| Age | Commit message (Collapse) | Author |
|---|
|
This patch remove the extra compatibility string "st,stm32-usart" from
driver & device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The atmel serial port driver reported the following warning on suspend:
atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter
As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
when the transmitter is disabled, we need to know the transmitter's
state to return the real fifo state. And as ATMEL_US_CR is write-only,
it is necessary to save the state of the transmitter in a local
variable, and update the variable when TXEN and TXDIS is written in
ATMEL_US_CR.
After those changes, atmel_tx_empty can return "empty" on suspend, the
warning in uart_suspend_port disappears, and suspending is 20ms shorter
for each enabled Atmel serial port.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
HSCIF has facilities that allow changing the timeout after which an RX
interrupt is triggered even if the FIFO is not filled. This patch allows
changing the default (15 bits of silence) using the existing sysfs
attribute "rx_fifo_timeout".
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes the checkpatch.pl error complain:
ERROR: space required before the open brace '{'
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch is fix the warning reported by smatch as following:
drivers/tty/serial/8250/8250_fintek.c:294 fintek_8250_goto_highspeed()
warn: inconsistent indenting
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The F81216H had 4 clocksource 1.8432/18.432/14.769/24MHzand baud rates can
be up to 1.5Mbits with 24MHz. The register value and mask is the same with
F81866. But F81866 register address is F2h, F81216H is F0h.
We'll implements the dynamic clocksource in fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The F81866 had 4 clocksource 1.8432/18.432/14.769/24MHz and baud rates can
be up to 1.5Mbits with 24MHz. We'll implements the dynamic clocksource in
fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable "dma_is_txing" is an unsigned int, set as either "0" or "1"
in all but one location, where it is instead set to "false". For
consistency, set dma_is_txing to "0" in this location too.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The imx serial driver uses PAGE_SIZE when allocating rx_buf, but then
uses RX_BUF_SIZE (which is currently defined as PAGE_SIZE) to describe
the length of the buffer when initialising the scatter gather list.
In order to ensure that this stays consistent, use RX_BUF_SIZE in both
locations.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-könig@pengtronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable dma_is_rxing is currently set to 1 in imx_disable_rx_int().
This is problematic as:
- whilst imx_disable_rx_int() is currently always called before
start_rx_dma() this dependency isn't obvious.
- start_rx_dma() does error checking and might exit without
enabling DMA. Currently this will result in dma_is_rxing suggesting
that DMA is being used for recieving.
To avoid these issues, move the setting of dma_is_rxing to
start_rx_dma() when appropriate.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UART core function uart_update_mctrl relies on a cached value of
modem control lines. This was used but not updated by local RTS
control functions within imx.c. These are used for RS485 line
driver enable signalling. Having an out-of-date value in the cached
mctrl can result in the transmitter being enabled when it shouldn't
be.
Fix this by updating the mctrl value before applying it.
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Origin: id:8195c96e674517b82a6ff7fe914c7ba0f86e702b.1505375165.git.ian.dev@arkver.com
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds support for the rs485 specific properties defined in
Documentation/devicetree/bindings/serial/rs485.txt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Forwarded: id:20170913081833.2740-7-u.kleine-koenig@pengutronix.de (v5)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The i.MX driver defaulted to full duplex rs485 which is rather
unusual and doesn't match the default implemented in other drivers.
So change the default to half duplex.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
As a side effect this adds support for parsing rs485-rts-delay and
rs485-rx-during-tx. As the driver doesn't support this though, probing
fails if these are defined.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
Note that there is a small difference between the removed and the now
used implementation: The former cleared flags to 0 if rs485-rts-delay
was given, the common helper clears SER_RS485_RX_DURING_TX and
SER_RS485_ENABLED only but always which makes more sense.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[ukleinek: point out semantic change in commit log]
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Several drivers have the same device tree parsing code. Create
a common helper function for it.
This patch bases on work done by Sascha Hauer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit a6d7514b14a6 ("tty: serial: lpuart: add a more accurate baud
rate calculation method") the baud rate is now calculated inside the
lpuart32_serial_setbrg() function, so we no longer need to read the
UARTBAUD register inside lpuart32_set_termios().
The 'bd' variable can be simply removed.
This fixes the following build warning with W=1:
drivers/tty/serial/fsl_lpuart.c: In function 'lpuart32_set_termios':
drivers/tty/serial/fsl_lpuart.c:1652:32: warning: variable 'bd' set but not used [-Wunused-but-set-variable]
Fixes: a6d7514b14a6 ("tty: serial: lpuart: add a more accurate baud rate calculation method")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to avoid code duplication and to be more consistent with the
other error handling paths in this function, we should 'goto errout'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use bsearch library function instead of duplicated functionality.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make this const as it is only stored in the const field 'ops' of an
uart_port structure. It is not referenced in any other file and therefore
make it static too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix some minor typo spotted in comments:
- s/wit ha/with a/
- s/doestroyed/destroyed/
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This dirver try to implement the Magic SysRq support[1] for
Amlogic Inc's meson platfo
>From the hardware perspective, the UART IP can't detect the 'BREAK' command
clearly via the status register. Instead, we rely on the combination of
'FRAME_ERR bit && ch == 0', and it works fine.
[1] Documentation/admin-guide/sysrq.rst
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sccnxp_probe() returns result of regulator_disable() that may lead
to returning zero, while device is not properly initialized.
Also the driver enables clocks, but it does not disable it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current driver register irq in .startup() and free the irq in
.shutdown(), then user will see the NULL interrupt output from
'cat /proc/interrupts' after the uart port test completed:
...
41: 515 0 0 0 GICv3 257 Level fsl-lpuart
42: 2 0 0 0 GICv3 258 Level
...
It is better to register all the irqs during probe function via devm_request_irq()
to avoid to call free_irq().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Issue where unprintable characters can occur or output is cut off over
the serial uart / linux console depending on timing.
Problem occurs when changing the serial baud rate when setting up the
new console.The bcm63xx driver does a disable and flush of the uart tx
fifo while there is data still in the tx fifo.
If the tx fifo still has data it is trying to send out, we need to wait
until it is empty before disabling and flushing the uart.
When we now go to change the uart parameters including speed we check
if there is data currently in the tx fifo.If there is was mdelay(10)
and check again.If it tries 3 times and still has data in it we just
continue and sacrifice the tx fifo buffer.
A cleaner and more preferred approach would be to remove :
- spin_lock_irqsave()
- bcm_uart_disable()
- bcm_uart_flush()
However it is not clear if the author put those in to fix another
underlying issue.As a result this solution is a safer approach.
Output before the fix:
[0.306000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud = 1687500) is a° 0.315000] console[ttyS0] enabled
Output verified after the fix:
[0.315000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud = 1687500) is a bcm63xx_uart [0.334000] console[ttyS0] enabled
Signed-off-by: Russell Enderby <rte@gdn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Paul reported, that low rates like B300 make the driver to hang in
mxser_wait_until_sent. His debugging tackled the issue down to the
info->timeout computation in mxser_set_baud. Obviously, ints are used
there and they easily overflow with these low rates: B300 makes
info->timeout to be -373.
So switch all these types to unsigned as it ought to be. And use the u64
domain to perform the computation as in the worst case, we need 35 bits
to store the computed value (before division).
And use do_div not to break 32 bit kernels.
[v2] make it actually build
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Paul <Paul@abelian.netcom.co.uk>
Tested-by: <Paul@abelian.netcom.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
Pull sparc updates from David Miller:
1) Use register window state adjustment instructions when available,
from Anthony Yznaga.
2) Add VCC console concentrator driver, from Jag Raman.
3) Add 16GB hugepage support, from Nitin Gupta.
4) Support cpu 'poke' hypercall, from Vijay Kumar.
5) Add M7/M8 optimized memcpy/memset/copy_{to,from}_user, from Babu
Moger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next: (33 commits)
sparc64: Handle additional cases of no fault loads
sparc64: speed up etrap/rtrap on NG2 and later processors
sparc64: vcc: make ktermios const
sparc: leon: grpci1: constify of_device_id
sparc: leon: grpci2: constify of_device_id
sparc64: vcc: Check for IS_ERR() instead of NULL
sparc64: Cleanup hugepage table walk functions
sparc64: Add 16GB hugepage support
sparc64: Support huge PUD case in get_user_pages
sparc64: vcc: Add install & cleanup TTY operations
sparc64: vcc: Add break_ctl TTY operation
sparc64: vcc: Add chars_in_buffer TTY operation
sparc64: vcc: Add write & write_room TTY operations
sparc64: vcc: Add hangup TTY operation
sparc64: vcc: Add open & close TTY operations
sparc64: vcc: Enable LDC event processing engine
sparc64: vcc: Add RX & TX timer for delayed LDC operation
sparc64: vcc: Create sysfs attribute group
sparc64: vcc: Enable VCC port probe and removal
sparc64: vcc: TTY driver initialization and cleanup
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Nothing really major this release, despite quite a lot of activity.
Just lots of things all over the place.
Some things of note include:
- Access via perf to a new type of PMU (IMC) on Power9, which can
count both core events as well as nest unit events (Memory
controller etc).
- Optimisations to the radix MMU TLB flushing, mostly to avoid
unnecessary Page Walk Cache (PWC) flushes when the structure of the
tree is not changing.
- Reworks/cleanups of do_page_fault() to modernise it and bring it
closer to other architectures where possible.
- Rework of our page table walking so that THP updates only need to
send IPIs to CPUs where the affected mm has run, rather than all
CPUs.
- The size of our vmalloc area is increased to 56T on 64-bit hash MMU
systems. This avoids problems with the percpu allocator on systems
with very sparse NUMA layouts.
- STRICT_KERNEL_RWX support on PPC32.
- A new sched domain topology for Power9, to capture the fact that
pairs of cores may share an L2 cache.
- Power9 support for VAS, which is a new mechanism for accessing
coprocessors, and initial support for using it with the NX
compression accelerator.
- Major work on the instruction emulation support, adding support for
many new instructions, and reworking it so it can be used to
implement the emulation needed to fixup alignment faults.
- Support for guests under PowerVM to use the Power9 XIVE interrupt
controller.
And probably that many things again that are almost as interesting,
but I had to keep the list short. Plus the usual fixes and cleanups as
always.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Andreas Schwab,
Aneesh Kumar K.V, Anju T Sudhakar, Arvind Yadav, Balbir Singh,
Benjamin Herrenschmidt, Bhumika Goyal, Breno Leitao, Bryant G. Ly,
Christophe Leroy, Cédric Le Goater, Dan Carpenter, Dou Liyang,
Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff Levand, Hannes
Reinecke, Haren Myneni, Ivan Mikhaylov, John Allen, Julia Lawall,
LABBE Corentin, Laurentiu Tudor, Madhavan Srinivasan, Markus Elfring,
Masahiro Yamada, Matt Brown, Michael Neuling, Murilo Opsfelder Araujo,
Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran,
Paul Mackerras, Rashmica Gupta, Rob Herring, Rui Teng, Sam Bobroff,
Santosh Sivaraj, Scott Wood, Shilpasri G Bhat, Sukadev Bhattiprolu,
Suraj Jitindar Singh, Tobin C. Harding, Victor Aoqui"
* tag 'powerpc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (321 commits)
powerpc/xive: Fix section __init warning
powerpc: Fix kernel crash in emulation of vector loads and stores
powerpc/xive: improve debugging macros
powerpc/xive: add XIVE Exploitation Mode to CAS
powerpc/xive: introduce H_INT_ESB hcall
powerpc/xive: add the HW IRQ number under xive_irq_data
powerpc/xive: introduce xive_esb_write()
powerpc/xive: rename xive_poke_esb() in xive_esb_read()
powerpc/xive: guest exploitation of the XIVE interrupt controller
powerpc/xive: introduce a common routine xive_queue_page_alloc()
powerpc/sstep: Avoid used uninitialized error
axonram: Return directly after a failed kzalloc() in axon_ram_probe()
axonram: Improve a size determination in axon_ram_probe()
axonram: Delete an error message for a failed memory allocation in axon_ram_probe()
powerpc/powernv/npu: Move tlb flush before launching ATSD
powerpc/macintosh: constify wf_sensor_ops structures
powerpc/iommu: Use permission-specific DEVICE_ATTR variants
powerpc/eeh: Delete an error out of memory message at init time
powerpc/mm: Use seq_putc() in two functions
macintosh: Convert to using %pOF instead of full_name
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver update for 4.14-rc1.
Lots of staging driver fixes and cleanups, including some reorginizing
of the lustre header files to try to impose some sanity on what is,
and what is not, the uapi for that filesystem.
There are some tty core changes in here as well, as the speakup
drivers need them, and that's ok with me, they are sane and the
speakup code is getting nicer because of it.
There is also the addition of the obiligatory new wifi driver, just
because it has been a release or two since we added our last one...
Other than that, lots and lots of small coding style fixes, as usual.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (612 commits)
staging:rtl8188eu:core Fix remove unneccessary else block
staging: typec: fusb302: make structure fusb302_psy_desc static
staging: unisys: visorbus: make two functions static
staging: fsl-dpaa2/eth: fix off-by-one FD ctrl bitmaks
staging: r8822be: Simplify deinit_priv()
staging: r8822be: Remove some dead code
staging: vboxvideo: Use CONFIG_DRM_KMS_FB_HELPER to check for fbdefio availability
staging:rtl8188eu Fix comparison to NULL
staging: rts5208: rename mmc_ddr_tunning_rx_cmd to mmc_ddr_tuning_rx_cmd
Staging: Pi433: style fix - tabs and spaces
staging: pi433: fix spelling mistake: "preample" -> "preamble"
staging:rtl8188eu:core Fix Code Indent
staging: typec: fusb302: Export current-limit through a power_supply class dev
staging: typec: fusb302: Add support for USB2 charger detection through extcon
staging: typec: fusb302: Use client->irq as irq if set
staging: typec: fusb302: Get max snk mv/ma/mw from device-properties
staging: typec: fusb302: Set max supply voltage to 5V
staging: typec: tcpm: Add get_current_limit tcpc_dev callback
staging:rtl8188eu Use __func__ instead of function name
staging: lustre: coding style fixes found by checkpatch.pl
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver update for 4.14-rc1.
Well, not all that big, just a number of small serial driver fixes,
and a new serial driver. Also in here are some much needed goldfish
tty driver (emulator) fixes to try to get that codebase under control.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (94 commits)
tty: goldfish: Implement support for kernel 'earlycon' parameter
tty: goldfish: Use streaming DMA for r/w operations on Ranchu platforms
tty: goldfish: Refactor constants to better reflect their nature
serial: 8250_port: Remove useless NULL checks
earlycon: initialise baud field of earlycon device structure
tty: hvcs: make ktermios const
pty: show associative slave of ptmx in fdinfo
tty: n_gsm: Add compat_ioctl
tty: hvcs: constify vio_device_id
tty: hvc_vio: constify vio_device_id
tty: mips_ejtag_fdc: constify mips_cdmm_device_id
Introduce 8250_men_mcb
mcb: introduce mcb_get_resource()
serial: imx: Avoid post-PIO cleanup if TX DMA is started
tty: serial: imx: disable irq after suspend
serial: 8250_uniphier: add suspend/resume support
serial: 8250_uniphier: use CHAR register for canary to detect power-off
serial: 8250_uniphier: fix serial port index in private data
serial: 8250: of: Add new port type for MediaTek BTIF controller on MT7622/23 SoC
dt-bindings: serial: 8250: Add MediaTek BTIF controller bindings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Major changes include:
- Full support of the firmware Page Deallocation Table with
MADV_HWPOISON and MADV_SOFT_OFFLINE. A kernel thread scans
regularily for new bad memory pages.
- Full support for self-extracting kernel.
- Added UBSAN support.
- Lots of section mismatch fixes across all parisc drivers.
- Added examples for %pF and %pS usage in printk-formats.txt"
* 'parisc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (28 commits)
printk-formats.txt: Add examples for %pF and %pS usage
parisc: Fix up devices below a PCI-PCI MegaRAID controller bridge
parisc/core: Fix section mismatches
parisc/ipmi_si_intf: Fix section mismatches on parisc platform
parisc/input/hilkbd: Fix section mismatches
parisc/net/lasi_82596: Fix section mismatches
parisc/serio: Fix section mismatches in gscps2 and hp_sdc drivers
parisc: Fix section mismatches in parisc core drivers
parisc/parport_gsc: Fix section mismatches
parisc/scsi/lasi700: Fix section mismatches
parisc/scsi/zalon: Fix section mismatches
parisc/8250_gsc: Fix section mismatches
parisc/mux: Fix section mismatches
parisc/sticore: Fix section mismatches
parisc/harmony: Fix section mismatches
parisc: Wire up support for self-extracting kernel
parisc: Make existing core files reuseable for bootloader
parisc: Add core code for self-extracting kernel
parisc: Enable UBSAN support
parisc/random: Add machine specific randomness
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 asm updates from Ingo Molnar:
- Introduce the ORC unwinder, which can be enabled via
CONFIG_ORC_UNWINDER=y.
The ORC unwinder is a lightweight, Linux kernel specific debuginfo
implementation, which aims to be DWARF done right for unwinding.
Objtool is used to generate the ORC unwinder tables during build, so
the data format is flexible and kernel internal: there's no
dependency on debuginfo created by an external toolchain.
The ORC unwinder is almost two orders of magnitude faster than the
(out of tree) DWARF unwinder - which is important for perf call graph
profiling. It is also significantly simpler and is coded defensively:
there has not been a single ORC related kernel crash so far, even
with early versions. (knock on wood!)
But the main advantage is that enabling the ORC unwinder allows
CONFIG_FRAME_POINTERS to be turned off - which speeds up the kernel
measurably:
With frame pointers disabled, GCC does not have to add frame pointer
instrumentation code to every function in the kernel. The kernel's
.text size decreases by about 3.2%, resulting in better cache
utilization and fewer instructions executed, resulting in a broad
kernel-wide speedup. Average speedup of system calls should be
roughly in the 1-3% range - measurements by Mel Gorman [1] have shown
a speedup of 5-10% for some function execution intense workloads.
The main cost of the unwinder is that the unwinder data has to be
stored in RAM: the memory cost is 2-4MB of RAM, depending on kernel
config - which is a modest cost on modern x86 systems.
Given how young the ORC unwinder code is it's not enabled by default
- but given the performance advantages the plan is to eventually make
it the default unwinder on x86.
See Documentation/x86/orc-unwinder.txt for more details.
- Remove lguest support: its intended role was that of a temporary
proof of concept for virtualization, plus its removal will enable the
reduction (removal) of the paravirt API as well, so Rusty agreed to
its removal. (Juergen Gross)
- Clean up and fix FSGS related functionality (Andy Lutomirski)
- Clean up IO access APIs (Andy Shevchenko)
- Enhance the symbol namespace (Jiri Slaby)
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (47 commits)
objtool: Handle GCC stack pointer adjustment bug
x86/entry/64: Use ENTRY() instead of ALIGN+GLOBAL for stub32_clone()
x86/fpu/math-emu: Add ENDPROC to functions
x86/boot/64: Extract efi_pe_entry() from startup_64()
x86/boot/32: Extract efi_pe_entry() from startup_32()
x86/lguest: Remove lguest support
x86/paravirt/xen: Remove xen_patch()
objtool: Fix objtool fallthrough detection with function padding
x86/xen/64: Fix the reported SS and CS in SYSCALL
objtool: Track DRAP separately from callee-saved registers
objtool: Fix validate_branch() return codes
x86: Clarify/fix no-op barriers for text_poke_bp()
x86/switch_to/64: Rewrite FS/GS switching yet again to fix AMD CPUs
selftests/x86/fsgsbase: Test selectors 1, 2, and 3
x86/fsgsbase/64: Report FSBASE and GSBASE correctly in core dumps
x86/fsgsbase/64: Fully initialize FS and GS state in start_thread_common
x86/asm: Fix UNWIND_HINT_REGS macro for older binutils
x86/asm/32: Fix regs_get_register() on segment registers
x86/xen/64: Rearrange the SYSCALL entries
x86/asm/32: Remove a bunch of '& 0xffff' from pt_regs segment reads
...
|
|
Add early console functionality to the Goldfish tty driver.
When 'earlycon' kernel command line parameter is used with no options,
the early console is determined by the 'stdout-path' property in device
tree's 'chosen' node. This is illustrated in the following device tree
source example:
Device tree example:
chosen {
stdout-path = "/goldfish_tty@1f004000";
};
goldfish_tty@1f004000 {
interrupts = <0xc>;
reg = <0x1f004000 0x0 0x1000>;
compatible = "google,goldfish-tty";
};
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement tty r/w operations using streaming DMA.
Goldfish tty for Ranchu platforms has been modified to use
streaming DMA mappings for read/write operations. This change
eliminates the need for snooping through the TLB in QEMU using
cpu_get_phys_page_debug() which does not guarantee that it will
return the valid va -> pa mapping.
The streaming DMA mapping is implemented using dma_map_single() per
transfer, while dma_unmap_single() is used for unmapping right after
the DMA transfer.
Using DMA API is the proper way for handling r/w transfers and
makes this driver more portable, thus effectively eliminating
the need for virt_to_page() and page_to_phys() conversions.
This change does not affect the old style Goldfish tty behaviour
which is still used by the Goldfish emulator. Version register has
been added and probed to see which platform is running this driver.
Reading from the new register GOLDFISH_TTY_REG_VERSION using the
Goldfish emulator will return 0 and driver will work with virtual
addresses. Whereas if run on Ranchu it returns 1, and thus DMA is
used.
(Goldfish and Ranchu are code names for the first and the second
generation of virtual boards used by Android emulator.)
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Classify constants GOLDFISH_TTY_xxx into two groups: command ids and
register offsets. Apply different naming for register offsets (add
'REG_' after 'GOLDFISH_TTY_' in constant names). Change implementation
to use preprocessor's '#define' statements instead of 'enum'
declaration (as this is more common way of implementation in such
cases).
This makes the driver code easier to follow and hopefully prevents
future bugs.
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After switching to HR timers for RS485 the NULL checks for the object
inside timer functions become useless.
Remove them to avoid confusion to static analyzers.
Fixes 6e0a5de2136b ("serial: 8250: Use hrtimers for rs485 delays")
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
