| Age | Commit message (Collapse) | Author |
|---|
|
The return type of jsm_get_mstat was int, and the local var result
was for the return should be int, make the change.
This patch fixes the checkpatch.pl warning:
Prefer 'unsigned int' to bare use of 'unsigned'.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During system-wide PM, genpd relies on its PM callbacks to be invoked for
all its attached devices, as to deal with powering off/on the PM domain. In
other words, genpd is not compatible with the direct_complete path, if
executed by the PM core for any of its attached devices.
However, when genpd's ->prepare() callback invokes pm_generic_prepare(), it
does not take into account that it may return 1. Instead it treats that as
an error internally and expects the PM core to abort the prepare phase and
roll back. This leads to genpd not properly powering on/off the PM domain,
because its internal counters gets wrongly balanced.
To fix the behaviour, allow drivers to return 1 from their ->prepare()
callbacks, but let's return 0 from genpd's ->prepare() callback in such
case, as that prevents the PM core from running the direct_complete path
for the device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Individual CPUs may have special requirements to not enter
deep idle states. For example, a CPU running real time
applications would not want to enter deep idle states to
avoid latency impacts. At the same time other CPUs that
do not have such a requirement could allow deep idle
states to save power.
This was already implemented in the menu governor.
Implementing similar changes in the ladder governor which
gets selected when CONFIG_NO_HZ and CONFIG_NO_HZ_IDLE are not
set. Refer following commits for the menu governor changes.
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
The special value of 0 for device resume latency PM QoS means
"no restriction", but there are two problems with that.
First, device resume latency PM QoS requests with 0 as the
value are always put in front of requests with positive
values in the priority lists used internally by the PM QoS
framework, causing 0 to be chosen as an effective constraint
value. However, that 0 is then interpreted as "no restriction"
effectively overriding the other requests with specific
restrictions which is incorrect.
Second, the users of device resume latency PM QoS have no
way to specify that *any* resume latency at all should be
avoided, which is an artificial limitation in general.
To address these issues, modify device resume latency PM QoS to
use S32_MAX as the "no constraint" value and 0 as the "no
latency at all" one and rework its users (the cpuidle menu
governor, the genpd QoS governor and the runtime PM framework)
to follow these changes.
Also add a special "n/a" value to the corresponding user space I/F
to allow user space to indicate that it cannot accept any resume
latencies at all for the given device.
Fixes: 85dc0b8a4019 (PM / QoS: Make it possible to expose PM QoS latency constraints)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197323
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Ramesh Thomas <ramesh.thomas@intel.com>
|
|
|
|
The genpd governor currently uses negative PM QoS values to indicate
the "no suspend" condition and 0 as "no restriction", but it doesn't
use them consistently. Moreover, it tries to refresh QoS values for
already suspended devices in a quite questionable way.
For the above reasons, rework it to be a bit more consistent.
First off, note that dev_pm_qos_read_value() in
dev_update_qos_constraint() and __default_power_down_ok() is
evaluated for devices in suspend. Moreover, that only happens if the
effective_constraint_ns value for them is negative (meaning "no
suspend"). It is not evaluated in any other cases, so effectively
the QoS values are only updated for devices in suspend that should
not have been suspended in the first place. In all of the other
cases, the QoS values taken into account are the effective ones from
the time before the device has been suspended, so generally devices
need to be resumed and suspended again for new QoS values to take
effect anyway. Thus evaluating dev_update_qos_constraint() in
those two places doesn't make sense at all, so drop it.
Second, initialize effective_constraint_ns to 0 ("no constraint")
rather than to (-1) ("no suspend"), which makes more sense in
general and in case effective_constraint_ns is never updated
(the device is in suspend all the time or it is never suspended)
it doesn't affect the device's parent and so on.
Finally, rework default_suspend_ok() to explicitly handle the
"no restriction" and "no suspend" special cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Ramesh Thomas <ramesh.thomas@intel.com>
|
|
The variable len is assigned but never read, therefore it is redundant
and can be removed. Cleans up clang warning:
drivers/video/backlight/ili922x.c:276:2: warning: Value stored to 'len'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We added a new error path here but we forgot to drop the lock first
before returning.
Fixes: 0d44374c1aae ("tcmu: fix double se_cmd completion")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
"udev->nl_reply_supported" is an int but on 64 bit arches we are writing
8 bytes of data to it so it corrupts four bytes beyond the end of the
struct.
Fixes: b849b4567549 ("target: Add netlink command reply supported option for each device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When we receive a packet on a QMI device in raw IP mode, we should call
skb_reset_mac_header() to ensure that skb->mac_header contains a valid
offset in the packet. While it shouldn't really matter, the packets have
no MAC header and the interface is configured as-such, it seems certain
parts of the network stack expects a "good" value in skb->mac_header.
Without the skb_reset_mac_header() call added in this patch, for example
shaping traffic (using tc) triggers the following oops on the first
received packet:
[ 303.642957] skbuff: skb_under_panic: text:8f137918 len:177 put:67 head:8e4b0f00 data:8e4b0eff tail:0x8e4b0fb0 end:0x8e4b1520 dev:wwan0
[ 303.655045] Kernel bug detected[#1]:
[ 303.658622] CPU: 1 PID: 1002 Comm: logd Not tainted 4.9.58 #0
[ 303.664339] task: 8fdf05e0 task.stack: 8f15c000
[ 303.668844] $ 0 : 00000000 00000001 0000007a 00000000
[ 303.674062] $ 4 : 8149a2fc 8149a2fc 8149ce20 00000000
[ 303.679284] $ 8 : 00000030 3878303a 31623465 20303235
[ 303.684510] $12 : ded731e3 2626a277 00000000 03bd0000
[ 303.689747] $16 : 8ef62b40 00000043 8f137918 804db5fc
[ 303.694978] $20 : 00000001 00000004 8fc13800 00000003
[ 303.700215] $24 : 00000001 8024ab10
[ 303.705442] $28 : 8f15c000 8fc19cf0 00000043 802cc920
[ 303.710664] Hi : 00000000
[ 303.713533] Lo : 74e58000
[ 303.716436] epc : 802cc920 skb_panic+0x58/0x5c
[ 303.721046] ra : 802cc920 skb_panic+0x58/0x5c
[ 303.725639] Status: 11007c03 KERNEL EXL IE
[ 303.729823] Cause : 50800024 (ExcCode 09)
[ 303.733817] PrId : 0001992f (MIPS 1004Kc)
[ 303.737892] Modules linked in: rt2800pci rt2800mmio rt2800lib qcserial ppp_async option usb_wwan rt2x00pci rt2x00mmio rt2x00lib rndis_host qmi_wwan ppp_generic nf_nat_pptp nf_conntrack_pptp nf_conntrack_ipv6 mt76x2i
Process logd (pid: 1002, threadinfo=8f15c000, task=8fdf05e0, tls=77b3eee4)
[ 303.962509] Stack : 00000000 80408990 8f137918 000000b1 00000043 8e4b0f00 8e4b0eff 8e4b0fb0
[ 303.970871] 8e4b1520 8fec1800 00000043 802cd2a4 6e000045 00000043 00000000 8ef62000
[ 303.979219] 8eef5d00 8ef62b40 8fea7300 8f137918 00000000 00000000 0002bb01 793e5664
[ 303.987568] 8ef08884 00000001 8fea7300 00000002 8fc19e80 8eef5d00 00000006 00000003
[ 303.995934] 00000000 8030ba90 00000003 77ab3fd0 8149dc80 8004d1bc 8f15c000 8f383700
[ 304.004324] ...
[ 304.006767] Call Trace:
[ 304.009241] [<802cc920>] skb_panic+0x58/0x5c
[ 304.013504] [<802cd2a4>] skb_push+0x78/0x90
[ 304.017783] [<8f137918>] 0x8f137918
[ 304.021269] Code: 00602825 0c02a3b4 24842888 <000c000d> 8c870060 8c8200a0 0007382b 00070336 8c88005c
[ 304.031034]
[ 304.032805] ---[ end trace b778c482b3f0bda9 ]---
[ 304.041384] Kernel panic - not syncing: Fatal exception in interrupt
[ 304.051975] Rebooting in 3 seconds..
While the oops is for a 4.9-kernel, I was able to trigger the same oops with
net-next as of yesterday.
Fixes: 32f7adf633b9 ("net: qmi_wwan: support "raw IP" mode")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bonding miimon logic has a flaw, in that a failure of the
rtnl_trylock can cause a slave to become permanently stuck in
BOND_LINK_FAIL state.
The sequence of events to cause this is as follows:
1) bond_miimon_inspect finds that a slave's link is down, and so
calls bond_propose_link_state, setting slave->new_link_state to
BOND_LINK_FAIL, then sets slave->new_link to BOND_LINK_DOWN and returns
non-zero.
2) In bond_mii_monitor, the rtnl_trylock fails, and the timer is
rescheduled. No change is committed.
3) bond_miimon_inspect is called again, but this time the slave
from step 1 has recovered. slave->new_link is reset to NOCHANGE, and, as
slave->link was never changed, the switch enters the BOND_LINK_UP case,
and does nothing. The pending BOND_LINK_FAIL state from step 1 remains
pending, as new_link_state is not reset.
4) The state from step 3 persists until another slave changes link
state and causes bond_miimon_inspect to return non-zero. At this point,
the BOND_LINK_FAIL state change on the slave from steps 1-3 is committed,
and the slave will remain stuck in BOND_LINK_FAIL state even though it
is actually link up.
The remedy for this is to initialize new_link_state on each entry
to bond_miimon_inspect, as is already done with new_link.
Fixes: fb9eb899a6dc ("bonding: handle link transition from FAIL to UP correctly")
Reported-by: Alex Sidorenko <alexandre.sidorenko@hpe.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define for reserved register 31 had the incorrect address. Specify
the correct address.
Reported-by: Jens-Peter Oswald <oswald@lre.de>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Remove duplicate define for RX8010_YEAR
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
m41t80_sqw_set_rate will be called with the result from
m41t80_sqw_round_rate, so might as well make
m41t80_sqw_set_rate(n) same as
m41t80_sqw_set_rate(m41t80_sqw_round_rate(n))
As Russell King wrote[1],
"clk_round_rate() is supposed to tell you what you end up with if you
ask clk_set_rate() to set the exact same value you passed in - but
clk_round_rate() won't modify the hardware."
[1]
http://lists.infradead.org/pipermail/linux-arm-kernel/2012-January/080175.html
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
This is a little more efficient and avoids the warning
WARNING: possible circular locking dependency detected
4.14.0-rc7-00010 #16 Not tainted
------------------------------------------------------
kworker/2:1/70 is trying to acquire lock:
(prepare_lock){+.+.}, at: [<c049300c>] clk_prepare_lock+0x80/0xf4
but task is already holding lock:
(i2c_register_adapter){+.+.}, at: [<c0690b04>]
i2c_adapter_lock_bus+0x14/0x18
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (i2c_register_adapter){+.+.}:
rt_mutex_lock+0x44/0x5c
i2c_adapter_lock_bus+0x14/0x18
i2c_transfer+0xa8/0xbc
i2c_smbus_xfer+0x20c/0x5d8
i2c_smbus_read_byte_data+0x38/0x48
m41t80_sqw_is_prepared+0x18/0x28
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
This is a little more efficient, and avoids the warning
WARNING: possible circular locking dependency detected
4.14.0-rc7-00007 #14 Not tainted
------------------------------------------------------
alsactl/330 is trying to acquire lock:
(prepare_lock){+.+.}, at: [<c049300c>] clk_prepare_lock+0x80/0xf4
but task is already holding lock:
(i2c_register_adapter){+.+.}, at: [<c0690ae0>]
i2c_adapter_lock_bus+0x14/0x18
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (i2c_register_adapter){+.+.}:
rt_mutex_lock+0x44/0x5c
i2c_adapter_lock_bus+0x14/0x18
i2c_transfer+0xa8/0xbc
i2c_smbus_xfer+0x20c/0x5d8
i2c_smbus_read_byte_data+0x38/0x48
m41t80_sqw_recalc_rate+0x24/0x58
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Previously it was returning the best of
32768, 8192, 1024, 64, 2, 0
Now, best of
32768, 8192, 4096, 2048, 1024, 512, 256, 128,
64, 32, 16, 8, 4, 2, 1, 0
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Previously it was returning -EINVAL upon success.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Note that alarms are not currently implemented.
64 bytes of nvmem is supported and exposed in
sysfs (# is the instance number, starting with 0):
/sys/bus/nvmem/devices/pcf85363-#/nvmem
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Register an nvmem device to expose the 3 scratch registers (total of 12
bytes) to both userspace and kernel space.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Commit adfa543e7314 ("dmatest: don't use set_freezable_with_signal()")
introduced a bug (that is in fact documented by the patch commit text)
that leaves behind a dangling pointer. Since the done_wait structure is
allocated on the stack, future invocations to the DMATEST can produce
undesirable results (e.g., corrupted spinlocks). Ideally, this would be
cleaned up in the thread handler, but at the very least, the kernel
is left in a very precarious scenario that can lead to some long debug
sessions when the crash comes later.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197605
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This reverts commit 847449f23dcb: ("dmaengine: rcar-dmac: use TCRB instead
of TCR for residue") as it breaks small serial console.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If source and destination bus width differs pack/unpack MDMA
feature has to be activated for alignment.
This pack/unpack feature implies to have both source/destination address
and buffer length aligned on bus width.
Fixes: a4ffb13c8946 ("dmaengine: Add STM32 MDMA driver")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since commit 3cab1e711297 ("lib/vsprintf: refactor duplicate code
to special_hex_number()") %pad doesn't need 0x prefix so drop that.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since commit 3cab1e711297 ("lib/vsprintf: refactor duplicate code
to special_hex_number()") %pad doesn't need 0x prefix so drop that.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add ethtool statistics support by reading the GOP statistics from the
hardware counters. Also implement a workqueue to gather the statistics
every second or some 32-bit counters could overflow.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Memory allocation functions already display some informaton in case of
memory allocation failure. There is no need to add an extra 'dev_err' here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If 'of_phy_find_device()' fails, we must undo the previous 'of_node_get()'
call, as done the the following error handling code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to release explicitly some devm_ allocated resources.
If the 'mac_probe()' probe function fails, they will be released
automatically, as already done in the other error handling paths of
this function.
Also goto '_return_of_get_parent' as in the other error handling paths.
This is useless (priv->fixed_link is NULL at this point), but at least
it is consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c6e26ea8c893 ("dpaa_eth: change device used") has removed usage of
'dev_set_drvdata()' in the 'mac_probe() function.
This call should also be axed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A CDC Ethernet functional descriptor with wMaxSegmentSize = 0 will
cause a divide error in usbnet_probe:
divide error: 0000 [#1] PREEMPT SMP KASAN
Modules linked in:
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.14.0-rc8-44453-g1fdc1a82c34f #56
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task: ffff88006bef5c00 task.stack: ffff88006bf60000
RIP: 0010:usbnet_update_max_qlen+0x24d/0x390 drivers/net/usb/usbnet.c:355
RSP: 0018:ffff88006bf67508 EFLAGS: 00010246
RAX: 00000000000163c8 RBX: ffff8800621fce40 RCX: ffff8800621fcf34
RDX: 0000000000000000 RSI: ffffffff837ecb7a RDI: ffff8800621fcf34
RBP: ffff88006bf67520 R08: ffff88006bef5c00 R09: ffffed000c43f881
R10: ffffed000c43f880 R11: ffff8800621fc406 R12: 0000000000000003
R13: ffffffff85c71de0 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88006ca00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffe9c0d6dac CR3: 00000000614f4000 CR4: 00000000000006f0
Call Trace:
usbnet_probe+0x18b5/0x2790 drivers/net/usb/usbnet.c:1783
qmi_wwan_probe+0x133/0x220 drivers/net/usb/qmi_wwan.c:1338
usb_probe_interface+0x324/0x940 drivers/usb/core/driver.c:361
really_probe drivers/base/dd.c:413
driver_probe_device+0x522/0x740 drivers/base/dd.c:557
Fix by simply ignoring the bogus descriptor, as it is optional
for QMI devices anyway.
Fixes: 423ce8caab7e ("net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting dev->hard_mtu to 0 will cause a divide error in
usbnet_probe. Protect against devices with bogus CDC Ethernet
functional descriptors by ignoring a zero wMaxSegmentSize.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that ds->num_ports is 3, there is no need to check range of "port"
parameter.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit architectures, rtc_time_to_tm() returns incorrect results
in 2038 or later, and do_gettimeofday() is broken for the same reason.
This changes the code to use ktime_get_real_seconds() and time64_to_tm()
instead, both of them are 2038-safe, and we can also get rid of the
CONFIG_RTC_LIB dependency that way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We return on the previous line so this "return 0;" statement should just
be deleted.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove scripts/checkpatch.pl CHECKs by adjusting indenting.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove scripts/checkpatch.pl WARNING by replacing msleep(1) with usleep_range()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code from the VID create error handling
case instead of 0, as done elsewhere in this function.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code from the dpaa_bp_alloc() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a se_cmd->cmd_kref reference leak that can
occur when a non immediate TMR is proceeded our of command
sequence number order, and CMDSN_LOWER_THAN_EXP is returned
by iscsit_sequence_cmd().
To address this bug, call target_put_sess_cmd() during this
special case following what iscsit_process_scsi_cmd() does
upon CMDSN_LOWER_THAN_EXP.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Since commit 59b6986dbf fixed a potential NULL pointer dereference
by allocating a se_tmr_req for ISCSI_TM_FUNC_TASK_REASSIGN, the
se_tmr_req is currently leaked by iscsit_free_cmd() because no
iscsi_cmd->se_cmd.se_tfo was associated.
To address this, treat ISCSI_TM_FUNC_TASK_REASSIGN like any other
TMR and call transport_init_se_cmd() + target_get_sess_cmd() to
setup iscsi_cmd->se_cmd.se_tfo with se_cmd->cmd_kref of 2.
This will ensure normal release operation once se_cmd->cmd_kref
reaches zero and target_release_cmd_kref() is invoked, se_tmr_req
will be released via existing target_free_cmd_mem() and
core_tmr_release_req() code.
Reported-by: Donald White <dew@datera.io>
Cc: Donald White <dew@datera.io>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes bug where early se_cmd exceptions that occur
before backend execution can result in use-after-free if/when
a subsequent ABORT_TASK occurs for the same tag.
Since an early se_cmd exception will have had se_cmd added to
se_session->sess_cmd_list via target_get_sess_cmd(), it will
not have CMD_T_COMPLETE set by the usual target_complete_cmd()
backend completion path.
This causes a subsequent ABORT_TASK + __target_check_io_state()
to signal ABORT_TASK should proceed. As core_tmr_abort_task()
executes, it will bring the outstanding se_cmd->cmd_kref count
down to zero releasing se_cmd, after se_cmd has already been
queued with error status into fabric driver response path code.
To address this bug, introduce a CMD_T_PRE_EXECUTE bit that is
set at target_get_sess_cmd() time, and cleared immediately before
backend driver dispatch in target_execute_cmd() once CMD_T_ACTIVE
is set.
Then, check CMD_T_PRE_EXECUTE within __target_check_io_state() to
determine when an early exception has occured, and avoid aborting
this se_cmd since it will have already been queued into fabric
driver response path code.
Reported-by: Donald White <dew@datera.io>
Cc: Donald White <dew@datera.io>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a potential end-less loop during QUEUE_FULL,
where cmd->se_tfo->write_pending() callback fails repeatedly
but __transport_wait_for_tasks() has already been invoked to
quiese the outstanding se_cmd descriptor.
To address this bug, this patch adds a CMD_T_STOP|CMD_T_ABORTED
check within transport_write_pending_qf() and invokes the
existing se_cmd->t_transport_stop_comp to signal quiese
completion back to __transport_wait_for_tasks().
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: Potnuri Bharat Teja <bharat@chelsio.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
With the recent addition of transport_check_aborted_status() within
transport_generic_request_failure() to avoid sending a SCSI status
exception after CMD_T_ABORTED w/ TAS=1 has occured, it introduced
a COMPARE_AND_WRITE early failure regression.
Namely when COMPARE_AND_WRITE fails and se_device->caw_sem has
been taken by sbc_compare_and_write(), if the new check for
transport_check_aborted_status() returns true and exits,
cmd->transport_complete_callback() -> compare_and_write_post()
is skipped never releasing se_device->caw_sem.
This regression was originally introduced by:
commit e3b88ee95b4e4bf3e9729a4695d695b9c7c296c8
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Tue Feb 14 16:25:45 2017 -0800
target: Fix handling of aborted failed commands
To address this bug, move the transport_check_aborted_status()
call after transport_complete_task_attr() and
cmd->transport_complete_callback().
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug during QUEUE_FULL where transport_complete_qf()
calls transport_complete_task_attr() after it's already been invoked
by target_complete_ok_work() or transport_generic_request_failure()
during initial completion, preceeding QUEUE_FULL.
This will result in se_device->simple_cmds, se_device->dev_cur_ordered_id
and/or se_device->dev_ordered_sync being updated multiple times for
a single se_cmd.
To address this bug, clear SCF_TASK_ATTR_SET after the first call
to transport_complete_task_attr(), and avoid updating SCSI task
attribute related counters for any subsequent calls.
Also, when a se_cmd is deferred due to ordered tags and executed
via target_restart_delayed_cmds(), set CMD_T_SENT before execution
matching what target_execute_cmd() does.
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_QDISC_STATS. This call updates the generic qdisc stats from the
cache if the handle ID that is asked for matching the root qdisc ID and
fails otherwise.
Currently doesn't support qlen and rqueues.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_RED_XSTATS. This call returns the RED qdisc xstats from the cache
if the handle ID that is asked for matching the root qdisc ID and fails
otherwise.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add more statistics to be collected from the HW periodically. These stats
are tclass based (beside ECN marked packet, that exist only port based).
They are needed to expose RED qdisc stats and xstats correctly.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
