| Age | Commit message (Collapse) | Author |
|---|
|
Add RGMII TX/RX delay configuration support. RGMII standard requires 2ns
delay to help the RGMII bridge receiver to sample data correctly. If the
default value does not provide proper centering of the data sample, the
TX/RX delay parameters can be used to adjust accordingly.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Other callers of udp_tunnel6_xmit_skb just pass 0 for the prio
argument. Jesse Gross <jesse@nicira.com> suggested that prio is really
the same as IPv4's tos and should be handled the same, so this is my
interpretation of that suggestion.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jesse Gross <jesse@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NOTE: Link-local IPv6 addresses for remote endpoints are not supported,
since the driver currently has no capacity for binding a geneve
interface to a specific link.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the pxa2xx_spi_acpi_get_pdata() so that it can create platform data
also on platforms that do not support ACPI or if CONFIG_ACPI is not set.
Now it is expected that "pxa2xx-spi" platform device is either created with
explicit platform data or has an ACPI companion device.
However there is only little in pxa2xx_spi_acpi_get_pdata() that is really
dependent on ACPI companion and it can be reworked to cover also cases
where "pxa2xx-spi" device doesn't have ACPI companion and is created
without platform data.
Do this by renaming the pxa2xx_spi_acpi_get_pdata(), moving it outside of
CONFIG_ACPI test and changing a few runtime tests there to support non-ACPI
case. Only port/bus ID setting based on ACPI _UID is dependent on ACPI and
is moved to own function inside CONFIG_ACPI.
Purpose of this to support non-ACPI case for those PCI enumerated compound
devices that integrate both LPSS SPI host controller and integrated DMA
engine under the same PCI ID and which are registered in MFD layer instead
of in spi-pxa2xx-pci.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
LPSS SPI in Intel Broxton is otherwise the same than in Intel Sunrisepoint
but it supports up to four chip selects per port and has different FIFO
thresholds. Patch adds support for two Broxton SoC variants.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SPI capabilities register located in private registers space of newer
Intel LPSS SPI host controllers tell in register bits 12:9 which chip
select signals are enabled.
Use that information for detecting the number of chip selects. For
simplicity we assume chip selects are enabled one after another without
disabled chip selects between. For instance CS0 | CS1 | CS2 but not
CS0 | CS1 | CS3.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Intel LPSS SPI host controllers in upcoming Intel platforms can have up
to 4 chip selects per port. Extend chip select control in
lpss_ssp_cs_control() by adding a code that selects the active chip
select output prior to changing the state. Detection for number of
enabled chip select signals will be added by another patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename a few defines that are specific to Intel LPSS SPI private
registers with LPSS prefix. It makes easier to distinguish them from
common defines.
Suggested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit bfebd1cdb497a57757c83f5fbf1a29931591e2a4 ("dm: add full blk-mq
support to request-based DM") moves the initialization of the fields
backing_dev_info.congested_fn, backing_dev_info.congested_data and
queuedata from the function dm_init_md_queue (that is called when the
device is created) to dm_init_old_md_queue (that is called after the
device type is determined).
There is no locking when accessing these variables, thus it is possible
for other parts of the kernel to briefly see this data in a transient
state (e.g. queue->backing_dev_info.congested_fn initialized and
md->queue->backing_dev_info.congested_data uninitialized, resulting in
passing an incorrect parameter to the function dm_any_congested).
This queue data is left initialized for blk-mq devices even though they
that don't use it.
Fixes: bfebd1cdb497 ("dm: add full blk-mq support to request-based DM")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v4.1+
|
|
LS1043a and LS2080A in the Layerscape family also support DSPI, make
DSPI selectable for these hardwares.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
there's no need to call pm_runtime_get_sync()
followed by pm_runtime_put(). We should, instead,
just call pm_runtime_put_sync() and pm_runtime_disable().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
Few more drm-misc stragglers for 4.4. Big thing is the generic probe for
imx/rockchip/armada (but the variant for msm/rpi/exynos is still missing).
Also the hdmi clocking fixes from Ville which was a lot of confusion about
which tree it should be applied to ;-)
* tag 'topic/drm-misc-2015-10-22' of git://anongit.freedesktop.org/drm-intel:
drm: correctly check failed allocation
vga_switcheroo: Constify vga_switcheroo_handler
drm/armada: Convert the probe function to the generic drm_of_component_probe()
drm/rockchip: Convert the probe function to the generic drm_of_component_probe()
drm/imx: Convert the probe function to the generic drm_of_component_probe()
drm: Introduce generic probe function for component based masters.
drm/edid: Round to closest when computing the CEA/HDMI alternate clock
drm/edid: Fix up clock for CEA/HDMI modes specified via detailed timings
|
|
into drm-next
More amdgpu and radeon stuff for drm-next. Stoney support is the big change.
The rest is just bug fixes and code cleanups. The Stoney stuff is pretty
low impact with respect to existing chips.
* 'drm-next-4.4' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: change VM size default to 64GB
drm/amdgpu: add Stoney pci ids
drm/amdgpu: update the core VI support for Stoney
drm/amdgpu: add VCE support for Stoney (v2)
drm/amdgpu: add UVD support for Stoney
drm/amdgpu: add GFX support for Stoney (v2)
drm/amdgpu: add SDMA support for Stoney (v2)
drm/amdgpu: add DCE support for Stoney
drm/amdgpu: Update SMC/DPM for Stoney
drm/amdgpu: add GMC support for Stoney
drm/amdgpu: add Stoney chip family
drm/amdgpu: fix the broken vm->mutex V2
drm/amdgpu: remove the unnecessary parameter adev for amdgpu_fence_wait_any()
drm/amdgpu: remove the exclusive lock
drm/amdgpu: remove old lockup detection infrastructure
drm: fix trivial typos
drm/amdgpu/dce: simplify suspend/resume
drm/amdgpu/gfx8: set TC_WB_ACTION_EN in RELEASE_MEM packet
drm/radeon: Use rdev->gem.mutex to protect hyperz/cmask owners
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
Bunch of -fixes for 4.4. Well not just, I've left the mmio/register work
from Ville in here since it's low-risk but lots of churn all over.
* tag 'drm-intel-next-fixes-2015-10-22' of git://anongit.freedesktop.org/drm-intel: (23 commits)
drm/i915: Use round to closest when computing the CEA 1.001 pixel clocks
drm/i915: Kill the leftover RMW from ivb_sprite_disable()
drm/i915: restore ggtt double-bind avoidance
drm/i915/skl: Enable pipe gamma for sprite planes.
drm/i915/skl+: Enable pipe CSC on cursor planes. (v2)
MAINTAINERS: add link to the Intel Graphics for Linux web site
drm/i915: Move skl/bxt gt specific workarounds to ring init
drm/i915: Drop i915_gem_obj_is_pinned() from set-cache-level
drm/i915: revert a few more watermark commits
drm/i915: Remove dev_priv argument from NEEDS_FORCE_WAKE
drm/i915: Clean up LVDS register handling
drm/i915: Throw out some useless variables
drm/i915: Parametrize and fix SWF registers
drm/i915: s/PIPE_FRMCOUNT_GM45/PIPE_FRMCOUNT_G4X/ etc.
drm/i915: Turn GEN5_ASSERT_IIR_IS_ZERO() into a function
drm/i915: Fix a few bad hex numbers in register defines
drm/i915: Protect register macro arguments
drm/i915: Include gpio_mmio_base in GMBUS reg defines
drm/i915: Parametrize HSW video DIP data registers
drm/i915: Eliminate weird parameter inversion from BXT PPS registers
...
|
|
into drm-fixes
regression fix for backlight on old laptops.
* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix dpms when driver backlight control is disabled
drm/radeon: move bl encoder assignment into bl init
|
|
An Enhanced Allocation Capability entry with BEI 0 fills in
dev->resource[0] just like a real BAR 0 would, but non-EA experts might not
connect "EA - BEI 0" with BAR 0.
Decode the EA jargon a little bit, e.g., change this:
pci 0002:01:00.0: EA - BEI 0, Prop 0x00: [mem 0x84300000-0x84303fff]
to this:
pci 0002:01:00.0: BAR 0: [mem 0x84300000-0x84303fff] (from Enhanced Allocation, properties 0x00)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Expand bitmask #defines completely. This puts the shift in the code
instead of in the #define, but it makes it more obvious in the header file
how fields in the register are laid out.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
SR-IOV BARs can be specified via EA entries. Extend the EA parser to
extract the SRIOV BAR resources, and modify sriov_init() to use resources
previously obtained via EA.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean O. Stalley <sean.stalley@intel.com>
|
|
Add support for devices using Enhanced Allocation entries instead of BARs.
This allows the kernel to parse the EA Extended Capability structure in PCI
config space and claim the BAR-equivalent resources.
See https://pcisig.com/sites/default/files/specification_documents/ECN_Enhanced_Allocation_23_Oct_2014_Final.pdf
[bhelgaas: add spec URL, s/pci_ea_set_flags/pci_ea_flags/, consolidate
declarations, print unknown property in hex to match spec]
Signed-off-by: Sean O. Stalley <sean.stalley@intel.com>
[david.daney@cavium.com: Add more support/checking for Entry Properties,
allow EA behind bridges, rewrite some error messages.]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The new Enhanced Allocation (EA) capability support (patches to follow)
creates resources with the IORESOURCE_PCI_FIXED set. During resource
assignment in pci_bus_assign_resources(), IORESOURCE_PCI_FIXED resources
are not given a parent. This, in turn, causes pci_enable_resources() to
fail with a "not claimed" error.
So, in __pci_bus_assign_resources(), for IORESOURCE_PCI_FIXED resources,
try to request the resource from a parent bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean O. Stalley <sean.stalley@intel.com>
|
|
The new Enhanced Allocation (EA) capability support (patches to follow)
creates resources with the IORESOURCE_PCI_FIXED set. Since these resources
cannot be relocated or resized, their alignment is not really defined, and
it is therefore not specified. This causes a problem in pbus_size_mem()
where resources with unspecified alignment are disabled.
So, in pbus_size_mem() skip IORESOURCE_PCI_FIXED resources, instead of
disabling them.
[bhelgaas: folded in "flags & IORESOURCE_PCI_FIXED" fix from David]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean O. Stalley <sean.stalley@intel.com>
|
|
The return value should be checked for non-zero, instead
of checking it being IS_ERR_VALUE().
Acked-by: Alan Tull <atull@opensource.altera.com>
Reviewed-by: Josh Cartwright <joshc@eso.teric.us>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Previously, we read, validated, and cached PCI_SRIOV_VF_OFFSET and
PCI_SRIOV_VF_STRIDE in sriov_enable(). But sriov_init() now does
that via compute_max_vf_buses(), so we don't need to do it again.
Remove the PCI_SRIOV_VF_OFFSET and PCI_SRIOV_VF_STRIDE config reads from
sriov_enable(). The pci_sriov structure already contains the offset and
stride corresponding to the current NumVFs.
[bhelgaas: split to separate patch for reviewability]
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wei Yang <weiyang@linux.vnet.ibm.com>
|
|
The enumeration path should leave NumVFs set to zero. But after
4449f079722c ("PCI: Calculate maximum number of buses required for VFs"),
we call virtfn_max_buses() in the enumeration path, which changes NumVFs.
This NumVFs change is visible via lspci and sysfs until a driver enables
SR-IOV.
Iterate from TotalVFs down to zero so NumVFs is zero when we're finished
computing the maximum number of buses. Validate offset and stride in
the loop, so we can test it at every possible NumVFs setting. Rename
virtfn_max_buses() to compute_max_vf_buses() to hint that it does have a
side effect of updating iov->max_VF_buses.
[bhelgaas: changelog, rename, allow numVF==1 && stride==0, rework loop,
reverse sense of error path]
Fixes: 4449f079722c ("PCI: Calculate maximum number of buses required for VFs")
Based-on-patch-by: Ethan Zhao <ethan.zhao@oracle.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
For some SR-IOV devices, the number of available virtual functions, i.e.,
TotalVFs, increases after setting the ARI Capable Hierarchy bit in the
SR-IOV Control register. This violates the SR-IOV spec, r1.1, sec 3.3.6,
which says TotalVFs is HwInit, but we don't need TotalVFs before setting
the ARI Capable bit anyway.
Set the ARI Capable Hierarchy bit (if ARI is enabled in the upstream
bridge) before reading TotalVFs.
[bhelgaas: changelog]
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
No callers and no providers left, go ahead and remove it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The driver does not support it anyway, and the support
should be added to a generic layer shared by both hfi1,
qib and softroce drivers.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The driver does not support it anyway, and the support
should be added to a generic layer shared by both hfi1,
qib and softroce drivers.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
If driver backlight control is disabled, either by driver
parameter or default per-asic setting, revert to the old behavior.
Fixes a regression in commit:
4281f46ef839050d2ef60348f661eb463c21cc2e
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
So that the bl encoder will be null if the GPU does not
control the backlight.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This supports a way to get target stats through normal
ethtool stats API.
For instance:
# ethtool -S wlan1
NIC statistics:
tx_pkts_nic: 353
tx_bytes_nic: 25142
rx_pkts_nic: 6
rx_bytes_nic: 996
d_tx_ucast_pkts: 89
d_tx_bcast_pkts: 264
d_tx_ucast_bytes: 3020
d_tx_bcast_bytes: 22122
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This will allow us to call it from elsewhere when implementing
ethtool stats.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Improper use of strlcpy caused garbage to be appended to the
firmware version string. Fix this by paying attention to the
ie_lenth.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It can take a user a while to understand why their
NIC that advertises 802.11n support cannot actually
do 802.11n. Print out a warning in the logs to save
the next poor person to use this NIC some trouble.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This lets 'iw phy phy0 info' report antennas for
the radio device:
...
Available Antennas: TX 0x2 RX 0x2
Configured Antennas: TX 0x2 RX 0x2
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When configuring Tx vring for new connection,
WMI call to the firmware may fail. In this case, need to
clean up properly. In particular, need to call
cfg80211_del_sta() in case of AP like interface.
Perform full "disconnect" procedure for proper clean up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:
- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When Tx ring full is encountered with TSO,
printout of "DMA error" was wrongly printed.
In addition, in case of Tx ring full return
proper error code so that NETDEV_TX_BUSY is
returned to network stack in order not to
drop the packets and retry transmission of the
packets when ring is emptied.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Some events are ignored for purpose; such events should not
be treated as "unhandled events". Replace info message
saying "unhandled" with debug one saying "ignore", to reduce
dmesg pollution
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add the hardware name, revision and update the pci_id table.
Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.
QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
To reflect configured antenna settings in HT/VHT MCS map,
reload the HT/VHT capabilities upon antenna change.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Move HT and VHT capabiltity setup static functions to avoid
forward declaration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
HT/VHT MCS rateset should be filled only for configured chainmask
rather that max supported chainmask. Fix that by checking configured
chainmask while filling HT/VHT MCS rate map.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Removing supported chainmask fields as it can be always derived
from num_rf_chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This patch adds support for getting firmware debug stats in 10.4 fw.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
