| Age | Commit message (Collapse) | Author |
|---|
|
Add more data to 64bit SoCs for the cpufreq support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Core support code for CPU frequency changes, which will be used by
the generic cpufreq driver.
The register view is different from the generic clk-mux; it has
a separate status register, and an update bit to load the register
setting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-12-07
This series contains updates to i40e and i40evf only.
Filip modifies the i40e to log link speed change and when the link is
brought up and down.
Mitch replaces i40e_txd_use_count() with a new function which is slightly
faster and better documented so the dim witted can better follow the
code. Fixes the locking of the service task so that it is actually
done in the service task and not in the scheduling function which calls
the service task.
Jacob, being the busy little beaver he is, provides most of the changes
starting restores a workaround that is still needed in some configurations,
specifically the Ethernet Controller XL710 for 40GbE QSFP+. Removes
duplicate code and simplifies the i40e_vsi_add_vlan() and
i40e_vsi_kill_vlan() functions. Removes detection of PTP frames over L4
(UDP) on the XL710 MAC, since there was a product decision to defeature
it. Fixed a previous refactor of active filters which caused issues in
the accounting of active_filters. Remaining work was done in the VLAN
filters to improve readability and simplify code as much as possible
to reduce inconsistencies.
Alex fixes foul budget accounting in core code by returning actual
work done, capped to budget-1.
Henry fixes the "ethtool -p" function for 1G BaseT PHYs.
Carolyn adds support for 25G devices for i40e and i40evf.
Michal adds functions to apply the correct access method for external PHYs
which could use Clause22 or Clause45 depending on the PHY.
v2: dropped last patch from previous series, since changes are needed based
on feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And simplify the MSI-X logic in general - just request the two vectors
directly instead of going through an indirection table.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In the hip06 and hip07 SoCs, the interrupt lines from the SAS
controllers are connected to mbigen hw module [1]. The mbigen module is
probed with module_init, and, as such, is not guaranteed to probe before
the SAS driver. So we need to support deferred probe.
We check for probe deferral in the hw layer probe, so we not probe into
the main layer and allocate shost, memories, etc., to later learn that
we need to defer the probe.
[1] ./Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
[mkp: fixed bad indentation]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NetApp did confirm this is not required.
Cc: Martin George <Martin.George@netapp.com>
Cc: Robert Stankey <Robert.Stankey@netapp.com>
Cc: Steven Schremmer <Steven.Schremmer@netapp.com>
Cc: Sean Stewart <Sean.Stewart@netapp.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christophe Varoqui <christophe.varoqui@opensvc.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Cc: device-mapper development <dm-devel@redhat.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Reviewed-by: Sean Stewart <sean.stewart@netapp.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If Slot Status indicates changes in both Data Link Layer Status and
Presence Detect, prioritize the Link status change.
When both events are observed, pciehp currently relies on the Slot Status
Presence Detect State (PDS) to agree with the Link Status Data Link Layer
Active status. The Presence Detect State, however, may be set to 1 through
out-of-band presence detect even if the link is down, which creates
conflicting events.
Since the Link Status accurately reflects the reachability of the
downstream bus, the Link Status event should take precedence over a
Presence Detect event. Skip checking the PDC status if we handled a link
event in the same handler.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Add fallback compatibility string for the R-Car Gen 3 family. This is in
keeping with the both the existing fallback compatibility string for the
R-Car Gen 2 family and the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Improve readability by listing fallback compatibility strings after the
more-specific compatibility strings they provide a fallback for.
This does not affect run-time behaviour as it is the order in the DTB that
determines which compatibility string is used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Improve readability by listing fallback compatibility strings after the
more-specific compatibility strings they provide a fallback for.
This does not affect run-time behaviour as it is the order in the DTB that
determines which compatibility string is used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
SCT Write Same support had been introduced with
commit 7b2030942859 ("libata: Add support for SCT Write Same")
Some problems, namely excessive userspace segfaults, had been reported at
http://lkml.kernel.org/r/20160908192736.GA4356@gmail.com
This lead to commit 0ce1b18c42a5 ("libata: Some drives failing on
SCT Write Same") which strived to disable SCT Write Same on !ZAC devices.
Due to the way this was done and to the logic in sd_config_write_same(),
this didn't work for those devices that have
->max_ws_blocks > SD_MAX_WS10_BLOCKS: for these, ->no_write_same and
->max_write_same_sectors would still be non-zero,
but ->ws10 == ->ws16 == 0. This would cause sd_setup_write_same_cmnd() to
demultiplex REQ_OP_WRITE_SAME requests to WRITE_SAME, and these in turn
aren't supported by libata-scsi:
EXT4-fs (dm-1): Delayed block allocation failed for inode 2625094 at
logical offset 2032 with max blocks 2 with error 121
EXT4-fs (dm-1): This should not happen!! Data will be lost
121 == EREMOTEIO is what scsi_io_completion() asserts in case of
invalid opcodes.
Back to the original problem of userspace segfaults: this can be tracked
down to ata_format_sct_write_same() overwriting the input page. Sometimes,
this page is ZERO_PAGE(0) which ceases to be filled with zeros from that
point on. Since ZERO_PAGE(0) is used for userspace .bss mappings, code of
the following is doomed:
static char *a = NULL; /* .bss */
...
if (a)
*a = 'a';
This problem is not solved by disabling SCT Write Same for !ZAC devices
only.
It can certainly be fixed, but the final release is quite close -- so
disable SCT Write Same for all ATA devices rather than introducing some
SCT key buffer allocation schemes at this point.
Fixes: 7b2030942859 ("libata: Add support for SCT Write Same")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Move deassert of pm/aclk/pclk after phy_init() as we want to optimize the
logic of reset control and reuse rockchip_pcie_init_port() later which
should fully follow the cold boot procedure of ROM code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
|
|
Split out a new function, rockchip_cfg_atu(), in order to re-configure the
ATU when missing these information after wakeup from S3.
[bhelgaas: add "dev" temporary, return 0 when known]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
|
|
PCIE_RC_CONFIG_LCS contains control and status bits specific to the PCIe
link. The layout for this register looks the same as the existing
PCI_EXP_LNKCTL and PCI_EXP_LNKSTA. So let's reuse them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We're trying to mask out bits[23:8] while retaining [32:24, 7:0], but we're
doing the inverse. That doesn't have too much effect, since we're setting
all the [23:8] bits to 1, and the other bits are only relevant for modes
we're currently not using. But we should get this right.
Fixes: ca1989084054 ("PCI: rockchip: Fix wrong transmitted FTS count")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
Per the errata of TRM, the RC can't support L1 substate, so remove the L1
substate cap as well as operation for PCIE_RC_CONFIG_L1_SUBSTATE_CTRL2.
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
rk3399 supports PCIe 2.x link speeds marginally at best, and on some
boards, the link won't train at 5 GT/s at all. Rather than sacrifice 500ms
waiting for training that will never happen, let's use the helper function,
of_pci_get_max_link_speed(), to get the max link speed from DT and specify
link capability.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The calculation of negotiated lanes is wrong: it should be shifted by
PCIE_CORE_PL_CONF_LANE_SHIFT, but it is shifted by
PCIE_CORE_PL_CONF_LANE_MASK instead. Let's fix it.
Fixes: e77f847df54c ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Allow selection of the Rockchip driver for compile testing, even if we
aren't building for ARCH_ROCKCHIP.
[bhelgaas: changelog]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The default value of common clock configuration is zero indicating
Rockchip's RC is using asynchronous clock architecture but actually we are
using common clock. This will confuse some EP drivers if they need some
different settings referring to this value.
Set the Common Clock Configuration bit in the Link Control Register.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If vpcie3v3 is available, we could provide these information via RC's
configure register to make EP able to know the power limit.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add Makefile comments to explain the Kconfig and build strategy for ARM64
drivers that work around not-quite-ECAM issues. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
After commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"),
the mtu range for dummy device becomes [68, 1500].
This patch extends it to [0, 65535].
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"),
mtu range is checked at dev_set_mtu().
This patch adds min_mtu for nlmon device and remove unnecessary
ndo_change_mtu() function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3e3aaf649416 ("phy: fix mdiobus module safety") fixed the way we
dealt with MDIO bus module reference count, but sort of introduced a
regression in that, if an Ethernet driver registers its own MDIO bus
driver, as is common, we will end up with the Ethernet driver's
module->refnct set to 1, thus preventing this driver from any removal.
Fix this by comparing the network device's device driver owner against
the MDIO bus driver owner, and only if they are different, increment the
MDIO bus module refcount.
Fixes: 3e3aaf649416 ("phy: fix mdiobus module safety")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When free macvlan_port in macvlan_port_destroy, it is safe to free
directly because netdev_rx_handler_unregister could enforce one
grace period.
So it is unnecessary to use kfree_rcu for macvlan_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two functions which would free the ipvl_port now. The first
is ipvlan_port_create. It frees the ipvl_port in the error handler,
so it could kfree it directly. The second is ipvlan_port_destroy. It
invokes netdev_rx_handler_unregister which enforces one grace period
by synchronize_net firstly, so it also could kfree the ipvl_port
directly and safely.
So it is unnecessary to use kfree_rcu to free ipvl_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following warnings:
drivers/pci/host/vmd.c:731:12: warning: ‘vmd_suspend’ defined but not used [-Wunused-function]
static int vmd_suspend(struct device *dev)
^
drivers/pci/host/vmd.c:739:12: warning: ‘vmd_resume’ defined but not used [-Wunused-function]
static int vmd_resume(struct device *dev)
^
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
SRCU lets synchronize_srcu() depend on VMD-local RCU primitives, preventing
long delays from locking up RCU in other systems. VMD performs a
synchronize when removing a device, but will hit all IRQ lists if the
device uses all VMD vectors. This patch will not help VMD's RCU
synchronization, but will isolate the read side delays to the VMD
subsystem. Additionally, the use of SRCU in VMD's ISR will keep it
isolated from any other RCU waiters in the rest of the system.
Tested using concurrent FIO and NVMe resets:
[global]
rw=read
bs=4k
direct=1
ioengine=libaio
iodepth=32
norandommap
timeout=300
runtime=1000000000
[nvme0]
cpus_allowed=0-63
numjobs=8
filename=/dev/nvme0n1
[nvme1]
cpus_allowed=0-63
numjobs=8
filename=/dev/nvme1n1
while (true) do
for i in /sys/class/nvme/nvme*; do
echo "Resetting ${i##*/}"
echo 1 > $i/reset_controller;
sleep 5
done;
done
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.
For older releases, hard code a fixed reduced value. For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for setting the RGMII_IDMODE bit was added in the commit
referenced below. However, that commit did not add the symmetrical
clearing of the bit by way of setting it in "mask". Add it here.
Note that the documentation marks clearing this bit as "reserved",
however, according to TI, support for delaying the clock does exist in
the MAC, although it is not officially supported.
We tested this on a board with an RGMII to RGMII link that will not
work unless this bit is cleared.
Fixes: 0fb26c3063ea ("drivers: net: cpsw-phy-sel: add support to configure rgmii internal delay")
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From what I can tell, spin_lock(&priv->lock) is not needed, since the
phy_ethtool_ksettings_set call is not given the priv struct.
phy_start_aneg takes the phydev->lock. Calls to phy_adjust_link
from phy_state_machine also takes the phydev->lock.
[ 13.718319] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
[ 13.726717] in_atomic(): 1, irqs_disabled(): 0, pid: 1307, name: ethtool
[ 13.742115] Hardware name: Axis ARTPEC-6 Platform
[ 13.746829] [<80110568>] (unwind_backtrace) from [<8010c2bc>] (show_stack+0x18/0x1c)
[ 13.754575] [<8010c2bc>] (show_stack) from [<80433484>] (dump_stack+0x80/0xa0)
[ 13.761801] [<80433484>] (dump_stack) from [<80145428>] (___might_sleep+0x108/0x170)
[ 13.769554] [<80145428>] (___might_sleep) from [<806c9b50>] (mutex_lock+0x24/0x44)
[ 13.777128] [<806c9b50>] (mutex_lock) from [<8050cbc0>] (phy_start_aneg+0x1c/0x13c)
[ 13.784783] [<8050cbc0>] (phy_start_aneg) from [<8050d338>] (phy_ethtool_ksettings_set+0x98/0xd0)
[ 13.793656] [<8050d338>] (phy_ethtool_ksettings_set) from [<80517adc>] (stmmac_ethtool_set_link_ksettings+0xa0/0xb4)
[ 13.804184] [<80517adc>] (stmmac_ethtool_set_link_ksettings) from [<805c5138>] (ethtool_set_settings+0xd4/0x13c)
[ 13.814358] [<805c5138>] (ethtool_set_settings) from [<805c9718>] (dev_ethtool+0x13c4/0x211c)
[ 13.822882] [<805c9718>] (dev_ethtool) from [<805dc7c0>] (dev_ioctl+0x480/0x8e0)
[ 13.830291] [<805dc7c0>] (dev_ioctl) from [<80260e34>] (do_vfs_ioctl+0x94/0xa00)
[ 13.837699] [<80260e34>] (do_vfs_ioctl) from [<802617dc>] (SyS_ioctl+0x3c/0x60)
[ 13.845011] [<802617dc>] (SyS_ioctl) from [<801088bc>] (__sys_trace_return+0x0/0x10)
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Tegra PCI host controller driver no longer relies on any of the 32-bit
ARM glue for PCI, so it can be enabled on 64-bit configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
|
The PCIe host controller found on Tegra X1 is very similar to its
predecessor on Tegra K1. A bug was introduced in the new revision that
is worked around by always enabling the performance counter, otherwise
accesses to configuration space will block for a number of seconds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
|
Tegra210's PCIe controller has a bug that requires the PCA (performance
counter) feature to be enabled. If this isn't done, accesses to device
configuration space will hang the chip for tens of seconds. Implement the
workaround.
Based on commit 514e19138af2 ("pci: tegra: implement PCA enable
workaround") from U-Boot by Stephen Warren <swarren@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
|
Tegra is one of the remaining platforms that still use the traditional
pci_common_init_dev() interface for probing PCI host bridges.
This demonstrates how to convert it to the pci_register_host interface I
just added in a previous patch. This leads to a more linear probe sequence
that can handle errors better because we avoid callbacks into the driver,
and it makes the driver architecture independent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
|
Allow PCI host bridge drivers to use the new host bridge interfaces to
register their host bridge.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
|
Provide a way to allocate driver-specific data along with a PCI host bridge
structure. The bridge's ->private field points to this data.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
|
Make the existing pci_host_bridge structure a proper device that is usable
by PCI host drivers in a more standard way. In addition to the existing
pci_scan_bus(), pci_scan_root_bus(), pci_scan_root_bus_msi(), and
pci_create_root_bus() interfaces, this unfortunately means having to add
yet another interface doing basically the same thing, and add some extra
code in the initial step.
However, this time it's more likely to be extensible enough that we won't
have to do another one again in the future, and we should be able to reduce
code much more as a result.
The main idea is to pull the allocation of 'struct pci_host_bridge' out of
the registration, and let individual host drivers and architecture code
fill the members before calling the registration function.
There are a number of things we can do based on this:
* Use a single memory allocation for the driver-specific structure
and the generic PCI host bridge
* consolidate the contents of driver-specific structures by moving
them into pci_host_bridge
* Add a consistent interface for removing a PCI host bridge again
when unloading a host driver module
* Replace the architecture specific __weak pcibios_*() functions with
callbacks in a pci_host_bridge device
* Move common boilerplate code from host drivers into the generic
function, based on contents of the structure
* Extend pci_host_bridge with additional members when needed without
having to add arguments to pci_scan_*().
* Move members of struct pci_bus into pci_host_bridge to avoid
having lots of identical copies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
|
We can't just reuse pci_remove as there may be userspace still
doing things.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98638
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97980
Reviewed-by: Christian König <christian.koenig@amd.com>
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The CPTS drivers uses 8sec period for overflow checking with
assumption that CPTS retclk will not exceed 500MHz. But that's not
true on some TI platforms (Kesytone 2). As result, it is possible that
CPTS counter will overflow more than once between two readings.
Hence, fix it by selecting overflow check period dynamically as
max_sec_before_overflow/2, where
max_sec_before_overflow = max_counter_val / rftclk_freq.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cyclecounter mult and shift values can be calculated based on the
CPTS rfclk frequency and timekeepnig framework provides required algos
and API's.
Hence, calc mult and shift basing on CPTS rfclk frequency if both
cpts_clock_shift and cpts_clock_mult properties are not provided in DT (the
basis of calculation algorithm is borrowed from
__clocksource_update_freq_scale() commit 7d2f944a2b83 ("clocksource:
Provide a generic mult/shift factor calculation")). After this change
cpts_clock_shift and cpts_clock_mult DT properties will become optional.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move DT properties parsing into CPTS driver to simplify CPSW
code and CPTS driver porting on other SoC in the future
(like Keystone 2) - with this change it will not be required
to add the same DT parsing code in Keystone 2 NETCP driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation CPTS initialization and deinitialization
(represented by cpts_register/unregister()) does too many static
initialization from .ndo_open(), which is reasonable to do once at probe
time instead, and also require caller to allocate memory for struct cpts,
which is internal for CPTS driver in general.
This patch splits CPTS initialization and deinitialization on two parts:
- static initializtion cpts_create()/cpts_release() which expected to be
executed when parent driver is probed/removed;
- dynamic part cpts_register/unregister() which expected to be executed
when network device is opened/closed.
As result, current code of CPTS parent driver - CPSW - will be simplified
(and it also will allow simplify adding support for Keystone 2 devices in
the future), plus more initialization errors will be catched earlier. In
addition, this change allows to clean up cpts.h for the case when CPTS is
disabled.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPTS module and IRQs are always enabled when CPTS is registered,
before starting overflow check work, and disabled during
deregistration, when overflow check work has been canceled already.
So, It doesn't require to (re)enable CPTS module and IRQs in
cpts_overflow_check().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a CPTS user does not exit gracefully by disabling cpts
timestamping and leaving a joined multicast group, the system
continues to receive and timestamps the ptp packets which eventually
occupy all the event list entries. When this happns, the added code
tries to remove some list entries which are expired.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpts now is left enabled after unregistration.
Hence, disable it in cpts_unregister().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ptp clock registered before spinlock, which is protecting it, and
before timecounter and cyclecounter initialization in cpts_register().
So, ensure that ptp clock is registered the last, after everything
else is done.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
