| Age | Commit message (Collapse) | Author |
|---|
|
When using more than one Event Ring segment (ERSTSZ > 1), software shall
set the DESI bits in the ERDP register to the number of the segment to
which the upper ERDP bits are pointing. The xHC may use the DESI bits
as a shortcut to determine whether it needs to check for an Event Ring
Full condition: If it's enqueueing events in a different segment, it
need not compare its internal Enqueue Pointer with the Dequeue Pointer
in the upper bits of the ERDP register (sec 5.5.2.3.3).
Not setting the DESI bits correctly can result in the xHC enqueueing
events past the Dequeue Pointer. On Renesas uPD720201 host controllers,
incorrect DESI bits cause an interrupt storm. For comparison, VIA VL805
host controllers do not exhibit such problems. Perhaps they do not take
advantage of the optimization afforded by the DESI bits.
To fix the issue, assign the segment number to each struct xhci_segment
in xhci_segment_alloc(). When advancing the Dequeue Pointer in
xhci_update_erst_dequeue(), write the segment number to the DESI bits.
On driver probe, set the DESI bits to zero in xhci_set_hc_event_deq() as
processing starts in segment 0. Likewise on driver teardown, clear the
DESI bits to zero in xhci_free_interrupter() when clearing the upper
bits of the ERDP register. Previously those functions (incorrectly)
treated the DESI bits as if they're declared RsvdP.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The next_trb() helper relies on a link TRB at the end of a ring segment
to know a segment ends. This works well with transfer rings that use
link trbs, but not with event rings.
Event rings segments are always filled by host to segment size
before moving to next segment. It does not use link TRBs
Check for both link trb and full segment in next_trb() helper to
support event rings.
Useful if several interrupters with several event rings are supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With several xhci controllers active at the same time its hard to
keep track of ports without knowing bus number
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want to trace other port structure members than just port number
so pass entire port structure as parameter instead of just port number.
Dig the port number from the port structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.6-rc7
Here are some new modem device ids, including an entry needed for Sierra
EM9191 which stopped working with recent firmware.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.6-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom to DELL custom modem FM101R-GL
USB: serial: option: add entry for Sierra EM9191 with new firmware
USB: serial: option: add Telit LE910C4-WWX 0x1035 composition
|
|
Convert to using the new inode timestamp accessor functions.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20231004185347.80880-12-jlayton@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Convert to using the new inode timestamp accessor functions.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20231004185347.80880-11-jlayton@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Convert to using the new inode timestamp accessor functions.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20231004185347.80880-10-jlayton@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
The Type-C port drivers can make PM related decisions based
on is the device USB3 or USB2.
Suggested-by: Benson Leung <bleung@chromium.org>
Tested-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231011105825.320062-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding functions that USB hub code can use to inform the
Type-C class about connected USB devices.
Once taken into use, it will allow the Type-C port drivers
to power off components that are not needed, for example if
USB2 device is enumerated, everything that is only relevant
for USB3 (retimers, etc.), can be powered off.
This will also create a symlink "typec" for the USB devices
pointing to the USB Type-C partner device.
Suggested-by: Benson Leung <bleung@chromium.org>
Tested-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231011105825.320062-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
.data of platform_device_info will be copied into .platform_data of
struct device via platform_device_add_data.
However, vhcis[i] contains a spinlock, is dynamically allocated and
used by other code, so it is not meant to be copied. The workaround
was to use void *vhci as an agent, but it was removed in the commit
suggested below.
This patch adds back the workaround and changes the way of using
platform_data accordingly.
Reported-by: syzbot+e0dbc33630a092ccf033@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/00000000000029242706077f3145@google.com/
Reported-by: syzbot+6867a9777f4b8dc4e256@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/0000000000007634c1060793197c@google.com/
Fixes: b8aaf639b403 ("usbip: Use platform_device_register_full()")
Tested-by: syzbot+6867a9777f4b8dc4e256@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/0000000000007ac87d0607979b6b@google.com/
Signed-off-by: Hongren Zheng <i@zenithal.me>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/ZSpHPCaQ5DDA9Ysl@Sun
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB and Thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update the USB serial option driver support for the Fibocom
FM101R-GL LTE modules as there are actually several different variants.
- VID:PID 413C:8213, FM101R-GL are laptop M.2 cards (with
MBIM interfaces for Linux)
- VID:PID 413C:8215, FM101R-GL ESIM are laptop M.2 cards (with
MBIM interface for Linux)
0x8213: mbim, tty
0x8215: mbim, tty
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=413c ProdID=8213 Rev= 5.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=Fibocom FM101-GL Module
S: SerialNumber=a3b7cbf0
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=896mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=413c ProdID=8215 Rev= 5.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=Fibocom FM101-GL Module
S: SerialNumber=a3b7cbf0
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=896mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Puliang Lu <puliang.lu@fibocom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In some cases, like with multiple LUN targets or where the target has to
respond to transport level requests from the receiving context it can be
better to defer cmd submission to a helper thread. If the backend driver
blocks on something like request/tag allocation it can block the entire
target submission path and other LUs and transport IO on that session.
In other cases like single LUN targets with storage that can support all
the commands that the target can queue, then it's best to submit the cmd
to the backend from the target's cmd receiving context.
Subsequent commits will allow the user to config what they prefer, but
drivers like loop can't directly submit because they can be called from a
context that can't sleep. And, drivers like vhost-scsi can support direct
submission, but need to keep their default behavior of deferring execution
to avoid possible regressions where the backend can block.
Make the drivers tell LIO core if they support direct submissions and their
current default, so we can prevent users from misconfiguring the system and
initialize devices correctly.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230928020907.5730-2-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Following a firmware update of the modem, the interface for the AT
command port changed, so add it back.
T: Bus=08 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=1199 ProdID=90d3 Rev=00.06
S: Manufacturer=Sierra Wireless, Incorporated
S: Product=Sierra Wireless EM9191
S: SerialNumber=xxxxxxxxxxxxxxxx
C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
Signed-off-by: Benoît Monin <benoit.monin@gmx.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add support for the following Telit LE910C4-WWX composition:
0x1035: TTY, TTY, ECM
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1035 Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=e1b117c7
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I: If#= 3 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In some implementations, such as the Qualcomm platforms, the display
driver has no way to query the current HPD state and as such it's
impossible to distinguish between disconnect and attention events.
Add a parameter to drm_connector_oob_hotplug_event() to pass the HPD
state.
Also push the test for unchanged state in the displayport altmode driver
into the i915 driver, to allow other drivers to act upon each update.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009174048.2695981-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009174048.2695981-2-dmitry.baryshkov@linaro.org
|
|
On some OEM systems, adding a W7900 dGPU triggers RAS errors and hangs
at a black screen on startup. This issue occurs only if `ucsi_acpi` has
loaded before `amdgpu` has loaded. The reason for this failure is that
`amdgpu` uses power_supply_is_system_supplied() to determine if running
on AC or DC power at startup. If this value is reported incorrectly the
dGPU will also be programmed incorrectly and trigger errors.
power_supply_is_system_supplied() reports the wrong value because UCSI
power supplies provided as part of the system don't properly report the
scope as "DEVICE" scope (not powering the system).
In order to fix this issue check the capabilities reported from the UCSI
power supply to ensure that it supports charging a battery and that it can
be powered by AC. Mark the scope accordingly.
Cc: stable@vger.kernel.org
Fixes: a7fbfd44c020 ("usb: typec: ucsi: Mark dGPUs as DEVICE scope")
Link: https://www.intel.com/content/www/us/en/products/docs/io/universal-serial-bus/usb-type-c-ucsi-spec.html p28
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009184643.129986-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The link between the partner device and its USB Power
Delivery instance was never removed which prevented the
device from being released. Removing the link always when
the partner is unregistered.
Fixes: b04e1747fbcc ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Cc: stable <stable@kernel.org>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Closes: https://lore.kernel.org/linux-usb/ZSUMXdw9nanHtnw2@kuha.fi.intel.com/
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231010141749.3912016-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Upon receiving an ACK for a sent EXIT_MODE message, the DisplayPort
driver currently resets the status and configuration of the port partner.
The hpd signal is not updated despite being part of the status, so the
Display stack can still transmit video despite typec_altmode_exit placing
the lanes in a Safe State.
Set hpd to low when a sent EXIT_MODE message is ACK'ed.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009210057.3773877-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implements the USB part of Intel USB-I2C/GPIO/SPI adapter device
named "La Jolla Cove Adapter" (LJCA).
The communication between the various LJCA module drivers and the
hardware will be muxed/demuxed by this driver. Three modules (
I2C, GPIO, and SPI) are supported currently.
Each sub-module of LJCA device is identified by type field within
the LJCA message header.
The sub-modules of LJCA can use ljca_transfer() to issue a transfer
between host and hardware. And ljca_register_event_cb is exported
to LJCA sub-module drivers for hardware event subscription.
The minimum code in ASL that covers this board is
Scope (\_SB.PCI0.DWC3.RHUB.HS01)
{
Device (GPIO)
{
Name (_ADR, Zero)
Name (_STA, 0x0F)
}
Device (I2C)
{
Name (_ADR, One)
Name (_STA, 0x0F)
}
Device (SPI)
{
Name (_ADR, 0x02)
Name (_STA, 0x0F)
}
}
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/1696833205-16716-2-git-send-email-wentong.wu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tps25750 status register is a subset of tps6598x status register, hence
a trace for tps25750 status register is added.
Signed-off-by: Abdel Alkuor <abdelalkuor@geotab.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231003155842.57313-10-alkuor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tps25750 power status register is a subset of tps6598x power status
register.
Signed-off-by: Abdel Alkuor <abdelalkuor@geotab.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231003155842.57313-9-alkuor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tps25750 event1 register doesn't have all bits in tps6598x
event registers, only show the events that are masked
Signed-off-by: Abdel Alkuor <abdelalkuor@geotab.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231003155842.57313-8-alkuor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TPS25750 controller requires a binary to be loaded with a configuration
binary by an EEPROM or a host.
Appling a patch bundling using a host is implemented based on the flow
diagram pg.62 in TPS25750 host interface manual.
https://www.ti.com/lit/ug/slvuc05a/slvuc05a.pdf
The flow diagram can be summarized as following:
- Start the patch loading sequence with patch bundle information by
executing PBMs
- Write the whole patch at once
- When writing the patch fails, execute PBMe which instructs the PD controller
to end the patching process
- After writing the patch successfully, execute PBMc which verifies the patch
integrity and applies the patch internally
- Wait for the device to switch into APP mode (normal operation)
The execuation flow diagram polls the events register and then polls the
corresponding register related to the event as well before advancing to the next
state. Polling the events register is a redundant step, in this implementation
only the corresponding register related to the event is polled.
Adding tps25750 support, the followings are being taken care of:
- Implement applying patch flow.
- When an EEPROM is present, tps25750 loads the binary configuration from
EEPROM. Hence, all we need to do is wait for the device to switch to APP
mode.
- Dead battery flag is cleared after switching tps25750 to APP mode so the
PD controller becomes fully functional.
- Add port registration as tps25750 doesn't have system configuration register
to get dr/pr of the current applied binary configuration. Get data role from
the device node and power role from PD status register.
- tps25750 event registers structure is different than tps6598x's,
tps25750 has 11 bytes of events which are read at once where
tps6598x has two event registers of 8 bytes each which are read
separately. Likewise MASK event registers. Also, not all events
are supported in both devices. Create a new handler to accommodate
tps25750 interrupt.
- Enable sleep mode so the device enters sleep state when idling.
- When the current mode is PTCH, enable tps25750 by loading a
configuration patch that switches the device into APP mode.
- Add resume and suspend pm for tps25750.
Signed-off-by: Abdel Alkuor <abdelalkuor@geotab.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231003155842.57313-7-alkuor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Part of tps6598x refactoring, we need to move the following functions
to device data as tps25750 has different implementation than tps6598x
and cd321x:
- interrupt handler
- port registration
- power status trace
- status trace
Signed-off-by: Abdel Alkuor <abdelalkuor@geotab.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231003155842.57313-6-alkuor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tps6598x and cd321x use TPS_REG_SYSTEM_CONF to get dr/pr roles
where other similar devices don't have this register such as tps25750.
Move tps6598x port registration to its own function
Signed-off-by: Abdel Alkuor <abdelalkuor@geotab.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231003155842.57313-5-alkuor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TPS25750 has a patch mode indicating the device requires
a configuration to get the device into operational mode
Signed-off-by: Abdel Alkuor <abdelalkuor@geotab.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231003155842.57313-4-alkuor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some commands in tps25750 take longer than 1 second
to complete, and some responses need some delay before
the result becomes available.
Signed-off-by: Abdel Alkuor <abdelalkuor@geotab.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231003155842.57313-3-alkuor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231009211356.3242037-16-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree.
Add of.h which is implicitly included by of_platform.h.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231009211356.3242037-17-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch replaces the usage of netif_stop_queue with netif_device_detach
in the u_ether driver. The netif_device_detach function not only stops all
tx queues by calling netif_tx_stop_all_queues but also marks the device as
removed by clearing the __LINK_STATE_PRESENT bit.
This change helps notify user space about the disconnection of the device
more effectively, compared to netif_stop_queue, which only stops a single
transmit queue.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20231006155646.12938-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "len" here is sometimes negative error codes from
usb_get_descriptor(), so we don't want to type promote them to unsigned
long.
This bug pre-dates the invention of git.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/506f7935-2cba-41d9-ab5d-ddb6ad6320bd@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code to create the child platform device is essentially the same as
what platform_device_register_full() does, so change over to use
that same function to reduce duplication.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231006164312.3528524-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a hub is disconnected that has device(s) that's attached to the usbip layer
the disconnect function might fail because it tries to release the port
on an already disconnected hub.
Fixes: 6080cd0e9239 ("staging: usbip: claim ports used by shared devices")
Signed-off-by: Jonas Blixt <jonas.blixt@actia.se>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230615092810.1215490-1-jonas.blixt@actia.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 3a63f86c6a6cb0601f0563a81574745da2979e3b.
Based on review comments, it was applied too soon and needs more work.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231005081716.GA13853@pendragon.ideasonboard.com
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 52a39f2cf62bb5430ad1f54cd522dbfdab1d71ba.
Based on review comments, it was applied too soon and needs more work.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231005081716.GA13853@pendragon.ideasonboard.com
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit bb00788bd62778ef80a97d67a0e3c569ac6be06f.
Based on review comments, it was applied too soon and needs more work.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231005081716.GA13853@pendragon.ideasonboard.com
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On SM8550, the non-altmode orientation is not given anymore within
altmode events, even with USB SVIDs events.
On the other side, the Type-C connector orientation is correctly
reported by a signal from the PMIC.
Take this gpio signal when we detect some Type-C port activity
to notify any Type-C switches tied to the Type-C port connectors.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231002-topic-sm8550-upstream-type-c-orientation-v2-2-125410d3ff95@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Avoid a kernel-doc warning by documenting it:
drivers/usb/dwc3/core.h:1343: warning:
Function parameter or member 'gfladj_refclk_lpm_sel'
not described in 'dwc3'
Fixes: a6fc2f1b0927 ("usb: dwc3: core: add gfladj_refclk_lpm_sel quirk")
Signed-off-by: Swarup Laxman Kotiaklapudi <swarupkotikalapudi@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231002210137.209382-1-swarupkotikalapudi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add "c_terminal_type" and "p_terminal_type" configfs entries
in order to allow the user to change the capture and playback terminal
type codes.
These fields affect the type of audio device that Windows detects, so
being able to modify this is useful when it would be advantageous for
a gadget to be detected as something other than a generic
speaker/microphone.
The fields default to microphone for the capture type field and speaker
for the playback type field as was the case before.
Signed-off-by: James Gruber <jimmyjgruber@gmail.com>
Link: https://lore.kernel.org/r/20230914222746.155126-1-jimmyjgruber@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a kthread_stop_put() helper that stops a thread and puts its task
struct. Use it to replace the various instances of kthread_stop()
followed by put_task_struct().
Remove the kthread_stop_put() macro in usbip that is similar but doesn't
return the result of kthread_stop().
[agruenba@redhat.com: fix kerneldoc comment]
Link: https://lkml.kernel.org/r/20230911111730.2565537-1-agruenba@redhat.com
[akpm@linux-foundation.org: document kthread_stop_put()'s argument]
Link: https://lkml.kernel.org/r/20230907234048.2499820-1-agruenba@redhat.com
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct f_midi.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: John Keeping <john@keeping.me.uk>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Hulk Robot <hulkci@huawei.com>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: Will McVicker <willmcvicker@google.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Zhang Qilong <zhangqilong3@huawei.com>
Cc: linux-usb@vger.kernel.org
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915195938.never.611-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct ffs_buffer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: John Keeping <john@keeping.me.uk>
Cc: Udipto Goswami <quic_ugoswami@quicinc.com>
Cc: Linyu Yuan <quic_linyyuan@quicinc.com>
Cc: linux-usb@vger.kernel.org
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915195849.never.275-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct urb_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20230915195812.never.371-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
If, for any reason, the open-coded arithmetic causes a wraparound,
the protection that `struct_size()` adds against potential integer
overflows is defeated. Fix this by hardening call to `struct_size()`
with `size_add()`.
Fixes: b626871a7cda ("usb: atm: Use struct_size() helper")
Signed-off-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/ZQSuboEIhvATAdxN@work
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Return USB_GADGET_DELAYED_STATUS from the setup() callback for 0-length
transfers as a workaround to stop some UDC drivers (e.g. dwc3) from
automatically proceeding with the status stage.
This workaround should be removed once all UDC drivers are fixed to
always delay the status stage until a response is queued to EP0.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/a8d2b91f9890dc21daa359183e84879ff4525180.1693237258.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Return USB_GADGET_DELAYED_STATUS from the setup() callback for 0-length
transfers as a workaround to stop some UDC drivers (e.g. dwc3) from
automatically proceeding with the status stage.
This workaround should be removed once all UDC drivers are fixed to
always delay the status stage until a response is queued to EP0.
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/c56077322f0d3fc6d504092a266cb89d75701087.1693237258.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e9b29ffc519b ("USB: add Cypress c67x00 OTG controller HCD driver")
declared but never implemented this.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20230825091518.22180-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exposing the value of the field as is.
The Peak Current value has to be interpreted as described
in Table 6-10 (Fixed Power Source Peak Current Capability)
of the USB Power Delivery Specification, but that
interpretation will be done in user space, not in kernel.
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231002142240.2641962-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
