| Age | Commit message (Collapse) | Author |
|---|
|
A dedicated wakeup irq will be used to handle runtime suspend/resume,
we use dev_pm_set_dedicated_wake_irq API to take care of requesting
and attaching wakeup irq, then the suspend/resume framework will help
to enable/disable wakeup irq.
The runtime PM is default off since some platforms may not support it.
users can enable it via power/control (set "auto") in sysfs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618031406-15347-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Return error number if encounter errors during suspend and resume.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618031406-15347-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a PD charger advertising Rp-3.0 is connected to a sink port, the
sink port current limit would 3A, during SNK_DISCOVERY, till power
negotiation starts. Once the negotiation starts the power limit needs
to drop down to pSnkStby(500mA @ 5V) and to negotiated current limit
once the explicit contract is in place. Not all charging loops can ramp
up to 3A and drop down to 500mA within tSnkStdby which is 15ms. The port
partner might hard reset if tSnkStdby is not met.
To solve this problem, this patch introduces slow-charger-loop which
when set makes the port request PD_P_SNK_STDBY_MW upon entering
SNK_DISCOVERY(instead of 3A or the 1.5A during SNK_DISCOVERY) and the
actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during
SNK_READY for non-pd link.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
>From PD Spec:
The Sink Shall transition to Sink Standby before a positive or
negative voltage transition of VBUS. During Sink Standby
the Sink Shall reduce its power draw to pSnkStdby. This allows
the Source to manage the voltage transition as well as
supply sufficient operating current to the Sink to maintain PD
operation during the transition. The Sink Shall
complete this transition to Sink Standby within tSnkStdby
after evaluating the Accept Message from the Source. The
transition when returning to Sink operation from Sink Standby
Shall be completed within tSnkNewPower. The
pSnkStdby requirement Shall only apply if the Sink power draw
is higher than this level.
The above requirement needs to be met to prevent hard resets
from port partner.
Without the patch: (5V/3A during SNK_DISCOVERY all the way through
explicit contract)
[ 95.711984] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 95.712007] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 95.712017] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 95.837190] VBUS on
[ 95.882075] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 95.882082] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[ 95.882086] polarity 1
[ 95.883151] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[ 95.883441] enable vbus discharge ret:0
[ 95.883445] Requesting mux state 1, usb-role 2, orientation 2
[ 95.883776] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[ 95.883879] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[ 96.038960] VBUS on
[ 96.383939] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[ 96.383946] Setting voltage/current limit 5000 mV 3000 mA
[ 96.383961] vbus=0 charge:=1
[ 96.386044] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[ 96.386309] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[ 96.394404] PD RX, header: 0x2161 [1]
[ 96.394408] PDO 0: type 0, 5000 mV, 3000 mA [E]
[ 96.394410] PDO 1: type 0, 9000 mV, 2000 mA []
[ 96.394412] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[ 96.394416] Setting usb_comm capable false
[ 96.395083] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[ 96.395089] Requesting PDO 1: 9000 mV, 2000 mA
[ 96.395093] PD TX, header: 0x1042
[ 96.397404] PD TX complete, status: 0
[ 96.397424] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[ 96.400826] PD RX, header: 0x363 [1]
[ 96.400829] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[ 96.400832] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[ 96.577315] PD RX, header: 0x566 [1]
[ 96.577321] Setting voltage/current limit 9000 mV 2000 mA
[ 96.578363] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[ 96.578370] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]
With the patch:
[ 168.398573] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 168.398605] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 168.398619] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 168.522348] VBUS on
[ 168.568676] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 168.568684] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[ 168.568688] polarity 1
[ 168.569867] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[ 168.570158] enable vbus discharge ret:0
[ 168.570161] Requesting mux state 1, usb-role 2, orientation 2
[ 168.570504] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[ 168.570634] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[ 169.070689] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[ 169.070695] Setting voltage/current limit 5000 mV 3000 mA
[ 169.070702] vbus=0 charge:=1
[ 169.072719] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[ 169.073145] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[ 169.077162] PD RX, header: 0x2161 [1]
[ 169.077172] PDO 0: type 0, 5000 mV, 3000 mA [E]
[ 169.077178] PDO 1: type 0, 9000 mV, 2000 mA []
[ 169.077183] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[ 169.077191] Setting usb_comm capable false
[ 169.077753] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[ 169.077759] Requesting PDO 1: 9000 mV, 2000 mA
[ 169.077762] PD TX, header: 0x1042
[ 169.079990] PD TX complete, status: 0
[ 169.080013] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[ 169.083183] VBUS on
[ 169.084195] PD RX, header: 0x363 [1]
[ 169.084200] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[ 169.084206] Setting standby current 5000 mV @ 500 mA
[ 169.084209] Setting voltage/current limit 5000 mV 500 mA
[ 169.084220] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[ 169.260222] PD RX, header: 0x566 [1]
[ 169.260227] Setting voltage/current limit 9000 mV 2000 mA
[ 169.261315] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[ 169.261321] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]
[ 169.261570] AMS POWER_NEGOTIATION finished
Fixes: f0690a25a140b ("staging: typec: USB Type-C Port Manager (tcpm)")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the device doesn't support LPM, make sure to disable the LPM
capability and don't advertise to the host that it supports it.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9e68527ff932b1646f92a7593d4092a903754666.1618366071.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a shutdown callback to USB DWC core driver to ensure that
it is properly shutdown in reboot/shutdown path. This is required
where SMMU address translation is enabled like on SC7180
SoC and few others. If the hardware is still accessing memory after
SMMU translation is disabled as part of SMMU shutdown callback in
system reboot or shutdown path, then IOVAs(I/O virtual address)
which it was using will go on the bus as the physical addresses which
might result in unknown crashes (NoC/interconnect errors).
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Link: https://lore.kernel.org/r/1618380209-20114-1-git-send-email-sanm@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the controller handles single stream only. So, Ignore Packet
Pending bit for stream selection and don't search for another stream if
the host sends Data Packet with PP=0 (for OUT direction) or ACK with
NumP=0 and PP=0 (for IN direction). This slightly improves the stream
performance.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/097ba9e104c143f7ba0195ebff29390ec3043692.1618282705.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is another branded 8153 device that doesn't work well with LPM
enabled:
[ 400.597506] r8152 5-1.1:1.0 enx482ae3a2a6f0: Tx status -71
So disable LPM to resolve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1922651
Link: https://lore.kernel.org/r/20210412135455.791971-1-kai.heng.feng@canonical.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Smatch complains about a potential missing error code:
drivers/usb/typec/port-mapper.c:168 typec_link_port()
warn: missing error code 'ret'
This is a false positive and returning zero is intentional. Let's
re-arrange the code to silence the warning and make the intent more
clear.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YHadaACH8Mq/10F7@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that the xr_serial got support for other models, add their USB IDs
as well.
The Maxlinear/Exar USB UARTs can be used in either ACM mode using the
cdc-acm driver or in "custom driver" mode in which further features such
as hardware and software flow control, GPIO control and in-band
line-status reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
correctly.
Ensure that cdc_acm will not bind to these devices if the custom
USB-serial driver is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/5155887a764cbc11f8da0217fe08a24a77d120b4.1616571453.git.mchehab+huawei@kernel.org
[ johan: rewrite commit message, clean up entries ]
Cc: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add another copyright notice for the work done in 2021.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Reset the transmit and receive FIFOs before enabling the UARTs as part
of open() in order to flush any stale data.
Note that the XR21V141X needs a type-specific implementation due to its
UART Manager registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The XR22801, XR22802 and XR22804 are compound devices with an embedded
hub and up to seven downstream USB devices including one, two or four
UARTs respectively.
The UART function is similar to XR21B142X but most registers are offset
by 0x40, the register requests are different and are directed at the
device rather than interface, and 5 and 6-bit words are not supported.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The single-port XR21B1411 is similar to the XR21B142X type but uses
12-bit registers and 16-bit register addresses, the register requests
are different and are directed at the device rather than interface, and
5 and 6-bit words are not supported.
The register layout is very similar to XR21B142X except that most
registers are offset by 0xc00 (corresponding to a channel index of 12 in
the MSB of wIndex). As the device is single-port so that the derived
channel index is 0, the current register accessors can be reused after
simply changing the address width.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The XR21B1421, XR21B1422 and XR21B1424 are the one-, two- and four-port
models of a second XR21B142X type of the Maxlinear/Exar USB UARTs.
The XR21B142X type differs from XR21V141X in several ways, including:
- register layout
- register width (16-bit instead of 8-bit)
- vendor register requests
- UART enable/disable sequence
- custom-driver mode flag
- three additional GPIOs (9 instead of 6)
As for XR21V141X, the XR21B142X vendor requests encode the channel index
in the MSB of wIndex, but it lacks the UART Manager registers which
have been replaced by regular UART registers. The new type also uses the
interface number of the control interface (0, 2, 4, 6) as channel index
instead of the channel number (0, 1, 2, 3).
The XR21B142X lacks the divisor and format registers used by XR21V141X
and instead uses the CDC SET_LINE_CONTROL request to configure the line
settings.
Note that the currently supported XR21V141X type lacks the custom-driver
mode flag that prevents the device from entering CDC-ACM mode when a CDC
requests is received. This specifically means that the SET_LINE_CONTROL
request cannot be used with XR21V141X even though it is otherwise
supported.
The UART enable sequence for XR21B142X does not involve explicitly
enabling the FIFOs, but according to datasheet the UART must be disabled
when writing any register but GPIO_SET, GPIO_CLEAR, TX_BREAK and
ERROR_STATUS.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
There are at least four types of Maxlinear/Exar USB UARTs which differ
in various ways such as in their register layouts:
XR21V141X
XR21B142X
XR21B1411
XR22804
It is not clear whether the device type can be inferred from the
descriptors so encode it in the device-id table for now.
Add a type structure that can be used to abstract the register layout
and other features, and use it when accessing the XR21V141X UART
registers that are shared by all types.
Note that the currently supported XR21V141X type is the only type that
has a set of UART Manager registers and that these will need to be
handled specifically.
Similarly, XR21V141X is the only type which has the divisor registers
and that needs to use the format register when configuring the line
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In preparation for adding support for further types, drop the type
prefix from defines that are not specific to XR21V141X.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
There's no need to configure the pins on every open and judging from the
vendor driver and datasheet it can be done before enabling the UART.
Move pin configuration from open() to port probe and make sure to
deassert DTR and RTS after configuring all pins as GPIO.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Rename the GPIO-pin defines so that they reflect how they are used.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Rename the GPIO mode defines so that they reflect the datasheet and how
they are used.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add support for the two- and four-port variants of XR21V1410.
Use the interface number of each control interface (e.g. 0, 2, 4, 6) to
derive the zero-based channel index:
XR21V1410 0
XR21V1412 0, 1
XR21V1414 0, 1, 2, 3
Note that the UART registers reside in separate blocks per channel,
while the UART Manager functionality is implemented using per-channel
registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Remove the random white space from the CSIZE switch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Replace the remaining uses of user-space __XX types.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add two port-command helpers to handle the UART module-id parameter
instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Make the vendor-request helpers data parameters be void pointers and
drop the caller casts.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Drop unnecessary packed attributes from structures that don't need it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Drop unnecessary packed attributes from structures that don't need it
and use the __packed macro consistently.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Use kernel types consistently by replacing the remaining __uXX types.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add a read-port-command helper analogous to the send-port-command
helper to take care of the UART module id instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add a send-port-command helper which takes care of determining the UART
module id when sending commands instead of doing so at every call site.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Clean up the vendor-request helpers by using kernel-types consistently
and using void pointers for the data arguments, which allows removing
a cast from one caller.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Unlike the TUSB5052, the TUSB3410 has an LSR TEMT bit to tell if both
the transmitter data and shift registers are empty.
Make sure to check also the shift register on TUSB3410 when waiting for
the transmit buffer to drain during close and drop the time-based
one-char delay which is otherwise needed (e.g. 90 ms at 110 bps).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The three-character drain delay was added by commit f1175daa5312 ("USB:
ti_usb_3410_5052: kill custom closing_wait") when removing the custom
closing-wait implementation, which used a fixed 20 ms poll period and
drain delay.
This was likely a bit too conservative as a one-character timeout (e.g.
33 ms at 300 bps) should be enough to compensate for the lack of a
transmitter empty bit in the TUSB5052 line-status register.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Document that the device line-status register doesn't tell when the
transmitter shift register has emptied and that this is why the
one-character drain delay is needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The f81232 driver now waits for the transmit FIFO to drain during close
so there is no need to keep the time-based drain delay, which would add
up to two seconds on every close for low line speeds.
Fixes: 98405f81036d ("USB: serial: f81232: add tx_empty function")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
When dwc2 core is in clock gating mode loading driver
again causes driver fail. Because in that mode
registers are not accessible.
Added a flow of exiting clock gating mode
to avoid the driver reload failure.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073731.3C81BA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If not hibernation nor partial power down are supported,
port resume is done using the clock gating programming flow.
Adds a new flow of exiting clock gating when PC is
resumed.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073723.BA0FEA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If not hibernation nor partial power down are supported,
clock gating is used to save power.
Adds a new flow of entering clock gating when PC is
suspended.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073716.30C13A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When core is in clock gating state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.
Added exit from clock gating state to avoid port
reset issue and process upper layer request properly.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073708.ADFC6A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Updates the implementation of exiting clock gating mode
when core receives port resume.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_exit_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073701.367E0A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Updates the implementation of entering clock gating mode
when core receives port suspend.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_enter_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073653.9F493A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adds clock gating exit flow when set port feature
reset is received in suspended state.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073646.27217A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added clock gating exit flow from session
request interrupt handler according programming guide.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073638.921E8A0099@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added exit from clock gating mode when wakeup interrupt
is detected. To exit from the clock gating
in device mode "dwc2_gadget_exit_clock_gating()"
function is used with rem_wakeup parameter 0. To exit
clock gating in host mode "dwc2_host_exit_clock_gating()"
with rem_wakeup parameter 1.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073630.EF2CEA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If core doesn't support hibernation or partial power
down power saving options, power can still be saved
using clock gating on all the clocks.
- Added entering clock gating state from USB_SUSPEND
interrupt.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073623.65355A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added host clock gating support functions according
programming guide.
Added function names:
dwc2_host_enter_clock_gating()
dwc2_host_exit_clock_gating()
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073615.B3E84A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added device clock gating support functions according
programming guide.
Moved "bus_suspended" flag to "dwc2_hsotg" struct because
we need to set that flag while entering to clock gating
in case when the driver is built in peripheral mode.
Added function names:
dwc2_gadget_enter_clock_gating()
dwc2_gadget_exit_clock_gating()
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073607.F41E8A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Several Cadence3 improvements are introduced in v5.13-rc1:
- Add recovery during resume if the controller was lost power at system suspend
- Reduce DMA memory footprint
- Other small improvements
* tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fixes issue with Configure Endpoint command
usb: cdnsp: remove redundant initialization of variable ret
usb: cdns3: delete repeated clear operations
usb: cdns3: Optimize DMA request buffer allocation
usb: cdns3: Use dma_pool_* api to alloc trb pool
usb: cdns3: fix static checker warning.
usb: cdns3: imx: mark cdns_imx_system_resume as __maybe_unused
usb: cdns3: trace: delete the trace parameter for request->trb
usb: cdns3: imx: add power lost support for system resume
usb: cdns3: add power lost support for system resume
|
|
This reverts commit 63cd78617350dae99cc5fbd8f643b83ee819fe33 as it
causes a build error:
depmod: ERROR: Cycle detected: usbcore -> typec -> usbcore
depmod: ERROR: Found 2 modules in dependency cycles!
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20210412213655.3776e15e@canb.auug.org.au
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch adds flag EP_UNCONFIGURED to detect whether endpoint was
unconfigured. This flag is set in cdnsp_reset_device after Reset Device
command. Among others this command disables all non control endpoints.
Flag is used in cdnsp_gadget_ep_disable to protect controller against
invoking Configure Endpoint command on disabled endpoint. Lack of this
protection in some cases caused that Configure Endpoint command completed
with Context State Error code completion.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
|
