| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds the support of configfs to MIDI 2.0 function driver
for users to allow configuring the UMP Endpoint and Function Blocks
more flexibly. The configuration is in a tree form. The top-most
contains some card-level configurations. UMP Endpoints are defined in
subdirectories (ep.0, ep.1, etc) that contain Endpoint-specific
configurations such as ep_name, etc. And, UMP Function Blocks are
defined in the subdirectories (block.0, block.1, etc) under EP
subdirectory. As default, the driver creates a single UMP Endpoint
(ep.0) and a single Function Block (block.0) to work in a minimalistic
manner. User can modify those attributes freely to fit with the
demands.
When multiple Function Blocks are required, user can create another
directory as block.1, block.2, and so on (up to block.31). A block.*
directory can be deleted dynamically, too. A caveat is that the block
number has to be continuous.
Similarly, when multiple UMP Endpoints are required, user can create
another directory as ep.1, ep.2, up to ep.3.
Also, some driver behavior can be controlled in the card top-level
configs. e.g. you can pass process_ump=0 to disable the processing of
UMP Stream messages. This would be equivalent with the older MIDI 2.0
spec that doesn't support UMP v1.1 features.
The configfs interface checks upper- / lower-bound of input values,
and more sanity checks are performed at binding.
Attributes can't be changed any longer once when the instance is
linked to UDC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-3-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds the support for USB MIDI 2.0 gadget function driver.
The driver emulates a USB MIDI 2.0 interface with one or more UMP
Endpoints, where each of UMP Endpoint is a pair of MIDI Endpoints for
handling MIDI 2.0 UMP packets. When the function driver is bound, the
driver creates an ALSA card object with UMP rawmidi devices. This is
a kind of loop-back where the incoming and upcoming UMP packets
from/to the MIDI 2.0 UMP Endpoints are transferred as-is. In
addition, legacy (MIDI 1.0) rawmidi devices are created, so that
legacy applications can work in the gadget side, too.
When a USB MIDI 2.0 gadget interface appears, the connected host can
use it with the snd-usb-audio driver where MIDI 2.0 support is
enabled. Both gadget and connected hosts will have the similar UMP
Endpoint and Function Block (or Group Terminal Block) information.
Slight differences are the direction and UI-hint bits; it's due to the
nature of gadget driver, and the input/output direction is swapped in
both sides (the input for gadget is the output for host, and vice
versa).
The driver supports the brand-new UMP v1.1 feature, including the UMP
Stream message handling for providing UMP Endpoint and Function Block
information as well as dealing with the MIDI protocol switch. The
driver responds to UMP Stream messages by itself. OTOH, MIDI-CI
message handling isn't implemented in the kernel driver; it should be
processed in the user-space through the loopback UMP device.
As of this patch, the whole configuration is fixed, providing only one
bidirectional UMP Endpoint containing a single FB/GTB with a single
UMP Group. The configuration will be dynamically changeable in the
following patches.
The traditional MIDI 1.0 is still provided in the altset 0 (which is
mandatory per spec). But it's only about the configuration, and no
actual I/O will be running for the altset 0 as of this patch. The
proper support MIDI 1.0 altset will follow in later patches, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-2-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In Realtek SoC, the parameter of usb phy is designed to can dynamic
tuning base on port status. Therefore, add a notify callback of phy
driver when usb port status change.
The Realtek phy driver is designed to dynamically adjust disconnection
level and calibrate phy parameters. When the device connected bit changes
and when the disconnected bit changes, do port status change notification:
Check if portstatus is USB_PORT_STAT_CONNECTION and portchange is
USB_PORT_STAT_C_CONNECTION.
1. The device is connected, the driver lowers the disconnection level and
calibrates the phy parameters.
2. The device disconnects, the driver increases the disconnect level and
calibrates the phy parameters.
When controller to notify connect that device is already ready. If we
adjust the disconnection level in notify_connect, the disconnect may have
been triggered at this stage. So we need to change that as early as
possible. The status change of connection is before port reset.
Therefore, we add an api to notify phy the port status changes. In this
stage, the device is not port enable, and it will not trigger
disconnection.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230725033318.8361-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename dwc3_data to dwc3_am62 to make it consistent with other
glue drivers, it's clearer that this is am62's specific.
While there, do the same for data variable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Link: https://lore.kernel.org/r/ZLKoHhJvT+Y6aM+C@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For mxs PHY, if there is a vbus but the bus is not enumerated, we need
to force the dp/dm as SE0 from the controller side. If not, there is
possible USB wakeup due to unstable dp/dm, since there is possible no
pull on dp/dm, such as there is a USB charger on the port.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627110353.1879477-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function mxs_phy_is_otg_host() will return true if OTG_ID_VALUE is
0 at USBPHY_CTRL register. However, OTG_ID_VALUE will not reflect the real
state if the ID pin is float, such as Host-only or Type-C cases. The value
of OTG_ID_VALUE is always 1 which means device mode.
This patch will fix the issue by judging the current mode based on
last_event. The controller will update last_event in time.
Fixes: 7b09e67639d6 ("usb: phy: mxs: refine mxs_phy_disconnect_line")
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627110353.1879477-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add USB PHY event for below situation:
- usb role changed
- vbus connect
- vbus disconnect
- gadget driver is enumerated
USB PHY driver can get the last event after above situation occurs
and deal with different situations.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627110353.1879477-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cdns3 just set PHY mode switch for USB3.0 PHY.
If USB 2.0 PHY contains PHY mode switch setting,
USB 2.0 PHY mode function can't be called.
So add PHY mode switch function for USB 2.0 PHY.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230721095923.20445-1-minda.chen@starfivetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In some cases, the user may need to tune the rise/fall time of the
high-speed transmitter waveform for USB Certification. This will add
a parameter for this purpose. The value will be fetched from dtb and
finally written to the register.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627112126.1882666-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In current driver, the value of tuning parameter will not take effect
if samsung,picophy-* is assigned as 0. Because 0 is also a valid value
acccording to the description of USB_PHY_CFG1 register, this will improve
the logic to let it work.
Fixes: 58a3cefb3840 ("usb: chipidea: imx: add two samsung picophy parameters tuning implementation")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627112126.1882666-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Cable type such as active and retimer received as a part of Thunderbolt3
or Thunderbolt4 cable discover mode VDO needs to be configured in the
thunderbolt alternate mode.
Configuring the register bits for this cable type is changed with Intel
Meteor Lake platform. BIT2 for Retimer/Redriver cable and BIT22 for
Active/Passive cable.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20230718024703.1013367-3-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230707073653.3396988-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Detect and report if the Audio Accessory device has been attached to the
corresponding USB-C port.
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20230709200235.265674-1-dmitry.baryshkov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use read_poll_timeout() instead of open coding it.
In the same time, fix the typo in the error message.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710094645.42111-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We should verify the bound of the array to assure that host
may not manipulate the index to point past endpoint array.
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20230628081511.186850-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Lunar Lake IOM has a different IOM port status offset and size
than Intel MTL.
Intel Lunar Lake is the first platform to extend IOM port status
from 32bit to 64bit by adding DDI port number into IOM port status.
Added IOM_PORT_STATUS_REGS macro for using platform specific IOM port
status offset and size.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Madhu M <madhu.m@intel.com>
Link: https://lore.kernel.org/r/20230704080509.14251-1-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Genesys Logic GL3523 is a 4-port USB 3.1 hub that has a reset pin to
toggle and a 5.0V core supply exported though an integrated LDO is
available for powering it.
Add the support for this hub, for controlling the reset pin and the core
power supply.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
[m.felsch@pengutronix.de: include review feedback & port to 6.4]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230623142228.4069084-2-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct i2c_driver::probe_new is about to go away. Switch the driver to
use the probe callback with the same prototype.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230626091314.557122-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that the driver core allows for struct class to be in read-only
memory, remove the usb_class structure and create the usbmisc_class
const class structure declared at build time which places it into
read-only memory, instead of having it to be dynamically allocated
at load time.
Additionally, now we register usb class at startup and unregister it
when shutting down, so we don't have to count uses of the class.
Therefore we don't need the 'usb_class' structure anymore. Due to this
fact, remove all static functions related to class initialization and
deinitialization. We can't use them in 'usb.c' since they are static
and we don't really need them anymore.
Since we have to register the class in usb_init function in 'usb.c'
and use it in 'file.c' as well, declare the usbmisc_class structure
as 'export' in the 'usb.h' file.
Debatable moment: the class registration and unregistration functions
could be extracted to the 'file.c'. I think we don't want to do this
since it would be one-line functions. They would make the code paths
more confusing and add calling overhead.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230621202514.1223670-1-ivan.orlov0322@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The device may be scheduled during the resume process,
so this cannot appear in atomic operations. Since
pm_runtime_set_active will resume suppliers, put set
active outside the spin lock, which is only used to
protect the struct cdns data structure, otherwise the
kernel will report the following warning:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1163
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 651, name: sh
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
CPU: 0 PID: 651 Comm: sh Tainted: G WC 6.1.20 #1
Hardware name: Freescale i.MX8QM MEK (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x30
dump_stack_lvl+0x64/0x80
dump_stack+0x1c/0x38
__might_resched+0x1fc/0x240
__might_sleep+0x68/0xc0
__pm_runtime_resume+0x9c/0xe0
rpm_get_suppliers+0x68/0x1b0
__pm_runtime_set_status+0x298/0x560
cdns_resume+0xb0/0x1c0
cdns3_controller_resume.isra.0+0x1e0/0x250
cdns3_plat_resume+0x28/0x40
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230616021952.1025854-1-xiaolei.wang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Previously, the cdns3_gadget_check_config() function in the cdns3 driver
mistakenly calculated the ep_buf_size by considering only one
configuration's endpoint information because "claimed" will be clear after
call usb_gadget_check_config().
The fix involves checking the private flags EP_CLAIMED instead of relying
on the "claimed" flag.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230707230015.494999-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The legacy gadget driver omitted calling usb_gadget_check_config()
to ensure that the USB device controller (UDC) has adequate resources,
including sufficient endpoint numbers and types, to support the given
configuration.
Previously, usb_add_config() was solely invoked by the legacy gadget
driver. Adds the necessary usb_gadget_check_config() after the bind()
operation to fix the issue.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230707230015.494999-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The buffer address used in sysfs_emit should be aligned to PAGE_SIZE.
Use sysfs_emit_at instead to offset the buffer.
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pointers of each usb_power_delivery handles are stored in "pds"
array returned from the pd_get ops but not in the adjacent memory
calculated from "pd". Get the handles from "pds" array directly instead
of deriving them from "pd".
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When calling device_add in the registration of typec_port, it will do
the NULL check on usb_power_delivery handle in typec_port for the
visibility of the device attributes. It is always NULL because port->pd
is set in typec_port_set_usb_power_delivery which is later than the
device_add call.
Set port->pd before device_add and only link the device after that.
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
device_get_named_child_node() returns NULL, if it fails, replace
IS_ERR() with NULL pointer check.
Fixes: a4422ff22142 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230725125319.565733-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tegra_xudc_powerdomain_init()"
This reverts commit f08aa7c80dac27ee00fa6827f447597d2fba5465.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this driver, the bug means that probe cannot succeed when CONFIG_PM
is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: f08aa7c80dac ("usb: gadget: tegra-xudc: Fix error check in tegra_xudc_powerdomain_init()")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/ZKQoBa84U/ykEh3C@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 18fc7c435be3f17ea26a21b2e2312fcb9088e01f.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this code, the patch means that certain tegra_xusb_probe() will
fail if the firmware supports power-domains but CONFIG_PM is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 18fc7c435be3 ("usb: xhci: tegra: Fix error check")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/8baace8d-fb4b-41a4-ad5f-848ae643a23b@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, increasing raw_dev->count happens before invoke the
raw_queue_event(), if the raw_queue_event() return error, invoke
raw_release() will not trigger the dev_free() to be called.
[ 268.905865][ T5067] raw-gadget.0 gadget.0: failed to queue event
[ 268.912053][ T5067] udc dummy_udc.0: failed to start USB Raw Gadget: -12
[ 268.918885][ T5067] raw-gadget.0: probe of gadget.0 failed with error -12
[ 268.925956][ T5067] UDC core: USB Raw Gadget: couldn't find an available UDC or it's busy
[ 268.934657][ T5067] misc raw-gadget: fail, usb_gadget_register_driver returned -16
BUG: memory leak
[<ffffffff8154bf94>] kmalloc_trace+0x24/0x90 mm/slab_common.c:1076
[<ffffffff8347eb55>] kmalloc include/linux/slab.h:582 [inline]
[<ffffffff8347eb55>] kzalloc include/linux/slab.h:703 [inline]
[<ffffffff8347eb55>] dev_new drivers/usb/gadget/legacy/raw_gadget.c:191 [inline]
[<ffffffff8347eb55>] raw_open+0x45/0x110 drivers/usb/gadget/legacy/raw_gadget.c:385
[<ffffffff827d1d09>] misc_open+0x1a9/0x1f0 drivers/char/misc.c:165
[<ffffffff8154bf94>] kmalloc_trace+0x24/0x90 mm/slab_common.c:1076
[<ffffffff8347cd2f>] kmalloc include/linux/slab.h:582 [inline]
[<ffffffff8347cd2f>] raw_ioctl_init+0xdf/0x410 drivers/usb/gadget/legacy/raw_gadget.c:460
[<ffffffff8347dfe9>] raw_ioctl+0x5f9/0x1120 drivers/usb/gadget/legacy/raw_gadget.c:1250
[<ffffffff81685173>] vfs_ioctl fs/ioctl.c:51 [inline]
[<ffffffff8154bf94>] kmalloc_trace+0x24/0x90 mm/slab_common.c:1076
[<ffffffff833ecc6a>] kmalloc include/linux/slab.h:582 [inline]
[<ffffffff833ecc6a>] kzalloc include/linux/slab.h:703 [inline]
[<ffffffff833ecc6a>] dummy_alloc_request+0x5a/0xe0 drivers/usb/gadget/udc/dummy_hcd.c:665
[<ffffffff833e9132>] usb_ep_alloc_request+0x22/0xd0 drivers/usb/gadget/udc/core.c:196
[<ffffffff8347f13d>] gadget_bind+0x6d/0x370 drivers/usb/gadget/legacy/raw_gadget.c:292
This commit therefore invoke kref_get() under the condition that
raw_queue_event() return success.
Reported-by: syzbot+feb045d335c1fdde5bf7@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Closes: https://syzkaller.appspot.com/bug?extid=feb045d335c1fdde5bf7
Signed-off-by: Zqiang <qiang.zhang1211@gmail.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/20230714074011.20989-1-qiang.zhang1211@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 286d9975a838 ("usb: gadget: udc: core: Prevent soft_connect_store() race")
introduced one extra mutex_unlock of connect_lock in the usb_gadget_active function.
Fixes: 286d9975a838 ("usb: gadget: udc: core: Prevent soft_connect_store() race")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230721222256.1743645-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit b138e23d3dff90c0494925b4c1874227b81bddf7.
AutoRetry has been found to sometimes cause controller freezes when
communicating with buggy USB devices.
This controller feature allows the controller in host mode to send
non-terminating/burst retry ACKs instead of terminating retry ACKs
to devices when a transaction error (CRC error or overflow) occurs.
Unfortunately, if the USB device continues to respond with a CRC error,
the controller will not complete endpoint-related commands while it
keeps trying to auto-retry. [3] The xHCI driver will notice this once
it tries to abort the transfer using a Stop Endpoint command and
does not receive a completion in time. [1]
This situation is reported to dmesg:
[sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00
xhci-hcd: xHCI host not responding to stop endpoint command
xhci-hcd: xHCI host controller not responding, assume dead
xhci-hcd: HC died; cleaning up
Some users observed this problem on an Odroid HC2 with the JMS578
USB3-to-SATA bridge. The issue can be triggered by starting
a read-heavy workload on an attached SSD. After a while, the host
controller would die and the SSD would disappear from the system. [1]
Further analysis by Synopsys determined that controller revisions
other than the one in Odroid HC2 are also affected by this.
The recommended solution was to disable AutoRetry altogether.
This change does not have a noticeable performance impact. [2]
Revert the enablement commit. This will keep the AutoRetry bit in
the default state configured during SoC design [2].
Fixes: b138e23d3dff ("usb: dwc3: core: Enable AutoRetry feature in the controller")
Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1]
Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2]
Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3]
Cc: stable@vger.kernel.org
Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jakub Vanek <linuxtardis@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 5255660b208aebfdb71d574f3952cf48392f4306.
This quirk breaks at least the following hardware:
0b:00.0 0c03: 1106:3483 (rev 01) (prog-if 30 [XHCI])
Subsystem: 1106:3483
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 66
Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/4 Maskable- 64bit+
Address: 00000000fee007b8 Data: 0000
Capabilities: [c4] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 89W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <16us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis+ NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
with the quirk enabled it fails early with
[ 0.754373] pci 0000:0b:00.0: xHCI HW did not halt within 32000 usec status = 0x1000
[ 0.754419] pci 0000:0b:00.0: quirk_usb_early_handoff+0x0/0x7a0 took 31459 usecs
[ 2.228048] xhci_hcd 0000:0b:00.0: xHCI Host Controller
[ 2.228053] xhci_hcd 0000:0b:00.0: new USB bus registered, assigned bus number 7
[ 2.260073] xhci_hcd 0000:0b:00.0: Host halt failed, -110
[ 2.260079] xhci_hcd 0000:0b:00.0: can't setup: -110
[ 2.260551] xhci_hcd 0000:0b:00.0: USB bus 7 deregistered
[ 2.260624] xhci_hcd 0000:0b:00.0: init 0000:0b:00.0 fail, -110
[ 2.260639] xhci_hcd: probe of 0000:0b:00.0 failed with error -110
The hardware in question is an external PCIe card. It looks to me like the quirk
needs to be narrowed down. But this needs information about the hardware showing
the issue this quirk is to fix. So for now a clean revert.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 5255660b208a ("xhci: add quirk for host controllers that don't update endpoint DCS")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230713112830.21773-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Focusrite Scarlett audio device does not behave correctly during
resumes. Below is what happens during every resume (captured with
Beagle 5000):
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset/Target disconnected>
<High Speed>
The Scarlett disconnects and is enumerated again.
However from time to time it drops completely off the USB bus during
resume. Below is captured occurrence of such an event:
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset>/<Chirp K>/<Tiny K>
<High Speed>
<Corrupted packet>
<Reset/Target disconnected>
To fix the condition a user has to unplug and plug the device again.
With USB_QUIRK_RESET_RESUME applied ("usbcore.quirks=1235:8211:b")
for the Scarlett audio device the issue still reproduces.
Applying USB_QUIRK_DISCONNECT_SUSPEND ("usbcore.quirks=1235:8211:m")
fixed the issue and the Scarlett audio device didn't drop off the USB
bus for ~5000 suspend/resume cycles where originally issue reproduced in
~100 or less suspend/resume cycles.
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230724112911.1802577-1-lb@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow devices to have dma operations beyond 64K, and avoid warnings such
as:
DMA-API: xhci-mtk 11200000.usb: mapping sg segment longer than device claims to support [len=98304] [max=65536]
Fixes: 0cbd4b34cda9 ("xhci: mediatek: support MTK xHCI host controller")
Cc: stable <stable@kernel.org>
Tested-by: Zubin Mithra <zsm@chromium.org>
Reported-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20230628-mtk-usb-v2-1-c8c34eb9f229@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on
system_suspend in host mode") replaces check for HOST only dr_mode with
current_dr_role. But during booting, the current_dr_role isn't
initialized, thus the device side reset is always issued even if dwc3
was configured as host-only. What's more, on some platforms with host
only dwc3, aways issuing device side reset by accessing device register
block can cause kernel panic.
Fixes: c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ucsi_unregister_partner()
It's better to set TYPEC_STATE_SAFE mode from ucsi_unregister_partner()
instead of ucsi_partner_change(), ucsi_unregister_partner() is always
when the partner disconnects.
Fixes: 25a2bc21c863 ("usb: typec: ucsi: call typec_set_mode on non-altmode partner change")
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230626-topic-sm8550-usb-c-audio-fixup-v1-1-bc72fddf3f42@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ohci_hcd_at91_drv_suspend() sets ohci->rh_state to OHCI_RH_HALTED when
suspend which will let the ohci_irq() skip the interrupt after resume. And
nobody to handle this interrupt.
According to the comment in ohci_hcd_at91_drv_suspend(), it need to reset
when resume from suspend(MEM) to fix by setting "hibernated" argument of
ohci_resume().
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230626152713.18950-1-aarongt.shen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sort the driver symbols alphabetically in order to make it more obvious
where new driver entries should be added.
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Exar devices like XR21B1411 can control an RS485 transceiver by
automatically asserting the RTS#/RS485 pin before sending data
and deasserting it when the last stop bit has been transmitted.
The polarity of the RST#/RS485 signal is configurable and the
hardware also supports half-duplex turn-around delay and
address matching mode.
Add support for enabling and disabling RS-485 mode and
configuring the RST#/RS485 signal polarity using the TIOCGRS485
and TIOCSRS485 ioctls. Support for half-duplex turn-around delay
and address matching mode are left unimplemented for now.
User enables RS-485 mode by setting SER_RS485_ENABLED flag in
struct serial_rs485 flags. User should also set either
SER_RS485_RTS_ON_SEND or SER_RS485_RTS_AFTER_SEND to select the
behaviour of the RTS#/RS485 pin. Setting SER_RS485_RTS_ON_SEND
will drive RTS#/RS485 low during transmission.
Signed-off-by: Jarkko Sonninen <kasper@iki.fi>
[ johan: let SER_RS485_RTS_ON_SEND determine SER_RS485_RTS_AFTER_SEND ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add the device and product ID for this CAN bus interface / license
dongle. The device is usable either directly from user space or can be
attached to a kernel CAN interface with slcan_attach.
Reported-by: Kaufmann Automotive GmbH <info@kaufmann-automotive.ch>
Tested-by: Kaufmann Automotive GmbH <info@kaufmann-automotive.ch>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
[ johan: amend commit message and move entries in sort order ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add Quectel EC200A "DIAG, AT, MODEM":
0x6005: ECM / RNDIS + DIAG + AT + MODEM
T: Bus=01 Lev=01 Prnt=02 Port=05 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=6005 Rev=03.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0000
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
Signed-off-by: Mohsen Tahmasebi <moh53n@moh53n.ir>
Tested-by: Mostafa Ghofrani <mostafaghrr@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
EM060K_128 is EM060K's sub-model, having the same name "Quectel EM060K-GL"
MBIM + GNSS + DIAG + NMEA + AT + QDSS + DPL
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0128 Rev= 5.04
S: Manufacturer=Quectel
S: Product=Quectel EM060K-GL
S: SerialNumber=f6fa08b6
C:* #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Jerry Meng <jerry-meng@foxmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Message-Id: <20230705190309.579783-18-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the
hardware in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: host: xhci-plat: Set XHCI_STATE_REMOVING before resuming XHCI HC
usb: host: xhci: Do not re-initialize the XHCI HC if being removed
usb: typec: nb7vpq904m: fix CONFIG_DRM dependency
usbip: usbip_host: Replace strlcpy with strscpy
usb: dwc3: gadget: Propagate core init errors to UDC during pullup
USB: serial: option: add LARA-R6 01B PIDs
usb: ulpi: Make container_of() no-op in to_ulpi_dev()
usb: gadget: legacy: fix error return code in gfs_bind
usb: typec: fsa4480: add support for Audio Accessory Mode
usb: typec: fsa4480: rework mux & switch setup to handle more states
usb: typec: ucsi: call typec_set_mode on non-altmode partner change
USB: gadget: f_hid: make hidg_class a static const structure
USB: gadget: f_printer: make usb_gadget_class a static const structure
USB: mon: make mon_bin_class a static const structure
USB: gadget: udc: core: make udc_class a static const structure
USB: roles: make role_class a static const structure
dt-bindings: usb: dwc3: Add interrupt-names property support for wakeup interrupt
dt-bindings: usb: Add StarFive JH7110 USB controller
dt-bindings: usb: dwc3: Add IPQ9574 compatible
usb: cdns2: Fix spelling mistake in a trace message "Wakupe" -> "Wakeup"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
New Device Support:
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
New Functionality:
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
Fix-ups:
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
Bug Fixes:
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues"
* tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (53 commits)
leds: leds-mt6323: Adjust return/parameter types in wled get/set callbacks
leds: sgm3140: Add richtek,rt5033-led compatible
dt-bindings: leds: sgm3140: Document richtek,rt5033 compatible
dt-bindings: backlight: kinetic,ktz8866: Add missing type for "current-num-sinks"
dt-bindings: leds: Drop unneeded quotes
leds: Fix config reference for AW200xx driver
leds: leds-mt6323: Add support for WLEDs and MT6332
leds: leds-mt6323: Add support for MT6331 leds
leds: leds-mt6323: Open code and drop MT6323_CAL_HW_DUTY macro
leds: leds-mt6323: Drop MT6323_ prefix from macros and defines
leds: leds-mt6323: Specify registers and specs in platform data
dt-bindings: leds: leds-mt6323: Document mt6332 compatible
dt-bindings: leds: leds-mt6323: Document mt6331 compatible
leds: simatic-ipc-leds-gpio: Introduce more Kconfig switches
leds: simatic-ipc-leds-gpio: Split up into multiple drivers
leds: simatic-ipc-leds-gpio: Move two extra gpio pins into another table
leds: simatic-ipc-leds-gpio: Add terminating entries to gpio tables
leds: flash: leds-qcom-flash: Fix an unsigned comparison which can never be negative
leds: cht-wcove: Remove unneeded semicolon
leds: cht-wcove: Fix an unsigned comparison which can never be negative
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- I2C has now a co-maintainer taking care of the host drivers. Welcome
Andi Shyti and have fun!
- platform remove callback converted to return void in drivers
- simplify drivers by using devm_clk_get_enabled()
- introduce i2c_get_match_data() to avoid more boilerplate code
(especially since the core stopped delivering an i2c_device_id)
- and the usual bunch of driver updates
* tag 'i2c-for-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: uniphier: Use devm_clk_get_enabled()
i2c: uniphier-f: Use devm_clk_get_enabled()
i2c: owl: Use devm_clk_get_enabled()
i2c: lpc2k: Use devm_clk_get_enabled()
i2c: hix5hd2: Use devm_clk_get_enabled()
i2c: sun6i-p2wi: Use devm_clk_get_enabled()
i2c: pasemi-platform: Use devm_clk_get_enabled()
i2c: mt7621: Use devm_clk_get_enabled()
i2c: xiic: Use devm_clk_get_enabled()
i2c: davinci: Use platform table macro over module_alias
i2c: ocores: use devm_ managed clks
i2c: nomadik: Use dev_err_probe() whenever possible
i2c: nomadik: Use devm_clk_get_enabled()
i2c: nomadik: Remove unnecessary goto label
usb: typec: ucsi: Mark dGPUs as DEVICE scope
i2c: wmt: Use devm_platform_get_and_ioremap_resource()
i2c: versatile: Use devm_platform_get_and_ioremap_resource()
i2c: hix5hd2: Add I2C_M_STOP flag support for i2c-hix5hd2 driver.
i2c: mpc: Use of_property_read_reg() to parse "reg"
i2c: imx-lpi2c: Don't open-code DIV_ROUND_UP
...
|
|
Pull ARM SoC updates from Arnd Bergmann:
"These are mostly minor cleanups and bugfixes that address harmless
problems.
The largest branch is a conversion of the omap platform to use GPIO
descriptors throughout the tree, for any devices that are not fully
converted to devicetree.
The Samsung Exynos platform gains back support for the Exynos4212 chip
that was previously unused and removed but is now used for the Samsung
Galaxy Tab3"
* tag 'soc-arm-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
ARM: omap2: Fix copy/paste bug
MAINTAINERS: Replace my email address
Input: ads7846 - fix pointer cast warning
Input: ads7846 - Fix usage of match data
ARM: omap2: Fix checkpatch issues
arm: omap1: replace printk() with pr_err macro
ARM: omap: Fix checkpatch issues
ARM: s3c: Switch i2c drivers back to use .probe()
ARM: versatile: mark mmc_status() static
ARM: spear: include "pl080.h" for pl080_get_signal() prototype
ARM: sa1100: address missing prototype warnings
ARM: pxa: fix missing-prototypes warnings
ARM: orion5x: fix d2net gpio initialization
ARM: omap2: fix missing tick_broadcast() prototype
ARM: omap1: add missing include
ARM: lpc32xx: add missing include
ARM: imx: add missing include
ARM: highbank: add missing include
ARM: ep93xx: fix missing-prototype warnings
ARM: davinci: fix davinci_cpufreq_init() declaration
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have two new drivers, some improvements to the core code, lots of
different updates to existing GPIO drivers and some dt-bindings on
top.
There's nothing controversial in here and almost everything has been
in next for more than a week (95% a lot longer than this). The only
thing that has spent less time in next is a new driver so no risk of
regressions.
The single merge pulls in changes that remove all usage of global GPIO
numbers from arch/arm/mach-omap.
Core GPIO library:
- remove unused symbols
- don't spam the kernel log with messages about hogs
- remove old sysfs API cruft
- improve handling of GPIO masks
New drivers:
- add a driver for the BlueField-3 GPIO controller
- add GPIO support for the TPS65219 PMIC
Driver improvements:
- extend the gpio-aggregator driver to support ramp-up/ramp-down
delay
- remove unnecessary CONFIG_OF guards from gpio-aggregator
- readability improvements in gpio-tangier
- switch i2c drivers back to using probe() now that it's been
converted in the i2c subsystem to not taking the id parameter
- remove unused inclusions of of_gpio.h in several drivers
- make pm ops static in gpio-davinci and fix a comment
- use more devres in drivers to shrink and simplify the code
- add missing include in gpio-sa1100
- add HAS_IOPORT KConfig dependency where needed
- add permissions checks before accessing pins in gpio-tegra186
- convert the gpio-zynq driver to using immutable irqchips
- preserve output settings set by the bootloader in gpio-mpc8xxx
Selftests:
- tweak the variable naming in script tests
Device tree updates:
- convert gpio-mmio and gpio-stmpe to YAML
- add parsing of GPIO hogs to gpio-vf610
- add bindings for the Cirrus EP93xx GPIO controller
- add gpio-line-names property to the gpio-pca9570 bindings
- extend the binding for x-powers,axp209 with another block"
* tag 'gpio-updates-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (58 commits)
of: unittest: drop assertions for GPIO hog messages
gpiolib: Drop unused domain_ops memeber of GPIO IRQ chip
gpio: synq: remove unused zynq_gpio_irq_reqres/zynq_gpio_irq_relres
dt-bindings: gpio: gpio-vf610: Add parsing of hogs
gpio: lpc18xx: Remove unused of_gpio.h inclusion
gpio: xra1403: Remove unused of_gpio.h inclusion
gpio: mpc8xxx: Remove unused of_gpio.h inclusion
dt-bindings: gpio: Add Cirrus EP93xx
gpio: mpc8xxx: latch GPIOs state on module load when configured as output
selftests: gpio: gpio-sim: Use same variable name for sysfs pathname
gpio: mlxbf3: Add gpio driver support
gpio: delay: Remove duplicative functionality
gpio: aggregator: Set up a parser of delay line parameters
gpio: aggregator: Support delay for setting up individual GPIOs
gpio: aggregator: Remove CONFIG_OF and of_match_ptr() protections
dt-bindings: gpio: pca9570: add gpio-line-names property
gpiolib: remove unused gpio_cansleep()
gpio: tps65219: add GPIO support for TPS65219 PMIC
gpio: zynq: fix zynqmp_gpio not an immutable chip warning
gpio: davinci: make davinci_gpio_dev_pm_ops static
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm updates from Andrew Morton:
- Yosry Ahmed brought back some cgroup v1 stats in OOM logs
- Yosry has also eliminated cgroup's atomic rstat flushing
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning
- Lorenzo Stoakes has done some maintanance work on the
get_user_pages() interface
- Liam Howlett continues with cleanups and maintenance work to the
maple tree code. Peng Zhang also does some work on maple tree
- Johannes Weiner has done some cleanup work on the compaction code
- David Hildenbrand has contributed additional selftests for
get_user_pages()
- Thomas Gleixner has contributed some maintenance and optimization
work for the vmalloc code
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting
- Christoph Hellwig has some cleanups for the filemap/directio code
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the
provided APIs rather than open-coding accesses
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings
- John Hubbard has a series of fixes to the MM selftesting code
- ZhangPeng continues the folio conversion campaign
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment
from 128 to 8
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code
- Vishal Moola also has done some folio conversion work
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch
* tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (380 commits)
mm/hugetlb: remove hugetlb_set_page_subpool()
mm: nommu: correct the range of mmap_sem_read_lock in task_mem()
hugetlb: revert use of page_cache_next_miss()
Revert "page cache: fix page_cache_next/prev_miss off by one"
mm/vmscan: fix root proactive reclaim unthrottling unbalanced node
mm: memcg: rename and document global_reclaim()
mm: kill [add|del]_page_to_lru_list()
mm: compaction: convert to use a folio in isolate_migratepages_block()
mm: zswap: fix double invalidate with exclusive loads
mm: remove unnecessary pagevec includes
mm: remove references to pagevec
mm: rename invalidate_mapping_pagevec to mapping_try_invalidate
mm: remove struct pagevec
net: convert sunrpc from pagevec to folio_batch
i915: convert i915_gpu_error to use a folio_batch
pagevec: rename fbatch_count()
mm: remove check_move_unevictable_pages()
drm: convert drm_gem_put_pages() to use a folio_batch
i915: convert shmem_sg_free_table() to use a folio_batch
scatterlist: add sg_set_folio()
...
|
