| Age | Commit message (Collapse) | Author |
|---|
|
This integrates the PHY wrapper into the core hcd infrastructure.
Multiple PHYs which are part of the HCD's device tree node are now
managed (= powered on/off when needed), by the new usb_phy_roothub code.
Suspend and resume is also supported, however not for
runtime/auto-suspend (which is triggered for example when no devices are
connected to the USB bus). This is needed on some SoCs (for example
Amlogic Meson GXL) because if the PHYs are disabled during auto-suspend
then devices which are plugged in afterwards are not seen by the host.
One example where this is required is the Amlogic GXL and GXM SoCs:
They are using a dwc3 USB controller with up to three ports enabled on
the internal roothub. Each port has it's own PHY which must be enabled
(if one of the PHYs is left disabled then none of the USB ports works at
all).
The new logic works on the Amlogic GXL and GXM SoCs because the dwc3
driver internally creates a xhci-hcd which then registers a HCD which
then triggers our new PHY wrapper.
USB controller drivers can opt out of this by setting
"skip_phy_initialization" in struct usb_hcd to true. This is identical
to how it works for a single USB PHY, so the "multiple PHY" handling is
disabled for drivers that opted out of the management logic of a single
PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many SoC platforms have separate devices for the USB PHY which are
registered through the generic PHY framework. These PHYs have to be
enabled to make the USB controller actually work. They also have to be
disabled again on shutdown/suspend.
Currently (at least) the following HCI platform drivers are using custom
code to obtain all PHYs via devicetree for the roothub/controller and
disable/enable them when required:
- ehci-platform.c has ehci_platform_power_{on,off}
- xhci-mtk.c has xhci_mtk_phy_{init,exit,power_on,power_off}
- ohci-platform.c has ohci_platform_power_{on,off}
With this new wrapper the USB PHYs can be specified directly in the
USB controller's devicetree node (just like on the drivers listed
above). This allows SoCs like the Amlogic Meson GXL family to operate
correctly once this is wired up correctly. These SoCs use a dwc3
controller and require all USB PHYs to be initialized (if one of the USB
PHYs it not initialized then none of USB port works at all).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB HCD core driver parses the device-tree node for "phys" and
"usb-phys" properties. It also manages the power state of these PHYs
automatically.
However, drivers may opt-out of this behavior by setting "phy" or
"usb_phy" in struct usb_hcd to a non-null value. An example where this
is required is the "Qualcomm USB2 controller", implemented by the
chipidea driver. The hardware requires that the PHY is only powered on
after the "reset completed" event from the controller is received.
A follow-up patch will allow the USB HCD core driver to manage more than
one PHY. Add a new "skip_phy_initialization" bitflag to struct usb_hcd
so drivers can opt-out of any PHY management provided by the USB HCD
core driver.
This also updates the existing drivers so they use the new flag if they
want to opt out of the PHY management provided by the USB HCD core
driver. This means that for these drivers the new "multiple PHY"
handling (which will be added in a follow-up patch) will be disabled as
well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use kasprintf instead of combination of kmalloc and sprintf and
therefore avoid unnecessary computation of string length.
Also, remove the useless local variable.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ACPI spec inserts sections for new features frequently and section
numbers are changed. It is easy to refer to ACPI spec if ACPI version
is available in comments.
There are no functional changes.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Disabing Latency Tolerance Messaging before port reset is unnecessary.
LTM is automatically disabled at port reset.
If host can't communicate with the device the LTM message will fail, and
the hub driver will unnecessarily do a logical disconnect.
Broken communication is ofter the reason for a reset in the first place.
Additionally we can't guarantee device is in a configured state,
epecially in reset-resume case when root hub lost power.
LTM can't be modified unless device is in a configured state.
Just remove LTM disabling before port reset.
Details about LTM and port reset in USB 3 specification:
USB 3 spec section 9.4.5
"The LTM Enable field can be modified by the SetFeature() and
ClearFeature() requests using the LTM_ENABLE feature selector.
This field is reset to zero when the device is reset."
USB 3 spec section 9.4.1
"The device shall process a Clear Feature (U1_Enable or U2_Enable or
LTM_Enable) only if the device is in the configured state."
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add waiting for an URB transmit finish that let the last URB to be sent
(to be not discarded) during 'release' procedure. W/o this waiting,the
last frame will be nearly always lost.
A test case: an attempt of sending a single frame:
echo -en "\001mk255" >/dev/adutux0
Signed-off-by: Kirill Kapranov <kirill.kirillovich.kapranov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pointer dev is initialized and then re-assigned with the same value
a little later, hence the second assignment is redundant and can be
removed.
Cleans up clang warning:
drivers/usb/wusbcore/wa-nep.c:88:17: warning: Value stored to 'dev'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that usbip supports USB3, the maximum number of ports allowed
on a hub is 15 (USB_SS_MAXPORTS), not 31 (USB_MAXCHILDREN).
Reported-by: Gianluigi Tiesi <sherpya@netfarm.it>
Reported-by: Borissh1983 <borissh1983@gmail.com>
References: https://bugs.debian.org/878866
Fixes: 1c9de5bf4286 ("usbip: vhci-hcd: Add USB3 SuperSpeed support")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel would like to have all stack VLA usage removed[1]. We
already have a pre-processor constant defined MAX_SGLEN. We can use
this instead of the variable param-sglen.
[1]: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch reverts the commit 835e4241e714 ("usb: host: xhci-plat:
enable clk in resume timing") because this driver also has runtime PM
and the commit 560869100b99 ("clk: renesas: cpg-mssr: Restore module
clocks during resume") will restore the clock on R-Car H3 environment.
If the xhci_plat_suspend() disables the clk, the system cannot enable
the clk in resume like the following behavior:
< In resume >
- genpd_resume_noirq() runs and enable the clk (enable_count = 1)
- cpg_mssr_resume_noirq() restores the clk register.
-- Since the clk was disabled in suspend, cpg_mssr_resume_noirq()
will disable the clk and keep the enable_count.
- Even if xhci_plat_resume() calls clk_prepare_enable(), since
the enable_count is 1, the clk will be not enabled.
After this patch is applied, the cpg-mssr driver will save the clk
as enable, so the clk will be enabled in resume.
Fixes: 835e4241e714 ("usb: host: xhci-plat: enable clk in resume timing")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change fixes buffer overflows and silent data corruption with the
usbmon device driver text file read operations.
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for r8a77965 (R-Car M3-N).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This USB-SATA controller seems to be similar with JMicron bridge
152d:2566 already on the list. Adding it here fixes "Invalid
field in cdb" errors.
Signed-off-by: Teijo Kinnunen <teijo.kinnunen@code-q.fi>
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xHCI DbC implementation might enter a deadlock situation because
there is no sufficient protection against the shared data between
process and softirq contexts. This can lead to the following lockdep
warnings. This patch changes to use spin_{,un}lock_irq{save,restore}
to avoid potential deadlock.
[ 528.248084] ================================
[ 528.252914] WARNING: inconsistent lock state
[ 528.257756] 4.15.0-rc1+ #1630 Not tainted
[ 528.262305] --------------------------------
[ 528.267145] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 528.273953] ksoftirqd/1/17 [HC0[0]:SC1[1]:HE0:SE0] takes:
[ 528.280075] (&(&port->port_lock)->rlock){+.?.}, at: [<ffffffff815396a8>] dbc_rx_push+0x38/0x1c0
[ 528.290043] {SOFTIRQ-ON-W} state was registered at:
[ 528.295570] _raw_spin_lock+0x2f/0x40
[ 528.299818] dbc_write_complete+0x27/0xa0
[ 528.304458] xhci_dbc_giveback+0xd1/0x200
[ 528.309098] xhci_dbc_flush_endpoint_requests+0x50/0x70
[ 528.315116] xhci_dbc_handle_events+0x696/0x7b0
[ 528.320349] process_one_work+0x1ee/0x6e0
[ 528.324988] worker_thread+0x4a/0x430
[ 528.329236] kthread+0x13e/0x170
[ 528.332992] ret_from_fork+0x24/0x30
[ 528.337141] irq event stamp: 2861
[ 528.340897] hardirqs last enabled at (2860): [<ffffffff810674ea>] tasklet_action+0x6a/0x250
[ 528.350460] hardirqs last disabled at (2861): [<ffffffff817dc1ef>] _raw_spin_lock_irq+0xf/0x40
[ 528.360219] softirqs last enabled at (2852): [<ffffffff817e0e8c>] __do_softirq+0x3dc/0x4f9
[ 528.369683] softirqs last disabled at (2857): [<ffffffff8106805b>] run_ksoftirqd+0x1b/0x60
[ 528.379048]
[ 528.379048] other info that might help us debug this:
[ 528.386443] Possible unsafe locking scenario:
[ 528.386443]
[ 528.393150] CPU0
[ 528.395917] ----
[ 528.398687] lock(&(&port->port_lock)->rlock);
[ 528.403821] <Interrupt>
[ 528.406786] lock(&(&port->port_lock)->rlock);
[ 528.412116]
[ 528.412116] *** DEADLOCK ***
[ 528.412116]
[ 528.418825] no locks held by ksoftirqd/1/17.
[ 528.423662]
[ 528.423662] stack backtrace:
[ 528.428598] CPU: 1 PID: 17 Comm: ksoftirqd/1 Not tainted 4.15.0-rc1+ #1630
[ 528.436387] Call Trace:
[ 528.439158] dump_stack+0x5e/0x8e
[ 528.442914] print_usage_bug+0x1fc/0x220
[ 528.447357] mark_lock+0x4db/0x5a0
[ 528.451210] __lock_acquire+0x726/0x1130
[ 528.455655] ? __lock_acquire+0x557/0x1130
[ 528.460296] lock_acquire+0xa2/0x200
[ 528.464347] ? dbc_rx_push+0x38/0x1c0
[ 528.468496] _raw_spin_lock_irq+0x35/0x40
[ 528.473038] ? dbc_rx_push+0x38/0x1c0
[ 528.477186] dbc_rx_push+0x38/0x1c0
[ 528.481139] tasklet_action+0x1d2/0x250
[ 528.485483] __do_softirq+0x1dc/0x4f9
[ 528.489630] run_ksoftirqd+0x1b/0x60
[ 528.493682] smpboot_thread_fn+0x179/0x270
[ 528.498324] kthread+0x13e/0x170
[ 528.501981] ? sort_range+0x20/0x20
[ 528.505933] ? kthread_delayed_work_timer_fn+0x80/0x80
[ 528.511755] ret_from_fork+0x24/0x30
Fixes: dfba2174dc42 ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix incorrent values showed for max Primary stream and
Linear stream array (LSA) values in the endpoint context
decoder.
Fixes: 19a7d0d65c4a ("usb: host: xhci: add Slot and EP Context tracers")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.16-rc4
Just small fixes now. The two most important are a fix for a a lock up
on USB ID pin change during system suspend/resume on dwc3 and a
use-after-free fix in ffs_fs_kill_sb().
Apart from that, some DT compatible fixes.
|
|
When the host wants to fetch OS descriptors, it sends two requests. The
first is only for the header and the second for the full amount
specified by the header in the first request. The OS descriptor handling
code is distinguishing the header-only requests based on the wLength of
the setup packet, but the same code is executed in both cases to
construct the actual header. Simplify this by always constructing the
header and then filling out the rest of the request if the wLength is
greater than the size of the header.
Also remove the duplicate code for queueing the request to ep0 by adding
a goto label.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When handling an OS descriptor request, one of the first operations is
to zero out the request buffer using the wLength from the setup packet.
There is no bounds checking, so a wLength > 4096 would clobber memory
adjacent to the request buffer. Fix this by taking the min of wLength
and the request buffer length prior to the memset. While at it, define
the buffer length in a header file so that magic numbers don't appear
throughout the code.
When returning data to the host, the data length should be the min of
the wLength and the valid data we have to return. Currently we are
returning wLength, thus requests for a wLength greater than the amount
of data in the OS descriptor buffer would return invalid (albeit zero'd)
data following the valid descriptor data. Fix this by counting the
number of bytes when constructing the data and using this when
determining the length of the request.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The irq is available in hsotg already, so there's no need to pass it as
separate function parameter.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
As devm_ioremap_resource() checks for valid resource,
make use of it instead of testing ourselves. As a bonus
memory region is requested.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Pointer tv_nexus is being initialized a value and this is never read
and is later being updated with the same value. Remove the redundant
initialization so that the assignment to tv_nexus is performed later
and more local to when it is being read.
Cleans up clang warning:
drivers/usb/gadget/function/f_tcm.c:1097:25: warning: Value stored to
'tv_nexus' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The local variable event is of type enum usb_phy_events. Use
the same enum value USB_EVENT_NONE instead of UX500_MUSB_NONE.
This avoids a warning when building with clang:
drivers/usb/phy/phy-ab8500-usb.c:906:30: warning: implicit conversion from
enumeration type 'enum ux500_musb_vbus_id_status' to different enumeration
type 'enum usb_phy_events' [-Wenum-conversion]
enum usb_phy_events event = UX500_MUSB_NONE;
~~~~~ ^~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
mxs_charger_secondary_detection() is only used in this file, so make
it static.
This fixes the following sparse warning:
drivers/usb/phy/phy-mxs-usb.c:581:23: warning: symbol 'mxs_charger_secondary_detection' was not declared. Should it be static?
Acked-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Use dma_pool_zalloc instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
kill_pid_info_as_cred and security_task_kill
commit d178bc3a708f39cbfefc3fab37032d3f2511b4ec ("user namespace: usb:
make usb urbs user namespace aware (v2)") changed kill_pid_info_as_uid
to kill_pid_info_as_cred, saving and passing a cred structure instead of
uids. Since the secid can be obtained from the cred, drop the secid fields
from the usb_dev_state and async structures, and drop the secid argument to
kill_pid_info_as_cred. Replace the secid argument to security_task_kill
with the cred. Update SELinux, Smack, and AppArmor to use the cred, which
avoids the need for Smack and AppArmor to use a secid at all in this hook.
Further changes to Smack might still be required to take full advantage of
this change, since it should now be possible to perform capability
checking based on the supplied cred. The changes to Smack and AppArmor
have only been compile-tested.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
Delete a misleading comment to an obvious definition.
Signed-off-by: Kirill Kapranov <kirill.kirillovich.kapranov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
GPL v2 is the original license according to the old license text.
See f64cdd0e94f1faf3b7f2b03af71f70dc6d8da0c2.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 57e6f0d7b804 ("typec: tcpm: Only request matching pdos") is causing
a regression, before this commit e.g. the GPD win and GPD pocket devices
were charging at 9V 3A with a PD charger, now they are instead slowly
discharging at 5V 0.4A, as this commit causes the ports max_snk_mv/ma/mw
settings to be completely ignored.
Arguably the way to fix this would be to add a PDO_VAR() describing the
voltage range to the snk_caps of boards which can handle any voltage in
their range, but the "typec: tcpm: Only request matching pdos" commit
looks at the type of PDO advertised by the source/charger and if that
is fixed (as it typically is) only compairs against PDO_FIXED entries
in the snk_caps so supporting a range of voltage would require adding a
PDO_FIXED entry for *every possible* voltage to snk_caps.
AFAICT there is no reason why a fixed source_cap cannot be matched against
a variable snk_cap, so at a minimum the commit should be rewritten to
support that.
For now lets revert the "typec: tcpm: Only request matching pdos" commit,
fixing the regression.
Fixes: 57e6f0d7b804 ("typec: tcpm: Only request matching pdos")
Cc: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Without pm_runtime_{get,put}_sync calls in place, reading
vbus status via /sys causes the following error:
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
pgd = b333e822
[fa0ab060] *pgd=48011452(bad)
[<c05261b0>] (musb_default_readb) from [<c0525bd0>] (musb_vbus_show+0x58/0xe4)
[<c0525bd0>] (musb_vbus_show) from [<c04c0148>] (dev_attr_show+0x20/0x44)
[<c04c0148>] (dev_attr_show) from [<c0259f74>] (sysfs_kf_seq_show+0x80/0xdc)
[<c0259f74>] (sysfs_kf_seq_show) from [<c0210bac>] (seq_read+0x250/0x448)
[<c0210bac>] (seq_read) from [<c01edb40>] (__vfs_read+0x1c/0x118)
[<c01edb40>] (__vfs_read) from [<c01edccc>] (vfs_read+0x90/0x144)
[<c01edccc>] (vfs_read) from [<c01ee1d0>] (SyS_read+0x3c/0x74)
[<c01ee1d0>] (SyS_read) from [<c0106fe0>] (ret_fast_syscall+0x0/0x54)
Solution was suggested by Tony Lindgren <tony@atomide.com>.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
