| Age | Commit message (Collapse) | Author |
|---|
|
The GPU PLL0 is not a fixed PLL and the rate can be set on it:
this is necessary especially on boards which bootloader is setting
a very low rate on this PLL before booting Linux, which would be
unsuitable for postdividing to reach the maximum allowed Adreno GPU
frequency of 710MHz (or, actually, even 670MHz..) on this SoC.
To allow setting rates on the GPU PLL0, also define VCO boundaries
and set the CLK_SET_RATE_PARENT flag to the GPU PLL0 postdivider.
With this change, the Adreno GPU is now able to scale through all
the available frequencies.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-12-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The GPU GX GDSC has GPU_GX_BCR reset and gfx3d_clk CXC, as stated
on downstream kernels (and as verified upstream, because otherwise
random lockups happen).
Also, add PWRSTS_RET and NO_RET_PERIPH: also as found downstream,
and also as verified here, to avoid GPU related lockups it is
necessary to force retain mem, but *not* peripheral when enabling
this GDSC (and, of course, the inverse on disablement).
With this change, the GPU finally works flawlessly on my four
different MSM8998 devices from two different manufacturers.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-11-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In some rare occasions, we want to only set the RETAIN_MEM bit, but
not the RETAIN_PERIPH one: this is seen on at least SDM630/636/660's
GPU-GX GDSC, where unsetting and setting back the RETAIN_PERIPH bit
will generate chaos and panics during GPU suspend time (mainly, the
chaos is unaligned access).
For this reason, introduce a new NO_RET_PERIPH flag to the GDSC
driver to address this corner case.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210113183817.447866-8-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This adds a basic driver for the MPLL block found in MStar/SigmaStar
ARMv7 SoCs.
Currently this driver is only good for calculating the rates of it's
outputs and the actual configuration must be done before the kernel
boots. Usually this is done even before u-boot starts.
This driver targets the MPLL block found in the MSC313/MSC313E but
there is no documentation this chip so the register descriptions for
the another MStar chip the MST786 were used as they seem to match.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210211052206.2955988-5-daniel@0x0f.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add a devm helper for clk_hw_register_fixed_factor() so that drivers that internally
register fixed factor clocks for things like dividers don't need to manually unregister
them on remove or if probe fails.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210211052206.2955988-4-daniel@0x0f.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED fix from Pavel Machek:
"One-liner fixing a build problem"
* 'for-rc8-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: rt8515: add V4L2_FLASH_LED_CLASS dependency
|
|
The leds-rt8515 driver can optionall use the v4l2 flash led class,
but it causes a link error when that class is in a loadable module
and the rt8515 driver itself is built-in:
ld.lld: error: undefined symbol: v4l2_flash_init
>>> referenced by leds-rt8515.c
>>> leds/flash/leds-rt8515.o:(rt8515_probe) in archive
drivers/built-in.a
Adding 'depends on V4L2_FLASH_LED_CLASS' in Kconfig would avoid that,
but it would make it impossible to use the driver without the
v4l2 support.
Add the same dependency that the other users of this class have
instead, which just prevents the broken configuration.
Fixes: e1c6edcbea13 ("leds: rt8515: Add Richtek RT8515 LED driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of IMX_INTMUX to ARCH_MXC,
and ask the user in case of compile-testing.
Fixes: 66968d7dfc3f5451 ("irqchip: Add COMPILE_TEST support for IMX_INTMUX")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210208145605.422943-1-geert+renesas@glider.be
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One small fix for the Allwinner clk driver so that display clks figure
out the correct rate to use.
This fixes displays running 4k@60Hz and some other resolutions that
haven't been exercised and fully understood until now"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: mp: fix parent rate change flag check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One fix for scsi_debug that fixes a memory leak on module removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_debug: Fix a memory leak
|
|
Writing one of key two values into the configuration key register
is a common operation, so a utility function has been added to
provide consistent behavior and eliminate code duplication.
Signed-off-by: Kevin P. Fleming <kevin+linux@km6g.us>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
To: linux-rtc@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615105113.57770-2-kevin+linux@km6g.us
|
|
Properly set flag WD_CD for rtc chips(pcf2129, pca2129)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201202031840.15582-1-biwen.li@oss.nxp.com
|
|
This patch fixes the following checkpatch.pl check:
CHECK: Alignment should match open parenthesis
Signed-off-by: Mukul Mehar <mukulmehar02@gmail.com>
Link: https://lore.kernel.org/r/20210213120556.73579-1-mukulmehar02@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixed the spelling of 'transfered' to 'transferred'.
Signed-off-by: Pritthijit Nath <pritthijit.nath@icloud.com>
Link: https://lore.kernel.org/r/20210212101324.12391-1-pritthijit.nath@icloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix sparse byte-order warnings in the i2400m_bm_cmd_prepare()
function:
wimax/i2400m/fw.c:194:36: warning: restricted __le32 degrades to integer
wimax/i2400m/fw.c:195:34: warning: invalid assignment: +=
wimax/i2400m/fw.c:195:34: left side has type unsigned int
wimax/i2400m/fw.c:195:34: right side has type restricted __le32
wimax/i2400m/fw.c:196:32: warning: restricted __le32 degrades to integer
wimax/i2400m/fw.c:196:47: warning: restricted __le32 degrades to integer
wimax/i2400m/fw.c:196:66: warning: restricted __le32 degrades to integer
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210212153843.8554-1-mail@anirudhrb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix some "incorrect type in assignment" warnings reported
by sparse in tx.c
sparse warnings:
wimax/i2400m/tx.c:788:35: warning: cast to restricted __le16
wimax/i2400m/tx.c:788:33: warning: incorrect type in assignment
(different base types)
wimax/i2400m/tx.c:788:33: expected restricted __le16 [usertype] num_pls
wimax/i2400m/tx.c:788:33: got unsigned short [usertype]
wimax/i2400m/tx.c:896:32: warning: cast to restricted __le32
wimax/i2400m/tx.c:896:30: warning: incorrect type in assignment
(different base types)
wimax/i2400m/tx.c:896:30: expected restricted __le32 [usertype] barker
wimax/i2400m/tx.c:896:30: got unsigned int [usertype]
wimax/i2400m/tx.c:897:34: warning: cast to restricted __le32
wimax/i2400m/tx.c:897:32: warning: incorrect type in assignment
(different base types)
wimax/i2400m/tx.c:897:32: expected restricted __le32 [usertype] sequence
wimax/i2400m/tx.c:897:32: got unsigned int [usertype]
wimax/i2400m/tx.c:899:15: warning: cast to restricted __le32
wimax/i2400m/tx.c:899:15: warning: cast from restricted __le16
Signed-off-by: Ayush <ayush@disroot.org>
Link: https://lore.kernel.org/r/20210212213628.801642-1-ayush@disroot.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
checkpatch warning fix for string split across lines
Signed-off-by: Manikantan Ravichandran <ravman1991@gmail.com>
Link: https://lore.kernel.org/r/20210212225035.GA16260@whach
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
memdup_user() is shorter and safer equivalent
of kmalloc/copy_from_user pair.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Link: https://lore.kernel.org/r/20210213120527.451531-1-insafonov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
_TO_DS_, _FROM_DS_, _MORE_FRAG_, _RETRY_, _PWRMGT_, _MORE_DATA_,
_PRIVACY_, _ORDER_ definitions are duplicate IEEE80211_FCTL_*
kernel definitions.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Link: https://lore.kernel.org/r/20210213131148.458582-1-insafonov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch removes some blank lines in order to fix a checkpatch issue.
Signed-off-by: William Durand <will+git@drnd.me>
Link: https://lore.kernel.org/r/20210213034711.14823-1-will+git@drnd.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The NXP PCA8565 is software compatible with the NXP PCF8563,
add DT and ACPI compatible entries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
To: linux-rtc@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210210220623.23233-1-marex@denx.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"One more I2C driver bugfix"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32f7: fix configuration of the digital filter
|
|
For non-QEBSM devices, get_buf_states() merges PENDING and EMPTY buffers
into a single group of finished buffers. To allow the upper-layer driver
to differentiate between the two states, qdio_check_pending() looks at
each buffer's state again and sets the sbal_state flag to
QDIO_OUTBUF_STATE_FLAG_PENDING accordingly.
So effectively we're spending overhead on _every_ Output Queue
inspection, just to avoid some additional TX completion calls in case
a group of buffers has completed with mixed EMPTY / PENDING state.
Given that PENDING buffers should rarely occur, this is a bad trade-off.
In particular so as the additional checks in get_buf_states() affect
_all_ device types (even those that don't use the PENDING state).
Rip it all out, and just report the PENDING completions separately as
we already do for QEBSM devices.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
For QEBSM devices the 'merge_pending' mechanism in get_buf_states()
doesn't apply, and we can actually get SLSB_P_OUTPUT_PENDING returned.
So for this case propagating the PENDING state to the driver via the
queue's sbal_state doesn't make sense and creates unnecessary overhead.
Instead introduce a new QDIO_ERROR_* flag that gets passed to the
driver, and triggers the same processing as if the buffers were flagged
as QDIO_OUTBUF_STATE_FLAG_PENDING.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
When inspecting a queue, any error is currently returned back through
the queue's qdio_error field. Turn this into a proper variable that gets
passed through the call chain, so that the lifetime is clear and the
error state can be accessed along the way.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
We don't kick the handler for Input Queues anymore. Move the remaining
code into its only caller.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Lift the dma_default_coherent variable from the mips architecture code
to the driver core. This allows an architecture to sdefault all device
to be DMA coherent at run time, even if the kernel is build with support
for DMA noncoherent device. By allowing device_initialize to set the
->dma_coherent field to this default the amount of arch hooks required
for this behavior can be greatly reduced.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Newer versions of the Xilinx AXI Ethernet core (specifically version 7.2 or
later) allow the core to be configured with a PHY interface mode of "Both",
allowing either 1000BaseX or SGMII modes to be selected at runtime. Add
support for this in the driver to allow better support for applications
which can use both fiber and copper SFP modules.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hook up the nway_reset ethtool operation to the corresponding phylink
function so that "ethtool -r" can be supported.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver is set up to use a clock mapping in the device tree if it is
present, but still work without one for backward compatibility. However,
if getting the clock returns -EPROBE_DEFER, then we need to abort and
return that error from our driver initialization so that the probe can
be retried later after the clock is set up.
Move clock initialization to earlier in the process so we do not waste as
much effort if the clock is not yet available. Switch to use
devm_clk_get_optional and abort initialization on any error reported.
Also enable the clock regardless of whether the controller is using an MDIO
bus, as the clock is required in any case.
Fixes: 09a0354cadec267be7f ("net: axienet: Use clock framework to get device clock rate")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-02-12
This series contains updates to i40e, ice, and ixgbe drivers.
Maciej does cleanups on the following drivers.
For i40e, removes redundant check for XDP prog, cleans up no longer
relevant information, and removes an unused function argument.
For ice, removes local variable use, instead returning values directly.
Moves skb pointer from buffer to ring and removes an unneeded check for
xdp_prog in zero copy path. Also removes a redundant MTU check when
changing it.
For i40e, ice, and ixgbe, stores the rx_offset in the Rx ring as
the value is constant so there's no need for continual calls.
Bjorn folds a decrement into a while statement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_device_node_put() is just a wrapper for of_node_put(). The platform
driver core is already polluted with of_node pointers and the only 'get'
already uses of_node_get() (though typically the get would happen in
of_device_alloc()).
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210211232745.1498137-3-robh@kernel.org
|
|
of_dev_get() and of_dev_put are just wrappers for get_device()/put_device()
on a platform_device. There's also already platform_device_{get,put}()
wrappers for this purpose. Let's update the few users and remove
of_dev_{get,put}().
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Gilles Muller <Gilles.Muller@inria.fr>
Cc: Nicolas Palix <nicolas.palix@imag.fr>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-usb@vger.kernel.org
Cc: cocci@systeme.lip6.fr
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210211232745.1498137-2-robh@kernel.org
|
|
The supported indirect subcrq entries on Power8 is 16. Power9
supports 128. Redefined this value to 16 to minimize the driver from
having to reset when migrating between Power9 and Power8. In our rx/tx
performance testing, we found no performance difference between 16 and
128 at this time.
Fixes: f019fb6392e5 ("ibmvnic: Introduce indirect subordinate Command Response Queue buffer")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chip can configure unicast flooding, broadcast flooding and learning.
Learning is per port, while flooding is per {ingress, egress} port pair
and we need to configure the same value for all possible ingress ports
towards the requested one.
While multicast flooding is not officially supported, we can hack it by
using a feature of the second generation (P/Q/R/S) devices, which is that
FDB entries are maskable, and multicast addresses always have an odd
first octet. So by putting a match-all for 00:01:00:00:00:00 addr and
00:01:00:00:00:00 mask at the end of the FDB, we make sure that it is
always checked last, and does not take precedence in front of any other
MDB. So it behaves effectively as an unknown multicast entry.
For the first generation switches, this feature is not available, so
unknown multicast will always be treated the same as unknown unicast.
So the only thing we can do is request the user to offload the settings
for these 2 flags in tandem, i.e.
ip link set swp2 type bridge_slave flood off
Error: sja1105: This chip cannot configure multicast flooding independently of unicast.
ip link set swp2 type bridge_slave flood off mcast_flood off
ip link set swp2 type bridge_slave mcast_flood on
Error: sja1105: This chip cannot configure multicast flooding independently of unicast.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not be unconditionally enabling address learning, since doing
that is actively detrimential when a port is standalone and not offloading
a bridge. Namely, if a port in the switch is standalone and others are
offloading the bridge, then we could enter a situation where we learn an
address towards the standalone port, but the bridged ports could not
forward the packet there, because the CPU is the only path between the
standalone and the bridged ports. The solution of course is to not
enable address learning unless the bridge asks for it.
We need to set up the initial port flags for no learning and flooding
everything, and also when the port joins and leaves the bridge.
The flood configuration was already configured ok for standalone mode
in ocelot_init, we just need to disable learning in ocelot_init_port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation of offloading the bridge port flags which have
independent settings for unknown multicast and for broadcast, we should
also start reserving one destination Port Group ID for the flooding of
broadcast packets, to allow configuring it individually.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ocelot_init sets up PGID_MC to include the CPU port module, and that is
fine, but the ocelot-8021q tagger removes the CPU port module from the
unknown multicast replicator. So after a transition from the default
ocelot tagger towards ocelot-8021q and then again towards ocelot,
multicast flooding towards the CPU port module will be disabled.
Fixes: e21268efbe26 ("net: dsa: felix: perform switch setup for tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are multiple ways in which a PORT_BRIDGE_FLAGS attribute can be
expressed by the bridge through switchdev, and not all of them can be
emulated by DSA mid-layer API at the same time.
One possible configuration is when the bridge offloads the port flags
using a mask that has a single bit set - therefore only one feature
should change. However, DSA currently groups together unicast and
multicast flooding in the .port_egress_floods method, which limits our
options when we try to add support for turning off broadcast flooding:
do we extend .port_egress_floods with a third parameter which b53 and
mv88e6xxx will ignore? But that means that the DSA layer, which
currently implements the PRE_BRIDGE_FLAGS attribute all by itself, will
see that .port_egress_floods is implemented, and will report that all 3
types of flooding are supported - not necessarily true.
Another configuration is when the user specifies more than one flag at
the same time, in the same netlink message. If we were to create one
individual function per offloadable bridge port flag, we would limit the
expressiveness of the switch driver of refusing certain combinations of
flag values. For example, a switch may not have an explicit knob for
flooding of unknown multicast, just for flooding in general. In that
case, the only correct thing to do is to allow changes to BR_FLOOD and
BR_MCAST_FLOOD in tandem, and never allow mismatched values. But having
a separate .port_set_unicast_flood and .port_set_multicast_flood would
not allow the driver to possibly reject that.
Also, DSA doesn't consider it necessary to inform the driver that a
SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute was offloaded, because it
just calls .port_egress_floods for the CPU port. When we'll add support
for the plain SWITCHDEV_ATTR_ID_PORT_MROUTER, that will become a real
problem because the flood settings will need to be held statefully in
the DSA middle layer, otherwise changing the mrouter port attribute will
impact the flooding attribute. And that's _assuming_ that the underlying
hardware doesn't have anything else to do when a multicast router
attaches to a port than flood unknown traffic to it. If it does, there
will need to be a dedicated .port_set_mrouter anyway.
So we need to let the DSA drivers see the exact form that the bridge
passes this switchdev attribute in, otherwise we are standing in the
way. Therefore we also need to use this form of language when
communicating to the driver that it needs to configure its initial
(before bridge join) and final (after bridge leave) port flags.
The b53 and mv88e6xxx drivers are converted to the passthrough API and
their implementation of .port_egress_floods is split into two: a
function that configures unicast flooding and another for multicast.
The mv88e6xxx implementation is quite hairy, and it turns out that
the implementations of unknown unicast flooding are actually the same
for 6185 and for 6352:
behind the confusing names actually lie two individual bits:
NO_UNKNOWN_MC -> FLOOD_UC = 0x4 = BIT(2)
NO_UNKNOWN_UC -> FLOOD_MC = 0x8 = BIT(3)
so there was no reason to entangle them in the first place.
Whereas the 6185 writes to MV88E6185_PORT_CTL0_FORWARD_UNKNOWN of
PORT_CTL0, which has the exact same bit index. I have left the
implementations separate though, for the only reason that the names are
different enough to confuse me, since I am not able to double-check with
a user manual. The multicast flooding setting for 6185 is in a different
register than for 6352 though.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switchdev attribute offers a counterproductive API for a driver
writer, because although br_switchdev_set_port_flag gets passed a
"flags" and a "mask", those are passed piecemeal to the driver, so while
the PRE_BRIDGE_FLAGS listener knows what changed because it has the
"mask", the BRIDGE_FLAGS listener doesn't, because it only has the final
value. But certain drivers can offload only certain combinations of
settings, like for example they cannot change unicast flooding
independently of multicast flooding - they must be both on or both off.
The way the information is passed to switchdev makes drivers not
expressive enough, and unable to reject this request ahead of time, in
the PRE_BRIDGE_FLAGS notifier, so they are forced to reject it during
the deferred BRIDGE_FLAGS attribute, where the rejection is currently
ignored.
This patch also changes drivers to make use of the "mask" field for edge
detection when possible.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a struct switchdev_attr is notified through switchdev, there is no
way to report informational messages, unlike for struct switchdev_obj.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 93efb0c656837 ("octeontx2-pf: Fix out-of-bounds read in otx2_get_fecparam()")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a simple helper function that indicates whether a channel has
been initialized. This abstacts/hides the details of how this is
determined.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new function to abstract the knowledge of whether hashed
routing and filter tables are supported for a given IPA instance.
IPA v4.2 is the only one that doesn't support hashed tables (now
and for the foreseeable future), but the name of the helper function
is better for explaining what's going on.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ipa_cmd_register_write_valid() we verify that values we will
supply to a REGISTER_WRITE IPA immediate command will fit in
the fields that need to hold them. This patch fixes some issues
in that function and ipa_cmd_register_write_offset_valid().
The dev_err() call in ipa_cmd_register_write_offset_valid() has
some printf format errors:
- The name of the register (corresponding to the string format
specifier) was not supplied.
- The IPA base offset and offset need to be supplied separately to
match the other format specifiers.
Also make the ~0 constant used there to compute the maximum
supported offset value explicitly unsigned.
There are two other issues in ipa_cmd_register_write_valid():
- There's no need to check the hash flush register for platforms
(like IPA v4.2) that do not support hashed tables
- The highest possible endpoint number, whose status register
offset is computed, is COUNT - 1, not COUNT.
Fix these problems, and add some additional commentary.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When initializing the IPA core clock and interconnects, it's
possible we'll get an EPROBE_DEFER error. This isn't really an
error, it's just means we need to be re-probed later.
Use dev_err_probe() to report the error rather than dev_err().
This avoids polluting the log with these "error" messages.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch actually fixes a bug, though it doesn't affect the two
platforms supported currently. The fix implements GSI memory
pointers a bit differently.
For IPA version 4.5 and above, the address space for almost all GSI
registers is adjusted downward by a fixed amount. This is currently
handled by adjusting the I/O virtual address pointer after it has
been mapped. The bug is that the pointer is not "de-adjusted" as it
should be when it's unmapped.
This patch fixes that error, but it does so by maintaining one "raw"
pointer for the mapped memory range. This is assigned when the
memory is mapped and used to unmap the memory. This pointer is also
used to access the two registers that do *not* sit in the "adjusted"
memory space.
Rather than adjusting *that* pointer, we maintain a separate pointer
that's an adjusted copy of the "raw" pointer, and that is used for
most GSI register accesses.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code at line 967 implies that rsp->fwdata.supported_fec may be up to 4:
967: if (rsp->fwdata.supported_fec <= FEC_MAX_INDEX)
If rsp->fwdata.supported_fec evaluates to 4, then there is an
out-of-bounds read at line 971 because fec is an array with
a maximum of 4 elements:
954 const int fec[] = {
955 ETHTOOL_FEC_OFF,
956 ETHTOOL_FEC_BASER,
957 ETHTOOL_FEC_RS,
958 ETHTOOL_FEC_BASER | ETHTOOL_FEC_RS};
959 #define FEC_MAX_INDEX 4
971: fecparam->fec = fec[rsp->fwdata.supported_fec];
Fix this by properly indexing fec[] with rsp->fwdata.supported_fec - 1.
In this case the proper indexes 0 to 3 are used when
rsp->fwdata.supported_fec evaluates to a range of 1 to 4, correspondingly.
Fixes: d0cf9503e908 ("octeontx2-pf: ethtool fec mode support")
Addresses-Coverity-ID: 1501722 ("Out-of-bounds read")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in the text in array rpm_rx_stats_fields,
fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.12
Second set of patches for v5.12. Last time there was a smaller pull
request so unsurprisingly this time we have a big one. mt76 has new
hardware support and lots of new features, iwlwifi getting new
features and rtw88 got NAPI support. And the usual cleanups and fixes
all over.
Major changes:
ath10k
* support setting SAR limits via nl80211
rtw88
* support 8821 RFE type2 devices
* NAPI support
iwlwifi
* add new FW API support
* support for new So devices
* support for RF interference mitigation (RFI)
* support for PNVM (Platform Non-Volatile Memory, a firmware data
file) from BIOS
mt76
* add new mt7921e driver
* 802.11 encap offload support
* support for multiple pcie gen1 host interfaces on 7915
* 7915 testmode support
* 7915 txbf support
brcmfmac
* support for CQM RSSI notifications
wil6210
* support for extended DMG MCS 12.1 rate
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
