| Age | Commit message (Collapse) | Author |
|---|
|
During conversion to use GPIO descriptors the device pointer,
which is applied to devm_gpiod_get(), is not yet initialized.
Move initialization in the ->probe() in order to have it set before use.
Fixes: e20849a8c883 ("usb: gadget: pch_udc: Convert to use GPIO descriptors")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a12138 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
Fixes: d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc")
Fixes: 9903b6bedd38 ("usb: gadget: pch-udc: fix lock")
Fixes: 1d23d16a88e6 ("usb: gadget: pch_udc: reorder spin_[un]lock to avoid deadlock")
Cc: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Kernel doc and the content described by it shouldn't be torn apart.
Otherwise validator is not happy:
.../pch_udc.c:573: warning: expecting prototype for pch_udc_reconnect(). Prototype was for pch_udc_init() instead
Fixes: 1c575d2d2e3f ("usb: gadget: pch_udc: Fix usb/gadget/pch_udc: Fix ether gadget connect/disconnect issue")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DMA mapping might fail, we have to check it with dma_mapping_error().
Otherwise DMA-API is not happy:
DMA-API: pch_udc 0000:02:02.4: device driver failed to check map error[device address=0x00000000027ee678] [size=64 bytes] [mapped as single]
Fixes: abab0c67c061 ("usb: pch_udc: Fixed issue which does not work with g_serial")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since we have a separate routine for VBUS sense, the interrupt may occur
before gadget driver is present. Hence, ->setup() call may oops the kernel:
[ 55.245843] BUG: kernel NULL pointer dereference, address: 00000010
...
[ 55.245843] EIP: pch_udc_isr.cold+0x162/0x33f
...
[ 55.245843] <IRQ>
[ 55.245843] ? pch_udc_svc_data_out+0x160/0x160
Check if driver is present before calling ->setup().
Fixes: f646cf94520e ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:
.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27: expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27: got restricted __le32 [usertype]
Fixes: f646cf94520e ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we replaced the xhci_create_usb3_bos_desc() function. We can
remove it along with the static usb_bos_descriptor structure.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ce0acbbd0bd3c3c3a08e6418ab3bdb431a44bbfd.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current xhci_create_usb3_bos_desc() uses a static bos u8 array and
various magic numbers and offsets making it difficult to extend support
for USB 3.2. Let's rewrite this entire function to support dual-lane in
USB 3.2.
The hub driver matches the port speed ID from the extended port status
to the SSID of the sublink speed attributes to detect if the device
supports SuperSpeed Plus. Currently we don't provide the default gen1x2
and gen2x2 sublink speed capability descriptor for USB 3.2 roothub. The
USB stack depends on this to detect and match the correct speed.
In addition, if the xHCI host provides Protocol Speed ID (PSI)
capability, then make sure to convert Protocol Speed ID Mantissa and
Exponent (PSIM & PSIE) to lane speed for gen1x2 and gen2x2.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/19cd09b03f96346996270579fd27d38b8a6844aa.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some hosts incorrectly use sub-minor version for minor version (i.e.
0x02 instead of 0x20 for bcdUSB 0x320 and 0x01 for bcdUSB 0x310).
Currently the xHCI driver works around this by just checking for minor
revision > 0x01 for USB 3.1 everywhere. With the addition of USB 3.2,
checking this gets a bit cumbersome. Since there is no USB release with
bcdUSB 0x301 to 0x309, we can assume that sub-minor version 01 to 09 is
incorrect. Let's try to fix this and use the minor revision that matches
with the USB/xHCI spec to help with the version checking within the
driver.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ed330e95a19dc367819c5b4d78bf7a541c35aa0a.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Initialize USB 3.x root hub SuperSpeed Plus rate.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f1698a96d5f9dfaefb857b95e5db6135ae0c9e93.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drivers/usb/gadget/function/f_fs.c:3829:8-15: WARNING opportunity for memdup_user
Use memdup_user rather than duplicating its implementation
This is a little bit restricted to reduce false positives
Generated by: scripts/coccinelle/api/memdup_user.cocci
Fixes: 8704fd73bf56 ("USB: gadget: f_fs: remove likely/unlikely")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210308070951.GA83949@8a16bdd473dc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When usb_otg_descriptor_alloc() returns NULL to usb_desc, no error
return code of msg_bind() is assigned.
To fix this bug, status is assigned with -ENOMEM in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210323123648.3997-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This LTE modem (M.2 card) has a bug in its power management:
there is some kind of race condition for U3 wake-up between the host and
the device. The modem firmware sometimes crashes/locks when both events
happen at the same time and the modem fully drops off the USB bus (and
sometimes re-enumerates, sometimes just gets stuck until the next
reboot).
Tested with the modem wired to the XHCI controller on an AMD 3015Ce
platform. Without the patch, the modem dropped of the USB bus 5 times in
3 days. With the quirk, it stayed connected for a week while the
'runtime_suspended_time' counter incremented as excepted.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210319124802.2315195-1-vpalatin@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not log the successful-probe message until the tty device has been
registered.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to always claim the data interface and bail out if binding
fails.
Note that the driver had a check to verify that the data interface was
not already bound to a driver but would not detect other failures (e.g.
if the interface was not authorised).
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use negation consistently throughout the driver for NULL checks.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Name the probe error labels after what they do rather than using
sequence numbers which is harder to review and maintain (e.g. may
require renaming unrelated labels when a label is added or removed).
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's no need to clear the interface driver data on failed probe (and
driver core will clear it anyway).
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interface driver data has already been set by
usb_driver_claim_interface() so drop the redundant subsequent
assignment.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If tty-device registration fails the driver would fail to release the
data interface. When the device is later disconnected, the disconnect
callback would still be called for the data interface and would go about
releasing already freed resources.
Fixes: c93d81955005 ("usb: cdc-acm: fix error handling in acm_probe()")
Cc: stable@vger.kernel.org # 3.9
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If tty-device registration fails the driver copy of any Country
Selection functional descriptor would end up being freed twice; first
explicitly in the error path and then again in the tty-port destructor.
Drop the first erroneous free that was left when fixing a tty-port
resource leak.
Fixes: cae2bc768d17 ("usb: cdc-acm: Decrement tty port's refcount if probe() fail")
Cc: stable@vger.kernel.org # 4.19
Cc: Jaejoong Kim <climbbb.kim@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This failure is so common that logging an error here amounts
to spamming log files.
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210311130126.15972-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We have a cycle of callbacks scheduling works which submit
URBs with thos callbacks. This needs to be blocked, stopped
and unblocked to untangle the circle.
The issue leads to faults like:
[ 55.068392] Unable to handle kernel paging request at virtual address 6b6b6c03
[ 55.075624] pgd = be866494
[ 55.078335] [6b6b6c03] *pgd=00000000
[ 55.081924] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 55.087238] Modules linked in: ppp_async crc_ccitt ppp_generic slhc
xt_TCPMSS xt_tcpmss xt_hl nf_log_ipv6 nf_log_ipv4 nf_log_common
xt_policy xt_limit xt_conntrack xt_tcpudp xt_pkttype ip6table_mangle
iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4
iptable_mangle ip6table_filter ip6_tables iptable_filter ip_tables
des_generic md5 sch_fq_codel cdc_mbim cdc_wdm cdc_ncm usbnet mii
cdc_acm usb_storage ip_tunnel xfrm_user xfrm6_tunnel tunnel6
xfrm4_tunnel tunnel4 esp6 esp4 ah6 ah4 xfrm_algo xt_LOG xt_LED
xt_comment x_tables ipv6
[ 55.134954] CPU: 0 PID: 82 Comm: kworker/0:2 Tainted: G
T 5.8.17 #1
[ 55.142526] Hardware name: Freescale i.MX7 Dual (Device Tree)
[ 55.148304] Workqueue: events acm_softint [cdc_acm]
[ 55.153196] PC is at kobject_get+0x10/0xa4
[ 55.157302] LR is at usb_get_dev+0x14/0x1c
[ 55.161402] pc : [<8047c06c>] lr : [<80560448>] psr: 20000193
[ 55.167671] sp : bca39ea8 ip : 00007374 fp : bf6cbd80
[ 55.172899] r10: 00000000 r9 : bdd92284 r8 : bdd92008
[ 55.178128] r7 : 6b6b6b6b r6 : fffffffe r5 : 60000113 r4 : 6b6b6be3
[ 55.184658] r3 : 6b6b6b6b r2 : 00000111 r1 : 00000000 r0 : 6b6b6be3
[ 55.191191] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
[ 55.198417] Control: 10c5387d Table: bcf0c06a DAC: 00000051
[ 55.204168] Process kworker/0:2 (pid: 82, stack limit = 0x9bdd2a89)
[ 55.210439] Stack: (0xbca39ea8 to 0xbca3a000)
[ 55.214805] 9ea0: bf6cbd80 80769a50 6b6b6b6b 80560448 bdeb0500 8056bfe8
[ 55.222991] 9ec0: 00000002 b76da000 00000000 bdeb0500 bdd92448 bca38000 bdeb0510 8056d69c
[ 55.231177] 9ee0: bca38000 00000000 80c050fc 00000000 bca39f44 09d42015 00000000 00000001
[ 55.239363] 9f00: bdd92448 bdd92438 bdd92000 7f1158c4 bdd92448 bca2ee00 bf6cbd80 bf6cef00
[ 55.247549] 9f20: 00000000 00000000 00000000 801412d8 bf6cbd98 80c03d00 bca2ee00 bf6cbd80
[ 55.255735] 9f40: bca2ee14 bf6cbd98 80c03d00 00000008 bca38000 80141568 00000000 80c446ae
[ 55.263921] 9f60: 00000000 bc9ed880 bc9f0700 bca38000 bc117eb4 80141524 bca2ee00 bc9ed8a4
[ 55.272107] 9f80: 00000000 80147cc8 00000000 bc9f0700 80147b84 00000000 00000000 00000000
[ 55.280292] 9fa0: 00000000 00000000 00000000 80100148 00000000 00000000 00000000 00000000
[ 55.288477] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 55.296662] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[ 55.304860] [<8047c06c>] (kobject_get) from [<80560448>] (usb_get_dev+0x14/0x1c)
[ 55.312271] [<80560448>] (usb_get_dev) from [<8056bfe8>] (usb_hcd_unlink_urb+0x50/0xd8)
[ 55.320286] [<8056bfe8>] (usb_hcd_unlink_urb) from [<8056d69c>] (usb_kill_urb.part.0+0x44/0xd0)
[ 55.329004] [<8056d69c>] (usb_kill_urb.part.0) from [<7f1158c4>] (acm_softint+0x4c/0x10c [cdc_acm])
[ 55.338082] [<7f1158c4>] (acm_softint [cdc_acm]) from [<801412d8>] (process_one_work+0x19c/0x3e8)
[ 55.346969] [<801412d8>] (process_one_work) from [<80141568>] (worker_thread+0x44/0x4dc)
[ 55.355072] [<80141568>] (worker_thread) from [<80147cc8>] (kthread+0x144/0x180)
[ 55.362481] [<80147cc8>] (kthread) from [<80100148>] (ret_from_fork+0x14/0x2c)
[ 55.369706] Exception stack(0xbca39fb0 to 0xbca39ff8)
Tested-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210311130126.15972-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Counting break events is nice but we should actually report them to
the tty layer.
Fixes: 5a6a62bdb9257 ("cdc-acm: add TIOCMIWAIT")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20210311133714.31881-1-oneukum@suse.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
init_dma_pools() calls dma_pool_create(...dev->dev) to create dma pool.
however, dev->dev is actually set after calling init_dma_pools(), which
effectively makes dma_pool_create(..NULL) and cause crash.
To fix this issue, init dma only after dev->dev is set.
[ 1.317993] RIP: 0010:dma_pool_create+0x83/0x290
[ 1.323257] Call Trace:
[ 1.323390] ? pci_write_config_word+0x27/0x30
[ 1.323626] init_dma_pools+0x41/0x1a0 [snps_udc_core]
[ 1.323899] udc_pci_probe+0x202/0x2b1 [amd5536udc_pci]
Fixes: 7c51247a1f62 (usb: gadget: udc: Provide correct arguments for 'dma_pool_create')
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210317230400.357756-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It seems that on Intel Merrifield platform the USB PHY shouldn't be suspended.
Otherwise it can't be enabled by simply change the cable in the connector.
Enable corresponding quirk for the platform in question.
Fixes: e5f4ca3fce90 ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210322125244.79407-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the gadget driver doesn't specify a max_speed, then use the
controller's maximum supported speed as default. For DWC_usb32 IP, the
gadget's speed maybe limited to gen2x1 rate only if the driver's
max_speed is unknown. This scenario should not occur with the current
implementation since the default gadget driver's max_speed should always
be specified. However, to make the driver more robust and help with
readability, let's cover all the scenarios in __dwc3_gadget_set_speed().
Fixes: 450b9e9fabd8 ("usb: dwc3: gadget: Set speed only up to the max supported")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/55ac7001af73bfe9bc750c6446ef4ac8cf6f9313.1615254129.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Set the dwc->gadget_max_speed to SuperSpeed Plus if the user sets the
ssp_rate. The udc_set_ssp_rate() is intended for setting the gadget's
speed to SuperSpeed Plus at the specified rate.
Fixes: 072cab8a0fe2 ("usb: dwc3: gadget: Implement setting of SSP rate")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/0b2732e2f380d9912ee87f39dc82c2139223bad9.1615254129.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ACPI probe starts failing since commit bea46b981515 ("usb: dwc3:
qcom: Add interconnect support in dwc3 driver"), because there is no
interconnect support for ACPI, and of_icc_get() call in
dwc3_qcom_interconnect_init() will just return -EINVAL.
Fix the problem by skipping interconnect init for ACPI probe, and then
the NULL icc_path_ddr will simply just scheild all ICC calls.
Fixes: bea46b981515 ("usb: dwc3: qcom: Add interconnect support in dwc3 driver")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210311060318.25418-1-shawn.guo@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check for usb_device->ssp_rate to output the signaling rate for genXxY.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/80a3214592b30da6ca95bb87984f2a9779de0b14.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check for usb_device->ssp_rate to print the SuperSpeed Plus signaling
rate generation and lane count.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/df0986bbe92251c104dd92e3c796df7c4f2674ce.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The get_port_ssp_rate() can replace port_speed_is_ssp(). If the port
speed is detected to be in gen2x1, gen1x2, or gen2x2, then the port is
operating at SuperSpeed Plus.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/dfd61ae637597bad502d2420b4dbd3774fc76aab.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce ssp_rate field to usb_device structure to capture the
connected SuperSpeed Plus signaling rate generation and lane count with
the corresponding usb_ssp_rate enum.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b7805d121e5ae4ad5ae144bd860b6ac04ee47436.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current dwc3_gadget_reset_interrupt() will stop any active
transfers, but only addresses blocking of EP queuing for while we are
coming from a disconnected scenario, i.e. after receiving the disconnect
event. If the host decides to issue a bus reset on the device, the
connected parameter will still be set to true, allowing for EP queuing
to continue while we are disabling the functions. To avoid this, set the
connected flag to false until the stop active transfers is complete.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616146285-19149-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add checks similar to dwc3_gadget_ep_queue() before kicking off
transfers after getting an endpoint completion event. Since cleaning
up completed requests will momentarily unlock dwc->lock, there is a
chance for a sequence like pullup disable to be executed. This can
lead to preparing a TRB, which will be removed by the pullup disable
routine.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616146285-19149-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Force-threaded interrupt handlers used to run with interrupts enabled,
something which could lead to deadlocks in case a threaded handler
shared a lock with code running in hard interrupt context (e.g. timer
callbacks) and did not explicitly disable interrupts.
Since commit 81e2073c175b ("genirq: Disable interrupts for force
threaded handlers") interrupt handlers always run with interrupts
disabled on non-RT so that drivers no longer need to do handle forced
threading ("threadirqs").
Drop the now obsolete workaround added by commit 63aea0dbab90 ("USB:
xhci: fix lock-inversion problem").
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322111140.32056-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These were added in commit 780cc0f370 ("usb: gadget: add '__ref' for
rndis_config_register() and cdc_config_register()") to silence
modpost, but they didn't fix the real problem - that was fixed later
by removing wrong __init annotations in commit c94e289f195e ("usb:
gadget: remove incorrect __init/__exit annotations").
It really never makes sense for a function to be marked __ref unless
it (1) has some conditional that chooses whether to call an __init
function (or access __initdata) or not and (2) has a comment
explaining why the __ref is there and why it is safe.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20210323081607.405904-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Usage of strlcpy in Linux Kernel has been recently
deprecated [1], convert driver to strscpy
[1] https://lore.kernel.org/lkml/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614603943-11668-2-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
User can configure f_uac1 function via p_chmask/c_chmask
whether uac1 shall support playback and/or capture,
but it has only effect on the created ALSA device,
but not on the USB descriptor.
This patch adds playback/capture descriptors
dependent on that parameter. It is similar to
the same conversion done earlier for f_uac2
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-6-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently user can configure UAC1 function with
parameters that violate UAC1 spec or are not supported
by UAC1 gadget implementation.
This can lead to incorrect behavior if such gadget
is connected to the host - like enumeration failure
or other issues depending on host's UAC1 driver
implementation, bringing user to a long hours
of debugging the issue.
Instead of silently accept these parameters, throw
an error if they are not valid.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-5-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently user can configure UAC2 function with
parameters that violate UAC2 spec or are not supported
by UAC2 gadget implementation.
This can lead to incorrect behavior if such gadget
is connected to the host - like enumeration failure
or other issues depending on host's UAC2 driver
implementation, bringing user to a long hours
of debugging the issue.
Instead of silently accept these parameters, throw
an error if they are not valid.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-4-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When usb_otg_descriptor_alloc() returns NULL to usb_desc, no error
return code of multi_bind() is assigned.
To fix this bug, status is assigned with -ENOMEM in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210307084545.21775-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch adds support of SS and SSP speed.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210310105216.38202-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Silence deferred probe error caused by the PHY driver which is probed
later than the ChipIdea driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314203927.2572-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes bug with the handling of more than one language in
the string table in f_fs.c.
str_count was not reset for subsequent language codes.
str_count-- "rolls under" and processes u32 max strings on
the processing of the second language entry.
The existing bug can be reproduced by adding a second language table
to the structure "strings" in tools/usb/ffs-test.c.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Link: https://lore.kernel.org/r/20210317224109.21534-1-dean@sensoray.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new driver for supporting Xilinx platforms. This driver is used
for some sequence of operations required for Xilinx USB controllers.
This driver is also used to choose between PIPE clock coming from SerDes
and the Suspend Clock. Before the controller is out of reset, the clock
selection should be changed to PIPE clock in order to make the USB
controller work. There is a register added in Xilinx USB controller
register space for the same.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1615963949-75320-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When __usbhsf_pkt_get() returns NULL to pkt, no error return code of
usbhsf_pkt_handler() is assigned.
To fix this bug, ret is assigned with -EINVAL in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210307090030.22369-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
None of the DWC_usb3x IPs (and all their versions) supports low-speed
setting in device mode. In the early days, our "Early Adopter Edition"
DWC_usb3 databook shows that the controller may be configured to operate
in low-speed, but it was revised on release. Let's remove this invalid
speed setting to avoid any confusion.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/258b1c7fbb966454f4c4c2c1367508998498fc30.1615509438.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The * has been aligned on each line for block comment.
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Link: https://lore.kernel.org/r/20210311190901.gaw7m7ndib3uzakm@kewl-virtual-machine
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A space was given after tab key. The extra space has been removed.
This is done to maintain uniformity in the code.
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Link: https://lore.kernel.org/r/20210311190058.yudmivcbok56itay@kewl-virtual-machine
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
