| Age | Commit message (Collapse) | Author |
|---|
|
The value '0' is duplicated with USB_DIR_OUT
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200623031001.8469-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The line-speed algorithm clamps the requested value to the supported
range instead of bailing out on unsupported values.
Provide min and max macros and indicate how they are derived instead of
hardcoding the limits.
Note that the algorithm depends on the minimum rate (45.78 bps)
being rounded up (and the maximum rate being rounded down) to avoid
special casing.
Suggested-by: Michael Hanselmann <public@hansmi.ch>
Link: https://lore.kernel.org/r/20200630095756.GZ3334@localhost
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add constants for the prescaler and divisor registers. Document and
name register 0x25, and put the LCR define to more use.
The 0x25 register (CH341_REG_LCR2) is only used by CH341 chips before
version 0x30 and is involved in configuring the line control parameters.
It's not known to the author whether there any such chips in the wild,
and Linux' ch341 driver never supported them. For chip version 0x30 and
above the 0x25 register is always set to zero. The alternative would've
been to not set the register at all, but that may have unintended
effects.
Signed-off-by: Michael Hanselmann <public@hansmi.ch>
Link: https://lore.kernel.org/r/2e80916d-1be8-dc0f-abf9-adc0feea1803@msgid.hansmi.ch
[ johan: fix up comment ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
We want the USB fixes in here, and this resolves a merge issue found in
linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.8-rc3 to resolve some reported
issues.
Nothing major here:
- gadget driver fixes
- cdns3 driver fixes
- xhci fixes
- renesas_usbhs driver fixes
- some new device support with ids
- documentation update
All of these have been in linux-next with no reported issues"
* tag 'usb-5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (27 commits)
usb: renesas_usbhs: getting residue from callback_result
Revert "usb: dwc3: exynos: Add support for Exynos5422 suspend clk"
xhci: Poll for U0 after disabling USB2 LPM
xhci: Return if xHCI doesn't support LPM
usb: host: xhci-mtk: avoid runtime suspend when removing hcd
xhci: Fix enumeration issue when setting max packet size for FS devices.
xhci: Fix incorrect EP_STATE_MASK
usb: cdns3: ep0: add spinlock for cdns3_check_new_setup
usb: cdns3: trace: using correct dir value
usb: cdns3: ep0: fix the test mode set incorrectly
Revert "usb: dwc3: exynos: Add support for Exynos5422 suspend clk"
usb: gadget: udc: Potential Oops in error handling code
usb: phy: tegra: Fix unnecessary check in tegra_usb_phy_probe()
usb: dwc3: pci: Fix reference count leak in dwc3_pci_resume_work
usb: cdns3: ep0: add spinlock for cdns3_check_new_setup
usb: cdns3: trace: using correct dir value
usb: cdns3: ep0: fix the test mode set incorrectly
usb: typec: tcpci_rt1711h: avoid screaming irq causing boot hangs
USB: ohci-sm501: Add missed iounmap() in remove
cdc-acm: Add DISABLE_ECHO quirk for Microchip/SMSC chip
...
|
|
trace_printk should not be used in production code, replace it
call with dev_dbg.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20200627070307.516803-2-drinkcat@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v5.8-rc2
A revert of Exynos5422 suspend clock support, it turns out it wasn't
ready to be merged. CDNS3 got a fix for test mode initialization.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'fixes-for-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
Revert "usb: dwc3: exynos: Add support for Exynos5422 suspend clk"
usb: gadget: udc: Potential Oops in error handling code
usb: phy: tegra: Fix unnecessary check in tegra_usb_phy_probe()
usb: dwc3: pci: Fix reference count leak in dwc3_pci_resume_work
usb: cdns3: ep0: add spinlock for cdns3_check_new_setup
usb: cdns3: trace: using correct dir value
usb: cdns3: ep0: fix the test mode set incorrectly
|
|
In kgdb context, calling console handlers aren't safe due to locks used
in those handlers which could in turn lead to a deadlock. Although, using
oops_in_progress increases the chance to bypass locks in most console
handlers but it might not be sufficient enough in case a console uses
more locks (VT/TTY is good example).
Currently when a driver provides both polling I/O and a console then kdb
will output using the console. We can increase robustness by using the
currently active polling I/O driver (which should be lockless) instead
of the corresponding console. For several common cases (e.g. an
embedded system with a single serial port that is used both for console
output and debugger I/O) this will result in no console handler being
used.
In order to achieve this we need to reverse the order of preference to
use dbg_io_ops (uses polling I/O mode) over console APIs. So we just
store "struct console" that represents debugger I/O in dbg_io_ops and
while emitting kdb messages, skip console that matches dbg_io_ops
console in order to avoid duplicate messages. After this change,
"is_console" param becomes redundant and hence removed.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1591264879-25920-5-git-send-email-sumit.garg@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
This driver assumed that dmaengine_tx_status() could return
the residue even if the transfer was completed. However,
this was not correct usage [1] and this caused to break getting
the residue after the commit 24461d9792c2 ("dmaengine:
virt-dma: Fix access after free in vchan_complete()") actually.
So, this is possible to get wrong received size if the usb
controller gets a short packet. For example, g_zero driver
causes "bad OUT byte" errors.
The usb-dmac driver will support the callback_result, so this
driver can use it to get residue correctly. Note that even if
the usb-dmac driver has not supported the callback_result yet,
this patch doesn't cause any side-effects.
[1]
https://lore.kernel.org/dmaengine/20200616165550.GP2324254@vkoul-mobl/
Reported-by: Hien Dang <hien.dang.eb@renesas.com>
Fixes: 24461d9792c2 ("dmaengine: virt-dma: Fix access after free in vchan_complete()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1592482277-19563-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We defined macros for all the magic constants in the previous patch. So
let us use the macro in the code now.
No functional change intended.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Acked-by: Helge Deller <deller@gmx.de>
Link: https://lore.kernel.org/r/20200615074910.19267-26-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code currently uses bitfields to store true-false values. Switch all
of that to bools. Apart from the cleanup, it saves 20B of code as many
shifts, ANDs, and ORs became simple movzb's.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce names (en enum) for 0, 1, and 2 constants. We now have
VCI_HALF_BRIGHT, VCI_NORMAL, and VCI_BOLD instead.
Apart from the cleanup,
1) the enum allows for better type checking, and
2) this saves some code. No more fiddling with bits is needed in
assembly now. (OTOH, the structure is larger.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 07f6842341abe978e6375078f84506ec3280ece5.
Since SCLK_SCLK_USBD300 suspend clock need to be configured
for phy module, I wrongly mapped this clock to DWC3 code.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 07f6842341ab ("usb: dwc3: exynos: Add support for Exynos5422 suspend clk")
Link: https://lore.kernel.org/r/20200623074637.756-1-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB2 devices with LPM enabled may interrupt the system suspend:
[ 932.510475] usb 1-7: usb suspend, wakeup 0
[ 932.510549] hub 1-0:1.0: hub_suspend
[ 932.510581] usb usb1: bus suspend, wakeup 0
[ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended
[ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended
..
[ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03
..
[ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
[ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
[ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16
During system suspend, USB core will let HC suspends the device if it
doesn't have remote wakeup enabled and doesn't have any children.
However, from the log above we can see that the usb 1-7 doesn't get bus
suspended due to not in U0. After a while the port finished U2 -> U0
transition, interrupts the suspend process.
The observation is that after disabling LPM, port doesn't transit to U0
immediately and can linger in U2. xHCI spec 4.23.5.2 states that the
maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for
the affected device is advertised as 400us, which is still not enough
based on my testing result.
So let's use the maximum permitted latency, 10000, to poll for U0
status to solve the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Just return if xHCI is quirked to disable LPM. We can save some time
from reading registers and doing spinlocks.
Add stable tag as we want this patch together with the next one,
"Poll for U0 after disabling USB2 LPM" which fixes a suspend issue
for some USB2 LPM devices
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When runtime suspend was enabled, runtime suspend might happen
when xhci is removing hcd. This might cause kernel panic when hcd
has been freed but runtime pm suspend related handle need to
reference it.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unable to complete the enumeration of a USB TV Tuner device.
Per XHCI spec (4.6.5), the EP state field of the input context shall
be cleared for a set address command. In the special case of an FS
device that has "MaxPacketSize0 = 8", the Linux XHCI driver does
not do this before evaluating the context. With an XHCI controller
that checks the EP state field for parameter context error this
causes a problem in cases such as the device getting reset again
after enumeration.
When that field is cleared, the problem does not occur.
This was found and fixed by Sasi Kumar.
Cc: stable@vger.kernel.org
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
EP_STATE_MASK should be 0x7 instead of 0xf
xhci spec 6.2.3 shows that the EP state field in the endpoint context data
structure consist of bits [2:0].
The old value included a bit from the next field which fortunately is a
RsvdZ region. So hopefully this hasn't caused too much harm
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The other thread may access other endpoints when the cdns3_check_new_setup
is handling, add spinlock to protect it.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 'tmode' is ctrl->wIndex, changing it as the real test
mode value for register assignment.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jun Li <jun.li@nxp.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For some reason, the TEST_ defines in the usb/ch9.h files did not have
the USB_ prefix on it, making it a bit confusing when reading the file,
as well as not the nicest thing to do in a uapi file.
So fix that up and add the USB_ prefix on to them, and fix up all
in-kernel usages. This included deleting the duplicate copy in the
net2272.h file.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jules Irenge <jbi.octave@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: Rob Gill <rrobgill@protonmail.com>
Cc: Macpaul Lin <macpaul.lin@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Bin Liu <b-liu@ti.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200618144206.2655890-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 07f6842341abe978e6375078f84506ec3280ece5.
Since SCLK_SCLK_USBD300 suspend clock need to be configured
for phy module, I wrongly mapped this clock to DWC3 code.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
If this is in "transceiver" mode the the ->qwork isn't required and is
a NULL pointer. This can lead to a NULL dereference when we call
destroy_workqueue(udc->qwork).
Fixes: 3517c31a8ece ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
In the function tegra_usb_phy_probe(), if usb_add_phy_dev() failed,
the return value will be given to err, and if usb_add_phy_dev() succeed,
the return value will be zero. Thus it is unnecessary to repeated check
here.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
dwc3_pci_resume_work() calls pm_runtime_get_sync() that increments
the reference counter. In case of failure, decrement the reference
before returning.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
The other thread may access other endpoints when the cdns3_check_new_setup
is handling, add spinlock to protect it.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
The 'tmode' is ctrl->wIndex, changing it as the real test
mode value for register assignment.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
The IR Droid / IR Toy device used custom protocol over serial
line, so it is presenting itself as CDC ACM device.
Now that we have proper in-kernel driver for it we need to black-list the
device in cdc-acm driver.
http://dangerousprototypes.com/docs/USB_Infrared_Toy
https://www.irdroid.com/irdroid-usb-ir-transceiver/
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add PID for CH340 that's found on some ESP8266 dev boards made by
LilyGO. The specific device that contains such serial converter can be
seen here: https://github.com/LilyGO/LILYGO-T-OI.
Apparently, it's a regular CH340, but I've confirmed with others that
also bought this board that the PID found on this device (0x7522)
differs from other devices with the "same" converter (0x7523).
Simply adding its PID to the driver and rebuilding it made it work
as expected.
Signed-off-by: Igor Moura <imphilippini@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add USB IDs for GosunCn GM500 series cellular modules.
RNDIS config:
usb-devices
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 12 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=305a ProdID=1404 Rev=03.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
MBIM config:
usb-devices
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=305a ProdID=1405 Rev=03.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
ECM config:
usb-devices
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 13 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=305a ProdID=1406 Rev=03.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#=0x4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This is a UPB (Universal Powerline Bus) PIM (Powerline Interface Module)
which allows for controlling multiple UPB compatible devices from Linux
using the standard serial interface.
Based on vendor application source code there are two different models
of USB based PIM devices in addition to a number of RS232 based PIM's.
The vendor UPB application source contains the following USB ID's:
#define USB_PCS_VENDOR_ID 0x04b4
#define USB_PCS_PIM_PRODUCT_ID 0x5500
#define USB_SAI_VENDOR_ID 0x17dd
#define USB_SAI_PIM_PRODUCT_ID 0x5500
The first set of ID's correspond to the PIM variant sold by Powerline
Control Systems while the second corresponds to the Simply Automated
Incorporated PIM. As the product ID for both of these match the default
cypress HID->COM RS232 product ID it assumed that they both use an
internal variant of this HID->COM RS232 converter hardware. However
as the vendor ID for the Simply Automated variant is different we need
to also add it to the cypress_M8 driver so that it is properly
detected.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Link: https://lore.kernel.org/r/20200616220403.1807003-1-james.hilliard1@gmail.com
Cc: stable@vger.kernel.org
[ johan: amend VID define entry ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Rename the list of specific devices that an OTG device could support to
make it more obvious as to what this list is for and what it is doing.
Also rename the configuration option to make it more obvious as well.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: "Diego Elio Pettenò" <flameeyes@flameeyes.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Qi Zhou <atmgnd@outlook.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Cc: Harry Pan <harry.pan@intel.com>
Cc: David Heinzelmann <heinzelmann.david@gmail.com>
Cc: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200618094300.1887727-9-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix up the wording in a comment for the scsi driver saying what it does
using better terminology.
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200618094300.1887727-8-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make it obvious that the UAS driver is being ignored for a specific
device by fixing up the wording to be more clear.
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200618094300.1887727-7-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sierra driver had two different functions for trying to determine
different quirks that did the same exact thing. Remove one and rename
things to make it more obvious exactly what the different lists do.
Cc: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200618094300.1887727-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Better describe what is happening with a list of devices that are being
ignored by the driver.
Cc: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200618094300.1887727-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This comment has been present since the start of git. Since no one is
going to do anything about it, and all seems to work well, just drop the
thing entirely.
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200618094300.1887727-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB OTG code has the ability to disable external hubs, but the
configuration option for it is oddly named. Rename it to be more
obvious as to what it does.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Bin Liu <b-liu@ti.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: David Heinzelmann <heinzelmann.david@gmail.com>
Cc: "Lee, Chiasheng" <chiasheng.lee@intel.com>
Cc: Keiya Nobuta <nobuta.keiya@fujitsu.com>
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20200618094300.1887727-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB core has a quirk flag to ignore specific endpoints, so rename it
to be more obvious what this quirk does.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Richard Dodd <richard.o.dodd@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cox <jonathan@jdcox.net>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: "Thiébaud Weksteen" <tweek@google.com>
Cc: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200618094300.1887727-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace hardcoded maximum USB string length (126 bytes) by definition
"USB_MAX_STRING_LEN".
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1592471618-29428-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are two spelling mistakes in the Kconfig text. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200618093224.10179-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
John reported screaming irq caused by rt1711h when system boot[1],
this is because irq request is done before tcpci_register_port(),
so the chip->tcpci has not been setup, irq handler is entered but
can't do anything, this patch is to address this by moving the irq
request after tcpci_register_port().
[1] https://lore.kernel.org/linux-usb/20200530040157.31038-1-john.stultz@linaro.org
Fixes: ce08eaeb6388 ("staging: typec: rt1711h typec chip driver")
Cc: stable <stable@vger.kernel.org> # v4.18+
Cc: John Stultz <john.stultz@linaro.org>
Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20200604112118.38062-1-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver misses calling iounmap() in remove to undo the ioremap()
called in probe.
Add the missed call to fix it.
Fixes: f54aab6ebcec ("usb: ohci-sm501 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200610024844.3628408-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB_DEVICE(0x0424, 0x274e) can send data before cdc_acm is ready,
causing garbage chars on the TTY causing stray input to the shell
and/or login prompt.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200605105418.22263-1-joakim.tjernlund@infinera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A Synopsys USB2.0 core used in Huawei Kunpeng920 SoC has a bug which
might cause the host controller not issuing ping.
Bug description:
After indicating an Interrupt on Async Advance, the software uses the
doorbell mechanism to delete the Next Link queue head of the last
executed queue head. At this time, the host controller still references
the removed queue head(the queue head is NULL). NULL reference causes
the host controller to lose the USB device.
Solution:
After deleting the Next Link queue head, when has_synopsys_hc_bug set
to 1，the software can write one of the valid queue head addresses to
the ASYNCLISTADDR register to allow the host controller to get
the valid queue head. in order to solve that problem, this patch set
the flag for Huawei Kunpeng920
There are detailed instructions and solutions in this patch:
commit 2f7ac6c19997 ("USB: ehci: add workaround for Synopsys HC bug")
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1591588019-44284-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
BUG: memory leak
unreferenced object 0xffff888055046e00 (size 256):
comm "kworker/2:9", pid 2570, jiffies 4294942129 (age 1095.500s)
hex dump (first 32 bytes):
00 70 04 55 80 88 ff ff 18 bb 5a 81 ff ff ff ff .p.U......Z.....
f5 96 78 81 ff ff ff ff 37 de 8e 81 ff ff ff ff ..x.....7.......
backtrace:
[<00000000d121dccf>] kmemleak_alloc_recursive
include/linux/kmemleak.h:43 [inline]
[<00000000d121dccf>] slab_post_alloc_hook mm/slab.h:586 [inline]
[<00000000d121dccf>] slab_alloc_node mm/slub.c:2786 [inline]
[<00000000d121dccf>] slab_alloc mm/slub.c:2794 [inline]
[<00000000d121dccf>] kmem_cache_alloc_trace+0x15e/0x2d0 mm/slub.c:2811
[<000000005c3c3381>] kmalloc include/linux/slab.h:555 [inline]
[<000000005c3c3381>] usbtest_probe+0x286/0x19d0
drivers/usb/misc/usbtest.c:2790
[<000000001cec6910>] usb_probe_interface+0x2bd/0x870
drivers/usb/core/driver.c:361
[<000000007806c118>] really_probe+0x48d/0x8f0 drivers/base/dd.c:551
[<00000000a3308c3e>] driver_probe_device+0xfc/0x2a0 drivers/base/dd.c:724
[<000000003ef66004>] __device_attach_driver+0x1b6/0x240
drivers/base/dd.c:831
[<00000000eee53e97>] bus_for_each_drv+0x14e/0x1e0 drivers/base/bus.c:431
[<00000000bb0648d0>] __device_attach+0x1f9/0x350 drivers/base/dd.c:897
[<00000000838b324a>] device_initial_probe+0x1a/0x20 drivers/base/dd.c:944
[<0000000030d501c1>] bus_probe_device+0x1e1/0x280 drivers/base/bus.c:491
[<000000005bd7adef>] device_add+0x131d/0x1c40 drivers/base/core.c:2504
[<00000000a0937814>] usb_set_configuration+0xe84/0x1ab0
drivers/usb/core/message.c:2030
[<00000000e3934741>] generic_probe+0x6a/0xe0 drivers/usb/core/generic.c:210
[<0000000098ade0f1>] usb_probe_device+0x90/0xd0
drivers/usb/core/driver.c:266
[<000000007806c118>] really_probe+0x48d/0x8f0 drivers/base/dd.c:551
[<00000000a3308c3e>] driver_probe_device+0xfc/0x2a0 drivers/base/dd.c:724
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Link: https://lore.kernel.org/r/20200612035210.20494-1-qiang.zhang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During dwc2 driver probe, after gadget registration to the udc class
driver, if exist any builtin function driver it immediately bound to
dwc2 and after init host side (dwc2_hcd_init()) stucked in host mode.
Patch postpone gadget registration after host side initialization done.
Fixes: 117777b2c3bb9 ("usb: dwc2: Move gadget probe function into platform code")
Reported-by: kbuild test robot <lkp@intel.com>
Tested-by: Marek Vasut <marex@denx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/f21cb38fecc72a230b86155d94c7e60c9cb66f58.1591690938.git.hminas@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Logitech C922, just like other Logitech webcams,
needs the USB_QUIRK_DELAY_INIT or it will randomly
not respond after device connection
Signed-off-by: Tomasz Meresiński <tomasz@meresinski.eu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200603203347.7792-1-tomasz@meresinski.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
