| Age | Commit message (Collapse) | Author |
|---|
|
It is possible that typec_register_partner() returns ERR_PTR on failure.
When port->partner is an error, a NULL pointer dereference may occur as
shown below.
[91222.095236][ T319] typec port0: failed to register partner (-17)
...
[91225.061491][ T319] Unable to handle kernel NULL pointer dereference
at virtual address 000000000000039f
[91225.274642][ T319] pc : tcpm_pd_data_request+0x310/0x13fc
[91225.274646][ T319] lr : tcpm_pd_data_request+0x298/0x13fc
[91225.308067][ T319] Call trace:
[91225.308070][ T319] tcpm_pd_data_request+0x310/0x13fc
[91225.308073][ T319] tcpm_pd_rx_handler+0x100/0x9e8
[91225.355900][ T319] kthread_worker_fn+0x178/0x58c
[91225.355902][ T319] kthread+0x150/0x200
[91225.355905][ T319] ret_from_fork+0x10/0x30
Add a check for port->partner to avoid dereferencing a NULL pointer.
Fixes: 5e1d4c49fbc8 ("usb: typec: tcpm: Determine common SVDM Version")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Link: https://lore.kernel.org/r/20231020012132.100960-1-hhhuuu@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb: typec: altmodes/displayport: Signal hpd low when exiting mode
and
drm: Add HPD state to drm_connector_oob_hotplug_event()
sideswiped each other.
Signal disconnected always.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is needed to add the msm pr which is based on a higher base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Previously, gadget assignment to the net device occurred exclusively
during the initial binding attempt.
Nevertheless, the gadget pointer could change during bind/unbind
cycles due to various conditions, including the unloading/loading
of the UDC device driver or the detachment/reconnection of an
OTG-capable USB hub device.
This patch relocates the gether_set_gadget() function out from
ncm_opts->bound condition check, ensuring that the correct gadget
is assigned during each bind request.
The provided logs demonstrate the consistency of ncm_opts throughout
the power cycle, while the gadget may change.
* OTG hub connected during boot up and assignment of gadget and
ncm_opts pointer
[ 2.366301] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105
[ 2.366304] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.366306] usb 2-1.5: Product: H2H Bridge
[ 2.366308] usb 2-1.5: Manufacturer: Aptiv
[ 2.366309] usb 2-1.5: SerialNumber: 13FEB2021
[ 2.427989] usb 2-1.5: New USB device found, VID=2996, PID=0105
[ 2.428959] dabridge 2-1.5:1.0: dabridge 2-4 total endpoints=5, 0000000093a8d681
[ 2.429710] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[ 2.429714] dabridge 2-1.5:1.0: Hub 2-2 P(0151) V(06.87)
[ 2.429956] dabridge 2-1.5:1.0: All downstream ports in host mode
[ 2.430093] gadget 000000003c414d59 ------> gadget pointer
* NCM opts and associated gadget pointer during First ncm_bind
[ 34.763929] NCM opts 00000000aa304ac9
[ 34.763930] NCM gadget 000000003c414d59
* OTG capable hub disconnecte or assume driver unload.
[ 97.203114] usb 2-1: USB disconnect, device number 2
[ 97.203118] usb 2-1.1: USB disconnect, device number 3
[ 97.209217] usb 2-1.5: USB disconnect, device number 4
[ 97.230990] dabr_udc deleted
* Reconnect the OTG hub or load driver assaign new gadget pointer.
[ 111.534035] usb 2-1.1: New USB device found, idVendor=2996, idProduct=0120, bcdDevice= 6.87
[ 111.534038] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 111.534040] usb 2-1.1: Product: Vendor
[ 111.534041] usb 2-1.1: Manufacturer: Aptiv
[ 111.534042] usb 2-1.1: SerialNumber: Superior
[ 111.535175] usb 2-1.1: New USB device found, VID=2996, PID=0120
[ 111.610995] usb 2-1.5: new high-speed USB device number 8 using xhci-hcd
[ 111.630052] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105, bcdDevice=21.02
[ 111.630055] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 111.630057] usb 2-1.5: Product: H2H Bridge
[ 111.630058] usb 2-1.5: Manufacturer: Aptiv
[ 111.630059] usb 2-1.5: SerialNumber: 13FEB2021
[ 111.687464] usb 2-1.5: New USB device found, VID=2996, PID=0105
[ 111.690375] dabridge 2-1.5:1.0: dabridge 2-8 total endpoints=5, 000000000d87c961
[ 111.691172] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[ 111.691176] dabridge 2-1.5:1.0: Hub 2-6 P(0151) V(06.87)
[ 111.691646] dabridge 2-1.5:1.0: All downstream ports in host mode
[ 111.692298] gadget 00000000dc72f7a9 --------> new gadget ptr on connect
* NCM opts and associated gadget pointer during second ncm_bind
[ 113.271786] NCM opts 00000000aa304ac9 -----> same opts ptr used during first bind
[ 113.271788] NCM gadget 00000000dc72f7a9 ----> however new gaget ptr, that will not set
in net_device due to ncm_opts->bound = true
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20231020153324.82794-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Simplify the code by not calling hub_is_superspeed() twice.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/b1d77cbc-faa3-4d07-94ff-f6ffb85c6964@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When transitioning from SNK_DEBOUNCED to unattached, its worthwhile to
check for contaminant to mitigate wakeups.
```
[81334.219571] Start toggling
[81334.228220] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[81334.305147] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[81334.305162] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[81334.305187] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[81334.475515] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[81334.486480] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_DEBOUNCED, polarity 0, disconnected]
[81334.486495] state change SNK_DEBOUNCED -> SNK_DEBOUNCED [rev3 NONE_AMS]
[81334.486515] pending state change SNK_DEBOUNCED -> SNK_UNATTACHED @ 20 ms [rev3 NONE_AMS]
[81334.506621] state change SNK_DEBOUNCED -> SNK_UNATTACHED [delayed 20 ms]
[81334.506640] Start toggling
[81334.516972] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[81334.592759] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[81334.592773] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[81334.592792] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[81334.762940] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[81334.773557] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_DEBOUNCED, polarity 0, disconnected]
[81334.773570] state change SNK_DEBOUNCED -> SNK_DEBOUNCED [rev3 NONE_AMS]
[81334.773588] pending state change SNK_DEBOUNCED -> SNK_UNATTACHED @ 20 ms [rev3 NONE_AMS]
[81334.793672] state change SNK_DEBOUNCED -> SNK_UNATTACHED [delayed 20 ms]
[81334.793681] Start toggling
[81334.801840] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[81334.878655] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[81334.878672] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[81334.878696] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[81335.048968] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[81335.060684] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_DEBOUNCED, polarity 0, disconnected]
[81335.060754] state change SNK_DEBOUNCED -> SNK_DEBOUNCED [rev3 NONE_AMS]
[81335.060775] pending state change SNK_DEBOUNCED -> SNK_UNATTACHED @ 20 ms [rev3 NONE_AMS]
[81335.080884] state change SNK_DEBOUNCED -> SNK_UNATTACHED [delayed 20 ms]
[81335.080900] Start toggling
```
Cc: stable@vger.kernel.org
Fixes: 599f008c257d ("usb: typec: tcpm: Add callbacks to mitigate wakeups due to contaminant")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231015053108.2349570-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Rockchip RK3588 one of the DWC3 cores is integrated weirdly and
requires two extra clocks to be enabled. Without these extra clocks
hot-plugging USB devices is broken.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231020150022.48725-3-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a reset-controller for supporting Xilinx versal platforms. To reset
the USB controller, get the reset ID from device-tree and using ID trigger
the reset, with the assert and deassert reset controller APIs for USB
controller initialization.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231013125847.20334-1-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
The function mtu3_remove() can only return a non-zero value if
ssusb->dr_mode is neiter USB_DR_MODE_PERIPHERAL nor USB_DR_MODE_HOST nor
USB_DR_MODE_OTG. In this case however the probe callback doesn't succeed
and so the remove callback isn't called at all. So the code branch
resulting in this error path could just be dropped were it not for the
compiler choking on "enumeration value 'USB_DR_MODE_UNKNOWN' not handled
in switch [-Werror=switch]". So instead replace this code path by a
WARN_ON and then mtu3_remove() be converted to return void trivially.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231020151537.2202675-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a driver for the NXP PTN36502 Type-C USB 3.1 Gen 1 and DisplayPort
v1.2 combo redriver.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231020-ptn36502-v2-2-b37a337d463e@fairphone.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 14485de431b0 ("usb: Use device_get_match_data()") dropped the
unconditional use of ci_hdrc_usb2_of_match resulting in this warning:
drivers/usb/chipidea/ci_hdrc_usb2.c:41:34: warning: unused variable 'ci_hdrc_usb2_of_match' [-Wunused-const-variable]
The fix is to drop of_match_ptr() which is not necessary because DT is
always used for this driver.
Fixes: 14485de431b0 ("usb: Use device_get_match_data()")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310131627.M43j234A-lkp@intel.com/
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20231019183015.841460-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add Nuvoton NPCM BMC SoCs support to USB ChipIdea driver.
NPCM SoC includes ChipIdea IP block that is used for USB device controller
mode.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20231017195903.1665260-4-tmaimon77@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding CI_HDRC_FORCE_VBUS_ACTIVE_ALWAYS flag to modify the vbus_active
parameter to active in case the ChipIdea USB IP role is device-only and
there is no otgsc register.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20231017195903.1665260-2-tmaimon77@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switch internal usb-storage quirk value to 64-bit as quirks currently
use all 32 bits.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231016072604.40179-3-gmazyland@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch removes macro that was used only by commit that was reverted
in commit ab4b71644a26 ("USB: storage: fix Huawei mode switching
regression")
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231016072604.40179-2-gmazyland@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a 120ms delay implemented for allowing the XHCI host controller to
detect a U3 wakeup pulse. The intention is to wait for the device to retry
the wakeup event if the USB3 PORTSC doesn't reflect the RESUME link status
by the time it is checked. As per the USB3 specification:
tU3WakeupRetryDelay ("Table 7-12. LTSSM State Transition Timeouts")
This would allow the XHCI resume sequence to determine if the root hub
needs to be also resumed. However, in case there is no device connected,
or if there is only a HSUSB device connected, this delay would still affect
the overall resume timing.
Since this delay is solely for detecting U3 wake events (USB3 specific)
then ignore this delay for the disconnected case and the HSUSB connected
only case.
[skip helper function, rename usb3_connected variable -Mathias ]
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If this driver enables the xHC clocks while resuming from sleep, it calls
clk_prepare_enable() without checking for errors and blithely goes on to
read/write the xHC's registers -- which, with the xHC not being clocked,
at least on ARM32 usually causes an imprecise external abort exceptions
which cause kernel oops. Currently, the chips for which the driver does
the clock dance on suspend/resume seem to be the Broadcom STB SoCs, based
on ARM32 CPUs, as it seems...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: 8bd954c56197 ("usb: host: xhci-plat: suspend and resume clocks")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In some situations where xhci removal happens parallel to xhci_handshake,
we encounter a scenario where the xhci_handshake can't succeed, and it
polls until timeout.
If xhci_handshake runs until timeout it can on some platforms result in
a long wait which might lead to a watchdog timeout.
Add a helper that checks xhci status during the handshake, and exits if
set state is entered. Use this helper in places where xhci_handshake is
called unlocked and has a long timeout. For example xhci command timeout
and xhci reset.
[commit message and code comment rewording -Mathias]
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current function that both removes and frees an interrupter isn't
optimal when using several interrupters. The array of interrupters need
to be protected with a lock while removing interrupters, but the default
xhci spin lock can't be used while freeing the interrupters event ring
segment table as dma_free_coherent() should be called with IRQs enabled.
There is no need to free the interrupter under the lock, so split this
code into separate unlocked free part, and a lock protected remove part.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the low-power states of the underlying platform to enable runtime PM.
If the platform doesn't support runtime D3, then enabling default RPM will
result in the controller malfunctioning, as in the case of hotplug devices
not being detected because of a failed interrupt generation.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The AMD USB host controller (1022:43f7) isn't going into PCI D3 by default
without anything connected. This is because the policy that was introduced
by commit a611bf473d1f ("xhci-pci: Set runtime PM as default policy on all
xHC 1.2 or later devices") only covered 1.2 or later.
The 1.1 specification also has the same requirement as the 1.2
specification for D3 support. So expand the runtime PM as default policy
to all AMD 1.1 devices as well.
Fixes: a611bf473d1f ("xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices")
Link: https://composter.com.ua/documents/xHCI_Specification_for_USB.pdf
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Increase the event ring dequeue pointer for port change events in the
same way as other event types. No need to handle it separately.
This only touches the driver side tracking of event ring dequeue.
Note: this does move forward the event ring dequeue increase for port
change events a bit.
Previously the dequeue was increased before temporarily dropping
the xhci lock while kicking roothub polling.
Now dequeue is increased after re-aquiring the lock.
This should not matter as event ring dequeue is not touched at all by
hub thread. It's only touched in xhci interrupt handler.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
No matter what type of event we receive we want to increase the event
ring dequeue pointer one step for every event that is handled.
For unknown reasons the event ring dequeue increase is done inside the
transfer event handler and port event handler.
As the transfer event handler got more complex and can now loop through
several transfer TRBs on a transfer ring, there were additinal checks
added to avoid increasing event ring dequeue more than one step.
No need for elaborate checks to avoid increasing event ring dequeue
in case the transfer event handler goes through a loop.
Just increasing the event ring dequeue outside the transfer event
handler.
End goal is to increase event ring dequeue in just one place.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_alloc_erst() has global scope even though it's only used in
xhci-mem.c. Declare it static.
xhci_free_erst() was removed by commit b17a57f89f69 ("xhci: Refactor
interrupter code for initial multi interrupter support."), but a
declaration in xhci.h still remains. Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ebd88cf50729 ("xhci: Remove unused defines for ERST_SIZE and
ERST_ENTRIES") removed the ERST_SIZE macro but retained a code comment
explaining the quantity chosen in the macro.
Remove the code comment as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Mathias notes that the ERST_PTR_MASK macro is named as if it's masking
the Event Ring Dequeue Pointer in the ERDP register, but in actuality
it's masking the inverse.
Invert the macro's value for clarity.
Migrate it to the modern GENMASK_ULL() syntax to avoid u64 casts.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ring segments have just been amended with a monotonically increasing
number.
To allow developers to inspect the segment numbers and ensure
correctness in particular after ring expansion, expose them in each
ring's "trbs" file in debugfs.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When expanding a ring at its "end", ring->last_seg needs to be updated
for Event Rings as well, not just for all the other ring types.
This is not a fix because ring expansion currently isn't done on the
Event Ring. It's just in preparation for when it's added.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Initial xhci_ring allocation has just been amended to assign a
monotonically increasing number to each ring segment.
However rings may be expanded after initial allocation.
So number newly inserted segments starting from the preceding segment in
the ring and renumber all segments succeeding the newly inserted ones.
This is not a fix because ring expansion currently isn't done on the
Event Ring and that's the only ring type using the segment number.
It's just in preparation for when either Event Ring expansion is added
or when other ring types start making use of the segment number.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
Event Ring is drained by the kernel.
Commit dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer
on purpose") mitigated the issue by advancing the Event Ring Dequeue
Pointer already after half a segment has been processed. Nevertheless,
providing a larger Event Ring would be useful to cope with load peaks.
Expand the number of event TRB slots available by increasing the number
of Event Ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, but with up to 32k it can be excessively high
(sec 5.3.4). So cap the actual number at 2 (configurable through the
ERST_MAX_SEGS macro), which seems like a reasonable quantity. It is
supported by any xHC because the limit in the HCSPARAMS2 register is
defined as a power of 2. Renesas uPD720201 and VIA VL805 controllers
do not support more than 2 ERST entries.
An alternative to increasing the number of Event Ring segments would be
an increase of the segment size. But that requires allocating multiple
contiguous pages, which may be impossible if memory is fragmented.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using more than one Event Ring segment (ERSTSZ > 1), software shall
set the DESI bits in the ERDP register to the number of the segment to
which the upper ERDP bits are pointing. The xHC may use the DESI bits
as a shortcut to determine whether it needs to check for an Event Ring
Full condition: If it's enqueueing events in a different segment, it
need not compare its internal Enqueue Pointer with the Dequeue Pointer
in the upper bits of the ERDP register (sec 5.5.2.3.3).
Not setting the DESI bits correctly can result in the xHC enqueueing
events past the Dequeue Pointer. On Renesas uPD720201 host controllers,
incorrect DESI bits cause an interrupt storm. For comparison, VIA VL805
host controllers do not exhibit such problems. Perhaps they do not take
advantage of the optimization afforded by the DESI bits.
To fix the issue, assign the segment number to each struct xhci_segment
in xhci_segment_alloc(). When advancing the Dequeue Pointer in
xhci_update_erst_dequeue(), write the segment number to the DESI bits.
On driver probe, set the DESI bits to zero in xhci_set_hc_event_deq() as
processing starts in segment 0. Likewise on driver teardown, clear the
DESI bits to zero in xhci_free_interrupter() when clearing the upper
bits of the ERDP register. Previously those functions (incorrectly)
treated the DESI bits as if they're declared RsvdP.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The next_trb() helper relies on a link TRB at the end of a ring segment
to know a segment ends. This works well with transfer rings that use
link trbs, but not with event rings.
Event rings segments are always filled by host to segment size
before moving to next segment. It does not use link TRBs
Check for both link trb and full segment in next_trb() helper to
support event rings.
Useful if several interrupters with several event rings are supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With several xhci controllers active at the same time its hard to
keep track of ports without knowing bus number
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want to trace other port structure members than just port number
so pass entire port structure as parameter instead of just port number.
Dig the port number from the port structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.6-rc7
Here are some new modem device ids, including an entry needed for Sierra
EM9191 which stopped working with recent firmware.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.6-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom to DELL custom modem FM101R-GL
USB: serial: option: add entry for Sierra EM9191 with new firmware
USB: serial: option: add Telit LE910C4-WWX 0x1035 composition
|
|
Convert to using the new inode timestamp accessor functions.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20231004185347.80880-12-jlayton@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Convert to using the new inode timestamp accessor functions.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20231004185347.80880-11-jlayton@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Convert to using the new inode timestamp accessor functions.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20231004185347.80880-10-jlayton@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
The Type-C port drivers can make PM related decisions based
on is the device USB3 or USB2.
Suggested-by: Benson Leung <bleung@chromium.org>
Tested-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231011105825.320062-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding functions that USB hub code can use to inform the
Type-C class about connected USB devices.
Once taken into use, it will allow the Type-C port drivers
to power off components that are not needed, for example if
USB2 device is enumerated, everything that is only relevant
for USB3 (retimers, etc.), can be powered off.
This will also create a symlink "typec" for the USB devices
pointing to the USB Type-C partner device.
Suggested-by: Benson Leung <bleung@chromium.org>
Tested-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231011105825.320062-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
.data of platform_device_info will be copied into .platform_data of
struct device via platform_device_add_data.
However, vhcis[i] contains a spinlock, is dynamically allocated and
used by other code, so it is not meant to be copied. The workaround
was to use void *vhci as an agent, but it was removed in the commit
suggested below.
This patch adds back the workaround and changes the way of using
platform_data accordingly.
Reported-by: syzbot+e0dbc33630a092ccf033@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/00000000000029242706077f3145@google.com/
Reported-by: syzbot+6867a9777f4b8dc4e256@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/0000000000007634c1060793197c@google.com/
Fixes: b8aaf639b403 ("usbip: Use platform_device_register_full()")
Tested-by: syzbot+6867a9777f4b8dc4e256@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/0000000000007ac87d0607979b6b@google.com/
Signed-off-by: Hongren Zheng <i@zenithal.me>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/ZSpHPCaQ5DDA9Ysl@Sun
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB and Thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update the USB serial option driver support for the Fibocom
FM101R-GL LTE modules as there are actually several different variants.
- VID:PID 413C:8213, FM101R-GL are laptop M.2 cards (with
MBIM interfaces for Linux)
- VID:PID 413C:8215, FM101R-GL ESIM are laptop M.2 cards (with
MBIM interface for Linux)
0x8213: mbim, tty
0x8215: mbim, tty
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=413c ProdID=8213 Rev= 5.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=Fibocom FM101-GL Module
S: SerialNumber=a3b7cbf0
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=896mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=413c ProdID=8215 Rev= 5.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=Fibocom FM101-GL Module
S: SerialNumber=a3b7cbf0
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=896mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Puliang Lu <puliang.lu@fibocom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In some cases, like with multiple LUN targets or where the target has to
respond to transport level requests from the receiving context it can be
better to defer cmd submission to a helper thread. If the backend driver
blocks on something like request/tag allocation it can block the entire
target submission path and other LUs and transport IO on that session.
In other cases like single LUN targets with storage that can support all
the commands that the target can queue, then it's best to submit the cmd
to the backend from the target's cmd receiving context.
Subsequent commits will allow the user to config what they prefer, but
drivers like loop can't directly submit because they can be called from a
context that can't sleep. And, drivers like vhost-scsi can support direct
submission, but need to keep their default behavior of deferring execution
to avoid possible regressions where the backend can block.
Make the drivers tell LIO core if they support direct submissions and their
current default, so we can prevent users from misconfiguring the system and
initialize devices correctly.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230928020907.5730-2-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
