summaryrefslogtreecommitdiff
path: root/drivers/tty/serial
AgeCommit message (Collapse)Author
2023-04-20serial: max310x: fix IO data corruption in batched operationsJan Kundrát
After upgrading from 5.16 to 6.1, our board with a MAX14830 started producing lots of garbage data over UART. Bisection pointed out commit 285e76fc049c as the culprit. That patch tried to replace hand-written code which I added in 2b4bac48c1084 ("serial: max310x: Use batched reads when reasonably safe") with the generic regmap infrastructure for batched operations. Unfortunately, the `regmap_raw_read` and `regmap_raw_write` which were used are actually functions which perform IO over *multiple* registers. That's not what is needed for accessing these Tx/Rx FIFOs; the appropriate functions are the `_noinc_` versions, not the `_raw_` ones. Fix this regression by using `regmap_noinc_read()` and `regmap_noinc_write()` along with the necessary `regmap_config` setup; with this patch in place, our board communicates happily again. Since our board uses SPI for talking to this chip, the I2C part is completely untested. Fixes: 285e76fc049c ("serial: max310x: use regmap methods for SPI batch operations") Cc: stable@vger.kernel.org Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz> Link: https://lore.kernel.org/r/79db8e82aadb0e174bc82b9996423c3503c8fb37.1680732084.git.jan.kundrat@cesnet.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20serial: core: Disable uart_start() on uart_remove_one_port()Tony Lindgren
While rebinding a uart device in a loop I noticed we may see a tx related race on uart_remove_one_port(): uart_write from n_tty_write n_tty_write from file_tty_write.constprop.0 file_tty_write.constprop.0 from vfs_write vfs_write from ksys_write ksys_write from ret_fast_syscall Let's disallow tx on port->UPF_DEAD. This flag gets set before we start tearing down the port in uart_remove_one_port(). Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20230419115423.59957-1-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20serial: 8250: Reinit port->pm on port specific driver unbindTony Lindgren
When we unbind a serial port hardware specific 8250 driver, the generic serial8250 driver takes over the port. After that we see an oops about 10 seconds later. This can produce the following at least on some TI SoCs: Unhandled fault: imprecise external abort (0x1406) Internal error: : 1406 [#1] SMP ARM Turns out that we may still have the serial port hardware specific driver port->pm in use, and serial8250_pm() tries to call it after the port specific driver is gone: serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base] uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base] uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c __tty_hangup.part.0 from disassociate_ctty+0x154/0x20c disassociate_ctty from do_exit+0x744/0xaac do_exit from do_group_exit+0x40/0x8c do_group_exit from __wake_up_parent+0x0/0x1c Let's fix the issue by calling serial8250_set_defaults() in serial8250_unregister_port(). This will set the port back to using the serial8250 default functions, and sets the port->pm to point to serial8250_pm. Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20230418101407.12403-1-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20serial: 8250: Add missing wakeup event reportingFlorian Fainelli
An 8250 UART configured as a wake-up source would not have reported itself through sysfs as being the source of wake-up, correct that. Fixes: b3b708fa2780 ("wake up from a serial port") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230414170241.2016255-1-f.fainelli@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platformSherry Sun
For lpuart32 platforms, UARTMODIR register is used instead of UARTMODEM. So here should configure the corresponding UARTMODIR register bits to avoid confusion. Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230414022111.20896-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20tty: serial: fsl_lpuart: adjust buffer length to the intended sizeShenwei Wang
Based on the fls function definition provided below, we should not subtract 1 to obtain the correct buffer length: fls(0) = 0, fls(1) = 1, fls(0x80000000) = 32. Fixes: 5887ad43ee02 ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Link: https://lore.kernel.org/r/20230410195555.1003900-1-shenwei.wang@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20serial: fix TIOCSRS485 lockingJohan Hovold
The RS485 multipoint addressing support for some reason added a new ADDRB termios cflag which is (only!) updated from one of the RS485 ioctls. Make sure to take the termios rw semaphore for the right ioctl (i.e. set, not get). Fixes: ae50bb275283 ("serial: take termios_rwsem for ->rs485_config() & pass termios as param") Cc: stable@vger.kernel.org # 6.0 Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20230412124811.11217-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20serial: make SiFive serial drivers depend on ARCH_ symbolsConor Dooley
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the use of such symbols on other architectures, convert the SiFive serial driver Kconfig entries from the SOC_ symbols to ARCH_ instead. Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20230406-carnival-aspirate-fcf69a30078c@spud Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20tty: serial: simplify qcom_geni_serial_send_chunk_fifo()Jiri Slaby (SUSE)
* use memcpy() instead of the loop (removes c variable) * use remaining parameter directly (removes chunk variable) The code is simpler and easier to follow. Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Konrad Dybcio <konrad.dybcio@linaro.org> Cc: linux-arm-msm@vger.kernel.org Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Link: https://lore.kernel.org/r/20230420093514.13055-1-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-10Merge 6.3-rc6 into tty-nextGreg Kroah-Hartman
We need the tty/serial fixes in here for testing. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-06serial: 8250_tegra: Add explicit include for of.hRob Herring
With linux/acpi.h no longer implicitly including of.h, add an explicit include of of.h to fix the following error: drivers/tty/serial/8250/8250_tegra.c:68:15: error: implicit declaration of function 'of_alias_get_id' [-Werror=implicit-function-declaration] Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2023-03-29tty: serial: sh-sci: Fix Rx on RZ/G2L SCIBiju Das
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI IPs on the SH platform. Currently, it does regshift and configuring Rx wrongly. Drop adding regshift for RZ/G2L alike SoCs. Fixes: dfc80387aefb ("serial: sh-sci: Compute the regshift value for SCI ports") Cc: stable@vger.kernel.org Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29tty: serial: fsl_lpuart: fix crash in lpuart_uport_is_activeSherry Sun
For serdev framework, tty->dev is a NULL pointer, lpuart_uport_is_active calling device_may_wakeup() may cause kernel NULL pointer crash, so here add the NULL pointer check before using it. Fixes: 4f5cb8c5e915 ("tty: serial: fsl_lpuart: enable wakeup source for lpuart") Cc: stable <stable@kernel.org> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230323110923.24581-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29tty: serial: fsl_lpuart: avoid checking for transfer complete when ↵Sherry Sun
UARTCTRL_SBK is asserted in lpuart32_tx_empty According to LPUART RM, Transmission Complete Flag becomes 0 if queuing a break character by writing 1 to CTRL[SBK], so here need to avoid checking for transmission complete when UARTCTRL_SBK is asserted, otherwise the lpuart32_tx_empty may never get TIOCSER_TEMT. Commit 2411fd94ceaa("tty: serial: fsl_lpuart: skip waiting for transmission complete when UARTCTRL_SBK is asserted") only fix it in lpuart32_set_termios(), here also fix it in lpuart32_tx_empty(). Fixes: 380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support") Cc: stable <stable@kernel.org> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230323054415.20363-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29serial: 8250: Prevent starting up DMA Rx on THRI interruptIlpo Järvinen
Hans de Goede reported Bluetooth adapters (HCIs) connected over an UART connection failed due corrupted Rx payload. The problem was narrowed down to DMA Rx starting on UART_IIR_THRI interrupt. The problem occurs despite LSR having DR bit set, which is precondition for attempting to start DMA Rx in the first place. From a debug patch: [x.807834] 8250irq: iir=cc lsr+saved=60 received=0/15 ier=0f dma_t/rx/err=0/0/0 [x.808676] 8250irq: iir=c2 lsr+saved=61 received=0/0 ier=0f dma_t/rx/err=0/0/0 [x.808776] 8250irq: iir=cc lsr+saved=60 received=1/12 ier=0d dma_t/rx/err=0/1/0 [x.808870] Bluetooth: hci0: Frame reassembly failed (-84) In the debug snippet, received field indicates 1 byte was transferred over DMA and 12 bytes after that with the non-DMA Rx. The sole byte DMA handled was corrupted (gets zeroed) which leads to the HCI failure. This problem became apparent after commit e8ffbb71f783 ("serial: 8250: use THRE & __stop_tx also with DMA") changed Tx stop behavior. Tx stop is now triggered from a THRI interrupt. Despite that this problem looks like a HW bug, this fix is not adding UART_BUG_xx flag to the driver beucase it seems useful in general to avoid starting DMA when there are only a few bytes to transfer. Skipping DMA for small transfers avoids the extra overhead DMA incurs. Thus, don't setup DMA Rx on UART_IIR_THRI but leave it to a subsequent interrupt which has Rx a related IIR value. By returning false from handle_rx_dma(), the DMA vs non-DMA decision is postponed until either UART_IIR_RDI (FIFO threshold worth of bytes awaiting) or UART_IIR_TIMEOUT (inter-character timeout) triggers at a later time which allows better to discern whether the number of bytes warrants starting DMA or not. Reported-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Fixes: e8ffbb71f783 ("serial: 8250: use THRE & __stop_tx also with DMA") Cc: stable@vger.kernel.org Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230317103034.12881-1-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29tty: serial: sh-sci: Fix transmit end interrupt handlerBiju Das
The fourth interrupt on SCI port is transmit end interrupt compared to the break interrupt on other port types. So, shuffle the interrupts to fix the transmit end interrupt handler. Fixes: e1d0be616186 ("sh-sci: Add h8300 SCI") Cc: stable <stable@kernel.org> Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230317150403.154094-1-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29serial: 8250: Fix serial8250_tx_empty() race with DMA TxIlpo Järvinen
There's a potential race before THRE/TEMT deasserts when DMA Tx is starting up (or the next batch of continuous Tx is being submitted). This can lead to misdetecting Tx empty condition. It is entirely normal for THRE/TEMT to be set for some time after the DMA Tx had been setup in serial8250_tx_dma(). As Tx side is definitely not empty at that point, it seems incorrect for serial8250_tx_empty() claim Tx is empty. Fix the race by also checking in serial8250_tx_empty() whether there's DMA Tx active. Note: This fix only addresses in-kernel race mainly to make using TCSADRAIN/FLUSH robust. Userspace can still cause other races but they seem userspace concurrency control problems. Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine") Cc: stable@vger.kernel.org Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230317113318.31327-3-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29serial: sb1250-duart: clean up after SIBYTE_BCM1x55 removalLukas Bulwahn
With commit b984d7b56dfc ("MIPS: sibyte: Remove unused config option SIBYTE_BCM1x55"), an #if in the Broadcom SiByte DUART driver can be simplified. Simplify the prepreprocessor condition after config SIBYTE_BCM1x55 removal. Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20230323071053.417-1-lukas.bulwahn@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29serial: bcm63xx-uart: add polling supportArend van Spriel
The tty framework can support polling console to allow operation in situations where interrupts are turned off. Adding polling mode support allows using KGDB over serial console, Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Link: https://lore.kernel.org/r/20230322223956.84647-1-arend.vanspriel@broadcom.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29tty: serial: sh-sci: Remove setting {src,dst}_{addr,addr_width} based on DMA ↵Biju Das
direction The direction field in the DMA config is deprecated. The sh-sci driver sets {src,dst}_{addr,addr_width} based on the DMA direction and it results in dmaengine_slave_config() failure as RZ DMAC driver validates {src,dst}_addr_width values independent of DMA direction. Fix this issue by passing both {src,dst}_{addr,addr_width} values independent of DMA direction. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230322074717.6057-1-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29serial: cpm_uart: Use uart_circ_empty()Ilpo Järvinen
Use uart_circ_empty() instead of open coding it. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230320135009.47170-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29serial: ucc_uart: Use uart_circ_empty()Ilpo Järvinen
Use uart_circ_empty() rather than open coding it. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230320135009.47170-1-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29serial: imx: remove unused imx_uart_is_imx* functionsTom Rix
clang with W=1 reports drivers/tty/serial/imx.c:292:19: error: unused function 'imx_uart_is_imx21' [-Werror,-Wunused-function] static inline int imx_uart_is_imx21(struct imx_port *sport) ^ drivers/tty/serial/imx.c:297:19: error: unused function 'imx_uart_is_imx53' [-Werror,-Wunused-function] static inline int imx_uart_is_imx53(struct imx_port *sport) ^ drivers/tty/serial/imx.c:302:19: error: unused function 'imx_uart_is_imx6q' [-Werror,-Wunused-function] static inline int imx_uart_is_imx6q(struct imx_port *sport) ^ These static functions are not used, so remove them. Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230317205710.1672232-1-trix@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29tty: serial: remove obsolete config SERIAL_SAMSUNG_UARTS_4Lukas Bulwahn
Commit 1ea35b355722 ("ARM: s3c: remove s3c24xx specific hacks"), allows simplifying the whole config logic for SERIAL_SAMSUNG_UARTS, and did this config simplification. However, it misses that SERIAL_SAMSUNG_UARTS_4's effect was just to control SERIAL_SAMSUNG_UARTS, and with the commit's change, the config SERIAL_SAMSUNG_UARTS_4 has no remaining effect and can be deleted. Remove this obsolete config SERIAL_SAMSUNG_UARTS_4. Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20230317071538.29366-1-lukas.bulwahn@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29tty: serial: qcom-geni-serial: Add a poll_init() functionDouglas Anderson
On sc7180 Chromebooks, I did the following: * Didn't enable earlycon in the kernel command line. * Didn't enable serial console in the kernel command line. * Didn't enable an agetty or any other client of "/dev/ttyMSM0". * Added "kgdboc=ttyMSM0" to the kernel command line. After I did that, I tried to enter kdb with this command over an ssh session: echo g > /proc/sysrq-trigger When I did that the system just hung. Although I thought I'd tested this scenario before, I couldn't go back and find a time when it was working. Previous testing must have relied on either the UART acting as the kernel console or an agetty running. It turns out to be pretty easy to fix: we can just use qcom_geni_serial_port_setup() as the .poll_init() function. This, together with the patch ("serial: uart_poll_init() should power on the UART"), allows the debugger to work even if there are no other users of the serial port. Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20230316132027.RESEND.2.Ie678853bb101091afe78cc8c22344bf3ff3aed74@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29serial: uart_poll_init() should power on the UARTDouglas Anderson
On Qualcomm devices which use the "geni" serial driver, kdb/kgdb won't be very happy if you use it but the resources of the port haven't been powered on. Today kdb/kgdb rely on someone else powering the port on. This could be the normal kernel console or an agetty running. Let's fix this to explicitly power things on when setting up a polling driver. Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20230316132027.RESEND.1.I106c39498d8094c6f5e7ada42c7db17aa5c64e48@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-20Merge 6.3-rc3 into tty-nextGreg Kroah-Hartman
We need the tty/serial fixes in here and it resolves a merge conflict with: drivers/tty/serial/8250/8250_em.c Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-19Merge tag 'tty-6.3-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver fixes from Greg KH: "Here are some small tty and serial driver fixes for 6.3-rc3 to resolve some reported issues. They include: - 8250 driver Kconfig issue pointed out by you that showed up in -rc1 - qcom-geni serial driver fixes - various 8250 driver fixes for reported problems - fsl_lpuart driver fixes - serdev fix for regression in -rc1 - vt.c bugfix All have been in linux-next for over a week with no reported problems" * tag 'tty-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: tty: vt: protect KD_FONT_OP_GET_TALL from unbound access serial: qcom-geni: drop bogus uart_write_wakeup() serial: qcom-geni: fix mapping of empty DMA buffer serial: qcom-geni: fix DMA mapping leak on shutdown serial: qcom-geni: fix console shutdown hang serdev: Set fwnode for serdev devices tty: serial: fsl_lpuart: fix race on RX DMA shutdown serial: 8250_pci1xxxx: Disable SERIAL_8250_PCI1XXXX config by default serial: 8250_fsl: fix handle_irq locking serial: 8250_em: Fix UART port type serial: 8250: ASPEED_VUART: select REGMAP instead of depending on it tty: serial: fsl_lpuart: skip waiting for transmission complete when UARTCTRL_SBK is asserted Revert "tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency"
2023-03-17serial: 8250_bcm7271: Fix arbitration handlingDoug Berger
The arbitration of the UART DMA is mishandled for a few exceptional cases when probing and releasing the driver. It is possible that the DMA register spaces are not defined in device tree for an instance of the driver, so attempts to access the registers in brcmuart_arbitration() would use NULL pointers. It is also possible for the probe function to return an error while still holding the UART DMA. This would prevent the UART DMA from being claimed by an instance that could use it. These errors are addressed by only releasing the UART DMA if it is held by this instance (i.e. priv->dma_enabled == 1) and directing early error paths in probe to this common release_dma handling. Fixes: 41a469482de2 ("serial: 8250: Add new 8250-core based Broadcom STB driver") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230309190224.687380-1-opendmb@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-17serial: Remove uart_wait_until_sent() forward declarationIlpo Järvinen
Remove unnecessary forward declaration of uart_wait_until_sent(). Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230309080923.11778-9-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-17serial: Rename hw_stopped to old_hw_stopped & improve logicIlpo Järvinen
hw_stopped in uart_change_line_settings() stores old hw_stopped, thus rename it appropriately. Alter logic to check first if the hw_stopped was changed, and then pick which function to call if it was because the logic is more obvious that way. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230309080923.11778-8-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-17serial: Make hw_stopped boolIlpo Järvinen
Convert hw_stopped in uart_port to bool because its more appropriate type for how it is used. Also convert the local variable in uart_change_line_settings() caching old hw_stopped to bool. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230309080923.11778-7-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-17serial: Rename uart_change_speed() to uart_change_line_settings()Ilpo Järvinen
uart_change_speed() changes more than just speed so rename it to more generic uart_change_line_settings(). Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230309080923.11778-6-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-17serial: Move uart_change_speed() earlierIlpo Järvinen
Move uart_change_speed() earlier to get rid of its forward declaration. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230309080923.11778-5-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-17serial: Use B0 instead of implicit zero assumptionIlpo Järvinen
Compare against B0 rather than assume B0 equals zero, which is true for all archs but explicit B0 makes the code more obvious. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230309080923.11778-3-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-17serial: Use ARRAY_SIZE() with iso7816 reserved arrayIlpo Järvinen
Instead of a literal, size the for loop iteration based on the actual array using ARRAY_SIZE(). Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230309080923.11778-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-16serial: sprd: Drop of_match_ptr for ID tableKrzysztof Kozlowski
The driver can match only via the DT table so the table should be always used and the of_match_ptr does not have any sense (this also allows ACPI matching via PRP0001, even though it is not relevant here). drivers/tty/serial/sprd_serial.c:1242:34: error: ‘serial_ids’ defined but not used [-Werror=unused-const-variable=] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com> Link: https://lore.kernel.org/r/20230310222957.315848-2-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-16serial: sh-sci: mark OF related data as maybe unusedKrzysztof Kozlowski
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/tty/serial/sh-sci.c:3144:34: error: ‘of_sci_match’ defined but not used [-Werror=unused-const-variable=] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230310222957.315848-1-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-16serial: Use of_property_read_bool() for boolean propertiesRob Herring
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. Convert reading boolean properties to to of_property_read_bool(). Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230310144727.1545699-1-robh@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-16serial: Use of_property_present() for testing DT property presenceRob Herring
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. As part of this, convert of_get_property/of_find_property calls to the recently added of_property_present() helper when we just want to test for presence of a property and nothing more. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230310144727.1545630-1-robh@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-09serial: sc16is7xx: Convert to i2c's .probe_new()Uwe Kleine-König
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/lkml/20221118224540.619276-572-uwe@kleine-koenig.org Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-03-09serial: qcom-geni: drop bogus uart_write_wakeup()Johan Hovold
Drop the bogus uart_write_wakeup() from when setting up a new DMA transfer, which does not free up any more space in the ring buffer. Any pending writers will be woken up when the transfer completes. Cc: stable <stable@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride Link: https://lore.kernel.org/r/20230307164405.14218-5-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-09serial: qcom-geni: fix mapping of empty DMA bufferJohan Hovold
Make sure that there is data in the ring buffer before trying to set up a zero-length DMA transfer. This specifically fixes the following warning when unmapping the empty buffer on the sc8280xp-crd: WARNING: CPU: 0 PID: 138 at drivers/iommu/dma-iommu.c:1046 iommu_dma_unmap_page+0xbc/0xd8 ... Call trace: iommu_dma_unmap_page+0xbc/0xd8 dma_unmap_page_attrs+0x30/0x1c8 geni_se_tx_dma_unprep+0x28/0x38 qcom_geni_serial_isr+0x358/0x75c Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA") Cc: stable <stable@kernel.org> Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride Link: https://lore.kernel.org/r/20230307164405.14218-4-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-09serial: qcom-geni: fix DMA mapping leak on shutdownJohan Hovold
Fix what appears to be a copy-paste error that can lead to a leaked DMA mapping on close() and failure to restart TX after the port is reopened. Note that rx_dma_addr is generally NULL when qcom_geni_serial_stop_tx_dma() is called as part of shutdown() (but tx_dma_addr need not be). Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA") Cc: stable <stable@kernel.org> Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride Link: https://lore.kernel.org/r/20230307164405.14218-3-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-09serial: qcom-geni: fix console shutdown hangJohan Hovold
A recent commit added back the calls top stop tx and rx to shutdown() which had previously been removed by commit e83766334f96 ("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART shutdown") in order to be able to use kgdb after stopping the getty. Not only did this again break kgdb, but it also broke serial consoles more generally by hanging TX when stopping the getty during reboot. The underlying problem has been there since the driver was first merged and fixing it is going to be a bit involved so simply stop calling the broken stop functions during shutdown for consoles for now. Fixes: d8aca2f96813 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown") Cc: stable <stable@kernel.org> Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride Link: https://lore.kernel.org/r/20230307164405.14218-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-09serial: 8250_em: Add serial8250_em_{reg_update(),out_helper()}Biju Das
As per RZ/V2M hardware manual(Rev.1.30 Jun, 2022), UART IP has a restriction as mentioned below. 40.6.1 Point for Caution when Changing the Register Settings: When changing the settings of the following registers, a PRESETn master reset or FIFO reset + SW reset (FCR[2],FCR[1], HCR0[7]) must be input to re-initialize them. Target Registers: FCR, LCR, MCR, DLL, DLM, HCR0. Add serial8250_em_reg_update() and serial8250_em_serial_out_helper() to handle this restriction. serial8250_em_serial_out_helper() is identical to previous serial8250_em_serial_out() except that UART_FCR macro is removed from serial8250_em_serial_out_helper() as it is now handled by serial8250_ em_serial_out(). DLL/DLM register can be updated only by setting LCR[7]. So the updation of LCR[7] will perform reset for DLL/DLM register changes. EMMA mobile has the same register set as RZ/V2M and this patch is tested on EMEV2 board. So, there is no harm in applying the same restriction here as well as the HW manual for EMMA mobile is not updated for a long time. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230227114152.22265-8-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-09serial: 8250_em: Use pseudo offset for UART_FCRBiju Das
UART_FCR shares the same offset with UART_IIR. We cannot use UART_FCR in serial8250_em_serial_in() as it overlaps with UART_IIR. Define UART_FCR_EM macro with a high value to avoid overlapping with existing UART_* register defines and define another macro UART_FCR_EM_HW for the real offset. Use these macros in serial8250_em_serial{_in/_out} function to read/write FCR register. Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230227114152.22265-7-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-09serial: 8250_em: Use devm_clk_get_enabled()Biju Das
Simplify clk handling in probe() by replacing devm_clk_get()->devm_ clk_get_enabled(). This replaces the usage of clk_prepare_enable/clk_ disable_unprepare() in probe()/remove(). After that sclk is no longer required in struct serial8250_em_priv and is replaced by a local variable sclk in probe(). Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230227114152.22265-6-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-09serial: 8250_em: Add missing break statementBiju Das
Add missing break statement in serial8250_em_serial_out(). Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230227114152.22265-5-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-09serial: 8250_em: Drop unused header fileBiju Das
Drop unused header file slab.h from the driver. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230227114152.22265-4-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit (git 2.34.1) at 2025-09-22 18:19:09 +0000