| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 1e35f074399dece73d5df11847d4a0d7a6f49434.
Given that ERROR_RECOVERY calls into PORT_RESET for Hi-Zing
the CC pins, setting CC pins to default state during PORT_RESET
breaks error recovery.
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Cc: stable@vger.kernel.org
Cc: Frank Wang <frank.wang@rock-chips.com>
Fixes: 1e35f074399d ("usb: typec: tcpm: fix cc role at port reset")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240117114742.2587779-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Delete one extraneous line of kernel-doc to prevent a kernel-doc
warning:
pch_udc.c:297: warning: Excess struct member 'desc' description in 'pch_udc_ep'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: tomoya-linux@dsn.lapis-semi.com
Link: https://lore.kernel.org/r/20240115003008.5763-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
Cc: stable <stable@kernel.org>
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240123034829.3848409-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The OTG 1.3 spec has the feature A_ALT_HNP_SUPPORT, which tells
a device that it is connected to the wrong port. Some devices
refuse to operate if you enable that feature, because it indicates
to them that they ought to request to be connected to another port.
According to the spec this feature may be used based only the following
three conditions:
6.5.3 a_alt_hnp_support
Setting this feature indicates to the B-device that it is connected to
an A-device port that is not capable of HNP, but that the A-device does
have an alternate port that is capable of HNP.
The A-device is required to set this feature under the following conditions:
• the A-device has multiple receptacles
• the A-device port that connects to the B-device does not support HNP
• the A-device has another port that does support HNP
A check for the third and first condition is missing. Add it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 7d2d641c44269 ("usb: otg: don't set a_alt_hnp_support feature for OTG 2.0 device")
Link: https://lore.kernel.org/r/20240122153545.12284-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When power is recycled in usb controller during system power management,
the controller will recognize it and switch role if role has been changed
during power lost. In current design, it will be completed in resume()
function. However, this may bring issues since usb class devices have
their pm operations too and these device's resume() functions are still
not being called at this point. When usb controller recognized host role
should be stopped, these usb class devices will be removed at this point.
But these usb class devices can't be removed in some cases, such as scsi
devices. Since scsi driver may sync data to U-disk, however it will block
there because scsi drvier can only handle pm request when is in suspended
state. Therefore, there may exist a dependency between ci_resume() and usb
class device's resume(). To break this potential dependency, we need to
handle power lost work in a workqueue.
Fixes: 74494b33211d ("usb: chipidea: core: add controller resume support when controller is powered off")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240119123537.3614838-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In current scenario if Plug-out and Plug-In performed continuously
there could be a chance while checking for dwc->gadget_driver in
dwc3_gadget_suspend, a NULL pointer dereference may occur.
Call Stack:
CPU1: CPU2:
gadget_unbind_driver dwc3_suspend_common
dwc3_gadget_stop dwc3_gadget_suspend
dwc3_disconnect_gadget
CPU1 basically clears the variable and CPU2 checks the variable.
Consider CPU1 is running and right before gadget_driver is cleared
and in parallel CPU2 executes dwc3_gadget_suspend where it finds
dwc->gadget_driver which is not NULL and resumes execution and then
CPU1 completes execution. CPU2 executes dwc3_disconnect_gadget where
it checks dwc->gadget_driver is already NULL because of which the
NULL pointer deference occur.
Cc: stable@vger.kernel.org
Fixes: 9772b47a4c29 ("usb: dwc3: gadget: Fix suspend/resume during device mode")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20240119094825.26530-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds the necessary PCI ID for Intel Arrow Lake-H
devices.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240115092820.1454492-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the function update_port_device_state gets the usb_hub from
udev->parent by calling usb_hub_to_struct_hub.
However, in case the actconfig or the maxchild is 0, the usb_hub would
be NULL and upon further accessing to get port_dev would result in null
pointer dereference.
Fix this by introducing an if check after the usb_hub is populated.
Fixes: 83cb2604f641 ("usb: core: add sysfs entry for usb device state")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240110095814.7626-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sanity check of interrupter index when adding a new interrupter is
off by one. intr_num needs to be smaller than xhci->max_interrupter to
fit the array of interrupters.
Luckily this doesn't cause any real word harm as xhci_add_interrupter()
is always called with a intr_num value smaller than xhci->max_interrupters
in any current kernel.
Should not be needed for stable as 6.7 kernel and older only supports
one interrupter, with intr_num always being zero.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-usb/e9771296-586d-456a-ac24-a82de79bb2e6@moroto.mountain/
Fixes: 4bf398e15aa4 ("xhci: split allocate interrupter into separate alloacte and add parts")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't try to remove a secondary interrupter that is known to be invalid.
Also check if the interrupter is valid inside the spinlock that protects
the array of interrupters.
Found by smatch static checker
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-usb/ffaa0a1b-5984-4a1f-bfd3-9184630a97b9@moroto.mountain/
Fixes: c99b38c41234 ("xhci: add support to allocate several interrupters")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Recent commit [1] added support for changing max segment size of the NCM
interface via configfs. But the value of segment size value stored in
ncm_opts need to be converted to little endian before saving it in
ecm_desc. Also while initialising the value of segment size in opts during
instance allocation, the value ETH_FRAME_LEN needs to be assigned directly
without any conversion as ETH_FRAME_LEN and the variable max_segment_size
are native endian. The current implementaion modifies it into little endian
thus breaking things for big endian targets.
Fix endianness while assigning these variables.
While at it, fix up some stray spaces in comments added in code.
[1]: https://lore.kernel.org/all/20231221153216.18657-1-quic_kriskura@quicinc.com/
Fixes: 1900daeefd3e ("usb: gadget: ncm: Add support to update wMaxSegmentSize via configfs")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240118154910.8765-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Upstream commit bac1ec551434 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. Currently this quirk can only be set using
xhci private data. But there are some drivers like dwc3/host.c
which adds adds quirks using software node for xhci device.
Hence set this xhci quirk by iterating over device properties.
Cc: stable@vger.kernel.org # 5.11
Fixes: bac1ec551434 ("usb: xhci: Set quirk for XHCI_SG_TRB_CACHE_SIZE_QUIRK")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-3-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Upstream commit bac1ec551434 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. But the support for this quirk isn't present
in the DWC3 layer.
We will encounter this XHCI timeout/hung issue if we run iperf
loopback tests using RTL8156 ethernet adaptor on DWC3 targets
with scatter-gather enabled. This gets resolved after enabling
the XHCI_SG_TRB_CACHE_SIZE_QUIRK. This patch enables it using
the xhci device property since its needed for DWC3 controller.
In Synopsys DWC3 databook,
Table 9-3: xHCI Debug Capability Limitations
Chained TRBs greater than TRB cache size: The debug capability
driver must not create a multi-TRB TD that describes smaller
than a 1K packet that spreads across 8 or more TRBs on either
the IN TR or the OUT TR.
Cc: stable@vger.kernel.org #5.11
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-2-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- WMI bus driver fixes
- Second attempt (previously reverted) at P2SB PCI rescan deadlock fix
- AMD PMF driver improvements
- MAINTAINERS updates
- Misc other small fixes and hw-id additions
* tag 'platform-drivers-x86-v6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: touchscreen_dmi: Add info for the TECLAST X16 Plus tablet
platform/x86/intel/ifs: Call release_firmware() when handling errors.
platform/x86/amd/pmf: Fix memory leak in amd_pmf_get_pb_data()
platform/x86/amd/pmf: Get ambient light information from AMD SFH driver
platform/x86/amd/pmf: Get Human presence information from AMD SFH driver
platform/mellanox: mlxbf-pmc: Fix offset calculation for crspace events
platform/mellanox: mlxbf-tmfifo: Drop Tx network packet when Tx TmFIFO is full
MAINTAINERS: remove defunct acpi4asus project info from asus notebooks section
MAINTAINERS: add Luke Jones as maintainer for asus notebooks
MAINTAINERS: Remove Perry Yuan as DELL WMI HARDWARE PRIVACY SUPPORT maintainer
platform/x86: silicom-platform: Add missing "Description:" for power_cycle sysfs attr
platform/x86: intel-wmi-sbl-fw-update: Fix function name in error message
platform/x86: p2sb: Use pci_resource_n() in p2sb_read_bar0()
platform/x86: p2sb: Allow p2sb_bar() calls during PCI device probe
platform/x86: intel-uncore-freq: Fix types in sysfs callbacks
platform/x86: wmi: Fix wmi_dev_probe()
platform/x86: wmi: Fix notify callback locking
platform/x86: wmi: Decouple legacy WMI notify handlers from wmi_block_list
platform/x86: wmi: Return immediately if an suitable WMI event is found
platform/x86: wmi: Fix error handling in legacy WMI notify handler functions
|
|
The current driver code no longer perfrom internal conversion from
VID to direct. Instead it configures READ_VOUT using MFR_DC_LOOP_CTRL.
Correct the comment message inside the 'mp2975_read_byte_data'
function to match the driver logic.
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Fixes: c60fe56c169e ("hwmon: (pmbus/mp2975) Fix driver initialization for MP2975 device")
Link: https://lore.kernel.org/r/20240127154844.989-1-aladyshev22@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In the current interrupt controller, the MAC interrupt acts as the
parent interrupt in the GPIO IRQ chip. But when the number of Rx/Tx
ring changes, the PCI IRQ vector needs to be reallocated. Then this
interrupt controller would be corrupted. So use irq_domain structure
to avoid the above problem.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to change the interrupt response structure, there will be a
lot of code added next. Move these interrupt codes to a new file, to
make the codes cleaner.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case the interface between the MAC and the PHY is SGMII, then the bit
GIGA_MODE on the MAC side needs to be set regardless of the speed at
which it is running.
Fixes: d28d6d2e37d1 ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8873
Correct the PHY loopback bit handling in the ksz8_w_phy_bmcr and
ksz8_r_phy_bmcr functions for KSZ8794 and KSZ8873 variants in the ksz8795
driver. Previously, the code erroneously used Bit 7 of port register 0xD
for both chip variants, which is actually for LED configuration. This
update ensures the correct registers and bits are used for the PHY
loopback feature:
- For KSZ8794: Use 0xF / Bit 7.
- For KSZ8873: Use 0xD / Bit 0.
The lack of loopback support was seen on KSZ8873 system by using
"ethtool -t lanX". After this patch, the ethtool selftest will work,
but only if port is not part of a bridge.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the manual checks for register value changes in the
ksz8_w_phy_bmcr function. Instead, rely on regmap_update_bits() for
optimizing register updates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Isolate the Basic Mode Control Register (BMCR) operations in the ksz8795
driver by moving the BMCR-related code segments from the ksz8_r_phy()
and ksz8_w_phy() functions to newly created ksz8_r_phy_bmcr() and
ksz8_w_phy_bmcr() functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2024-01-26
We've added 107 non-merge commits during the last 4 day(s) which contain
a total of 101 files changed, 6009 insertions(+), 1260 deletions(-).
The main changes are:
1) Add BPF token support to delegate a subset of BPF subsystem
functionality from privileged system-wide daemons such as systemd
through special mount options for userns-bound BPF fs to a trusted
& unprivileged application. With addressed changes from Christian
and Linus' reviews, from Andrii Nakryiko.
2) Support registration of struct_ops types from modules which helps
projects like fuse-bpf that seeks to implement a new struct_ops type,
from Kui-Feng Lee.
3) Add support for retrieval of cookies for perf/kprobe multi links,
from Jiri Olsa.
4) Bigger batch of prep-work for the BPF verifier to eventually support
preserving boundaries and tracking scalars on narrowing fills,
from Maxim Mikityanskiy.
5) Extend the tc BPF flavor to support arbitrary TCP SYN cookies to help
with the scenario of SYN floods, from Kuniyuki Iwashima.
6) Add code generation to inline the bpf_kptr_xchg() helper which
improves performance when stashing/popping the allocated BPF objects,
from Hou Tao.
7) Extend BPF verifier to track aligned ST stores as imprecise spilled
registers, from Yonghong Song.
8) Several fixes to BPF selftests around inline asm constraints and
unsupported VLA code generation, from Jose E. Marchesi.
9) Various updates to the BPF IETF instruction set draft document such
as the introduction of conformance groups for instructions,
from Dave Thaler.
10) Fix BPF verifier to make infinite loop detection in is_state_visited()
exact to catch some too lax spill/fill corner cases,
from Eduard Zingerman.
11) Refactor the BPF verifier pointer ALU check to allow ALU explicitly
instead of implicitly for various register types, from Hao Sun.
12) Fix the flaky tc_redirect_dtime BPF selftest due to slowness
in neighbor advertisement at setup time, from Martin KaFai Lau.
13) Change BPF selftests to skip callback tests for the case when the
JIT is disabled, from Tiezhu Yang.
14) Add a small extension to libbpf which allows to auto create
a map-in-map's inner map, from Andrey Grafin.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (107 commits)
selftests/bpf: Add missing line break in test_verifier
bpf, docs: Clarify definitions of various instructions
bpf: Fix error checks against bpf_get_btf_vmlinux().
bpf: One more maintainer for libbpf and BPF selftests
selftests/bpf: Incorporate LSM policy to token-based tests
selftests/bpf: Add tests for LIBBPF_BPF_TOKEN_PATH envvar
libbpf: Support BPF token path setting through LIBBPF_BPF_TOKEN_PATH envvar
selftests/bpf: Add tests for BPF object load with implicit token
selftests/bpf: Add BPF object loading tests with explicit token passing
libbpf: Wire up BPF token support at BPF object level
libbpf: Wire up token_fd into feature probing logic
libbpf: Move feature detection code into its own file
libbpf: Further decouple feature checking logic from bpf_object
libbpf: Split feature detectors definitions from cached results
selftests/bpf: Utilize string values for delegate_xxx mount options
bpf: Support symbolic BPF FS delegation mount options
bpf: Fail BPF_TOKEN_CREATE if no delegation option was set on BPF FS
bpf,selinux: Allocate bpf_security_struct per BPF token
selftests/bpf: Add BPF token-enabled tests
libbpf: Add BPF token support to bpf_prog_load() API
...
====================
Link: https://lore.kernel.org/r/20240126215710.19855-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add LED support for QCA8081 PHY.
Documentation for this LEDs PHY is very scarce even with NDA access
to Documentation for OEMs. Only the blink pattern are documented and are
very confusing most of the time. No documentation is present about
forcing the LED on/off or to always blink.
Those settings were reversed by poking the regs and trying to find the
correct bits to trigger these modes. Some bits mode are not clear and
maybe the documentation option are not 100% correct. For the sake of LED
support the reversed option are enough to add support for current LED
APIs.
Supported HW control modes are:
- tx
- rx
- link_10
- link_100
- link_1000
- link_2500
- half_duplex
- full_duplex
Also add support for LED polarity set to set LED polarity to active
high or low. QSDK sets this value to high by default but PHY reset value
doesn't have this enabled by default.
QSDK also sets 2 additional bits but their usage is not clear, info about
this is added in the header. It was verified that for correct function
of the LED if active high is needed, only BIT 6 is needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125203702.4552-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for PHY LEDs polarity modes. Some PHY require LED to be set
to active low to be turned ON. Adds support for this by declaring
active-low property in DT.
PHY driver needs to declare .led_polarity_set() to configure LED
polarity modes. Function will pass the index with the LED index and a
bitmap with all the required modes to set.
Current supported modes are:
- active-low with the flag PHY_LED_ACTIVE_LOW. LED is set to active-low
to turn it ON.
- inactive-high-impedance with the flag PHY_LED_INACTIVE_HIGH_IMPEDANCE.
LED is set to high impedance to turn it OFF.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125203702.4552-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A potential string truncation was reported in bnx2x_fill_fw_str(),
when a long bp->fw_ver and a long phy_fw_ver might coexist, but seems
unlikely with real-world hardware.
Use scnprintf() to indicate the intent that truncations are tolerated.
While reading this code, I found a collection of various buffer size
counting issues. None looked like they might lead to a buffer overflow
with current code (the small buffers are 20 bytes and might only ever
consume 10 bytes twice with a trailing %NUL). However, early truncation
(due to a %NUL in the middle of the string) might be happening under
likely rare conditions. Regardless fix the formatters and related
functions:
- Switch from a separate strscpy() to just adding an additional "%s" to
the format string that immediately follows it in bnx2x_fill_fw_str().
- Use sizeof() universally instead of using unbound defines.
- Fix bnx2x_7101_format_ver() and bnx2x_null_format_ver() to report the
number of characters written, not including the trailing %NUL (as
already done with the other firmware formatting functions).
- Require space for at least 1 byte in bnx2x_get_ext_phy_fw_version()
for the trailing %NUL.
- Correct the needed buffer size in bnx2x_3_seq_format_ver().
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401260858.jZN6vD1k-lkp@intel.com/
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240126041044.work.220-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
> ./drivers/ptp/ptp_sysfs.c:27:8-16: WARNING: please use sysfs_emit
No functional change intended
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20240125015329.123023-1-lizhijian@fujitsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Quoting from commit 4223f8651287 ("net: dsa: mt7530: make NET_DSA_MT7530
select MEDIATEK_GE_PHY"):
Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.
A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.
Now, the switch can be used without the PHYs but, at the moment, every
hardware design out there that I have seen uses them. For that, it would
make the most sense to force the selection of MEDIATEK_GE_PHY for the MDIO
interface which currently controls the MT7530 and MT7531 switches.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122053451.8004-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata updates from Niklas Cassel:
- Fix an incorrect link_power_management_policy sysfs attribute value.
We were previously using the same attribute value for two different
LPM policies (me)
- Add a ASMedia ASM1166 quirk.
The SATA host controller always reports that it has 32 ports, even
though it only has six ports. Add a quirk that overrides the value
reported by the controller (Conrad)
- Add a ASMedia ASM1061 quirk.
The SATA host controller completely ignores the upper 21 bits of the
DMA address. This causes IOMMU error events when a (valid) DMA
address actually has any of the upper 21 bits set. Add a quirk that
limits the dma_mask to 43-bits (Lennert)
* tag 'ata-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers
ahci: asm1166: correct count of reported ports
ata: libata-sata: improve sysfs description for ATA_LPM_UNKNOWN
|
|
Pull block fixes from Jens Axboe:
- RCU warning fix for md (Mikulas)
- Fix for an aoe issue that lockdep rightfully complained about
(Maksim)
- Fix for an error code change in partitioning that caused a regression
with some tools (Li)
- Fix for a data direction warning with bi-direction commands
(Christian)
* tag 'block-6.8-2024-01-26' of git://git.kernel.dk/linux:
md: fix a suspicious RCU usage warning
aoe: avoid potential deadlock at set_capacity
block: Fix WARNING in _copy_from_iter
block: Move checking GENHD_FL_NO_PART to bdev_add_partition()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control update from Rafael Wysocki:
"Remove some dead code from the Intel powerclamp thermal control driver
(Srinivas Pandruvada)"
* tag 'thermal-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: powerclamp: Remove dead code for target mwait value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two cpufreq drivers and the cpupower utility.
Specifics:
- Fix the handling of scaling_max/min_freq sysfs attributes in the
AMD P-state cpufreq driver (Mario Limonciello)
- Make the intel_pstate cpufreq driver avoid unnecessary computation
of the HWP performance level corresponding to a given frequency in
the cases when it is known already, which also helps to avoid
reducing the maximum CPU capacity artificially on some systems
(Rafael J. Wysocki)
- Fix compilation of the cpupower utility when CFLAGS is passed as a
make argument for cpupower, but it does not take effect as expected
due to mishandling (Stanley Chan)"
* tag 'pm-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq/amd-pstate: Fix setting scaling max/min freq values
cpufreq: intel_pstate: Refine computation of P-state for given frequency
tools cpupower bench: Override CFLAGS assignments
|
|
Setup PMCR port register for actual speed and duplex on internally
connected PHYs of the MT7988 built-in switch. This fixes links with
speeds other than 1000M.
Fixes: 110c18bfed41 ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/a5b04dfa8256d8302f402545a51ac4c626fdba25.1706071272.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
commit 056bce63c469 ("bnxt_en: Make PTP TX timestamp HWRM query silent")
changed a netdev_err() to netdev_WARN_ONCE().
netdev_WARN_ONCE() is it generates a kernel WARNING, which is bad, for
the following reasons:
* You do not a kernel warning if the firmware queries are late
* In busy networks, timestamp query failures fairly regularly
* A WARNING message doesn't bring much value, since the code path
is clear.
(This was discussed in-depth in [1])
Transform the netdev_WARN_ONCE() into a netdev_warn_once(), and print a
more well-behaved message, instead of a full WARN().
bnxt_en 0000:67:00.0 eth0: TS query for TX timer failed rc = fffffff5
[1] Link: https://lore.kernel.org/all/ZbDj%2FFI4EJezcfd1@gmail.com/
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Fixes: 056bce63c469 ("bnxt_en: Make PTP TX timestamp HWRM query silent")
Link: https://lore.kernel.org/r/20240125134104.2045573-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull drm fixes from Dave Airlie:
"Lots going on for rc2, ivpu has a bunch of stabilisation and debugging
work, then amdgpu and xe are the main fixes. i915, exynos have a few,
then some misc panel and bridge fixes.
Worth mentioning are three regressions. One of the nouveau fixes in
6.7 for a serious deadlock had side effects, so I guess we will bring
back the deadlock until I can figure out what should be done properly.
There was a scheduler regression vs amdgpu which was reported in a few
places and is now fixed. There was an i915 vs simpledrm problem
resulting in black screens, that is reverted also.
I'll be working on a proper nouveau fix, it kinda looks like one of
those cases where someone tried to use an atomic where they should
have probably used a lock, but I'll see.
fb:
- fix simpledrm/i915 regression by reverting change
scheduler:
- fix regression affecting amdgpu users due to sched draining
nouveau:
- revert 6.7 deadlock fix as it has side effects
dp:
- fix documentation warning
ttm:
- fix dummy page read on some platforms
bridge:
- anx7625 suspend fix
- sii902x: fix probing and audio registration
- parade-ps8640: fix suspend of bridge, aux fixes
- samsung-dsim: avoid using FORCE_STOP_STATE
panel:
- simple add missing bus flags
- fix samsung-s6d7aa0 flags
amdgpu:
- AC/DC power supply tracking fix
- Don't show invalid vram vendor data
- SMU 13.0.x fixes
- GART fix for umr on systems without VRAM
- GFX 10/11 UNORD_DISPATCH fixes
- IPS display fixes (required for S0ix on some platforms)
- Misc fixes
i915:
- DSI sequence revert to fix GitLab #10071 and DP test-pattern fix
- Drop -Wstringop-overflow (broken on GCC11)
ivpu:
- fix recovery/reset support
- improve submit ioctl stability
- fix dev open/close races on unbind
- PLL disable reset fix
- deprecate context priority param
- improve debug buffer logging
- disable buffer sharing across VPU contexts
- free buffer sgt on unbind
- fix missing lock around shmem vmap
- add better boot diagnostics
- add more debug prints around mapping
- dump MMU events in case of timeout
v3d:
- NULL ptr dereference fix
exynos:
- fix stack usage
- fix incorrect type
- fix dt typo
- fix gsc runtime resume
xe:
- Make an ops struct static
- Fix an implicit 0 to NULL conversion
- A couple of 32-bit fixes
- A migration coherency fix for Lunar Lake.
- An error path vm id leak fix
- Remove PVC references in kunit tests"
* tag 'drm-fixes-2024-01-27' of git://anongit.freedesktop.org/drm/drm: (66 commits)
Revert "nouveau: push event block/allowing out of the fence context"
drm: bridge: samsung-dsim: Don't use FORCE_STOP_STATE
drm/sched: Drain all entities in DRM sched run job worker
drm/amd/display: "Enable IPS by default"
drm/amd: Add a DC debug mask for IPS
drm/amd/display: Disable ips before dc interrupt setting
drm/amd/display: Replay + IPS + ABM in Full Screen VPB
drm/amd/display: Add IPS checks before dcn register access
drm/amd/display: Add Replay IPS register for DMUB command table
drm/amd/display: Allow IPS2 during Replay
drm/amdgpu/gfx11: set UNORD_DISPATCH in compute MQDs
drm/amdgpu/gfx10: set UNORD_DISPATCH in compute MQDs
drm/amd/amdgpu: Assign GART pages to AMD device mapping
drm/amd/pm: Fetch current power limit from FW
drm/amdgpu: Fix null pointer dereference
drm/amdgpu: Show vram vendor only if available
drm/amd/pm: update the power cap setting
drm/amdgpu: Avoid fetching vram vendor information
drm/amdgpu/pm: Fix the power source flag error
drm/amd/display: Fix uninitialized variable usage in core_link_ 'read_dpcd() & write_dpcd()' functions
...
|
|
is up"
This reverts commit b43f7ddc2b7a5a90447d96cb4d3c6d142dd4a810.
The offending commit deferred power-supply class device registration
until the service-started notification is received.
This triggers a NULL pointer dereference during boot of the Lenovo
ThinkPad X13s and SC8280XP CRD as battery status notifications can be
received before the service-start notification:
Unable to handle kernel NULL pointer dereference at virtual address 00000000000005c0
...
Call trace:
_acquire+0x338/0x2064
acquire+0x1e8/0x318
spin_lock_irqsave+0x60/0x88
_supply_changed+0x2c/0xa4
battmgr_callback+0x1d4/0x60c [qcom_battmgr]
pmic_glink_rpmsg_callback+0x5c/0xa4 [pmic_glink]
qcom_glink_native_rx+0x58c/0x7e8
qcom_glink_smem_intr+0x14/0x24 [qcom_glink_smem]
__handle_irq_event_percpu+0xb0/0x2d4
handle_irq_event+0x4c/0xb8
As trying to serialise this is non-trivial and risks missing
notifications, let's revert to registration during probe so that the
driver data is all set up once the service goes live.
The warning message during resume in case the aDSP firmware is not
running that motivated the change can be considered a feature and should
not be suppressed.
Fixes: b43f7ddc2b7a ("power: supply: qcom_battmgr: Register the power supplies after PDR is up")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240123160053.18331-1-johan+linaro@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull arm SoC fixes from Arnd Bergmann:
"There are a couple of devicetree fixes for samsung, riscv/sophgo, and
for TPM device nodes on a couple of platforms.
Both the Arm FF-A and the SCMI firmware drivers get a number of code
fixes, addressing minor implementation bugs and compatibility with
firmware implementations. Most of these bugs relate to the usage of
xarray and rwlock structures and are fixed by Cristian Marussi"
* tag 'arm-fixes-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
riscv: dts: sophgo: separate sg2042 mtime and mtimecmp to fit aclint format
arm64: dts: Fix TPM schema violations
ARM: dts: Fix TPM schema violations
ARM: dts: exynos4212-tab3: add samsung,invert-vclk flag to fimd
arm64: dts: exynos: gs101: comply with the new cmu_misc clock names
firmware: arm_ffa: Handle partitions setup failures
firmware: arm_ffa: Use xa_insert() and check for result
firmware: arm_ffa: Simplify ffa_partitions_cleanup()
firmware: arm_ffa: Check xa_load() return value
firmware: arm_ffa: Add missing rwlock_init() for the driver partition
firmware: arm_ffa: Add missing rwlock_init() in ffa_setup_partitions()
firmware: arm_scmi: Fix the clock protocol supported version
firmware: arm_scmi: Fix the clock protocol version for v3.2
firmware: arm_scmi: Use xa_insert() when saving raw queues
firmware: arm_scmi: Use xa_insert() to store opps
firmware: arm_scmi: Replace asm-generic/bug.h with linux/bug.h
firmware: arm_scmi: Check mailbox/SMT channel for consistency
|
|
The commit 1feb31e810b0 ("hwmon: (pmbus/mp2975) Simplify VOUT code")
has introduced a bug that makes it impossible to initialize MP2975
device:
"""
mp2975 5-0020: Failed to identify chip capabilities
i2c i2c-5: new_device: Instantiated device mp2975 at 0x20
i2c i2c-5: delete_device: Deleting device mp2975 at 0x20
"""
Since the 'read_byte_data' function was removed from the
'pmbus_driver_info ' structure the driver no longer reports correctly
that VOUT mode is direct. Therefore 'pmbus_identify_common' fails
with error, making it impossible to initialize the device.
Restore 'read_byte_data' function to fix the issue.
Tested:
- before: it is not possible to initialize MP2975 device with the
'mp2975' driver,
- after: 'mp2975' correctly initializes MP2975 device and all sensor
data is correct.
Fixes: 1feb31e810b0 ("hwmon: (pmbus/mp2975) Simplify VOUT code")
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Link: https://lore.kernel.org/r/20240126205714.2363-1-aladyshev22@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"As well as a few device IDs and the usual scattering of driver
specific fixes this contains a couple of core things.
One is a missed case in error handling, the other patch is a change
from me raising the number of chip selects allowed by the newly added
multi chip select support patches to resolve problems seen on several
systems that exceeded the limit.
This is not a real solution to the issue but rather just a change to
avoid disruption to users, one of the options I am considering is just
sending a revert of those changes if we can't come up with something
sensible"
* tag 'spi-fix-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fix finalize message on error return
spi: cs42l43: Handle error from devm_pm_runtime_enable
spi: Raise limit on number of chip selects
spi: hisi-sfc-v3xx: Return IRQ_NONE if no interrupts were detected
spi: spi-cadence: Reverse the order of interleaved write and read operations
spi: spi-imx: Use dev_err_probe for failed DMA channel requests
spi: bcm-qspi: fix SFDP BFPT read by usig mspi read
spi: intel-pci: Add support for Arrow Lake SPI serial flash
spi: intel-pci: Remove Meteor Lake-S SoC PCI ID from the list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- add a quirk to GPIO ACPI handling to ignore touchpad wakeups on GPD
G1619-04
- clear interrupt status bits (that may have been set before enabling
the interrupts) after setting the interrupt type in gpio-eic-sprd
* tag 'gpio-fixes-for-v6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: eic-sprd: Clear interrupt after set the interrupt type
gpiolib: acpi: Ignore touchpad wakeup on GPD G1619-04
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- remove K3 DT prefix from wave5
- vb2 core: fix missing caps on VIDIO_CREATE_BUFS under certain
circumstances
- videobuf2: Stop direct calls to queue num_buffers field
* tag 'media/v6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: vb2: refactor setting flags and caps, fix missing cap
media: media videobuf2: Stop direct calls to queue num_buffers field
media: chips-media: wave5: Remove K3 References
dt-bindings: media: Remove K3 Family Prefix from Compatible
|
|
Add touch screen info for TECLAST X16 Plus tablet.
Signed-off-by: Phoenix Chen <asbeltogf@gmail.com>
Link: https://lore.kernel.org/r/20240126095308.5042-1-asbeltogf@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Missing release_firmware() due to error handling blocked any future image
loading.
Fix the return code and release_fiwmare() to release the bad image.
Fixes: 25a76dbb36dd ("platform/x86/intel/ifs: Validate image size")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240125082254.424859-2-ashok.raj@intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
amd_pmf_get_pb_data() will allocate memory for the policy buffer,
but does not free it if copy_from_user() fails. This leads to a memory
leak.
Fixes: 10817f28e533 ("platform/x86/amd/pmf: Add capability to sideload of policy binary")
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Cong Liu <liucong2@kylinos.cn>
Link: https://lore.kernel.org/r/20240124012939.6550-1-liucong2@kylinos.cn
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
AMD SFH driver has APIs defined to export the ambient light information;
use this within the PMF driver to send inputs to the PMF TA, so that PMF
driver can enact to the actions coming from the TA.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240123141458.3715211-2-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
AMD SFH driver has APIs defined to export the human presence information;
use this within the PMF driver to send inputs to the PMF TA, so that PMF
driver can enact to the actions coming from the TA.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240123141458.3715211-1-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Goto 'unlock_and_return' for unlocking before returning on the error
path.
Fixes: d5939a793693 ("hwmon: Add driver for Gigabyte AORUS Waterforce AIO coolers")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20240122154952.2851934-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
One regression fixup to samsung-dsim.c module
- The FORCE_STOP_STATE bit is ineffective for forcing DSI link into LP-11 mode,
causing timing issues and potential bridge failures.
This patch reverts previous commits and corrects this issue.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126141130.15512-1-inki.dae@samsung.com
|
|
This reverts commit eacabb5462717a52fccbbbba458365a4f5e61f35.
This commit causes some regressions in desktop usage, this will
reintroduce the original deadlock in DRI_PRIME situations, I've
got an idea to fix it by offloading to a workqueue in a different
spot, however this code has a race condition where we sometimes
miss interrupts so I'd like to fix that as well.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
