| Age | Commit message (Collapse) | Author |
|---|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amdgpu:
- DCN 3.0 gamma fixes
- DCN 2.1 corrupt screen fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318042858.3810-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.12-rc4:
- Make ttm_bo_unpin() not wraparound on too many unpins.
- Fix coccicheck warning in omap.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a0e13bbb-6ba6-ff24-4db8-0e02e605de18@linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.12-rc cycle
Regression fixes for multiple issues found mostly caused by recent changes
to drop legacy platform data and and starting to use the new prm driver
reset controller:
- Fix ocp interconnect bus access error reporting for omap_l3_noc by
setting IRQF_NO_THREAD
- Fix changed mmc slot order regression by adding mmc aliases for am335x
- Fix dra7 reboot regression caused by invalid pcie reset map
- Fix smartreflex init regression caused by dropped legacy data
- Fix ti-sysc driver warning on unbind if reset is not deasserted
- Fix flakey reset deassert for dra7 iva
* tag 'omap-for-v5.12/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: omap-prm: Fix occasional abort on reset deassert for dra7 iva
bus: ti-sysc: Fix warning on unbind if reset is not deasserted
ARM: OMAP2+: Fix smartreflex init regression after dropping legacy data
soc: ti: omap-prm: Fix reboot issue with invalid pcie reset map for dra7
ARM: dts: am33xx: add aliases for mmc interfaces
bus: omap_l3_noc: mark l3 irqs as IRQF_NO_THREAD
Link: https://lore.kernel.org/r/pull-1614868603-800959@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix the following warning:
drivers/interconnect/bulk.c:63: warning: expecting prototype for
icc_bulk_set(). Prototype was for icc_bulk_set_bw() instead
Link: https://lore.kernel.org/r/20210318163415.30941-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
Commit 92c8c16f3457 ("powerpc/embedded6xx: Remove C2K board support")
removed last selector of CONFIG_MV64X60.
As it is not a user selectable config item, all references to it
are stale. Remove them.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize l4_key_offset variable to fix uninitialized
variable compiler warning.
Fixes: b9b7421a01d8 ("octeontx2-af: Support ESP/AH RSS hashing")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
unmapping npc counter works in a way by traversing all mcam
entries to find which mcam rule is associated with counter.
But loop cursor variable 'entry' is not incremented before
checking next mcam entry which resulting in infinite loop.
This in turn hogs the kworker thread forever and no other
mbox message is processed by AF driver after that.
Fix this by updating entry value before checking next
mcam entry.
Fixes: a958dd59f9ce ("octeontx2-af: Map or unmap NPC MCAM entry and counter")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RSS configuration can not be get/set when interface is in down state
as they required mbox communication. RSS enable flag status
is used for set/get configuration. Current code do not clear the
RSS enable flag on interface down which lead to mbox error while
trying to set/get RSS configuration.
Fixes: 85069e95e531 ("octeontx2-pf: Receive side scaling support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current devlink code try to free already freed irqs as the
irq_allocate flag is not cleared after free leading to kernel
crash while removing rvu driver. The patch fixes the irq free
sequence and clears the irq_allocate flag on free.
Fixes: 7304ac4567bc ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CGX receive buffer size is a constant value and
cannot be read from CGX0 block always since
CGX0 may not enabled everytime. Hence return CGX
receive buffer size from first enabled CGX block
instead of CGX0.
Fixes: 6e54e1c5399a ("octeontx2-af: cn10K: MTU configuration")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MKEX profile describes what packet fields need to be extracted from
the input packet and how to place those packet fields in the output key
for MCAM matching. The MKEX profile can be in a way where higher layer
packet fields can overwrite lower layer packet fields in output MCAM
Key.
Hence MKEX profile is always ensured that there are no overlaps between
any of the layers. But the commit 42006910b5ea
("octeontx2-af: cleanup KPU config data") introduced TX TOS field which
overlaps with DMAC in MCAM key.
This led to AF driver returning error when TX rule is installed with
DMAC as match criteria since DMAC gets overwritten and cannot be
supported. This patch fixes the issue by removing TOS field from MKEX TX
profile.
Fixes: 42006910b5ea ("octeontx2-af: cleanup KPU config data")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the existing rsrc_alloc's format, there is misalignment for the
pcifunc entries whose VF's index is a double digit. This patch fixes
this.
pcifunc NPA NIX0 NIX1 SSO GROUP SSOWS
TIM CPT0 CPT1 REE0 REE1
PF0:VF0 8 5
PF0:VF1 9 3
PF0:VF10 18 10
PF0:VF11 19 8
PF0:VF12 20 11
PF0:VF13 21 9
PF0:VF14 22 12
PF0:VF15 23 10
PF1 0 0
Fixes: 23205e6d06d4 ("octeontx2-af: Dump current resource provisioning status")
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the ETHTOOL_GRXCLSRLALL ioctl ethtool uses
below structure to read number of rules from the driver.
struct ethtool_rxnfc {
__u32 cmd;
__u32 flow_type;
__u64 data;
struct ethtool_rx_flow_spec fs;
union {
__u32 rule_cnt;
__u32 rss_context;
};
__u32 rule_locs[0];
};
Driver must not modify rule_cnt member. But currently driver
modifies it by modifying rss_context. Hence fix it by using a
local variable.
Fixes: 81a4362016e7 ("octeontx2-pf: Add RSS multi group support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull VFIO fixes from Alex Williamson:
- Fix 32-bit issue with new unmap-all flag (Steve Sistare)
- Various Kconfig changes for better coverage (Jason Gunthorpe)
- Fix to batch pinning support (Daniel Jordan)
* tag 'vfio-v5.12-rc4' of git://github.com/awilliam/linux-vfio:
vfio/type1: fix vaddr_get_pfns() return in vfio_pin_page_external()
vfio: Depend on MMU
ARM: amba: Allow some ARM_AMBA users to compile with COMPILE_TEST
vfio-platform: Add COMPILE_TEST to VFIO_PLATFORM
vfio: IOMMU_API should be selected
vfio/type1: fix unmap all on ILP32
|
|
Since commit 8e850f25b581 ("net: socionext: Stop PHY before resetting
netsec") netsec_netdev_init() power downs phy before resetting the
controller. However, the state is not restored once the reset is
complete. As a result it is not possible to bring up network on a
platform with Broadcom BCM5482 phy.
Fix the issue by restoring phy power state after controller reset is
complete.
Fixes: 8e850f25b581 ("net: socionext: Stop PHY before resetting netsec")
Cc: stable@vger.kernel.org
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull virtio fixes from Michael Tsirkin:
"Some fixes and cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost-vdpa: set v->config_ctx to NULL if eventfd_ctx_fdget() fails
vhost-vdpa: fix use-after-free of v->config_ctx
vhost: Fix vhost_vq_reset()
vhost_vdpa: fix the missing irq_bypass_unregister_producer() invocation
vdpa_sim: Skip typecasting from void*
virtio: remove export for virtio_config_{enable, disable}
virtio-mmio: Use to_virtio_mmio_device() to simply code
vdpa: set the virtqueue num during register
|
|
Dmitry Osipenko <digetx@gmail.com>:
Hi,
This series adds missing hardware reset controls to I2S and AC97 drivers,
corrects runtime PM usage and drivers probe/remove order. Currently drivers
happen to work properly because reset is implicitly deasserted by tegra-clk
driver, but clk driver shouldn't touch the resets and we need to fix it
because this breaks other Tegra drivers. Previously we fixed the resets of
the AHUB and HDMI codec drivers, but turned out that we missed the I2C and
AC97 drivers.
Thanks to Paul Fertser for testing the pending clk patches and finding
that audio got broken on Tegra20 AC100 netbook because of the missing I2S
reset.
Changelog:
v5: - After taking another look at the drivers I noticed couple more
things that could be improved. These new patches correct runtime PM
and probe/remove order of the drivers:
ASoC: tegra20: spdif: Correct driver removal order
ASoC: tegra20: spdif: Remove handing of disabled runtime PM
ASoC: tegra20: i2s: Add system level suspend-resume callbacks
ASoC: tegra20: i2s: Correct driver removal order
ASoC: tegra20: i2s: Use devm_clk_get()
ASoC: tegra20: i2s: Remove handing of disabled runtime PM
ASoC: tegra30: i2s: Correct driver removal order
ASoC: tegra30: i2s: Use devm_clk_get()
ASoC: tegra30: i2s: Remove handing of disabled runtime PM
ASoC: tegra30: ahub: Reset global variable
ASoC: tegra30: ahub: Correct suspend-resume callbacks
ASoC: tegra30: ahub: Remove handing of disabled runtime PM
v4: - Added missing prototype for reset_control_bulk_put().
v3: - Fixed reset stubs for !CONFIG_RESET_CONTROLLER.
v2: - After some more testing I found that I2S control logic doesn't require
I2S clock to be enabled for resetting. Hence it's fine to have I2S to
be reset by parent AHUB driver, so I dropped "tegra30: i2s: Add reset
control" patch.
- While I was double-checking resets on Tegra30, I found that that
Tegra30 I2S driver has a broken runtime PM which doesn't restore
hardware state on resume and it's lost after AHUB RPM-resume.
Thus, added this new patch "tegra30: i2s: Restore hardware state
on runtime PM resume".
- Added new patches which switch AHUB driver to use reset-bulk API.
I took the RFC patch from Philipp Zabel, fixed it and added
devm_reset_control_bulk_optional_get_exclusive_released() that
will be useful for further Tegra GPU patches. This is a minor
improvement which makes code cleaner.
Dmitry Osipenko (16):
ASoC: tegra20: ac97: Add reset control
ASoC: tegra20: i2s: Add reset control
ASoC: tegra30: i2s: Restore hardware state on runtime PM resume
ASoC: tegra30: ahub: Switch to use reset-bulk API
ASoC: tegra20: spdif: Correct driver removal order
ASoC: tegra20: spdif: Remove handing of disabled runtime PM
ASoC: tegra20: i2s: Add system level suspend-resume callbacks
ASoC: tegra20: i2s: Correct driver removal order
ASoC: tegra20: i2s: Use devm_clk_get()
ASoC: tegra20: i2s: Remove handing of disabled runtime PM
ASoC: tegra30: i2s: Correct driver removal order
ASoC: tegra30: i2s: Use devm_clk_get()
ASoC: tegra30: i2s: Remove handing of disabled runtime PM
ASoC: tegra30: ahub: Reset global variable
ASoC: tegra30: ahub: Correct suspend-resume callbacks
ASoC: tegra30: ahub: Remove handing of disabled runtime PM
Philipp Zabel (1):
reset: Add reset_control_bulk API
drivers/reset/core.c | 215 ++++++++++++++++++++++
include/linux/reset.h | 315 ++++++++++++++++++++++++++++++++
sound/soc/tegra/tegra20_ac97.c | 21 +++
sound/soc/tegra/tegra20_ac97.h | 1 +
sound/soc/tegra/tegra20_i2s.c | 60 +++---
sound/soc/tegra/tegra20_i2s.h | 1 +
sound/soc/tegra/tegra20_spdif.c | 16 +-
sound/soc/tegra/tegra30_ahub.c | 168 ++++++-----------
sound/soc/tegra/tegra30_ahub.h | 5 +-
sound/soc/tegra/tegra30_i2s.c | 65 ++-----
10 files changed, 667 insertions(+), 200 deletions(-)
--
2.30.2
base-commit: a38fd8748464831584a19438cbb3082b5a2dab15
|
|
Follow the clock and regulator subsystems' lead and add a bulk API
for reset controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-5-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Lenovo platforms with DYTC versions earlier than version 5 don't set
the lapmode interface correctly, causing issues with thermald on
older platforms.
Add checking to only create the dytc_lapmode interface for version
5 and later.
Fixes: 1ac09656bded ("platform/x86: thinkpad_acpi: Add palm sensor support")
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Link: https://lore.kernel.org/r/20210311174843.3161-1-markpearson@lenovo.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The jack handling for arizona codecs is being refactored so that it is
done directly by the codec drivers, instead of having an extcon-driver
bind to a separate "arizona-extcon" child-device for this.
drivers/mfd/arizona-core.c has already been updated to no longer
instantiate an "arizona-extcon" child-device for the arizona codecs.
This means that the "arizona-extcon" driver is no longer useful
(there are no longer any devices for it to bind to).
This commit drops the extcon Kconfig / Makefile bits and moves
drivers/extcon/extcon-arizona.c to sound/soc/codecs/arizona-jack.c .
This is a preparation patch for converting the arizona extcon-driver into
a helper library for letting the arizona codec-drivers directly report jack
state through the standard sound/soc/soc-jack.c functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
be awake
Before this commit the extcon-arizona code was mixing pm_runtime_get()
and pm_runtime_get_sync() in different places.
In all places where pm_runtime_get[_sync]() is called, the code
makes use of the device immediately after the call.
This means that we should always use pm_runtime_get_sync().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The initial value of the GPIO should match the info->micd_modes[0].gpio
value. arizona_extcon_probe() already stores the necessary flag in a
mode variable, but instead of passing mode as flags to the gpiod_get()
it was using a hardcoded GPIOD_OUT_LOW.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We must free/disable all interrupts and cancel all pending works
before doing further cleanup.
Before this commit arizona_extcon_remove() was doing several
register writes to shut things down before disabling the IRQs
and it was cancelling only 1 of the 3 different works used.
Move all the register-writes shutting things down to after
the disabling of the IRQs and add the 2 missing
cancel_delayed_work_sync() calls.
This fixes various possible races on driver unbind. One of which
would always trigger on devices using the mic-clamp feature for
jack detection. The ARIZONA_MICD_CLAMP_MODE_MASK update was
done before disabling the IRQs, causing:
1. arizona_jackdet() to run
2. detect a jack being inserted (clamp disabled means jack inserted)
3. call arizona_start_mic() which:
3.1 Enables the MICVDD regulator
3.2 takes a pm_runtime_reference
And this was all happening after the ARIZONA_MICD_ENA bit clearing,
which would undo 3.1 and 3.2 because the ARIZONA_MICD_CLAMP_MODE_MASK
update was being done after the ARIZONA_MICD_ENA bit clearing.
So this means that arizona_extcon_remove() would exit with
1. MICVDD enabled and 2. The pm_runtime_reference being unbalanced.
MICVDD still being enabled caused the following oops when the
regulator is released by the devm framework:
[ 2850.745757] ------------[ cut here ]------------
[ 2850.745827] WARNING: CPU: 2 PID: 2098 at drivers/regulator/core.c:2123 _regulator_put.part.0+0x19f/0x1b0
[ 2850.745835] Modules linked in: extcon_arizona ...
...
[ 2850.746909] Call Trace:
[ 2850.746932] regulator_put+0x2d/0x40
[ 2850.746946] release_nodes+0x22a/0x260
[ 2850.746984] __device_release_driver+0x190/0x240
[ 2850.747002] driver_detach+0xd4/0x120
...
[ 2850.747337] ---[ end trace f455dfd7abd9781f ]---
Note this oops is just one of various theoretically possible races caused
by the wrong ordering inside arizona_extcon_remove(), this fixes the
ordering fixing all possible races, including the reported oops.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
been unplugged
When the jack is partially inserted and then removed again it may be
removed while the hpdet code is running. In this case the following
may happen:
1. The "JACKDET rise" or ""JACKDET fall" IRQ triggers
2. arizona_jackdet runs and takes info->lock
3. The "HPDET" IRQ triggers
4. arizona_hpdet_irq runs, blocks on info->lock
5. arizona_jackdet calls arizona_stop_mic() and clears info->hpdet_done
6. arizona_jackdet releases info->lock
7. arizona_hpdet_irq now can continue running and:
7.1 Calls arizona_start_mic() (if a mic was detected)
7.2 sets info->hpdet_done
Step 7 is undesirable / a bug:
7.1 causes the device to stay in a high power-state (with MICVDD enabled)
7.2 causes hpdet to not run on the next jack insertion, which in turn
causes the EXTCON_JACK_HEADPHONE state to never get set
This fixes both issues by skipping these 2 steps when arizona_hpdet_irq
runs after the jack has been unplugged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The arizona jack-dection handling is being reworked so that the
codec-child-device drivers directly handle jack-detect themselves,
so it is no longer necessary to instantiate "arizona-extcon"
child-devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
In some configurations, recovery is optional. So, don't throw an error
when it is not used because e.g. pinctrl settings for recovery are not
provided. Reword the message and make it debug output.
Reported-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: stable@kernel.org
|
|
The tegra_smmu_probe_device() handles only the first IOMMU device-tree
phandle, skipping the rest. Devices like 3D module on Tegra30 have
multiple IOMMU phandles, one for each h/w block, and thus, only one
IOMMU phandle is added to fwspec for the 3D module, breaking GPU.
Previously this problem was masked by tegra_smmu_attach_dev() which
didn't use the fwspec, but parsed the DT by itself. The previous commit
to tegra-smmu driver partially reverted changes that caused problems for
T124 and now we have tegra_smmu_attach_dev() that uses the fwspec and
the old-buggy variant of tegra_smmu_probe_device() which skips secondary
IOMMUs.
Make tegra_smmu_probe_device() not to skip the secondary IOMMUs. This
fixes a partially attached IOMMU of the 3D module on Tegra30 and now GPU
works properly once again.
Fixes: 765a9d1d02b2 ("iommu/tegra-smmu: Fix mc errors on tegra124-nyan")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20210312155439.18477-1-digetx@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The amd_iommu_irq_remap variable is set to true in amd_iommu_prepare().
But if initialization fails it is not set to false. Fix that and
correctly keep track of whether irq remapping is enabled or not.
References: https://bugzilla.kernel.org/show_bug.cgi?id=212133
References: https://bugzilla.suse.com/show_bug.cgi?id=1183132
Fixes: b34f10c2dc59 ("iommu/amd: Stop irq_remapping_select() matching when remapping is disabled")
Cc: stable@vger.kernel.org # v5.11
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20210317091037.31374-4-joro@8bytes.org
Acked-by: Huang Rui <ray.huang@amd.com>
|
|
Don't even try to initialize the AMD IOMMU hardware when amd_iommu=off has been
passed on the kernel command line.
References: https://bugzilla.kernel.org/show_bug.cgi?id=212133
References: https://bugzilla.suse.com/show_bug.cgi?id=1183132
Cc: stable@vger.kernel.org # v5.11
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20210317091037.31374-3-joro@8bytes.org
Acked-by: Huang Rui <ray.huang@amd.com>
|
|
The AMD IOMMU will not be enabled on AMD Stoney Ridge systems. Bail
out even earlier and refuse to even detect the IOMMU there.
References: https://bugzilla.kernel.org/show_bug.cgi?id=212133
References: https://bugzilla.suse.com/show_bug.cgi?id=1183132
Cc: stable@vger.kernel.org # v5.11
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20210317091037.31374-2-joro@8bytes.org
Acked-by: Huang Rui <ray.huang@amd.com>
|
|
Removing 2 instances of alignment warnings
drivers/staging/vt6655/rxtx.h:153:1: warning: alignment 1 of ‘struct vnt_cts’ is less than 2 [-Wpacked-not-aligned]
drivers/staging/vt6655/rxtx.h:163:1: warning: alignment 1 of ‘struct vnt_cts_fb’ is less than 2 [-Wpacked-not-aligned]
The root cause seems to be that _because_ struct ieee80211_cts is marked as __aligned(2),
this requires any encapsulating struct to also have an alignment of 2.
Fixes: 2faf12c57efe ("staging: vt665x: fix alignment constraints")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Edmundo Carmona Antoranz <eantoranz@gmail.com>
Link: https://lore.kernel.org/r/20210316181736.2553318-1-eantoranz@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When port partner responds "Not supported" to the DiscIdentity command,
VDM state machine can remain in NVDM_STATE_ERR_TMOUT and this causes
querying sink cap to be skipped indefinitely. Hence check for
vdm_sm_running instead of checking for VDM_STATE_DONE.
Fixes: 8dc4bd073663f ("usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210318064805.3747831-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When data digest is enabled we should unmap pdu iovec before handling
the data digest pdu.
Signed-off-by: Elad Grupi <elad.grupi@dell.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
From the base spec, Figure 78:
"Controller Configuration, these fields are defined as parameters to
configure an "I/O Controller (IOC)" and not to configure a "Discovery
Controller (DC).
...
If the controller does not support I/O queues, then this field shall
be read-only with a value of 0h
Just perform this check for I/O controllers.
Fixes: a07b4970f464 ("nvmet: add a generic NVMe target")
Reported-by: Belanger, Martin <Martin.Belanger@dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We only setup io queues for nvme controllers, and it makes absolutely no
sense to allow a controller (re)connect without any I/O queues. If we
happen to fail setting the queue count for any reason, we should not allow
this to be a successful reconnect as I/O has no chance in going through.
Instead just fail and schedule another reconnect.
Reported-by: Chao Leng <lengchao@huawei.com>
Fixes: 711023071960 ("nvme-rdma: add a NVMe over Fabrics RDMA host driver")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chao Leng <lengchao@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We only setup io queues for nvme controllers, and it makes absolutely no
sense to allow a controller (re)connect without any I/O queues. If we
happen to fail setting the queue count for any reason, we should not
allow this to be a successful reconnect as I/O has no chance in going
through. Instead just fail and schedule another reconnect.
Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
For our pure advisory use-case, we only rely on this call as a hint, so
fix the warning complaints of using the smp_processor_id variants with
preemption enabled.
Fixes: db5ad6b7f8cd ("nvme-tcp: try to send request in queue_rq context")
Fixes: ada831772188 ("nvme-tcp: Fix warning with CONFIG_DEBUG_PREEMPT")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When the controller sends us a 0-length r2t PDU we should not attempt to
try to set up a h2cdata PDU but rather conclude that this is a buggy
controller (forward progress is not possible) and simply fail it
immediately.
Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver")
Reported-by: Belanger, Martin <Martin.Belanger@dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We voluntarily limit the Write Zeroes sizes to the MDTS value provided by
the hardware, but currently get the units wrong, so fix that.
Fixes: 6e02318eaea5 ("nvme: add support for the Write Zeroes command")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
|
|
To avoid an error recovery deadlock where the keep alive work is waiting
for a request and thus can't be flushed to make progress for tearing down
the controller. Also print the error code returned from
blk_mq_alloc_request to help debugging any future issues in this code.
Based on an earlier patch from Hannes Reinecke <hare@suse.de>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
|
|
Merge nvme_keep_alive into its only caller to prepare for additional
changes to this code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
|
|
Fabrics drivers currently reserve two tags on the admin queue. But
given that the connect command is only run on a freshly created queue
or after all commands have been force aborted we only need to reserve
a single tag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
|
|
[Why?]
Should only reroute gamut remap to mpc unless 3D LUT is not used and all
planes are using the same src->dest.
[How?]
Remove DCN30 specific logic for rerouting gamut remap to mpc.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1513
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
DCN30 needs to correctly program reversed gamma curve, which DCN20
already has.
Also needs to fix a bug that 252-255 values are clipped.
[How]
Apply two fixes into DCN30.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1513
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Calvin Hou <Calvin.Hou@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Acked-by: Vladimir Stempen <Vladimir.Stempen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We have seen a couple cases where low memory situations cause something
bad to happen, followed by a flood of these messages obscuring the root
cause. Lets ratelimit the dmesg spam so that next time it happens we
don't lose the kernel traces leading up to this.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
In the situations where the DWC3 gadget stops active transfers, once
calling the dwc3_gadget_giveback(), there is a chance where a function
driver can queue a new USB request in between the time where the dwc3
lock has been released and re-aquired. This occurs after we've already
issued an ENDXFER command. When the stop active transfers continues
to remove USB requests from all dep lists, the newly added request will
also be removed, while controller still has an active TRB for it.
This can lead to the controller accessing an unmapped memory address.
Fix this by ensuring parameters to prevent EP queuing are set before
calling the stop active transfers API.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1615507142-23097-1-git-send-email-wcheng@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm-source-psy- does not invoke power_supply_changed API when
one of the published power supply properties is changed.
power_supply_changed needs to be called to notify
userspace clients(uevents) and kernel clients.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210317181249.1062995-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the unused "u32 vdo[3]" part in the tps6598x_rx_identity_reg
struct. This helps avoid "failed to register partner" errors which
happen when tps6598x_read_partner_identity() fails because the
amount of data read is 12 bytes smaller than the struct size.
Note that vdo[3] is already in usb_pd_identity and hence
shouldn't be added to tps6598x_rx_identity_reg as well.
Fixes: f6c56ca91b92 ("usb: typec: Add the Product Type VDOs to struct usb_pd_identity")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Elias Rudberg <mail@eliasrudberg.se>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210311124710.6563-1-mail@eliasrudberg.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Matthias reports that the Amazon Kindle automatically removes its
emulated media if it doesn't receive another SCSI command within about
one second after a SYNCHRONIZE CACHE. It does so even when the host
has sent a PREVENT MEDIUM REMOVAL command. The reason for this
behavior isn't clear, although it's not hard to make some guesses.
At any rate, the results can be unexpected for anyone who tries to
access the Kindle in an unusual fashion, and in theory they can lead
to data loss (for example, if one file is closed and synchronized
while other files are still in the middle of being written).
To avoid such problems, this patch creates a new usb-storage quirks
flag telling the driver always to issue a REQUEST SENSE following a
SYNCHRONIZE CACHE command, and adds an unusual_devs entry for the
Kindle with the flag set. This is sufficient to prevent the Kindle
from doing its automatic unload, without interfering with proper
operation.
Another possible way to deal with this would be to increase the
frequency of TEST UNIT READY polling that the kernel normally carries
out for removable-media storage devices. However that would increase
the overall load on the system and it is not as reliable, because the
user can override the polling interval. Changing the driver's
behavior is safer and has minimal overhead.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210317190654.GA497856@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When gadget is disconnected, running sequence is like this.
. composite_disconnect
. Call trace:
usb_string_copy+0xd0/0x128
gadget_config_name_configuration_store+0x4
gadget_config_name_attr_store+0x40/0x50
configfs_write_file+0x198/0x1f4
vfs_write+0x100/0x220
SyS_write+0x58/0xa8
. configfs_composite_unbind
. configfs_composite_bind
In configfs_composite_bind, it has
"cn->strings.s = cn->configuration;"
When usb_string_copy is invoked. it would
allocate memory, copy input string, release previous pointed memory space,
and use new allocated memory.
When gadget is connected, host sends down request to get information.
Call trace:
usb_gadget_get_string+0xec/0x168
lookup_string+0x64/0x98
composite_setup+0xa34/0x1ee8
If gadget is disconnected and connected quickly, in the failed case,
cn->configuration memory has been released by usb_string_copy kfree but
configfs_composite_bind hasn't been run in time to assign new allocated
"cn->configuration" pointer to "cn->strings.s".
When "strlen(s->s) of usb_gadget_get_string is being executed, the dangling
memory is accessed, "BUG: KASAN: use-after-free" error occurs.
Cc: stable@vger.kernel.org
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/1615444961-13376-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
