| Age | Commit message (Collapse) | Author |
|---|
|
When plugging in a USB webcam I see the following message:
xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs
XHCI_TRUST_TX_LENGTH quirk?
handle_tx_event: 913 callbacks suppressed
All is quiet again with this patch (and I've done a fair but of soak
testing with the camera since).
Cc: <stable@vger.kernel.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Trying to read from debugfs after the system has resumed from
hibernate causes a use-after-free and thus a protection fault.
Steps to reproduce:
Hibernate system, resume from hibernate, then run
$ cat /sys/kernel/debug/usb/xhci/*/command-ring/enqueue
[ 3902.765086] general protection fault: 0000 [#1] PREEMPT SMP
...
[ 3902.765136] RIP: 0010:xhci_trb_virt_to_dma.part.50+0x5/0x30
...
[ 3902.765178] Call Trace:
[ 3902.765188] xhci_ring_enqueue_show+0x1e/0x40
[ 3902.765197] seq_read+0xdb/0x3a0
[ 3902.765204] ? __handle_mm_fault+0x5fb/0x1210
[ 3902.765211] full_proxy_read+0x4a/0x70
[ 3902.765219] __vfs_read+0x23/0x120
[ 3902.765228] vfs_read+0x8e/0x130
[ 3902.765235] SyS_read+0x42/0x90
[ 3902.765242] do_syscall_64+0x6b/0x290
[ 3902.765251] entry_SYSCALL64_slow_path+0x25/0x25
The issue is caused by the xhci ring structures being reallocated
when the system is resumed, but pointers to the old structures
being retained in the debugfs files "private" field:
The proposed patch fixes this issue by storing a pointer to the xhci_ring
field in the xhci device structure in debugfs rather than directly
storing a pointer to the xhci_ring.
Fixes: 02b6fdc2a153 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Free the virt_device and its debugfs_private member together.
When resuming from hibernate the .free_dev callback unconditionally
freed the debugfs_private member, but could leave virt_device intact.
This triggered a NULL pointer dereference after resume when usbmuxd
sent a USBDEVFS_SETCONFIGURATION ioctl to a device, trying to add a
endpoint debugfs entry to a already freed debugfs_private pointer.
Fixes: 02b6fdc2a153 ("usb: xhci: Add debugfs interface for xHCI driver")
Reported-by: Alexander Kappner <agk@godking.net>
Tested-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes
USB-serial fixes for v4.15-rc6
Here are some new device ids for ftdi_sio, option and qcserial.
Note that the qcserial patch enables the SetControlLineState request
(used to raise DTR/RTS) for the GPS interface of all devices using the
Sierra Wireless layout. This was required for the Sierra Wireless EM7565
and has been tested using several other modems as well.
All but the final commit have been in linux-next without any reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add AIRBUS_DS_P8GR device IDs to ftdi_sio driver.
Signed-off-by: Max Schulze <max.schulze@posteo.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
USB Ethernet gadget now works on Tegra30.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One fix for ulpi-node lookup at msm glue driver
|
|
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
There is one more model that has the same issue - C925e, so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This modem needs this quirk to operate. It produces timeouts when
resumed without reset.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the following static checker warnings:
The patch c6688ef9f297: "usbip: fix stub_rx: harden CMD_SUBMIT path
to handle malicious input" from Dec 7, 2017, leads to the following
static checker warning:
drivers/usb/usbip/stub_rx.c:346 get_pipe()
warn: impossible condition
'(pdu->u.cmd_submit.transfer_buffer_length > ((~0 >> 1))) =>
(s32min-s32max > s32max)'
drivers/usb/usbip/stub_rx.c:486 stub_recv_cmd_submit()
warn: always true condition
'(pdu->u.cmd_submit.transfer_buffer_length <= ((~0 >> 1))) =>
(s32min-s32max <= s32max)'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usbip driver is leaking socket pointer address in messages. Remove
the messages that aren't useful and print sockfd in the ones that
are useful for debugging.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove and/or change debug, info. and error messages to not print
kernel pointer addresses.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove and/or change debug, info. and error messages to not print
kernel pointer addresses.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB 3.1 devices are not detected as 3.1 capable since 4.15-rc3 due to a
off by one in commit 81cf4a45360f ("USB: core: Add type-specific length
check of BOS descriptors")
It uses USB_DT_USB_SSP_CAP_SIZE() to get SSP capability size which takes
the zero based SSAC as argument, not the actual count of sublink speed
attributes.
USB3 spec 9.6.2.5 says "The number of Sublink Speed Attributes = SSAC + 1."
The type-specific length check patch was added to stable and needs to be
fixed there as well
Fixes: 81cf4a45360f ("USB: core: Add type-specific length check of BOS descriptors")
Cc: linux-stable <stable@vger.kernel.org>
CC: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for YUGA CLM920-NC5 PID 0x9625 USB modem to option
driver.
Interface layout:
0: QCDM/DIAG
1: ADB
2: MODEM
3: AT
4: RMNET
Signed-off-by: Taiyi Wu <taiyity.wu@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clear Feature Endpoint Halt should reset the data toggle even if the
endpoint isn't halted. Host should manage to clear the host side data
toggle to keep in sync with the device.
Test by sending a "3 data packet URB" before and after clearing the halt.
this should create a toggle sequence with two consecutive DATA0 packets.
A successful test sequence looks like this
ClearFeature(ENDPOINT_HALT) - initial toggle clear
DATA0 (max packet sized)
DATA1 (max packet sized)
DATA0 (zero length packet)
ClearFeature(ENDPOINT_HALT) - resets toggle
DATA0 (max packet sized), if clear halt fails then toggle is DATA1
DATA1 (max packet sized)
DATA0 (zero length packet)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB SS and SSP hubs provide wHubDelay values on their hub descriptor
which we should inform the USB Device about.
The USB Specification 3.0 explains, on section 9.4.11, how to
calculate the value and how to issue the request. Note that a
USB_REQ_SET_ISOCH_DELAY is valid on all device states (Default,
Address, Configured), we just *chose* to issue it from Address state
right after successfully fetching the USB Device Descriptor.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sierra Wireless EM7565 devices use the QCSERIAL_SWI layout for their
serial ports
T: Bus=01 Lev=03 Prnt=29 Port=01 Cnt=02 Dev#= 31 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1199 ProdID=9091 Rev= 0.06
S: Manufacturer=Sierra Wireless, Incorporated
S: Product=Sierra Wireless EM7565 Qualcomm Snapdragon X16 LTE-A
S: SerialNumber=xxxxxxxx
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=qcserial
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=qcserial
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
but need sendsetup = true for the NMEA port to make it work properly.
Simplify the patch compared to v1 as suggested by Bjørn Mork by taking
advantage of the fact that existing devices work with sendsetup = true
too.
Use sendsetup = true for the NMEA interface of QCSERIAL_SWI and add
DEVICE_SWI entries for the EM7565 PID 0x9091 and the EM7565 QDL PID
0x9090.
Tests with several MC73xx/MC74xx/MC77xx devices have been performed in
order to verify backward compatibility.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This patch adds support for PID 0x1101 of Telit ME910.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
According to drivers/usb/serial/io_edgeport.c, the driver may sleep
under a spinlock.
The function call path is:
edge_bulk_in_callback (acquire the spinlock)
process_rcvd_data
process_rcvd_status
change_port_settings
send_iosp_ext_cmd
write_cmd_usb
usb_kill_urb --> may sleep
To fix it, the redundant usb_kill_urb() is removed from the error path
after usb_submit_urb() fails.
This possible bug is found by my static analysis tool (DSAC) and checked
by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This patch adds extcon notifier callback to set the mode of
host/peripheral by using extcon state (e.g phy-rcar-gen3-usb2) for
non-otg channel (e.g. R-Car D3).
[Fengguang Wu: fixed sparse warning]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: renesas_usbhs: usbhs_rcar3_notifier() can be static
Fixes: 3a7cce26122e ("usb: renesas_usbhs: add extcon notifier to set mode for non-otg channel")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
A malicious USB device with crafted descriptors can cause the kernel
to access unallocated memory by setting the bNumInterfaces value too
high in a configuration descriptor. Although the value is adjusted
during parsing, this adjustment is skipped in one of the error return
paths.
This patch prevents the problem by setting bNumInterfaces to 0
initially. The existing code already sets it to the proper value
after parsing is complete.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 32fd87b3bbf5f7a045546401dfe2894dbbf4d8c3.
Alan wrote a better fix for this...
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usbhs_rcar3_power_and_pll_ctrl() will be used by non-otg channel
(e.g. R-Car D3) and the previous code has hardcoded as peripheral mode.
So, this patch sets the mode by using extcon state.
If the channel doesn't get any extcon devices, this driver's behavior
is the same as before.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
To cleanup the code, this patch adds a function to write the UGCTRL2
register.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
On rk3288-veyron devices on Chrome OS it was found that plugging in an
Arduino-based USB device could cause the system to lockup, especially
if the CPU Frequency was at one of the slower operating points (like
100 MHz / 200 MHz).
Upon tracing, I found that the following was happening:
* The USB device (full speed) was connected to a high speed hub and
then to the rk3288. Thus, we were dealing with split transactions,
which is all handled in software on dwc2.
* Userspace was initiating a BULK IN transfer
* When we sent the SSPLIT (to start the split transaction), we got an
ACK. Good. Then we issued the CSPLIT.
* When we sent the CSPLIT, we got back a NAK. We immediately (from
the interrupt handler) started to retry and sent another SSPLIT.
* The device kept NAKing our CSPLIT, so we kept ping-ponging between
sending a SSPLIT and a CSPLIT, each time sending from the interrupt
handler.
* The handling of the interrupts was (because of the low CPU speed and
the inefficiency of the dwc2 interrupt handler) was actually taking
_longer_ than it took the other side to send the ACK/NAK. Thus we
were _always_ in the USB interrupt routine.
* The fact that USB interrupts were always going off was preventing
other things from happening in the system. This included preventing
the system from being able to transition to a higher CPU frequency.
As I understand it, there is no requirement to retry super quickly
after a NAK, we just have to retry sometime in the future. Thus one
solution to the above is to just add a delay between getting a NAK and
retrying the transmission. If this delay is sufficiently long to get
out of the interrupt routine then the rest of the system will be able
to make forward progress. Even a 25 us delay would probably be
enough, but we'll be extra conservative and try to delay 1 ms (the
exact amount depends on HZ and the accuracy of the jiffy and how close
the current jiffy is to ticking, but could be as much as 20 ms or as
little as 1 ms).
Presumably adding a delay like this could impact the USB throughput,
so we only add the delay with repeated NAKs.
NOTE: Upon further testing of a pl2303 serial adapter, I found that
this fix may help with problems there. Specifically I found that the
pl2303 serial adapters tend to respond with a NAK when they have
nothing to say and thus we end with this same sequence.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
Note that the original premature free of the parent node has already
been fixed separately, but that fix was apparently never backported to
stable.
Fixes: 47654a162081 ("usb: chipidea: msm: Restore wrapper settings after reset")
Fixes: b74c43156c0c ("usb: chipidea: msm: ci_hdrc_msm_probe() missing of_node_get()")
Cc: stable <stable@vger.kernel.org> # 4.10: b74c43156c0c
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Function xhci_dbc_free_req is local to the source and does not need to
be in global scope, so make it static.
Cleans up sparse warning:
symbol 'xhci_dbc_free_req' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Incorrect size was given to memset when zeroing the DbC endpoint
structures on exit. Use element size * ARRAY_SIZE to fix it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: dfba2174dc42 ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The URB_NO_FSBR flag has never really been used. It was introduced as
a potential way for UHCI to minimize PCI bus usage (by not attempting
full-speed bulk and control transfers more than once per frame), but
the flag was not set by any drivers.
There's no point in keeping it around. This patch simplifies the API
by removing it. Unfortunately, it does have to be kept as part of the
usbfs ABI, but at least we can document in
include/uapi/linux/usbdevice_fs.h that it doesn't do anything.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB Power Delivery Specification (v3.0) dictates in ch.
6.4.1 - Capabilities Message - that the vSafe5V Fixed Supply
Object shall always be the first object. tcpm.c now checks
that this rule is obeyed (commit 5007e1b5db73 "typec: tcpm
Validate source and sink caps"), and that makes the
typec_wcove.c fail to probe. The voltage is higher then what
is permitted for the vSafe5V parameter.
Dropping the voltage in the first Fixed Supply object of the
sink capabilities down to 5V, and maximum current down to
500mA, making the driver probe successfully again.
Also, removing the Battery and Variable Supply objects, as
there is no need for them.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When cleaning up the configurations, make sure we only free the number
of configurations and interfaces that we could have allocated.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.15-rc4
We have a few fixes on dwc3:
- one fix which only happens with some implementations where we need to
wait longer for some commands to finish.
- Another fix for high-bandwidth isochronous endpoint programming making
sure that we send the correct DATA tokens in the correct sequence
- A couple PM fixes on dwc3-of-simple
The other synopsys controller driver (dwc2) got a fix for FIFO size
programming.
Other than these, we have a couple Kconfig fixes making sure that
dependencies are properly setup.
|
|
The dwc2 USB controller in Stratix10 has an additional ECC reset bit that
needs to get de-asserted in order for the controller to work properly.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
usbhs_pkt_pop()
This patch uses usbhs_pipe_clear_without_sequence() instead of
usbhsf_fifo_clear() because usbhsf_fifo_clear() may not clear the pipe
buffer completely. This patch also changes the clearing condition from
DMA only to both DMA and PIO.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds usbhs_pipe_clear_without_sequence() function.
The controller has the pipe buffer and the PIPEnCTR.ACLRM can clear
it completely. But, it's also clear the data sequence. So, the driver
needs to get the sequence before.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The datasheet doesn't mention that needs to poll of FRDY is set or not.
So, this patch removes such handling in the usbhsf_fifo_barrier().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Factor out the guts of usb charger initialization into usb_charger_init()
function, to make the usb_add_extcon() only do the extcon related things.
Meanwhile we also should initialize the USB charger before registering
the extcon device, in case the extcon notification was issued earlier than
usb charger initialization.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This reverts commit 7a9618a22aadffb55027d665491adf466bced61a.
Romain Izard recently reported that commit 7a9618a22aad ended up
allowing every legacy gadget driver to statically linked to the
kernel, however that doesn't work, since only one legacy gadget can be
bound to a controller. Because of that, let's revert the original commit
and fix the problem.
Reported-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Configuring the USB_G_WEBCAM driver as built-in leads to a link
error when CONFIG_VIDEO_V4L2 is a loadable module:
drivers/usb/gadget/function/f_uvc.o: In function `uvc_function_setup':
f_uvc.c:(.text+0xfe): undefined reference to `v4l2_event_queue'
drivers/usb/gadget/function/f_uvc.o: In function `uvc_function_ep0_complete':
f_uvc.c:(.text+0x188): undefined reference to `v4l2_event_queue'
This changes the Kconfig dependency to disallow that configuration,
and force it to be a module in that case as well.
This is apparently a rather old bug, but very hard to trigger
even in thousands of randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Some platforms (e.g. TI's DRA7 USB2 instance) have more trouble
with the metastability workaround as it supports only
a High-Speed PHY and the PHY can enter into an Erratic state [1]
when the controller is set in SuperSpeed mode as part of
the metastability workaround.
This causes upto 2 seconds delay in enumeration on DRA7's USB2
instance in gadget mode.
If these platforms can be better off without the workaround,
provide a device tree property to suggest that so the workaround
is avoided.
[1] Device mode enumeration trace showing PHY Erratic Error.
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event (00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The UDC core ensures that .udc_set_speed() is called with
a speed that is a minimum of the max speeds supported
by the gadget function driver and the UDC driver.
We can now use the speed argument as is.
Get rid of the debug print as that condition will never happen.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
There will never be a case when gadget.speed isn't already
USB_SPEED_FULL if connection is not USB-3 and gadget.speed
is not USB_SPEED_HIGH or USB_SPEED_LOW.
Remove the unnecessary code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add a jump target so that a specific error message is stored only once
at the end of this function implementation.
Replace two calls of the function "dev_err" by goto statements.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Variable is_short is set to zero but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed. Pointer dev is assigned a value that
is not read and it is updated a few statements later, this too is
redundant and can be removed. Cleans up clan warnings:
drivers/usb/gadget/udc/pxa27x_udc.c:986:3: warning: Value stored
to 'is_short' is never read
drivers/usb/gadget/udc/pxa27x_udc.c:1141:2: warning: Value stored
to 'dev' is never read
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Pointer udc is assigned but never read, hence it is redundant and
can be removed. Cleans up clang warning:
drivers/usb/gadget/udc/udc-xilinx.c:974:2: warning: Value stored
to 'udc' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The variable value is being assigned to zero but that value is never being
read. Either value is being reassigned in the following if condition, or
it is never read and the function returns. In both cases the assignment is
redundant and can be removed. Cleans up clang warning:
drivers/usb/gadget/legacy/inode.c:1473:4: warning: Value stored to 'value'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Trival fix to spelling mistake in ERR message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Silences the following warnings:
drivers/usb/gadget/function/f_fs.c:1253:37: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/gadget/function/f_fs.c:1253:37: expected void [noderef] <asn:1>*to
drivers/usb/gadget/function/f_fs.c:1253:37: got void *<noident>
drivers/usb/gadget/function/f_fs.c:2322:23: warning: cast to restricted __le32
drivers/usb/gadget/function/f_fs.c:2876:38: warning: cast to restricted __le32
drivers/usb/gadget/function/f_fs.c:272:12: warning: context imbalance in '__ffs_ep0_queue_wait' - unexpected unlock
drivers/usb/gadget/function/f_fs.c:450:17: warning: context imbalance in 'ffs_ep0_write' - different lock contexts for basic block
drivers/usb/gadget/function/f_fs.c:490:24: warning: context imbalance in '__ffs_ep0_read_events' - unexpected unlock
drivers/usb/gadget/function/f_fs.c:496:16: warning: context imbalance in 'ffs_ep0_read' - different lock contexts for basic block
Also, add an "unlocks spinlock" comment for consistency with existing ones.
No behaviour change is intended.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
