summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2023-03-17bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type changeNikolay Aleksandrov
Add bond_ether_setup helper which is used to fix ether_setup() calls in the bonding driver. It takes care of both IFF_MASTER and IFF_SLAVE flags, the former is always restored and the latter only if it was set. If the bond enslaves non-ARPHRD_ETHER device (changes its type), then releases it and enslaves ARPHRD_ETHER device (changes back) then we use ether_setup() to restore the bond device type but it also resets its flags and removes IFF_MASTER and IFF_SLAVE[1]. Use the bond_ether_setup helper to restore both after such transition. [1] reproduce (nlmon is non-ARPHRD_ETHER): $ ip l add nlmon0 type nlmon $ ip l add bond2 type bond mode active-backup $ ip l set nlmon0 master bond2 $ ip l set nlmon0 nomaster $ ip l add bond1 type bond (we use bond1 as ARPHRD_ETHER device to restore bond2's mode) $ ip l set bond1 master bond2 $ ip l sh dev bond2 37: bond2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether be:d7:c5:40:5b:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500 (notice bond2's IFF_MASTER is missing) Fixes: e36b9d16c6a6 ("bonding: clean muticast addresses when device changes type") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-17net: renesas: rswitch: Fix GWTSDIE register handlingYoshihiro Shimoda
Since the GWCA has the TX timestamp feature, this driver should not disable it if one of ports is opened. So, fix it. Reported-by: Phong Hoang <phong.hoang.wz@renesas.com> Fixes: 33f5d733b589 ("net: renesas: rswitch: Improve TX timestamp accuracy") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-17net: renesas: rswitch: Fix the output value of quote from rswitch_rx()Yoshihiro Shimoda
If the RX descriptor doesn't have any data, the output value of quote from rswitch_rx() will be increased unexpectedily. So, fix it. Reported-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com> Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-17ethernet: sun: add check for the mdesc_grab()Liang He
In vnet_port_probe() and vsw_port_probe(), we should check the return value of mdesc_grab() as it may return NULL which can caused NPD bugs. Fixes: 5d01fa0c6bd8 ("ldmvsw: Add ldmvsw.c driver code") Fixes: 43fdf27470b2 ("[SPARC64]: Abstract out mdesc accesses for better MD update handling.") Signed-off-by: Liang He <windhl@126.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-17drm/ttm: drop extra ttm_bo_put in ttm_bo_cleanup_refsChristian König
That was accidentially left over when we switched to the delayed delete worker. Suggested-by: Matthew Auld <matthew.william.auld@gmail.com> Signed-off-by: Christian König <christian.koenig@amd.com> Fixes: 9bff18d13473 ("drm/ttm: use per BO cleanup workers") Reported-by: Steven Rostedt (Google) <rostedt@goodmis.org> Tested-by: Steven Rostedt (Google) <rostedt@goodmis.org> Reviewed-by: Matthew Auld <matthew.auld@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230316072647.406707-1-christian.koenig@amd.com
2023-03-17Merge tag 'amd-drm-fixes-6.3-2023-03-15' of ↵Dave Airlie
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes amd-drm-fixes-6.3-2023-03-15: amdgpu: - SMU 13 update - RDNA2 suspend/resume fix when overclocking is enabled - SRIOV VCN fixes - HDCP suspend/resume fix - Fix drm polling splat regression - Fix dirty rectangle tracking for PSR - Fix vangogh regression on certain BIOSes - Misc display fixes - Suspend/resume IOMMU regression fix amdkfd: - Fix BO offset for multi-VMA page migration - Fix a possible double free - Fix potential use after free - Fix process cleanup on module exit Signed-off-by: Dave Airlie <airlied@redhat.com> From: Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230315224400.7558-1-alexander.deucher@amd.com
2023-03-16net: ipa: fix some register validity checksAlex Elder
A recent commit defined HW_PARAM_4 as a GSI register ID but did not add it to gsi_reg_id_valid() to indicate it's valid (for IPA v5.0+). Add version checks for the HW_PARAM_2 and INTER_EE IRQ GSI registers there as well. IPA v5.0 supports up to 8 source and destination resource groups. Update the validity check (and the comments where the register IDs are defined) to reflect that. Similarly update comments and validity checks for the hash/cache-related registers. Note that this patch fixes an omission and constrains things further, but these don't technically represent bugs. Fixes: f651334e1ef5 ("net: ipa: add HW_PARAM_4 GSI register") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16net: ipa: kill FILT_ROUT_CACHE_CFG IPA registerAlex Elder
A recent commit defined a few IPA registers used for IPA v5.0+. One of those was a mistake. Although the filter and router caches get *flushed* using a single register, they use distinct registers (ENDP_FILTER_CACHE_CFG and ENDP_ROUTER_CACHE_CFG) for configuration. And although there *exists* a FILT_ROUT_CACHE_CFG register, it is not needed in upstream code. So get rid of definitions related to FILT_ROUT_CACHE_CFG, because they are not needed. Fixes: 8ba59716d16a ("net: ipa: define IPA v5.0+ registers") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16net: ipa: add two missing declarationsAlex Elder
When gsi_reg_init() got added, its declaration was added to "gsi_reg.h" without declaring the two struct pointer types it uses. Add these struct declarations to "gsi_reg.h". Fixes: 3c506add35c7 ("net: ipa: introduce gsi_reg_init()") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16net: ipa: reg: include <linux/bug.h>Alex Elder
When "reg.h" got created, it included calls to WARN() and WARN_ON(). Those macros are defined via <linux/bug.h>. In addition, it uses is_power_of_2(), which is defined in <linux/log2.h>. Include those files so IPA "reg.h" has access to all definitions it requires. Meanwhile, <linux/bits.h> is included but nothing defined therein is required directly in "reg.h", so get rid of that. Fixes: 81772e444dbe ("net: ipa: start generalizing "ipa_reg"") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16net: dsa: microchip: fix RGMII delay configuration on KSZ8765/KSZ8794/KSZ8795Marek Vasut
The blamed commit has replaced a ksz_write8() call to address REG_PORT_5_CTRL_6 (0x56) with a ksz_set_xmii() -> ksz_pwrite8() call to regs[P_XMII_CTRL_1], which is also defined as 0x56 for ksz8795_regs[]. The trouble is that, when compared to ksz_write8(), ksz_pwrite8() also adjusts the register offset with the port base address. So in reality, ksz_pwrite8(offset=0x56) accesses register 0x56 + 0x50 = 0xa6, which in this switch appears to be unmapped, and the RGMII delay configuration on the CPU port does nothing. So if the switch wasn't fine with the RGMII delay configuration done through pin strapping and relied on Linux to apply a different one in order to pass traffic, this is now broken. Using the offset translation logic imposed by ksz_pwrite8(), the correct value for regs[P_XMII_CTRL_1] should have been 0x6 on ksz8795_regs[], in order to really end up accessing register 0x56. Static code analysis shows that, despite there being multiple other accesses to regs[P_XMII_CTRL_1] in this driver, the only code path that is applicable to ksz8795_regs[] and ksz8_dev_ops is ksz_set_xmii(). Therefore, the problem is isolated to RGMII delays. In its current form, ksz8795_regs[] contains the same value for P_XMII_CTRL_0 and for P_XMII_CTRL_1, and this raises valid suspicions that writes made by the driver to regs[P_XMII_CTRL_0] might overwrite writes made to regs[P_XMII_CTRL_1] or vice versa. Again, static analysis shows that the only accesses to P_XMII_CTRL_0 from the driver are made from code paths which are not reachable with ksz8_dev_ops. So the accesses made by ksz_set_xmii() are safe for this switch family. [ vladimiroltean: rewrote commit message ] Fixes: c476bede4b0f ("net: dsa: microchip: ksz8795: use common xmii function") Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230315231916.2998480-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16Merge tag 'mlx5-fixes-2023-03-15' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5 fixes 2023-03-15 This series provides bug fixes to mlx5 driver. * tag 'mlx5-fixes-2023-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5e: TC, Remove error message log print net/mlx5e: TC, fix cloned flow attribute net/mlx5e: TC, fix missing error code net/sched: TC, fix raw counter initialization net/mlx5e: Lower maximum allowed MTU in XSK to match XDP prerequisites net/mlx5: Set BREAK_FW_WAIT flag first when removing driver net/mlx5e: kTLS, Fix missing error unwind on unsupported cipher type net/mlx5e: Fix cleanup null-ptr deref on encap lock net/mlx5: E-switch, Fix missing set of split_count when forward to ovs internal port net/mlx5: E-switch, Fix wrong usage of source port rewrite in split rules net/mlx5: Disable eswitch before waiting for VF pages net/mlx5: Fix setting ec_function bit in MANAGE_PAGES net/mlx5e: Don't cache tunnel offloads capability net/mlx5e: Fix macsec ASO context alignment ==================== Link: https://lore.kernel.org/r/20230315225847.360083-1-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16qed/qed_mng_tlv: correctly zero out ->min instead of ->hourDaniil Tatianin
This fixes an issue where ->hour would erroneously get zeroed out instead of ->min because of a bad copy paste. Found by Linux Verification Center (linuxtesting.org) with the SVACE static analysis tool. Fixes: f240b6882211 ("qed: Add support for processing fcoe tlv request.") Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru> Link: https://lore.kernel.org/r/20230315194618.579286-1-d-tatianin@yandex-team.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16scsi: scsi_dh_alua: Fix memleak for 'qdata' in alua_activate()Yu Kuai
If alua_rtpg_queue() failed from alua_activate(), then 'qdata' is not freed, which will cause following memleak: unreferenced object 0xffff88810b2c6980 (size 32): comm "kworker/u16:2", pid 635322, jiffies 4355801099 (age 1216426.076s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 40 39 24 c1 ff ff ff ff 00 f8 ea 0a 81 88 ff ff @9$............. backtrace: [<0000000098f3a26d>] alua_activate+0xb0/0x320 [<000000003b529641>] scsi_dh_activate+0xb2/0x140 [<000000007b296db3>] activate_path_work+0xc6/0xe0 [dm_multipath] [<000000007adc9ace>] process_one_work+0x3c5/0x730 [<00000000c457a985>] worker_thread+0x93/0x650 [<00000000cb80e628>] kthread+0x1ba/0x210 [<00000000a1e61077>] ret_from_fork+0x22/0x30 Fix the problem by freeing 'qdata' in error path. Fixes: 625fe857e4fa ("scsi: scsi_dh_alua: Check scsi_device_get() return value") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20230315062154.668812-1-yukuai1@huaweicloud.com Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-03-16scsi: qla2xxx: Synchronize the IOCB count to be in orderQuinn Tran
A system hang was observed with the following call trace: BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 15 PID: 86747 Comm: nvme Kdump: loaded Not tainted 6.2.0+ #1 Hardware name: Dell Inc. PowerEdge R6515/04F3CJ, BIOS 2.7.3 03/31/2022 RIP: 0010:__wake_up_common+0x55/0x190 Code: 41 f6 01 04 0f 85 b2 00 00 00 48 8b 43 08 4c 8d 40 e8 48 8d 43 08 48 89 04 24 48 89 c6\ 49 8d 40 18 48 39 c6 0f 84 e9 00 00 00 <49> 8b 40 18 89 6c 24 14 31 ed 4c 8d 60 e8 41 8b 18 f6 c3 04 75 5d RSP: 0018:ffffb05a82afbba0 EFLAGS: 00010082 RAX: 0000000000000000 RBX: ffff8f9b83a00018 RCX: 0000000000000000 RDX: 0000000000000001 RSI: ffff8f9b83a00020 RDI: ffff8f9b83a00018 RBP: 0000000000000001 R08: ffffffffffffffe8 R09: ffffb05a82afbbf8 R10: 70735f7472617473 R11: 5f30307832616c71 R12: 0000000000000001 R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000 FS: 00007f815cf4c740(0000) GS:ffff8f9eeed80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000010633a000 CR4: 0000000000350ee0 Call Trace: <TASK> __wake_up_common_lock+0x83/0xd0 qla_nvme_ls_req+0x21b/0x2b0 [qla2xxx] __nvme_fc_send_ls_req+0x1b5/0x350 [nvme_fc] nvme_fc_xmt_disconnect_assoc+0xca/0x110 [nvme_fc] nvme_fc_delete_association+0x1bf/0x220 [nvme_fc] ? nvme_remove_namespaces+0x9f/0x140 [nvme_core] nvme_do_delete_ctrl+0x5b/0xa0 [nvme_core] nvme_sysfs_delete+0x5f/0x70 [nvme_core] kernfs_fop_write_iter+0x12b/0x1c0 vfs_write+0x2a3/0x3b0 ksys_write+0x5f/0xe0 do_syscall_64+0x5c/0x90 ? syscall_exit_work+0x103/0x130 ? syscall_exit_to_user_mode+0x12/0x30 ? do_syscall_64+0x69/0x90 ? exit_to_user_mode_loop+0xd0/0x130 ? exit_to_user_mode_prepare+0xec/0x100 ? syscall_exit_to_user_mode+0x12/0x30 ? do_syscall_64+0x69/0x90 ? syscall_exit_to_user_mode+0x12/0x30 ? do_syscall_64+0x69/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7f815cd3eb97 The IOCB counts are out of order and that would block any commands from going out and subsequently hang the system. Synchronize the IOCB count to be in correct order. Fixes: 5f63a163ed2f ("scsi: qla2xxx: Fix exchange oversubscription for management commands") Cc: stable@vger.kernel.org Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Nilesh Javali <njavali@marvell.com> Link: https://lore.kernel.org/r/20230313043711.13500-3-njavali@marvell.com Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: Lin Li <lilin@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-03-16scsi: qla2xxx: Perform lockless command completion in abort pathNilesh Javali
While adding and removing the controller, the following call trace was observed: WARNING: CPU: 3 PID: 623596 at kernel/dma/mapping.c:532 dma_free_attrs+0x33/0x50 CPU: 3 PID: 623596 Comm: sh Kdump: loaded Not tainted 5.14.0-96.el9.x86_64 #1 RIP: 0010:dma_free_attrs+0x33/0x50 Call Trace: qla2x00_async_sns_sp_done+0x107/0x1b0 [qla2xxx] qla2x00_abort_srb+0x8e/0x250 [qla2xxx] ? ql_dbg+0x70/0x100 [qla2xxx] __qla2x00_abort_all_cmds+0x108/0x190 [qla2xxx] qla2x00_abort_all_cmds+0x24/0x70 [qla2xxx] qla2x00_abort_isp_cleanup+0x305/0x3e0 [qla2xxx] qla2x00_remove_one+0x364/0x400 [qla2xxx] pci_device_remove+0x36/0xa0 __device_release_driver+0x17a/0x230 device_release_driver+0x24/0x30 pci_stop_bus_device+0x68/0x90 pci_stop_and_remove_bus_device_locked+0x16/0x30 remove_store+0x75/0x90 kernfs_fop_write_iter+0x11c/0x1b0 new_sync_write+0x11f/0x1b0 vfs_write+0x1eb/0x280 ksys_write+0x5f/0xe0 do_syscall_64+0x5c/0x80 ? do_user_addr_fault+0x1d8/0x680 ? do_syscall_64+0x69/0x80 ? exc_page_fault+0x62/0x140 ? asm_exc_page_fault+0x8/0x30 entry_SYSCALL_64_after_hwframe+0x44/0xae The command was completed in the abort path during driver unload with a lock held, causing the warning in abort path. Hence complete the command without any lock held. Reported-by: Lin Li <lilin@redhat.com> Tested-by: Lin Li <lilin@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Nilesh Javali <njavali@marvell.com> Link: https://lore.kernel.org/r/20230313043711.13500-2-njavali@marvell.com Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-03-16scsi: core: Add BLIST_SKIP_VPD_PAGES for SKhynix H28U74301AMRJoel Selvaraj
Xiaomi Poco F1 (qcom/sdm845-xiaomi-beryllium*.dts) comes with a SKhynix H28U74301AMR UFS. The sd_read_cpr() operation leads to a 120 second timeout, making the device bootup very slow: [ 121.457736] sd 0:0:0:1: [sdb] tag#23 timing out command, waited 120s Setting the BLIST_SKIP_VPD_PAGES allows the device to skip the failing sd_read_cpr operation and boot normally. Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com> Link: https://lore.kernel.org/r/20230313041402.39330-1-joelselvaraj.oss@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-03-17Merge tag 'drm-intel-fixes-2023-03-15' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes drm/i915 fixes for v6.3-rc3: - Fix hwmon PL1 power limit enabling - Fix audio ELD handling for DP MST - Fix PSR io and wake line calculations - Fix DG2 HDMI modes with 267.30 and 319.89 MHz pixel clocks - Fix SSEU subslice out-of-bounds access - Fix misuse of non-idle barriers as fence trackers Signed-off-by: Dave Airlie <airlied@redhat.com> From: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/87r0tq5nyn.fsf@intel.com
2023-03-16i825xx: sni_82596: use eth_hw_addr_set()Thomas Bogendoerfer
netdev->dev_addr is now const, we can't write to it directly. Copy scrambled mac address octects into an array then eth_hw_addr_set(). Fixes: adeef3e32146 ("net: constify netdev->dev_addr") Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Link: https://lore.kernel.org/r/20230315134117.79511-1-tsbogend@alpha.franken.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16net: atlantic: Fix crash when XDP is enabled but no program is loadedToke Høiland-Jørgensen
The aq_xdp_run_prog() function falls back to the XDP_ABORTED action handler (using a goto) if the operations for any of the other actions fail. The XDP_ABORTED handler in turn calls the bpf_warn_invalid_xdp_action() tracepoint. However, the function also jumps into the XDP_PASS helper if no XDP program is loaded on the device, which means the XDP_ABORTED handler can be run with a NULL program pointer. This results in a NULL pointer deref because the tracepoint dereferences the 'prog' pointer passed to it. This situation can happen in multiple ways: - If a packet arrives between the removal of the program from the interface and the static_branch_dec() in aq_xdp_setup() - If there are multiple devices using the same driver in the system and one of them has an XDP program loaded and the other does not. Fix this by refactoring the aq_xdp_run_prog() function to remove the 'goto pass' handling if there is no XDP program loaded. Instead, factor out the skb building in a separate small helper function. Fixes: 26efaef759a1 ("net: atlantic: Implement xdp data plane") Reported-by: Freysteinn Alfredsson <Freysteinn.Alfredsson@kau.se> Tested-by: Freysteinn Alfredsson <Freysteinn.Alfredsson@kau.se> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20230315125539.103319-1-toke@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16net: usb: smsc75xx: Move packet length check to prevent kernel panic in skb_pullSzymon Heidrich
Packet length check needs to be located after size and align_count calculation to prevent kernel panic in skb_pull() in case rx_cmd_a & RX_CMD_A_RED evaluates to true. Fixes: d8b228318935 ("net: usb: smsc75xx: Limit packet length to skb->len") Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com> Link: https://lore.kernel.org/r/20230316110540.77531-1-szymon.heidrich@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16sh_eth: avoid PHY being resumed when interface is not upWolfram Sang
SH_ETH doesn't need mdiobus suspend/resume, that's why it sets 'mac_managed_pm'. However, setting it needs to be moved from init to probe, so mdiobus PM functions will really never be called (e.g. when the interface is not up yet during suspend/resume). Fixes: 6a1dbfefdae4 ("net: sh_eth: Fix PHY state warning splat during system resume") Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16ravb: avoid PHY being resumed when interface is not upWolfram Sang
RAVB doesn't need mdiobus suspend/resume, that's why it sets 'mac_managed_pm'. However, setting it needs to be moved from init to probe, so mdiobus PM functions will really never be called (e.g. when the interface is not up yet during suspend/resume). Fixes: 4924c0cdce75 ("net: ravb: Fix PHY state warning splat during system resume") Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-16i2c: xgene-slimpro: Fix out-of-bounds bug in xgene_slimpro_i2c_xfer()Wei Chen
The data->block[0] variable comes from user and is a number between 0-255. Without proper check, the variable may be very large to cause an out-of-bounds when performing memcpy in slimpro_i2c_blkwr. Fix this bug by checking the value of writelen. Fixes: f6505fbabc42 ("i2c: add SLIMpro I2C device driver on APM X-Gene platform") Signed-off-by: Wei Chen <harperchen1110@gmail.com> Cc: stable@vger.kernel.org Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-03-16drm/format-helper: Make "destination_pitch" test usable for monoArthur Grillo
This test case uses an arbitrary pitch size, different of the default one, to test if the conversions methods obey. Change the "destination_pitch" colors to change the monochrome expected result from being just zeros, as this makes the arbitrary pitch use unusable. Signed-off-by: Arthur Grillo <arthurgrillo@riseup.net> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230311125141.564801-3-arthurgrillo@riseup.net
2023-03-16i2c: hisi: Only use the completion interrupt to finish the transferYicong Yang
The controller will always generate a completion interrupt when the transfer is finished normally or not. Currently we use either error or completion interrupt to finish, this may result the completion interrupt unhandled and corrupt the next transfer, especially at low speed mode. Since on error case, the error interrupt will come first then is the completion interrupt. So only use the completion interrupt to finish the whole transfer process. Fixes: d62fbdb99a85 ("i2c: add support for HiSilicon I2C controller") Reported-by: Sheng Feng <fengsheng5@huawei.com> Signed-off-by: Sheng Feng <fengsheng5@huawei.com> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-03-16i2c: hisi: Avoid redundant interruptsYicong Yang
After issuing all the messages we can disable the TX_EMPTY interrupts to avoid handling redundant interrupts. For doing a sinlge bus detection (i2cdetect -y -r 0) we can reduce ~97% interrupts (before ~12000 after ~400). Signed-off-by: Sheng Feng <fengsheng5@huawei.com> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-03-16i2c: mxs: ensure that DMA buffers are safe for DMAMatthias Schiffer
We found that after commit 9c46929e7989 ("ARM: implement THREAD_INFO_IN_TASK for uniprocessor systems"), the PCF85063 RTC driver stopped working on i.MX28 due to regmap_bulk_read() reading bogus data into a stack buffer. This is caused by the i2c-mxs driver using DMA transfers even for messages without the I2C_M_DMA_SAFE flag, and the aforementioned commit enabling vmapped stacks. As the MXS I2C controller requires DMA for reads of >4 bytes, DMA can't be disabled, so the issue is fixed by using i2c_get_dma_safe_msg_buf() to create a bounce buffer when needed. Fixes: 9c46929e7989 ("ARM: implement THREAD_INFO_IN_TASK for uniprocessor systems") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-03-16i2c: imx-lpi2c: check only for enabled interrupt flagsAlexander Stein
When reading from I2C, the Tx watermark is set to 0. Unfortunately the TDF (transmit data flag) is enabled when Tx FIFO entries is equal or less than watermark. So it is set in every case, hence the reset default of 1. This results in the MSR_RDF _and_ MSR_TDF flags to be set thus trying to send Tx data on a read message. Mask the IRQ status to filter for wanted flags only. Fixes: a55fa9d0e42e ("i2c: imx-lpi2c: add low power i2c bus driver") Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-03-16drm/format-helper: Add Kunit tests for drm_fb_xrgb8888_to_mono()Arthur Grillo
Extend the existing test cases to test the conversion from XRGB8888 to monochromatic. Signed-off-by: Arthur Grillo <arthurgrillo@riseup.net> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230311125141.564801-2-arthurgrillo@riseup.net
2023-03-16i2c: imx-lpi2c: clean rx/tx buffers upon new messageAlexander Stein
When start sending a new message clear the Rx & Tx buffer pointers in order to avoid using stale pointers. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-03-16virtio_net: free xdp shinfo frags when build_skb_from_xdp_buff() failsXuan Zhuo
build_skb_from_xdp_buff() may return NULL, in this case we need to free the frags of xdp shinfo. Fixes: fab89bafa95b ("virtio-net: support multi-buffer xdp") Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-16virtio_net: fix page_to_skb() miss headroomXuan Zhuo
Because headroom is not passed to page_to_skb(), this causes the shinfo exceeds the range. Then the frags of shinfo are changed by other process. [ 157.724634] stack segment: 0000 [#1] PREEMPT SMP NOPTI [ 157.725358] CPU: 3 PID: 679 Comm: xdp_pass_user_f Tainted: G E 6.2.0+ #150 [ 157.726401] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/4 [ 157.727820] RIP: 0010:skb_release_data+0x11b/0x180 [ 157.728449] Code: 44 24 02 48 83 c3 01 39 d8 7e be 48 89 d8 48 c1 e0 04 41 80 7d 7e 00 49 8b 6c 04 30 79 0c 48 89 ef e8 89 b [ 157.730751] RSP: 0018:ffffc90000178b48 EFLAGS: 00010202 [ 157.731383] RAX: 0000000000000010 RBX: 0000000000000001 RCX: 0000000000000000 [ 157.732270] RDX: 0000000000000000 RSI: 0000000000000002 RDI: ffff888100dd0b00 [ 157.733117] RBP: 5d5d76010f6e2408 R08: ffff888100dd0b2c R09: 0000000000000000 [ 157.734013] R10: ffffffff82effd30 R11: 000000000000a14e R12: ffff88810981ffc0 [ 157.734904] R13: ffff888100dd0b00 R14: 0000000000000002 R15: 0000000000002310 [ 157.735793] FS: 00007f06121d9740(0000) GS:ffff88842fcc0000(0000) knlGS:0000000000000000 [ 157.736794] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 157.737522] CR2: 00007ffd9a56c084 CR3: 0000000104bda001 CR4: 0000000000770ee0 [ 157.738420] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 157.739283] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 157.740146] PKRU: 55555554 [ 157.740502] Call Trace: [ 157.740843] <IRQ> [ 157.741117] kfree_skb_reason+0x50/0x120 [ 157.741613] __udp4_lib_rcv+0x52b/0x5e0 [ 157.742132] ip_protocol_deliver_rcu+0xaf/0x190 [ 157.742715] ip_local_deliver_finish+0x77/0xa0 [ 157.743280] ip_sublist_rcv_finish+0x80/0x90 [ 157.743834] ip_list_rcv_finish.constprop.0+0x16f/0x190 [ 157.744493] ip_list_rcv+0x126/0x140 [ 157.744952] __netif_receive_skb_list_core+0x29b/0x2c0 [ 157.745602] __netif_receive_skb_list+0xed/0x160 [ 157.746190] ? udp4_gro_receive+0x275/0x350 [ 157.746732] netif_receive_skb_list_internal+0xf2/0x1b0 [ 157.747398] napi_gro_receive+0xd1/0x210 [ 157.747911] virtnet_receive+0x75/0x1c0 [ 157.748422] virtnet_poll+0x48/0x1b0 [ 157.748878] __napi_poll+0x29/0x1b0 [ 157.749330] net_rx_action+0x27a/0x340 [ 157.749812] __do_softirq+0xf3/0x2fb [ 157.750298] do_softirq+0xa2/0xd0 [ 157.750745] </IRQ> [ 157.751563] <TASK> [ 157.752329] __local_bh_enable_ip+0x6d/0x80 [ 157.753178] virtnet_xdp_set+0x482/0x860 [ 157.754159] ? __pfx_virtnet_xdp+0x10/0x10 [ 157.755129] dev_xdp_install+0xa4/0xe0 [ 157.756033] dev_xdp_attach+0x20b/0x5e0 [ 157.756933] do_setlink+0x82e/0xc90 [ 157.757777] ? __nla_validate_parse+0x12b/0x1e0 [ 157.758744] rtnl_setlink+0xd8/0x170 [ 157.759549] ? mod_objcg_state+0xcb/0x320 [ 157.760328] ? security_capable+0x37/0x60 [ 157.761209] ? security_capable+0x37/0x60 [ 157.762072] rtnetlink_rcv_msg+0x145/0x3d0 [ 157.762929] ? ___slab_alloc+0x327/0x610 [ 157.763754] ? __alloc_skb+0x141/0x170 [ 157.764533] ? __pfx_rtnetlink_rcv_msg+0x10/0x10 [ 157.765422] netlink_rcv_skb+0x58/0x110 [ 157.766229] netlink_unicast+0x21f/0x330 [ 157.766951] netlink_sendmsg+0x240/0x4a0 [ 157.767654] sock_sendmsg+0x93/0xa0 [ 157.768434] ? sockfd_lookup_light+0x12/0x70 [ 157.769245] __sys_sendto+0xfe/0x170 [ 157.770079] ? handle_mm_fault+0xe9/0x2d0 [ 157.770859] ? preempt_count_add+0x51/0xa0 [ 157.771645] ? up_read+0x3c/0x80 [ 157.772340] ? do_user_addr_fault+0x1e9/0x710 [ 157.773166] ? kvm_read_and_reset_apf_flags+0x49/0x60 [ 157.774087] __x64_sys_sendto+0x29/0x30 [ 157.774856] do_syscall_64+0x3c/0x90 [ 157.775518] entry_SYSCALL_64_after_hwframe+0x72/0xdc [ 157.776382] RIP: 0033:0x7f06122def70 Fixes: 18117a842ab0 ("virtio-net: remove xdp related info from page_to_skb()") Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-16net: Use of_property_read_bool() for boolean propertiesRob Herring
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. Convert reading boolean properties to of_property_read_bool(). Reviewed-by: Simon Horman <simon.horman@corigine.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can Acked-by: Kalle Valo <kvalo@kernel.org> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Reviewed-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-16net: dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290Vladimir Oltean
There are 3 classes of switch families that the driver is aware of, as far as mv88e6xxx_change_mtu() is concerned: - MTU configuration is available per port. Here, the chip->info->ops->port_set_jumbo_size() method will be present. - MTU configuration is global to the switch. Here, the chip->info->ops->set_max_frame_size() method will be present. - We don't know how to change the MTU. Here, none of the above methods will be present. Switch families MV88E6165, MV88E6191, MV88E6220, MV88E6250 and MV88E6290 fall in category 3. The blamed commit has adjusted the MTU for all 3 categories by EDSA_HLEN (8 bytes), resulting in a new maximum MTU of 1492 being reported by the driver for these switches. I don't have the hardware to test, but I do have a MV88E6390 switch on which I can simulate this by commenting out its .port_set_jumbo_size definition from mv88e6390_ops. The result is this set of messages at probe time: mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 1 mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 2 mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 3 mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 4 mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 5 mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 6 mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 7 mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 8 It is highly implausible that there exist Ethernet switches which don't support the standard MTU of 1500 octets, and this is what the DSA framework says as well - the error comes from dsa_slave_create() -> dsa_slave_change_mtu(slave_dev, ETH_DATA_LEN). But the error messages are alarming, and it would be good to suppress them. As a consequence of this unlikeliness, we reimplement mv88e6xxx_get_max_mtu() and mv88e6xxx_change_mtu() on switches from the 3rd category as follows: the maximum supported MTU is 1500, and any request to set the MTU to a value larger than that fails in dev_validate_mtu(). Fixes: b9c587fed61c ("dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-16dm stats: check for and propagate alloc_percpu failureJiasheng Jiang
Check alloc_precpu()'s return value and return an error from dm_stats_init() if it fails. Update alloc_dev() to fail if dm_stats_init() does. Otherwise, a NULL pointer dereference will occur in dm_stats_cleanup() even if dm-stats isn't being actively used. Fixes: fd2ed4d25270 ("dm: add statistics support") Cc: stable@vger.kernel.org Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
2023-03-16ice: xsk: disable txq irq before flushing hwMaciej Fijalkowski
ice_qp_dis() intends to stop a given queue pair that is a target of xsk pool attach/detach. One of the steps is to disable interrupts on these queues. It currently is broken in a way that txq irq is turned off *after* HW flush which in turn takes no effect. ice_qp_dis(): -> ice_qvec_dis_irq() --> disable rxq irq --> flush hw -> ice_vsi_stop_tx_ring() -->disable txq irq Below splat can be triggered by following steps: - start xdpsock WITHOUT loading xdp prog - run xdp_rxq_info with XDP_TX action on this interface - start traffic - terminate xdpsock [ 256.312485] BUG: kernel NULL pointer dereference, address: 0000000000000018 [ 256.319560] #PF: supervisor read access in kernel mode [ 256.324775] #PF: error_code(0x0000) - not-present page [ 256.329994] PGD 0 P4D 0 [ 256.332574] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 256.337006] CPU: 3 PID: 32 Comm: ksoftirqd/3 Tainted: G OE 6.2.0-rc5+ #51 [ 256.345218] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [ 256.355807] RIP: 0010:ice_clean_rx_irq_zc+0x9c/0x7d0 [ice] [ 256.361423] Code: b7 8f 8a 00 00 00 66 39 ca 0f 84 f1 04 00 00 49 8b 47 40 4c 8b 24 d0 41 0f b7 45 04 66 25 ff 3f 66 89 04 24 0f 84 85 02 00 00 <49> 8b 44 24 18 0f b7 14 24 48 05 00 01 00 00 49 89 04 24 49 89 44 [ 256.380463] RSP: 0018:ffffc900088bfd20 EFLAGS: 00010206 [ 256.385765] RAX: 000000000000003c RBX: 0000000000000035 RCX: 000000000000067f [ 256.393012] RDX: 0000000000000775 RSI: 0000000000000000 RDI: ffff8881deb3ac80 [ 256.400256] RBP: 000000000000003c R08: ffff889847982710 R09: 0000000000010000 [ 256.407500] R10: ffffffff82c060c0 R11: 0000000000000004 R12: 0000000000000000 [ 256.414746] R13: ffff88811165eea0 R14: ffffc9000d255000 R15: ffff888119b37600 [ 256.421990] FS: 0000000000000000(0000) GS:ffff8897e0cc0000(0000) knlGS:0000000000000000 [ 256.430207] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 256.436036] CR2: 0000000000000018 CR3: 0000000005c0a006 CR4: 00000000007706e0 [ 256.443283] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 256.450527] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 256.457770] PKRU: 55555554 [ 256.460529] Call Trace: [ 256.463015] <TASK> [ 256.465157] ? ice_xmit_zc+0x6e/0x150 [ice] [ 256.469437] ice_napi_poll+0x46d/0x680 [ice] [ 256.473815] ? _raw_spin_unlock_irqrestore+0x1b/0x40 [ 256.478863] __napi_poll+0x29/0x160 [ 256.482409] net_rx_action+0x136/0x260 [ 256.486222] __do_softirq+0xe8/0x2e5 [ 256.489853] ? smpboot_thread_fn+0x2c/0x270 [ 256.494108] run_ksoftirqd+0x2a/0x50 [ 256.497747] smpboot_thread_fn+0x1c1/0x270 [ 256.501907] ? __pfx_smpboot_thread_fn+0x10/0x10 [ 256.506594] kthread+0xea/0x120 [ 256.509785] ? __pfx_kthread+0x10/0x10 [ 256.513597] ret_from_fork+0x29/0x50 [ 256.517238] </TASK> In fact, irqs were not disabled and napi managed to be scheduled and run while xsk_pool pointer was still valid, but SW ring of xdp_buff pointers was already freed. To fix this, call ice_qvec_dis_irq() after ice_vsi_stop_tx_ring(). Also while at it, remove redundant ice_clean_rx_ring() call - this is handled in ice_qp_clean_rings(). Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-16igc: fix the validation logic for taprio's gate listAKASHI Takahiro
The check introduced in the commit a5fd39464a40 ("igc: Lift TAPRIO schedule restriction") can detect a false positive error in some corner case. For instance, tc qdisc replace ... taprio num_tc 4 ... sched-entry S 0x01 100000 # slot#1 sched-entry S 0x03 100000 # slot#2 sched-entry S 0x04 100000 # slot#3 sched-entry S 0x08 200000 # slot#4 flags 0x02 # hardware offload Here the queue#0 (the first queue) is on at the slot#1 and #2, and off at the slot#3 and #4. Under the current logic, when the slot#4 is examined, validate_schedule() returns *false* since the enablement count for the queue#0 is two and it is already off at the previous slot (i.e. #3). But this definition is truely correct. Let's fix the logic to enforce a strict validation for consecutively-opened slots. Fixes: a5fd39464a40 ("igc: Lift TAPRIO schedule restriction") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-03-16igbvf: Regard vf reset nack as successAkihiko Odaki
vf reset nack actually represents the reset operation itself is performed but no address is assigned. Therefore, e1000_reset_hw_vf should fill the "perm_addr" with the zero address and return success on such an occasion. This prevents its callers in netdev.c from saying PF still resetting, and instead allows them to correctly report that no address is assigned. Fixes: 6ddbc4cf1f4d ("igb: Indicate failure on vf reset for empty mac address") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-03-16intel/igbvf: free irq on the error path in igbvf_request_msix()Gaosheng Cui
In igbvf_request_msix(), irqs have not been freed on the err path, we need to free it. Fix it. Fixes: d4e0fe01a38a ("igbvf: add new driver to support 82576 virtual functions") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-03-16igb: Enable SR-IOV after reinitAkihiko Odaki
Enabling SR-IOV causes the virtual functions to make requests to the PF via the mailbox. Notably, E1000_VF_RESET request will happen during the initialization of the VF. However, unless the reinit is done, the VMMB interrupt, which delivers mailbox interrupt from VF to PF will be kept masked and such requests will be silently ignored. Enable SR-IOV at the very end of the procedure to configure the device for SR-IOV so that the PF is configured properly for SR-IOV when a VF is activated. Fixes: fa44f2f185f7 ("igb: Enable SR-IOV configuration via PCI sysfs interface") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-03-16igb: revert rtnl_lock() that causes deadlockLin Ma
The commit 6faee3d4ee8b ("igb: Add lock to avoid data race") adds rtnl_lock to eliminate a false data race shown below (FREE from device detaching) | (USE from netdev core) igb_remove | igb_ndo_get_vf_config igb_disable_sriov | vf >= adapter->vfs_allocated_count? kfree(adapter->vf_data) | adapter->vfs_allocated_count = 0 | | memcpy(... adapter->vf_data[vf] The above race will never happen and the extra rtnl_lock causes deadlock below [ 141.420169] <TASK> [ 141.420672] __schedule+0x2dd/0x840 [ 141.421427] schedule+0x50/0xc0 [ 141.422041] schedule_preempt_disabled+0x11/0x20 [ 141.422678] __mutex_lock.isra.13+0x431/0x6b0 [ 141.423324] unregister_netdev+0xe/0x20 [ 141.423578] igbvf_remove+0x45/0xe0 [igbvf] [ 141.423791] pci_device_remove+0x36/0xb0 [ 141.423990] device_release_driver_internal+0xc1/0x160 [ 141.424270] pci_stop_bus_device+0x6d/0x90 [ 141.424507] pci_stop_and_remove_bus_device+0xe/0x20 [ 141.424789] pci_iov_remove_virtfn+0xba/0x120 [ 141.425452] sriov_disable+0x2f/0xf0 [ 141.425679] igb_disable_sriov+0x4e/0x100 [igb] [ 141.426353] igb_remove+0xa0/0x130 [igb] [ 141.426599] pci_device_remove+0x36/0xb0 [ 141.426796] device_release_driver_internal+0xc1/0x160 [ 141.427060] driver_detach+0x44/0x90 [ 141.427253] bus_remove_driver+0x55/0xe0 [ 141.427477] pci_unregister_driver+0x2a/0xa0 [ 141.428296] __x64_sys_delete_module+0x141/0x2b0 [ 141.429126] ? mntput_no_expire+0x4a/0x240 [ 141.429363] ? syscall_trace_enter.isra.19+0x126/0x1a0 [ 141.429653] do_syscall_64+0x5b/0x80 [ 141.429847] ? exit_to_user_mode_prepare+0x14d/0x1c0 [ 141.430109] ? syscall_exit_to_user_mode+0x12/0x30 [ 141.430849] ? do_syscall_64+0x67/0x80 [ 141.431083] ? syscall_exit_to_user_mode_prepare+0x183/0x1b0 [ 141.431770] ? syscall_exit_to_user_mode+0x12/0x30 [ 141.432482] ? do_syscall_64+0x67/0x80 [ 141.432714] ? exc_page_fault+0x64/0x140 [ 141.432911] entry_SYSCALL_64_after_hwframe+0x72/0xdc Since the igb_disable_sriov() will call pci_disable_sriov() before releasing any resources, the netdev core will synchronize the cleanup to avoid any races. This patch removes the useless rtnl_(un)lock to guarantee correctness. CC: stable@vger.kernel.org Fixes: 6faee3d4ee8b ("igb: Add lock to avoid data race") Reported-by: Corinna Vinschen <vinschen@redhat.com> Link: https://lore.kernel.org/intel-wired-lan/ZAcJvkEPqWeJHO2r@calimero.vinschen.de/ Signed-off-by: Lin Ma <linma@zju.edu.cn> Tested-by: Corinna Vinschen <vinschen@redhat.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-03-16iavf: do not track VLAN 0 filtersAhmed Zaki
When an interface with the maximum number of VLAN filters is brought up, a spurious error is logged: [257.483082] 8021q: adding VLAN 0 to HW filter on device enp0s3 [257.483094] iavf 0000:00:03.0 enp0s3: Max allowed VLAN filters 8. Remove existing VLANs or disable filtering via Ethtool if supported. The VF driver complains that it cannot add the VLAN 0 filter. On the other hand, the PF driver always adds VLAN 0 filter on VF initialization. The VF does not need to ask the PF for that filter at all. Fix the error by not tracking VLAN 0 filters altogether. With that, the check added by commit 0e710a3ffd0c ("iavf: Fix VF driver counting VLAN 0 filters") in iavf_virtchnl.c is useless and might be confusing if left as it suggests that we track VLAN 0. Fixes: 0e710a3ffd0c ("iavf: Fix VF driver counting VLAN 0 filters") Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-03-16iavf: fix non-tunneled IPv6 UDP packet type and hashingAlexander Lobakin
Currently, IAVF's decode_rx_desc_ptype() correctly reports payload type of L4 for IPv4 UDP packets and IPv{4,6} TCP, but only L3 for IPv6 UDP. Originally, i40e, ice and iavf were affected. Commit 73df8c9e3e3d ("i40e: Correct UDP packet header for non_tunnel-ipv6") fixed that in i40e, then commit 638a0c8c8861 ("ice: fix incorrect payload indicator on PTYPE") fixed that for ice. IPv6 UDP is L4 obviously. Fix it and make iavf report correct L4 hash type for such packets, so that the stack won't calculate it on CPU when needs it. Fixes: 206812b5fccb ("i40e/i40evf: i40e implementation for skb_set_hash") Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-03-16iavf: fix inverted Rx hash condition leading to disabled hashAlexander Lobakin
Condition, which checks whether the netdev has hashing enabled is inverted. Basically, the tagged commit effectively disabled passing flow hash from descriptor to skb, unless user *disables* it via Ethtool. Commit a876c3ba59a6 ("i40e/i40evf: properly report Rx packet hash") fixed this problem, but only for i40e. Invert the condition now in iavf and unblock passing hash to skbs again. Fixes: 857942fd1aa1 ("i40e: Fix Rx hash reported to the stack by our driver") Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-03-16fbdev: Use of_property_present() for testing DT property presenceRob Herring
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. As part of this, convert of_get_property/of_find_property calls to the recently added of_property_present() helper when we just want to test for presence of a property and nothing more. Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Helge Deller <deller@gmx.de>
2023-03-16fbdev: au1200fb: Fix potential divide by zeroWei Chen
var->pixclock can be assigned to zero by user. Without proper check, divide by zero would occur when invoking macro PICOS2KHZ in au1200fb_fb_check_var. Error out if var->pixclock is zero. Signed-off-by: Wei Chen <harperchen1110@gmail.com> Signed-off-by: Helge Deller <deller@gmx.de>
2023-03-16fbdev: lxfb: Fix potential divide by zeroWei Chen
var->pixclock can be assigned to zero by user. Without proper check, divide by zero would occur in lx_set_clock. Error out if var->pixclock is zero. Signed-off-by: Wei Chen <harperchen1110@gmail.com> Signed-off-by: Helge Deller <deller@gmx.de>
2023-03-16fbdev: intelfb: Fix potential divide by zeroWei Chen
Variable var->pixclock is controlled by user and can be assigned to zero. Without proper check, divide by zero would occur in intelfbhw_validate_mode and intelfbhw_mode_to_hw. Error out if var->pixclock is zero. Signed-off-by: Wei Chen <harperchen1110@gmail.com> Signed-off-by: Helge Deller <deller@gmx.de>
2023-03-16fbdev: nvidia: Fix potential divide by zeroWei Chen
variable var->pixclock can be set by user. In case it equals to zero, divide by zero would occur in nvidiafb_set_par. Similar crashes have happened in other fbdev drivers. There is no check and modification on var->pixclock along the call chain to nvidia_check_var and nvidiafb_set_par. We believe it could also be triggered in driver nvidia from user site. Signed-off-by: Wei Chen <harperchen1110@gmail.com> Signed-off-by: Helge Deller <deller@gmx.de>
generated by cgit (git 2.34.1) at 2025-09-12 23:35:52 +0000