| Age | Commit message (Collapse) | Author |
|---|
|
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
If the port is going to send Discover_Identity Message, vdm_sm_running
flag was intentionally set before entering Ready States in order to
avoid the conflict because the port and the port partner might start
AMS at almost the same time after entering Ready States.
However, the original design has a problem. When the port is doing
DR_SWAP from Device to Host, it raises the flag. Later in the
tcpm_send_discover_work, the flag blocks the procedure of sending the
Discover_Identity and it might never be cleared until disconnection.
Since there exists another flag send_discover representing that the port
is going to send Discover_Identity or not, it is enough to use that flag
to prevent the conflict. Also change the timing of the set/clear of
vdm_sm_running to indicate whether the VDM SM is actually running or
not.
Fixes: c34e85fa69b9 ("usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work")
Cc: stable <stable@vger.kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210826124201.1562502-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The recent attempt to handle an unknown ROM state in the commit
d143825baf15 ("usb: renesas-xhci: Fix handling of unknown ROM state")
resulted in a regression and reverted later by the commit 44cf53602f5a
("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"").
The problem of the former fix was that it treated the failure of
firmware loading as a fatal error. Since the firmware files aren't
included in the standard linux-firmware tree, most users don't have
them, hence they got the non-working system after that. The revert
fixed the regression, but also it didn't make the firmware loading
triggered even on the devices that do need it. So we need still a fix
for them.
This is another attempt to handle the unknown ROM state. Like the
previous fix, this also tries to load the firmware when ROM shows
unknown state. In this patch, however, the failure of a firmware
loading (such as a missing firmware file) isn't handled as a fatal
error any longer when ROM has been already detected, but it falls back
to the ROM mode like before. The error is returned only when no ROM
is detected and the firmware loading failed.
Along with it, for simplifying the code flow, the detection and the
check of ROM is factored out from renesas_fw_check_running() and done
in the caller side, renesas_xhci_check_request_fw(). It avoids the
redundant ROM checks.
The patch was tested on Lenovo Thinkpad T14 gen (BIOS 1.34). Also it
was confirmed that no regression is seen on another Thinkpad T14
machine that has worked without the patch, too.
Fixes: 44cf53602f5a ("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1189207
Link: https://lore.kernel.org/r/20210826124127.14789-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
zynq_qspi_exec_mem_op not interruptible
The function wait_for_completion_interruptible_timeout will return
-ERESTARTSYS immediately when receiving SIGKILL signal which is sent
by "jffs2_gcd_mtd" during umounting jffs2. This will break the SPI memory
operation because the data transmitting may begin before the command or
address transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210826005930.20572-1-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Oltean <vladimir.oltean@nxp.com>:
The ls-extirq irqchip driver accesses regmap inside its implementation
of the struct irq_chip :: irq_set_type method, and currently regmap
only knows to lock using normal spinlocks. But the method above wants
raw spinlock context, so this isn't going to work and triggers a
"[ BUG: Invalid wait context ]" splat.
The best we can do given the arrangement of the code is to patch regmap
and the syscon driver: regmap to support raw spinlocks, and syscon to
request them on behalf of its ls-extirq consumer.
Link: https://lore.kernel.org/lkml/20210825135438.ubcuxm5vctt6ne2q@skbuf/T/#u
Vladimir Oltean (2):
regmap: teach regmap to use raw spinlocks if requested in the config
mfd: syscon: request a regmap with raw spinlocks for some devices
drivers/base/regmap/internal.h | 4 ++++
drivers/base/regmap/regmap.c | 35 +++++++++++++++++++++++++++++-----
drivers/mfd/syscon.c | 16 ++++++++++++++++
include/linux/regmap.h | 2 ++
4 files changed, 52 insertions(+), 5 deletions(-)
--
2.25.1
base-commit: 6efb943b8616ec53a5e444193dccf1af9ad627b5
|
|
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb0147364850 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so")
Cc: <stable@vger.kernel.org>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
arm/fixes
Reset controller fixes for v5.14
Hide the Sparx5 reset driver unless the ARCH_SPARX5 or COMPILE_TEST
options are enabled, to avoid unnecessarily asking users about this
driver. Fix a return value argument type in the ZynqMP reset driver.
* tag 'reset-fixes-for-v5.14' of git://git.pengutronix.de/pza/linux:
reset: reset-zynqmp: Fixed the argument data type
reset: RESET_MCHP_SPARX5 should depend on ARCH_SPARX5
Link: https://lore.kernel.org/r/e543959c5b5ee7b25686f81049bf187d602daeda.camel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
Fixes: c4233573f6ee ("usb: dwc3: gadget: prepare TRBs on update transfers too")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e91e975affb0d0d02770686afc3a5b9eb84409f6.1629335416.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drm_dp_dpcd_read/write already has debug error message.
Drop redundant error messages which gives false
status even if correct value is read in drm_dp_dpcd_read().
v2: -Added fixes tag (Ankit)
v3: -Fixed build error (CI)
Fixes: 9488a030ac91 ("drm/i915: Add support for enabling link status and recovery")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.12+
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812131107.5531-1-swati2.sharma@intel.com
(cherry picked from commit b6dfa416172939edaa46a5a647457b94c6d94119)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
A small race exists between intel_gt_retire_requests_timeout and
intel_timeline_exit which could result in the syncmap not getting
free'd. Rather than work to hard to seal this race, simply cleanup the
syncmap on fini.
unreferenced object 0xffff88813bc53b18 (size 96):
comm "gem_close_race", pid 5410, jiffies 4294917818 (age 1105.600s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 0a 00 00 00 ................
00 00 00 00 00 00 00 00 6b 6b 6b 6b 06 00 00 00 ........kkkk....
backtrace:
[<00000000120b863a>] __sync_alloc_leaf+0x1e/0x40 [i915]
[<00000000042f6959>] __sync_set+0x1bb/0x240 [i915]
[<0000000090f0e90f>] i915_request_await_dma_fence+0x1c7/0x400 [i915]
[<0000000056a48219>] i915_request_await_object+0x222/0x360 [i915]
[<00000000aaac4ee3>] i915_gem_do_execbuffer+0x1bd0/0x2250 [i915]
[<000000003c9d830f>] i915_gem_execbuffer2_ioctl+0x405/0xce0 [i915]
[<00000000fd7a8e68>] drm_ioctl_kernel+0xb0/0xf0 [drm]
[<00000000e721ee87>] drm_ioctl+0x305/0x3c0 [drm]
[<000000008b0d8986>] __x64_sys_ioctl+0x71/0xb0
[<0000000076c362a4>] do_syscall_64+0x33/0x80
[<00000000eb7a4831>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Fixes: 531958f6f357 ("drm/i915/gt: Track timeline activeness in enter/exit")
Cc: <stable@vger.kernel.org>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730195342.110234-1-matthew.brost@intel.com
(cherry picked from commit faf890985e30d5e88cc3a7c50c1bcad32f89ab7c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
ADI r3p0 is used on SC9863 and UMS512 SoCs.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20210826091549.2138125-3-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use 50ms as default timeout value and the time clock is 32768HZ.
The original value of WDG_LOAD_VAL is not correct, so this patch
fixes it.
Fixes: ac1775012058 ("spi: sprd: Add the support of restarting the system")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20210826091549.2138125-2-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some drivers might access regmap in a context where a raw spinlock is
held. An example is drivers/irqchip/irq-ls-extirq.c, which calls
regmap_update_bits() from struct irq_chip :: irq_set_type, which is a
method called by __irq_set_trigger() under the desc->lock raw spin lock.
Since desc->lock is a raw spin lock and the regmap internal lock for
mmio is a plain spinlock (which can become sleepable on RT), this is an
invalid locking scheme and we get a splat stating that this is a
"[ BUG: Invalid wait context ]".
It seems reasonable for regmap to have an option use a raw spinlock too,
so add that in the config such that drivers can request it.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210825205041.927788-2-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Traffic schedules can only be started up to eight seconds within the
future. Therefore, the driver periodically checks every two seconds whether the
admin base time provided by the user is inside that window. If so the schedule
is started. Otherwise the check is deferred.
However, according to the programming manual the look ahead window size should
be four - not eight - seconds. By using the proposed value of four seconds
starting a schedule at a specified admin base time actually works as expected.
Fixes: 24dfc6eb39b2 ("net: dsa: hellcreek: Add TAPRIO offloading support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the gate control list which is programmed into the hardware is
incorrect resulting in wrong traffic schedules. The problem is the loop
variables are incremented before they are referenced. Therefore, move the
increment to the end of the loop.
Fixes: 24dfc6eb39b2 ("net: dsa: hellcreek: Add TAPRIO offloading support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.
Fixes: 5b377d114f2b ("cxgb4: Add debugfs facility to inject FL starvation")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
and TX error counters
This patch fixes the interchanged fetch of the CAN RX and TX error
counters from the ESD_EV_CAN_ERROR_EXT message. The RX error counter
is really in struct rx_msg::data[2] and the TX error counter is in
struct rx_msg::data[3].
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/20210825215227.4947-2-stefan.maetje@esd.eu
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
drivers/net/usb/asix_devices.c:757:60-65: WARNING: conversion to bool not needed here
Remove unneeded conversion to bool
Semantic patch information:
Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unneeded.
Generated by: scripts/coccinelle/misc/boolconv.cocci
Fixes: 7a141e64cf14 ("net: usb: asix: ax88772: move embedded PHY detection as early as possible")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210825183538.13070-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
GENPD core doesn't support handling performance state changes while
consumer device is runtime-suspended or when runtime PM is disabled.
GENPD core may override performance state that was configured by device
driver while RPM of the device was disabled or device was RPM-suspended.
Let's close that gap by allowing drivers to control performance state
while RPM of a consumer device is disabled and to set up performance
state of RPM-suspended device that will be applied by GENPD core on
RPM-resume of the device.
Fixes: 5937c3ce2122 ("PM: domains: Drop/restore performance state votes for devices at runtime PM")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
|
|
vctrl_enable() and vctrl_disable() call regulator_enable() and
regulator_disable(), respectively. However, vctrl_* are regulator ops
and should not be calling the locked regulator APIs. Doing so results in
a lockdep warning.
Instead of exporting more internal regulator ops, model the ctrl supply
as an actual supply to vctrl-regulator. At probe time this driver still
needs to use the consumer API to fetch its constraints, but otherwise
lets the regulator core handle the upstream supply for it.
The enable/disable/is_enabled ops are not removed, but now only track
state internally. This preserves the original behavior with the ops
being available, but one could argue that the original behavior was
already incorrect: the internal state would not match the upstream
supply if that supply had another consumer that enabled the supply,
while vctrl-regulator was not enabled.
The lockdep warning is as follows:
WARNING: possible circular locking dependency detected
5.14.0-rc6 #2 Not tainted
------------------------------------------------------
swapper/0/1 is trying to acquire lock:
ffffffc011306d00 (regulator_list_mutex){+.+.}-{3:3}, at:
regulator_lock_dependent (arch/arm64/include/asm/current.h:19
include/linux/ww_mutex.h:111
drivers/regulator/core.c:329)
but task is already holding lock:
ffffff8004a77160 (regulator_ww_class_mutex){+.+.}-{3:3}, at:
regulator_lock_recursive (drivers/regulator/core.c:156
drivers/regulator/core.c:263)
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (regulator_ww_class_mutex){+.+.}-{3:3}:
__mutex_lock_common (include/asm-generic/atomic-instrumented.h:606
include/asm-generic/atomic-long.h:29
kernel/locking/mutex.c:103
kernel/locking/mutex.c:144
kernel/locking/mutex.c:963)
ww_mutex_lock (kernel/locking/mutex.c:1199)
regulator_lock_recursive (drivers/regulator/core.c:156
drivers/regulator/core.c:263)
regulator_lock_dependent (drivers/regulator/core.c:343)
regulator_enable (drivers/regulator/core.c:2808)
set_machine_constraints (drivers/regulator/core.c:1536)
regulator_register (drivers/regulator/core.c:5486)
devm_regulator_register (drivers/regulator/devres.c:196)
reg_fixed_voltage_probe (drivers/regulator/fixed.c:289)
platform_probe (drivers/base/platform.c:1427)
[...]
-> #1 (regulator_ww_class_acquire){+.+.}-{0:0}:
regulator_lock_dependent (include/linux/ww_mutex.h:129
drivers/regulator/core.c:329)
regulator_enable (drivers/regulator/core.c:2808)
set_machine_constraints (drivers/regulator/core.c:1536)
regulator_register (drivers/regulator/core.c:5486)
devm_regulator_register (drivers/regulator/devres.c:196)
reg_fixed_voltage_probe (drivers/regulator/fixed.c:289)
[...]
-> #0 (regulator_list_mutex){+.+.}-{3:3}:
__lock_acquire (kernel/locking/lockdep.c:3052 (discriminator 4)
kernel/locking/lockdep.c:3174 (discriminator 4)
kernel/locking/lockdep.c:3789 (discriminator 4)
kernel/locking/lockdep.c:5015 (discriminator 4))
lock_acquire (arch/arm64/include/asm/percpu.h:39
kernel/locking/lockdep.c:438
kernel/locking/lockdep.c:5627)
__mutex_lock_common (include/asm-generic/atomic-instrumented.h:606
include/asm-generic/atomic-long.h:29
kernel/locking/mutex.c:103
kernel/locking/mutex.c:144
kernel/locking/mutex.c:963)
mutex_lock_nested (kernel/locking/mutex.c:1125)
regulator_lock_dependent (arch/arm64/include/asm/current.h:19
include/linux/ww_mutex.h:111
drivers/regulator/core.c:329)
regulator_enable (drivers/regulator/core.c:2808)
vctrl_enable (drivers/regulator/vctrl-regulator.c:400)
_regulator_do_enable (drivers/regulator/core.c:2617)
_regulator_enable (drivers/regulator/core.c:2764)
regulator_enable (drivers/regulator/core.c:308
drivers/regulator/core.c:2809)
_set_opp (drivers/opp/core.c:819 drivers/opp/core.c:1072)
dev_pm_opp_set_rate (drivers/opp/core.c:1164)
set_target (drivers/cpufreq/cpufreq-dt.c:62)
__cpufreq_driver_target (drivers/cpufreq/cpufreq.c:2216
drivers/cpufreq/cpufreq.c:2271)
cpufreq_online (drivers/cpufreq/cpufreq.c:1488 (discriminator 2))
cpufreq_add_dev (drivers/cpufreq/cpufreq.c:1563)
subsys_interface_register (drivers/base/bus.c:?)
cpufreq_register_driver (drivers/cpufreq/cpufreq.c:2819)
dt_cpufreq_probe (drivers/cpufreq/cpufreq-dt.c:344)
[...]
other info that might help us debug this:
Chain exists of:
regulator_list_mutex --> regulator_ww_class_acquire --> regulator_ww_class_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(regulator_ww_class_mutex);
lock(regulator_ww_class_acquire);
lock(regulator_ww_class_mutex);
lock(regulator_list_mutex);
*** DEADLOCK ***
6 locks held by swapper/0/1:
#0: ffffff8002d32188 (&dev->mutex){....}-{3:3}, at:
__device_driver_lock (drivers/base/dd.c:1030)
#1: ffffffc0111a0520 (cpu_hotplug_lock){++++}-{0:0}, at:
cpufreq_register_driver (drivers/cpufreq/cpufreq.c:2792 (discriminator 2))
#2: ffffff8002a8d918 (subsys mutex#9){+.+.}-{3:3}, at:
subsys_interface_register (drivers/base/bus.c:1033)
#3: ffffff800341bb90 (&policy->rwsem){+.+.}-{3:3}, at:
cpufreq_online (include/linux/bitmap.h:285
include/linux/cpumask.h:405
drivers/cpufreq/cpufreq.c:1399)
#4: ffffffc011f0b7b8 (regulator_ww_class_acquire){+.+.}-{0:0}, at:
regulator_enable (drivers/regulator/core.c:2808)
#5: ffffff8004a77160 (regulator_ww_class_mutex){+.+.}-{3:3}, at:
regulator_lock_recursive (drivers/regulator/core.c:156
drivers/regulator/core.c:263)
stack backtrace:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.14.0-rc6 #2 7c8f8996d021ed0f65271e6aeebf7999de74a9fa
Hardware name: Google Scarlet (DT)
Call trace:
dump_backtrace (arch/arm64/kernel/stacktrace.c:161)
show_stack (arch/arm64/kernel/stacktrace.c:218)
dump_stack_lvl (lib/dump_stack.c:106 (discriminator 2))
dump_stack (lib/dump_stack.c:113)
print_circular_bug (kernel/locking/lockdep.c:?)
check_noncircular (kernel/locking/lockdep.c:?)
__lock_acquire (kernel/locking/lockdep.c:3052 (discriminator 4)
kernel/locking/lockdep.c:3174 (discriminator 4)
kernel/locking/lockdep.c:3789 (discriminator 4)
kernel/locking/lockdep.c:5015 (discriminator 4))
lock_acquire (arch/arm64/include/asm/percpu.h:39
kernel/locking/lockdep.c:438
kernel/locking/lockdep.c:5627)
__mutex_lock_common (include/asm-generic/atomic-instrumented.h:606
include/asm-generic/atomic-long.h:29
kernel/locking/mutex.c:103
kernel/locking/mutex.c:144
kernel/locking/mutex.c:963)
mutex_lock_nested (kernel/locking/mutex.c:1125)
regulator_lock_dependent (arch/arm64/include/asm/current.h:19
include/linux/ww_mutex.h:111
drivers/regulator/core.c:329)
regulator_enable (drivers/regulator/core.c:2808)
vctrl_enable (drivers/regulator/vctrl-regulator.c:400)
_regulator_do_enable (drivers/regulator/core.c:2617)
_regulator_enable (drivers/regulator/core.c:2764)
regulator_enable (drivers/regulator/core.c:308
drivers/regulator/core.c:2809)
_set_opp (drivers/opp/core.c:819 drivers/opp/core.c:1072)
dev_pm_opp_set_rate (drivers/opp/core.c:1164)
set_target (drivers/cpufreq/cpufreq-dt.c:62)
__cpufreq_driver_target (drivers/cpufreq/cpufreq.c:2216
drivers/cpufreq/cpufreq.c:2271)
cpufreq_online (drivers/cpufreq/cpufreq.c:1488 (discriminator 2))
cpufreq_add_dev (drivers/cpufreq/cpufreq.c:1563)
subsys_interface_register (drivers/base/bus.c:?)
cpufreq_register_driver (drivers/cpufreq/cpufreq.c:2819)
dt_cpufreq_probe (drivers/cpufreq/cpufreq-dt.c:344)
[...]
Reported-by: Brian Norris <briannorris@chromium.org>
Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking")
Fixes: e9153311491d ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20210825033704.3307263-3-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In commit e9153311491d ("regulator: vctrl-regulator: Avoid deadlock getting
and setting the voltage"), all calls to get/set the voltage of the
control regulator were switched to unlocked versions to avoid deadlocks.
However, the call in the probe path is done without regulator locks
held. In this case the locked version should be used.
Switch back to the locked regulator_get_voltage() in the probe path to
avoid any mishaps.
Fixes: e9153311491d ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20210825033704.3307263-2-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure a valid XSK buffer before proceed to free the xdp buffer.
The following kernel panic is observed without this patch:
RIP: 0010:xp_free+0x5/0x40
Call Trace:
stmmac_napi_poll_rxtx+0x332/0xb30 [stmmac]
? stmmac_tx_timer+0x3c/0xb0 [stmmac]
net_rx_action+0x13d/0x3d0
__do_softirq+0xfc/0x2fb
? smpboot_register_percpu_thread+0xe0/0xe0
run_ksoftirqd+0x32/0x70
smpboot_thread_fn+0x1d8/0x2c0
kthread+0x169/0x1a0
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
---[ end trace 0000000000000002 ]---
Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After free xsk_pool, there is possibility that napi polling is still
running in the middle, thus causes a kernel crash due to kernel NULL
pointer dereference of rx_q->xsk_pool and tx_q->xsk_pool.
Fix this by changing the XDP pool setup sequence to:
1. disable napi before free xsk_pool
2. enable napi after init xsk_pool
The following kernel panic is observed without this patch:
RIP: 0010:xsk_uses_need_wakeup+0x5/0x10
Call Trace:
stmmac_napi_poll_rxtx+0x3a9/0xae0 [stmmac]
__napi_poll+0x27/0x130
net_rx_action+0x233/0x280
__do_softirq+0xe2/0x2b6
run_ksoftirqd+0x1a/0x20
smpboot_thread_fn+0xac/0x140
? sort_range+0x20/0x20
kthread+0x124/0x150
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
---[ end trace a77c8956b79ac107 ]---
Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 2c896fb02e7f65299646f295a007bda043e0f382
"net: stmmac: dwmac-rk: add pd_gmac support for rk3399" and fixes
unbalanced pm_runtime_enable warnings.
In the commit to be reverted, support for power management was
introduced to the Rockchip glue code. Later, power management support
was introduced to the stmmac core code, resulting in multiple
invocations of pm_runtime_{enable,disable,get_sync,put_sync}.
The multiple invocations happen in rk_gmac_powerup and
stmmac_{dvr_probe, resume} as well as in rk_gmac_powerdown and
stmmac_{dvr_remove, suspend}, respectively, which are always called
in conjunction.
Fixes: 5ec55823438e850c91c6b92aec93fb04ebde29e2 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add tracing of interactions between the SCLP base driver, firmware and
other drivers to support problem determination in case of SCLP-related
issues.
For that purpose this patch introduces two new s390dbf debug areas:
- sclp: An abbreviated log of all common interactions
- sclp_err: A full log of failed or abnormal interactions
Tracing of full SCCB contents can be enabled for the sclp area by
setting its debug level to maximum (6).
Overview of added trace events:
* Firmware interaction:
- SRV1: Service call about to be issued
- SRV2: Service call was issued
- INT: Interrupt received
* Driver interaction:
- RQAD: Request was added
- RQOK: Request success
- RQAB: Request aborted
- RQTM: Request timed out
- REG: Event listener registered
- UREG: Event listener unregistered
- EVNT: Event callback
- STCG: State-change callback
* Abnormal events:
- TMO: A timeout occurred
- UNEX: Unexpected SCCB completion
* Other (not traced at default level):
- SYN1: Synchronous wait start
- SYN2: Synchronous wait end
Since the SCLP interface is used by console drivers this patch also
moves s390dbf printks outside the critical section protected by debug
area locks to prevent a potential deadlock that would otherwise be
introduced between console_owner --> sclp_lock --> sclp_debug.lock.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The 0day bot reported some kernel-doc warnings in this file so clean up
all of the kernel-doc and use proper kernel-doc formatting.
There are no more kernel-doc errors or warnings reported in this file.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Tony Krowiak <akrowiak@linux.ibm.com>
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Jason Herne <jjherne@linux.ibm.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: linux-s390@vger.kernel.org
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Link: https://lore.kernel.org/r/20210806050149.9614-1-rdunlap@infradead.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently zpci_dma_init_device()/zpci_dma_exit_device() is called as
part of zpci_enable_device()/zpci_disable_device() and errors for
zpci_dma_exit_device() are always ignored even if we could abort.
Improve upon this by moving zpci_dma_exit_device() out of
zpci_disable_device() and check for errors whenever we have a way to
abort the current operation. Note that for example in
zpci_event_hard_deconfigured() the device is expected to be gone so we
really can't abort and proceed even in case of error.
Similarly move the cc == 3 special case out of zpci_unregister_ioat()
and into the callers allowing to abort when finding an already disabled
devices precludes proceeding with the operation.
While we are at it log IOAT register/unregister errors in the s390
debugfs log,
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
As .remove() is only called after a successful .probe() call, we can
trust that the drvdata is valid.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The device struct provides a pointer for driver-private data. Use this
in the zcrypt drivers (as vfio_ap already does), and then remove the
custom pointer from the AP device structs.
As really_probe() will always clear the drvdata pointer on error, we
no longer have to do so ourselves.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The device struct itself already contains a pointer to its driver.
Use this consistently, instead of duplicating it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
This reverts commit 3c18e9baee0ef97510dcda78c82285f52626764b.
These devices do not appear to send a zero-length packet when the
transfer size is a multiple of the bulk-endpoint max-packet size. This
means that incoming data may not be processed by the driver until a
short packet is received or the receive buffer is full.
Revert back to using endpoint-sized receive buffers to avoid stalled
reads.
Reported-by: Paul Größel <pb.g@gmx.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214131
Fixes: 3c18e9baee0e ("USB: serial: ch341: fix character loss at high transfer rates")
Cc: stable@vger.kernel.org
Cc: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210824121926.19311-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
We found a hang, the steps to reproduce are as follows:
1. blocking device via scsi_device_set_state()
2. dd if=/dev/sda of=/mnt/t.log bs=1M count=10
3. echo none > /sys/block/sda/queue/scheduler
4. echo "running" >/sys/block/sda/device/state
Step 3 and 4 should complete after step 4, but they hang.
CPU#0 CPU#1 CPU#2
--------------- ---------------- ----------------
Step 1: blocking device
Step 2: dd xxxx
^^^^^^ get request
q_usage_counter++
Step 3: switching scheculer
elv_iosched_store
elevator_switch
blk_mq_freeze_queue
blk_freeze_queue
> blk_freeze_queue_start
^^^^^^ mq_freeze_depth++
> blk_mq_run_hw_queues
^^^^^^ can't run queue when dev blocked
> blk_mq_freeze_queue_wait
^^^^^^ Hang here!!!
wait q_usage_counter==0
Step 4: running device
store_state_field
scsi_rescan_device
scsi_attach_vpd
scsi_vpd_inquiry
__scsi_execute
blk_get_request
blk_mq_alloc_request
blk_queue_enter
^^^^^^ Hang here!!!
wait mq_freeze_depth==0
blk_mq_run_hw_queues
^^^^^^ dispatch IO, q_usage_counter will reduce to zero
blk_mq_unfreeze_queue
^^^^^ mq_freeze_depth--
To fix this, we need to run queue before rescanning device when the device
state changes to SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210824025921.3277629-1-lijinlin3@huawei.com
Fixes: f0f82e2476f6 ("scsi: core: Fix capacity set to zero after offlinining device")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Li Jinlin <lijinlin3@huawei.com>
Signed-off-by: Qiu Laibin <qiulaibin@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Without suspend/resume callbacks, the PHY cannot be powered down/up
administratively.
Fixes: e40d2cca0189 ("net: phy: add MediaTek Gigabit Ethernet PHY driver")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210823044422.164184-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Davinci needs to configure chipselect on transfer.
Fixes: 4a07b8bcd503 ("spi: bitbang: Make chipselect callback optional")
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Link: https://lore.kernel.org/r/735fb7b0-82aa-5b9b-85e4-53f0c348cc0e@nokia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
RD_CMD can accept slave address offset only, higher bits are reserved.
Writing the whole slave address including slave base seems unnecessary.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20210824070212.2089255-3-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The slave register offset shouldn't equal to the max slave address
which ADI can support to access.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20210824070212.2089255-2-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The register offset would be added a physical address base and then pass to
the function sprd_adt_read()/_write() each time before calling them. So we
can do that within these two functions instead, that would make the code
more clear.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20210824070212.2089255-1-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull rdma fixes from Jason Gunthorpe:
"Several small fixes, the first three are significant:
- mlx5 crash unloading drivers with a rare HW config
- missing userspace reporting for the new dmabuf objects
- random rxe failure due to missing memory zeroing
- static checker/etc reports: missing spin lock init, null pointer
deref on error, extra unlock on error path, memory allocation under
spinlock, missing IRQ vector cleanup
- kconfig typo in the new irdma driver"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/rxe: Zero out index member of struct rxe_queue
RDMA/efa: Free IRQ vectors on error flow
RDMA/rxe: Fix memory allocation while in a spin lock
RDMA/bnxt_re: Remove unpaired rtnl unlock in bnxt_re_dev_init()
IB/hfi1: Fix possible null-pointer dereference in _extend_sdma_tx_descs()
RDMA/irdma: Use correct kconfig symbol for AUXILIARY_BUS
RDMA/bnxt_re: Add missing spin lock initialization
RDMA/uverbs: Track dmabuf memory regions
RDMA/mlx5: Fix crash when unbind multiport slave
|
|
Building a randconfig here triggered:
ERROR: modpost: "pm_suspend_target_state" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
because the module export of that symbol happens in
kernel/power/suspend.c which is enabled with CONFIG_SUSPEND.
The ifdef guards in amdgpu_acpi_is_s0ix_supported(), however, test for
CONFIG_PM_SLEEP which is defined like this:
config PM_SLEEP
def_bool y
depends on SUSPEND || HIBERNATE_CALLBACKS
and that randconfig has:
# CONFIG_SUSPEND is not set
CONFIG_HIBERNATE_CALLBACKS=y
leading to the module export missing.
Change the ifdeffery to depend directly on CONFIG_SUSPEND.
Fixes: 5706cb3c910c ("drm/amdgpu: fix checking pmops when PM_SLEEP is not enabled")
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/YSP6Lv53QV0cOAsd@zn.tnic
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Fibocom FG150 is a 5G module based on Qualcomm SDX55 platform,
support Sub-6G band.
Here are the outputs of lsusb -v and usb-devices:
> T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
> D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
> P: Vendor=2cb7 ProdID=010b Rev=04.14
> S: Manufacturer=Fibocom
> S: Product=Fibocom Modem_SN:XXXXXXXX
> S: SerialNumber=XXXXXXXX
> C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=896mA
> I: If#=0x0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
> I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
> I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
> I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
> I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
> Bus 002 Device 002: ID 2cb7:010b Fibocom Fibocom Modem_SN:XXXXXXXX
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 3.20
> bDeviceClass 0
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 9
> idVendor 0x2cb7 Fibocom
> idProduct 0x010b
> bcdDevice 4.14
> iManufacturer 1 Fibocom
> iProduct 2 Fibocom Modem_SN:XXXXXXXX
> iSerial 3 XXXXXXXX
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 0x00e6
> bNumInterfaces 5
> bConfigurationValue 1
> iConfiguration 4 RNDIS_DUN_DIAG_ADB
> bmAttributes 0xa0
> (Bus Powered)
> Remote Wakeup
> MaxPower 896mA
> Interface Association:
> bLength 8
> bDescriptorType 11
> bFirstInterface 0
> bInterfaceCount 2
> bFunctionClass 239 Miscellaneous Device
> bFunctionSubClass 4
> bFunctionProtocol 1
> iFunction 7 RNDIS
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 1
> bInterfaceClass 239 Miscellaneous Device
> bInterfaceSubClass 4
> bInterfaceProtocol 1
> iInterface 0
> ** UNRECOGNIZED: 05 24 00 10 01
> ** UNRECOGNIZED: 05 24 01 00 01
> ** UNRECOGNIZED: 04 24 02 00
> ** UNRECOGNIZED: 05 24 06 00 01
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 3
> Transfer Type Interrupt
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0008 1x 8 bytes
> bInterval 9
> bMaxBurst 0
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 1
> bAlternateSetting 0
> bNumEndpoints 2
> bInterfaceClass 10 CDC Data
> bInterfaceSubClass 0
> bInterfaceProtocol 0
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x8e EP 14 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 6
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x0f EP 15 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 6
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 2
> bAlternateSetting 0
> bNumEndpoints 3
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 0
> bInterfaceProtocol 0
> iInterface 0
> ** UNRECOGNIZED: 05 24 00 10 01
> ** UNRECOGNIZED: 05 24 01 00 00
> ** UNRECOGNIZED: 04 24 02 02
> ** UNRECOGNIZED: 05 24 06 00 00
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x83 EP 3 IN
> bmAttributes 3
> Transfer Type Interrupt
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x000a 1x 10 bytes
> bInterval 9
> bMaxBurst 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x82 EP 2 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x01 EP 1 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 0
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 3
> bAlternateSetting 0
> bNumEndpoints 2
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 255 Vendor Specific Subclass
> bInterfaceProtocol 48
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x84 EP 4 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x02 EP 2 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 0
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 4
> bAlternateSetting 0
> bNumEndpoints 2
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 66
> bInterfaceProtocol 1
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x03 EP 3 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x85 EP 5 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 0
> Binary Object Store Descriptor:
> bLength 5
> bDescriptorType 15
> wTotalLength 0x0016
> bNumDeviceCaps 2
> USB 2.0 Extension Device Capability:
> bLength 7
> bDescriptorType 16
> bDevCapabilityType 2
> bmAttributes 0x00000006
> BESL Link Power Management (LPM) Supported
> SuperSpeed USB Device Capability:
> bLength 10
> bDescriptorType 16
> bDevCapabilityType 3
> bmAttributes 0x00
> wSpeedsSupported 0x000f
> Device can operate at Low Speed (1Mbps)
> Device can operate at Full Speed (12Mbps)
> Device can operate at High Speed (480Mbps)
> Device can operate at SuperSpeed (5Gbps)
> bFunctionalitySupport 1
> Lowest fully-functional device speed is Full Speed (12Mbps)
> bU1DevExitLat 1 micro seconds
> bU2DevExitLat 500 micro seconds
> Device Status: 0x0000
> (Bus Powered)
Signed-off-by: Zhengjun Zhang <zhangzhengjun@aicrobo.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In early erratas this issue only covered port 0 when changing from
[x]MII (rev A 3.6). In subsequent errata versions this errata changed to
cover the additional "Hardware reset in CPU managed mode" condition, and
removed the note specifying that it only applied to port 0.
In designs where the device is configured with CPU managed mode
(CPU_MGD), on reset all SERDES ports (p0, p9, p10) have a stuck power
down bit and require this initial power up procedure. As such apply this
errata to all three SERDES ports of the mv88e6393x.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For VFs we should return with an error in case we didn't get the exact
number of msix vectors as we requested.
Not doing that will lead to a crash when starting queues for this VF.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PCI devices expose the associated MSI interrupts via sysfs, but platform
devices which utilize MSI interrupts do not. This information is important
for user space tools to optimize affinity settings.
Utilize the generic MSI sysfs facility to expose this information for
platform MSI.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210813035628.6844-3-21cnbao@gmail.com
|
