000016189c000] [cpu free address=0x0000000080000000]
WARNING: CPU: 1 PID: 1 at drivers/base/dma-mapping.c:334 dma_common_free_remap+0x48/0x6c()
trying to free invalid coherent area: (null)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert] Rebased
[geert] Reworded
[geert] Dropped .rx_chunk, as it's always identical to .rx_buf[0]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's no need to keep all buffer and DMA pointers on the stack.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switch from using tty_buffer_request_room() and looping over
tty_insert_flip_char() to tty_insert_flip_string().
Keep track of buffer overruns in the icount structure, like
serial_core.c does.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently sci_dma_rx_push() has to find the active scatterlist itself,
but in some cases the caller already knows.
Hence let the caller pass the scatterlist, and introduce a helper to
find the active DMA request while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During serial port shutdown, the DMA receive worker function may still
be called after the receive DMA cleanup function has been called.
Fix this race condition between work_fn_rx() and sci_rx_dma_release() by
acquiring the port's spinlock in sci_rx_dma_release().
This requires releasing the spinlock in work_fn_rx() before calling (any
function that may call) sci_rx_dma_release().
Terminate all active receive DMA descriptors to release them, and to
make sure no more completions come in.
Do the same in sci_tx_dma_release() for symmetry, although the serial
upper layer will no longer submit more data at this point of time.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a problem when the sci_dma_rx_complete() is processed
before cancel process of work_fn_rx() completes by rx_timer_fn().
This patch locks work_fn_rx().
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resubmission of DMA descriptors is explicitly forbidden by the DMA
engine API.
Hence pass DMA_CTRL_ACK to dmaengine_prep_slave_sg(), and prepare a new
DMA descriptor instead of reusing the old one.
Remove sci_port.desc_rx[], as there's no longer a need to access the
active descriptor.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Simplify the error handling in sci_submit_rx() by
- Moving it to the end of the function,
- Just calling dmaengine_terminate_all() instead of calling
async_tx_ack() for all already submitted descriptors.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As dmaengine_prep_slave_sg() is called with the DMA_CTRL_ACK flag set
for DMA transmit requests, there's no need to explicitly acknowledge DMA
transmit requests in the DMA transmit completion callback.
Hence remove the call to async_tx_ack(), and remove the now unused
dma_async_tx_descriptor pointer in the sci_port structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert the SCI driver from the SHDMAE-specific partial DMA transfer
handling to the generic dmaengine residual data framework.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace open-coded
- calls to dma_async_tx_descriptor.tx_submit() by calls to the
dmaengine_submit() helper,
- dma_cookie_t comparisons by calls to dma_submit_error().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The mapped transmit buffer is never unmapped. This leaks quite some
mappings, as the mapping is done in uart_ops.startup(), i.e. every time
the device is opened. Unmap the buffer on device close.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Simplify the DMA transmit code by using dma_map_single() instead of
constantly modifying the single-entry scatterlist to match what's
currently being transmitted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When comparing differently sized types, it's better to use
min_t()/max_t() than adding casts.
Also use "unsigned int" instead of "int", as that's the right type for
the length of an SG entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To function correctly in the presence of an IOMMU, the DMA buffers must
be managed using the DMA channel's device instead of the platform
device's device.
Make sure to free the DMA memory before releasing the channel, not
after.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Let sci_request_dma() handle failures to initialize DMA itself.
This way sci_tx_dma_release() and sci_rx_dma_release() don't have to
consider partial initialization, and thus don't need to reset DMA
addresses to DMA_ERROR_CODE, which is not 100% portable access
architectures.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Reformat, grammar improvements, use "ms" instead of "msec".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make the life of the driver developer/debugger easier:
- Add __func__ prefix to identical messages,
- Add DMA directions to messages,
- Add TX failure messages,
- Always use "cookie %d" for DMA cookies,
- "#%d" is reserved for the DMA cookie/descriptor index.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fix an issue that the driver may cause "nobody cared" IRQ
when this driver detects the overrun flag only.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 8b6ff84c2d445a47 ("serial: sh-sci: Fix R-Car SCIF and HSCIF
overrun handling") added overrun handling for (H)SCIF using the SCLSR
register, but also accidentally added a bogus call to
sci_handle_fifo_overrun() in the receive interrupt path.
Remove it again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Printing an error on memory allocation failures is unnecessary.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Reorder sampling_rate assignment for consistency in all cases of the
switch statement.
Avoid using the ternary conditional operator to make it more clear that
the value is overridden by platform data.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
serial_core.c was moved from drivers/serial/ to drivers/tty/serial/ a
while ago. Remove the path to make it move-proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SCIF_ERROR_CLEAR includes SCIFA_ORER, which exists only on SCIFA/SCIFB
and SCIF on sh7705/sh7720/sh7721.
To fix this:
1. Remove SCIFA_ORER from the definition of SCIF_ERROR_CLEAR,
2. During initialization, store the error clear mask to use,
incorporating the overrun bit only if it applies to the SCxSR
register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Expressions involving "BIT(...)" create values of type "long", which is
64-bit on 64-bit. Hence "~BIT(...)" no longer fits in 32-bit, which
will cause future compiler warnings when assigning to 32-bit variables:
drivers/tty/serial/sh-sci.c: In function 'sci_init_single':
drivers/tty/serial/sh-sci.h:58:25: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define SCI_ERROR_CLEAR ~(SCI_RESERVED | SCI_PER | SCI_FER | SCI_ORER)
^
drivers/tty/serial/sh-sci.c:2325:27: note: in expansion of macro 'SCI_ERROR_CLEAR'
sci_port->error_clear = SCI_ERROR_CLEAR;
As these values are (at most) 32-bit register values anyway, cast them
to "u32" at the definition level to prevent such compiler warnings.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The #ifdef logic to clear SCxSR bits using RMW on SCIFA/SCIFB and SCIF
variants with some SCIFA features (sh7705/SH7720/sh7721) has several
drawbacks:
- It wasn't updated for newer R-Mobile variants (APE6),
- It doesn't correctly handle SoCs with both SCIF and SCIFA/B (e.g.
R-Car Gen2, but also legacy sh7723/sh7724),
- It doesn't play well with ARM multi-platform kernels: on R-Car Gen2,
SCIF/SCIFA/SCIFB/HSCIF were handled differently, depending on
whether r8a7740 or sh73a0 support was enabled or not,
Replace the #ifdef logic by runtime logic to fix this.
SCIFA/SCIFB and SCIF on sh7705/sh7720/sh7721 use RMW to clear error
bits, other variants use plain stores, as before.
Note that this changes behavior for SCIFA on sh7723/sh7724 (these SoCs
have both SCIF and SCIFA), which didn't use RMW before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The following race conditions can happen when a serial port is used
as console.
Case1: CPU_B is used to detect an interrupt from a serial port,
but it can have interrupts disabled during the waiting time.
Case2: CPU_B clears UART_IER just after CPU_A sets UART_IER and then
a serial port may not make an interrupt.
Case3: CPU_A sets UART_IER just after CPU_B clears UART_IER.
This is an unexpected behavior for serial8250_console_write().
CPU_A [autoconfig_irq] | CPU_B [serial8250_console_write]
----------------------------|---------------------------------------
|
probe_irq_on() | spin_lock_irqsave(&port->lock,)
serial_outp(,UART_IER,0x0f) | serial_out(,UART_IER,0)
udelay(20); | uart_console_write()
probe_irq_off() |
| spin_unlock_irqrestore(&port->lock,)
Case1 and 2 can make autoconfig_irq() failed.
In these cases, the console doesn't work in interrupt mode and
"input overrun" (which can make operation mistakes) can happen
on some systems. Especially in the Case1, It is known that the
problem happens with high rate every boot once it occurs
because the boot sequence is always almost same.
port mutex makes sure that the autoconfig operation is exclusive of
any other concurrent HW access except by the console operation.
console lock is required in autoconfig_irq().
Signed-off-by: Taichi Kageyama <t-kageyama@cp.jp.nec.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes receiving broken characters on the console from an MPC5125
system when systemd comes up which repeatedly opens and shuts down the
console device.
Trial and error with the needed interval showed that 500 us are good
enough most of the time when using 38400 Bd, so I think 1 ms is a good
compromise between fixing the issue and not penalize faster setups too
much.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kconfig currently controlling compilation of this code is:
8250/Kconfig:config SERIAL_8250_LPC18XX
8250/Kconfig: bool "NXP LPC18xx/43xx serial port support"
...meaning that it currently is not being built as a module by anyone.
When targetting orphaned modular code in non-modular drivers, this
came up. Joachim indicated that the driver was actually meant to
be tristate but ended up bool by accident. So here we make it
tristate instead of removing the modular code that was essentially
orphaned.
Suggested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kconfig for this driver is currently:
config SERIAL_MPSC
bool "Marvell MPSC serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We leave some tags like MODULE_AUTHOR for documentation purposes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CIR type serial ports aren't real serial ports.
This is just a way to prevent legacy 8250 serial
driver from probing and eventually binding some
resources.
Since in current state such ports aren't providing
any real functionality and it is not possible
to change their type via setserial/ioctl(TIOCSSERIAL)
(due to UPF_FIXED_PORT flag set on them)
it is simpler and cleaner to not register them at all
with serial core.
Print a short message in this case so it is known
to user what has happened.
This way checks for PORT_8250_CIR in serial port
callbacks can be removed too, since they won't
ever be called.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function tty_insert_flip_string() returns an int and as such it
might fail. So the result is that I kindly asked to insert 48 bytes and
the function only insterted 32.
I have no idea what to do with the remaining 16 so I think dropping them
is the only option. I also increase the buf_overrun counter so userpace
has a clue that we lost bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
* clk-fixes: (3 commits)
clk: ti: dflt: fix enable_reg validity check
clk: ti: fix dual-registration of uart4_ick
clk: ti: clk-7xx: Remove hardwired ABE clock configuration
|
|
We have couple of standard but rare used baudrates which are not supported by
1,8432MHz reference frequency. Besides that user can potentially ask for any
baudrate (via BOTHER flag) and we currently don't fully support that. Since
clk-fractional-divider is moved to use rational best approximation for
reference frequency we may amend the driver to support whatever user wants.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The split of the 8250 driver into a 8250_base/8250.ko resulted in a
lack of a license for the 8250_base.ko module. This caused the module
to fail to load and the kernel to be tainted. Add the appropriate
MODULE_LICENSE to 8250_port.c, which is always compiled into
8250_base.ko
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty driver reverts from Greg KH:
"Here are some reverts for some tty patches (specifically the pl011
driver) that ended up breaking a bunch of machines (i.e. almost all
of the ones with this chip).
People are working on a fix for this, but in the meantime, it's best
to just revert all 5 patches to restore people's serial consoles.
These reverts have been in linux-next for many days now"
* tag 'tty-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "uart: pl011: Rename regs with enumeration"
Revert "uart: pl011: Introduce register accessor"
Revert "uart: pl011: Introduce register look up table"
Revert "uart: pl011: Improve LCRH register access decision"
Revert "uart: pl011: Add support to ZTE ZX296702 uart"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
|
|
This reverts commit 534e14e2293d8cd714b94513686228453b21fae2 as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 7b753f318d1456c8e7740f3bd96d1dbb362d5449 as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2c096a9eedc6841d3610545f4e6c3d72bd0962be as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 09dcc7dfc05b31bf0bbcd1511cd1a2644908d5c8 as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 8cd90e50d1408c65c355084b1c7f8f9085f49c6b as with
this patch the serial console is broken on lots of platforms.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change teaches the imx serial driver to save its
context and restore it across suspend and resume path.
To do so, it introduces serial_imx_restore_context()
and serial_imx_save_context() functions. They use
a shadow set of registers to save key registers
and restore them accordingly. These functions can
be reused on other situations, when the device
context is lost.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch sets RTSDEN bit when going into idle (Stop mode).
We add the RTSDEN for the case RTS is sent from
the remote connection. This way we allow the system
to wakeup when RTS is received.
Cc: Fabio Stevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change is a code reorganization. Here we introduce
serial_imx_enable_wakeup() helper function to do
the job of configuring and preparing wakeup sources
on imx serial device. The idea is to allow other
parts of the code to call this function whenever
the device is known to go to idle.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
