| Age | Commit message (Collapse) | Author |
|---|
|
serial_core might call the .start_tx callback without any data being
available to send. In this case return early instead of going through
all the setup needed for sending which might include disabling RX in
RS485 half-duplex mode.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using RS485 half duplex the Transmitter Complete irq is needed to
determine the moment when the transmitter can be disabled. When using
DMA this irq must only be enabled when DMA has completed to transfer all
data. Otherwise the CPU might busily trigger this irq which is not
properly handled and so the also pending irq for the DMA transfer cannot
trigger.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This allows to increase the RX waterlevel which allows to delay the RRDY
irq. The desired effect is that less irqs are needed to handle
characters and so reduce irq count of the system.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure that UCR1.RXDMAEN and UCR1.ATDMAEN (for the DMA case) and
UCR1.RRDYEN (for the PIO case) are off iff UCR1.RXEN is disabled. This
ensures that the fifo isn't read with RX disabled which results in an
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the UART is used in DMA mode, .stop_rx() does nothing if the port
isn't suspended. This is wrong as .stop_rx() should stop receiving
characters unconditionally. When the port is about to be closed the DMA
channel is stopped in .shutdown(), so this isn't necessary to be in
.stop_rx() here, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The aging timer fires if there are characters in the RX fifo but the
water level isn't reached yet. Make sure that the waterlevel is
configured before the aging timer is enabled to trigger a DMA request
(UCR1_ATDMAEN).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The serial/imx driver is full of inconsistently named and typed
variables that hold different register values.
Consistently use u32 as type (matching what readl and writel use) and
name the variables after the register whose value they are holding.
This makes it easier to notice when UCR2_RTSEN is written to UCR1.
The only difference introduced by this commit in the compiled driver is
that twice the second argument to warn_slowpath_null() changed because the
two WARN_ON in dma_rx_callback() pass __LINE__ to warn_slowpath_null().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The original code looks as follows:
if (sport->dma_is_enabled) {
... make sure TX DMA is running, i.e. .dma_is_txing = 1
}
if (sport->dma_is_txing)
return;
As .dma_is_txing can only be true if .dma_is_enabled is, the return can
go at the end of the first if body without an additional check.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Neither .dma_is_txing nor .dma_is_rxing can evaluate to true if
.dma_is_enabled evaluates to false:
The only function that sets .dma_is_txing to a non-zero value is
imx_dma_tx() which is only called if .dma_is_enabled is true. Same for
.dma_is_rxing and start_rx_dma(). And before .dma_is_enabled is set to 0
when imx_shutdown calls imx_disable_dma(), .dma_is_rxing and
.dma_is_txing are reset to zero before, too.
For this reason
sport->dma_is_enabled && sport->dma_is_rxing
has the same value as
sport->dma_is_rxing
which allows to simplify three if conditions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reduces the amount of read accesses to the register space by
shadowing the values for five registers that only change on writing
them. There is a single bit in UCR2 that might change without being
written to it, this is handled accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This prepares implementing shadow copies for the control registers and
additionally provides a good place to hook in debug code to trace
register usage.
Most of this patch was done using pattern substitution:
perl -p -i -e '
s/\breadl(?:_relaxed)?\((?:sport->port\.|port->)membase \+/imx_uart_readl(sport,/;
s/\bwritel(?:_relaxed)?\(([^,]*), (sport->port\.|port->)membase \+/imx_uart_writel(sport, $1,/;
' drivers/tty/serial/imx.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The RISC-V ISA defines a simple console that is availiable via SBI calls
on all systems. The SBI console is designed to be availiable at all
times, so while it's most natural to use this as an early printk target
it's also possible to use this as the system console when there isn't a
better one availiable.
This patch adds support for the RISC-V SBI console via the HVC
infastructure. It's entirely independent from our early printk support,
which results in early boot messages appearing twice over the SBI
console. As far as I can tell that's the fault of our early printk
support (we should support earlycon) as opposed to this driver.
There is one checkpatch.pl warning here: to check the MAINTAINERS file.
They're all matched by the "K: riscv" line.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that arch/metag/ has been removed, remove the metag DA TTY and
console driver. It is of no value without the architecture code.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-metag@vger.kernel.org
|
|
Consistently indicate being called with irqs off and the port lock taken
for all functions that this applies to.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Only the reference manual for the i.MX1 (I have MC9328MX1RM/D Rev 5 from
2004) uses TDMAEN and RDMAEN for these. All reference manuals for the
newer chips use TXDMAEN and RXDMAEN. Update to the newer name with the
assumption that most imx users don't use an imx1 any more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PCI ID database is for IDs used across several drivers.
Here is the case for SUNIX combo cards.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The cdns_uart_port[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 928e9263492069ee ("tty: xuartps: Initialize ports according to aliases")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sirf_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: a6ffe8966acbb66b ("serial: sirf: use dynamic method allocate uart structure")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sci_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SH_SCI_NR_UARTS), so this can even be triggered using a
legitimate DTB.
Fixes: 97ed9790c514066b ("serial: sh-sci: Remove unused platform data capabilities field")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The s3c24xx_serial_ports[] array is indexed using a value derived from
the "serialN" alias in DT, or from an incrementing probe index, which
may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SAMSUNG_UARTS), so this can even be triggered using
a legitimate DTB or legitimate board code.
Fixes: 13a9f6c64fdc55eb ("serial: samsung: Consider DT alias when probing ports")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The serial_pxa_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: 699c20f3e6310aa2 ("serial: pxa: add OF support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The auart_port[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: 1ea6607d4cdc9179 ("serial: mxs-auart: Allow device tree probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The imx_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: ff05967a07225ab6 ("serial/imx: add of_alias_get_id() reference back")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The lpuart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: c9e2e946fb0ba5d2 ("tty: serial: add Freescale lpuart driver support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The arc_uart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_ARC_NR_PORTS), so this can even be triggered using a
legitimate DTB.
Fixes: ea28fd56fcde69af ("serial/arc-uart: switch to devicetree based probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
imx_shutdown() calls imx_disable_dma if .dma_is_enabled. So after
imx_shudown() completes, .dma_is_enabled is zero. For this reason
.dma_is_enabled is also zero when imx_startup() is called. So the check
for this variable being zero can be dropped.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .dma_is_inited member is only set to a value != 0 when the port's
startup function calls imx_uart_dma_init(). On shutdown of the port
imx_uart_dma_exit is called which sets the value back to 0. So
.dma_is_inited is always 0 when imx_startup() is called (assuming
.startup() and .shutdown() are correctly balanced) and the check for
!sport->dma_is_inited can go away.
This allows to replace .dma_is_inited by a variable local to
imx_startup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Handling an irq that isn't enabled can have some undesired side effects.
Some of these are mentioned in the newly introduced code comment. Some
of the irq sources already had their handling right, some don't. Handle
them all in the same consistent way.
The change for USR1_RRDY and USR1_AGTIM drops the check for
dma_is_enabled. This is correct as UCR1_RRDYEN and UCR2_ATEN are always
off if dma is enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now the variable holding the value of register USR1 is called usr1
instead of sts which is more straight forward. The same is also done for
sts2 which is called usr2 now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The check sts & USR1_DTRD was just evaluated to true two lines above.
So this change doesn't have any effect on the semantic of the driver.
Fixes: 27e16501052e ("serial: imx: implement DSR irq handling for DTE mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Only one of the two is really required, not both:
* have_rtscts or
* have_rtsgpio
In imx_rs485_config() this is done correctly, so RS485 is working,
just the error message is false.
Signed-off-by: Phil Eichinger <phil@zankapfel.net>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: b8f3bff057b0 ("serial: imx: Support common rs485 binding for RTS polarity"
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the TTY buffers fill up to the configured maximum, a system lockup
occurs:
[ 598.820128] INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 598.825796] 0-...!: (1 GPs behind) idle=5a6/2/0 softirq=1974/1974 fqs=1
[ 598.832577] (detected by 3, t=62517 jiffies, g=296, c=295, q=126)
[ 598.838755] Task dump for CPU 0:
[ 598.841977] swapper/0 R running task 0 0 0 0x00000022
[ 598.849023] Call trace:
[ 598.851476] __switch_to+0x98/0xb0
[ 598.854870] (null)
This can be prevented by doing a dummy read of the RX data register.
This issue affects both HSCIF and SCIF ports. Reported for R-Car H3 ES2.0;
reproduced and fixed on H3 ES1.1. Probably affects other R-Car platforms
as well.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add PCI ids for two variants of Brainboxes UC-260 quad port
PCI serial cards.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It will get the wrong virtual address because port->mapbase is not added
the correct reg-offset yet. We have to update it before earlycon_map()
is called
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: stable@vger.kernel.org
Fixes: 088da2a17619 ("of: earlycon: Initialize port fields from DT properties")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a followup on 44117a1d1732 ("serial: core: mark port as
initialized after successful IRQ change").
Nikola has been using autoconfig via setserial and reported a crash
similar to what I fixed in the earlier mentioned commit. Here I do the
same fixup for the autoconfig. I wasn't sure that this is the right
approach. Nikola confirmed that it fixes his crash.
Fixes: b3b576461864 ("tty: serial_core: convert uart_open to use tty_port_open")
Link: http://lkml.kernel.org/r/20180131072000.GD1853@localhost.localdomain
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not fail on multiport cards in serial_pci_is_class_communication().
It restores behaviour for SUNIX multiport cards, that enumerated by
class and have a custom board data.
Moreover it allows users to reenumerate port-by-port from user space.
Fixes: 7d8905d06405 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On our at91sam9260 based board the usart0 and usart1 ports report
their versions (ATMEL_US_VERSION) as 0x10302. This version is not
included in the current checks in the driver.
Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Bit pattern STAT_FRM_ERR is being bit-wise or'd twice; remove the
redundant 2nd STAT_FRM_ERR
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This allows me to login after sending a break when service
serial-getty@ttymxc0.service is running
The "tty_insert_flip_char(port, 0, TTY_BREAK)" in clear_rx_errors
fixes this by allowing the higher layers to see a break.
Also, call uart_handle_break to handle possible
"secure attention key."
FYI: Martin said the ROM sdma firmware works with this patch,
but external sdma firmware still does not send breaks on a
i.mx6UL
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Martin Hicks <mort@bork.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
An issue has been observed on the Marvell Armada 38x serial port.
Writes to UART_LCR can result in characters that are currently held in the
TX FIFO being lost rather than sent, even if the userspace process has
attempted to flush them.
This is most visible when using the "resize" command (tested on Busybox),
where we have observed the escape code for restoring cursor position
becoming mangled.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
High latencies of classic timers cause performance issues for high-
speed serial transmissions. This patch transforms rx_timer into an
hrtimer to reduce the minimum latency.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
omap_8250_throttle() is called when tty RX buffer is about to overflow
and can no longer keep up with the rate at which UART is receiving data.
So, the expectation of this callback, is that UART stops RX and asserts
HW flow control to signal the sender to stop sending more data.
omap_8250_throttle() disables RX FIFO interrupts thus FIFO is no longer
serviced, leading to assertion of flow control once RX FIFO is full.
But, this does not work when DMA is enabled as driver keeps queuing new
RX DMA request in completion handler without brothering about throttling
request made by the higher layer.
This patch introduces a flag that can be used to determine whether or
not to queue next RX DMA request based on throttling request.
Without this patch, tty buffer overflows are reported at higher
baudrates.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, data in RX FIFO is read based on UART_LSR register state even
if RDI and RLSI interrupts are disabled in UART_IER register.
This is because when IRQ handler is called due to TX FIFO empty event,
RX FIFO is serviced based on UART_LSR register status instead of
UART_IIR status. This defeats the purpose of disabling UART RX
FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ
handler continues to drain UART RX FIFO resulting in overflow of buffer
at tty layer.
Fix this by making sure that driver drains UART RX FIFO only when
UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some debugging tools (/sys/kernel/debug/gpio, `lsgpio`) use the
gpio_chip's label for displaying an additional context. Right now, the
information duplicates stuff which is already available from the
parent's device. This is how e.g. `lsgpio`'s output looks like:
GPIO chip: gpiochip2, "spi1.2", 16 GPIO lines
Comparing the output of other GPIO expanders that I have available:
gpiochip4: GPIOs 464-479, parent: spi/spi1.1, mcp23s17, can sleep:
gpiochip5: GPIOs 448-463, parent: i2c/0-0020, pca9555, can sleep:
gpiochip2: GPIOs 496-511, parent: spi/spi1.2, spi1.2, can sleep:
This patch ensures that the type of the real HW device is shown instead
of duplicating the SPI path:
gpiochip2: GPIOs 496-511, parent: spi/spi1.2, MAX14830, can sleep:
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The UART can be operated without an irq. In this case a timer is setup
that regularily calls altera_uart_interrupt(). The receiving part
depends on pp->imr having the bit ALTERA_UART_STATUS_RRDY_MSK set,
otherwise altera_uart_rx_chars() is never called. So ensure that the bit
gets set (disguised as ALTERA_UART_CONTROL_RRDY_MSK) by not returning
early from altera_uart_startup() if port->irq is 0.
This doesn't affect the hardware as the ALTERA_UART_CONTROL_RRDY_MSK bit
isn't actually written to the control register.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the irq line of an altera UART device isn't used to report interrupts
for this device the driver better ensures that this device doesn't pull
this line to active state and so disturb the whatever might be connected
to this line.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most register accesses in the altera driver honor port->regshift by
using altera_uart_writel(). There are a few accesses however that were
missed when the driver was converted to use port->regshift and some
others were added later in commit 4d9d7d896d77 ("serial: altera_uart:
add earlycon support").
Fixes: 2780ad42f5fe ("tty: serial: altera_uart: Use port->regshift to store bus shift")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A tty is hung up by __tty_hangup() setting file->f_op to
hung_up_tty_fops, which is skipped on ttys whose write operation isn't
tty_write(). This means that, for example, /dev/console whose write
op is redirected_tty_write() is never actually marked hung up.
Because n_tty_read() uses the hung up status to decide whether to
abort the waiting readers, the lack of hung-up marking can lead to the
following scenario.
1. A session contains two processes. The leader and its child. The
child ignores SIGHUP.
2. The leader exits and starts disassociating from the controlling
terminal (/dev/console).
3. __tty_hangup() skips setting f_op to hung_up_tty_fops.
4. SIGHUP is delivered and ignored.
5. tty_ldisc_hangup() is invoked. It wakes up the waits which should
clear the read lockers of tty->ldisc_sem.
6. The reader wakes up but because tty_hung_up_p() is false, it
doesn't abort and goes back to sleep while read-holding
tty->ldisc_sem.
7. The leader progresses to tty_ldisc_lock() in tty_ldisc_hangup()
and is now stuck in D sleep indefinitely waiting for
tty->ldisc_sem.
The following is Alan's explanation on why some ttys aren't hung up.
http://lkml.kernel.org/r/20171101170908.6ad08580@alans-desktop
1. It broke the serial consoles because they would hang up and close
down the hardware. With tty_port that *should* be fixable properly
for any cases remaining.
2. The console layer was (and still is) completely broken and doens't
refcount properly. So if you turn on console hangups it breaks (as
indeed does freeing consoles and half a dozen other things).
As neither can be fixed quickly, this patch works around the problem
by introducing a new flag, TTY_HUPPING, which is used solely to tell
n_tty_read() that hang-up is in progress for the console and the
readers should be aborted regardless of the hung-up status of the
device.
The following is a sample hung task warning caused by this issue.
INFO: task agetty:2662 blocked for more than 120 seconds.
Not tainted 4.11.3-dbg-tty-lockup-02478-gfd6c7ee-dirty #28
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
0 2662 1 0x00000086
Call Trace:
__schedule+0x267/0x890
schedule+0x36/0x80
schedule_timeout+0x23c/0x2e0
ldsem_down_write+0xce/0x1f6
tty_ldisc_lock+0x16/0x30
tty_ldisc_hangup+0xb3/0x1b0
__tty_hangup+0x300/0x410
disassociate_ctty+0x6c/0x290
do_exit+0x7ef/0xb00
do_group_exit+0x3f/0xa0
get_signal+0x1b3/0x5d0
do_signal+0x28/0x660
exit_to_usermode_loop+0x46/0x86
do_syscall_64+0x9c/0xb0
entry_SYSCALL64_slow_path+0x25/0x25
The following is the repro. Run "$PROG /dev/console". The parent
process hangs in D state.
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/wait.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <unistd.h>
#include <stdio.h>
#include <stdlib.h>
#include <errno.h>
#include <signal.h>
#include <time.h>
#include <termios.h>
int main(int argc, char **argv)
{
struct sigaction sact = { .sa_handler = SIG_IGN };
struct timespec ts1s = { .tv_sec = 1 };
pid_t pid;
int fd;
if (argc < 2) {
fprintf(stderr, "test-hung-tty /dev/$TTY\n");
return 1;
}
/* fork a child to ensure that it isn't already the session leader */
pid = fork();
if (pid < 0) {
perror("fork");
return 1;
}
if (pid > 0) {
/* top parent, wait for everyone */
while (waitpid(-1, NULL, 0) >= 0)
;
if (errno != ECHILD)
perror("waitpid");
return 0;
}
/* new session, start a new session and set the controlling tty */
if (setsid() < 0) {
perror("setsid");
return 1;
}
fd = open(argv[1], O_RDWR);
if (fd < 0) {
perror("open");
return 1;
}
if (ioctl(fd, TIOCSCTTY, 1) < 0) {
perror("ioctl");
return 1;
}
/* fork a child, sleep a bit and exit */
pid = fork();
if (pid < 0) {
perror("fork");
return 1;
}
if (pid > 0) {
nanosleep(&ts1s, NULL);
printf("Session leader exiting\n");
exit(0);
}
/*
* The child ignores SIGHUP and keeps reading from the controlling
* tty. Because SIGHUP is ignored, the child doesn't get killed on
* parent exit and the bug in n_tty makes the read(2) block the
* parent's control terminal hangup attempt. The parent ends up in
* D sleep until the child is explicitly killed.
*/
sigaction(SIGHUP, &sact, NULL);
printf("Child reading tty\n");
while (1) {
char buf[1024];
if (read(fd, buf, sizeof(buf)) < 0) {
perror("read");
return 1;
}
}
return 0;
}
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups, a few new quirks, a couple of
updates related to the handling of ACPI tables and ACPICA copyrights
refreshment.
Specifics:
- Update the ACPICA kernel code to upstream revision 20180105
including:
* Assorted fixes (Jung-uk Kim)
* Support for X32 ABI compilation (Anuj Mittal)
* Update of ACPICA copyrights to 2018 (Bob Moore)
- Prepare for future modifications to avoid executing the _STA
control method too early (Hans de Goede)
- Make the processor performance control library code ignore _PPC
notifications if they cannot be handled and fix up the C1 idle
state definition when it is used as a fallback state (Chen Yu,
Yazen Ghannam)
- Make it possible to use the SPCR table on x86 and to replace the
original IORT table with a new one from initrd (Prarit Bhargava,
Shunyong Yang)
- Add battery-related quirks for Asus UX360UA and UX410UAK and add
quirks for table parsing on Dell XPS 9570 and Precision M5530 (Kai
Heng Feng)
- Address static checker warnings in the CPPC code (Gustavo Silva)
- Avoid printing a raw pointer to the kernel log in the smart battery
driver (Greg Kroah-Hartman)"
* tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: sbshc: remove raw pointer from printk() message
ACPI: SPCR: Make SPCR available to x86
ACPI / CPPC: Use 64-bit arithmetic instead of 32-bit
ACPI / tables: Add IORT to injectable table list
ACPI / bus: Parse tables as term_list for Dell XPS 9570 and Precision M5530
ACPICA: Update version to 20180105
ACPICA: All acpica: Update copyrights to 2018
ACPI / processor: Set default C1 idle state description
ACPI / battery: Add quirk for Asus UX360UA and UX410UAK
ACPI: processor_perflib: Do not send _PPC change notification if not ready
ACPI / scan: Use acpi_bus_get_status() to initialize ACPI_TYPE_DEVICE devs
ACPI / bus: Do not call _STA on battery devices with unmet dependencies
PCI: acpiphp_ibm: prepare for acpi_get_object_info() no longer returning status
ACPI: export acpi_bus_get_status_handle()
ACPICA: Add a missing pair of parentheses
ACPICA: Prefer ACPI_TO_POINTER() over ACPI_ADD_PTR()
ACPICA: Avoid NULL pointer arithmetic
ACPICA: Linux: add support for X32 ABI compilation
ACPI / video: Use true for boolean value
|
