| Age | Commit message (Collapse) | Author |
|---|
|
There are situations during the xhci_resume() sequence, which allows for
re-initializing of the XHCI HC. However, in case the HCD is being removed,
these operations may not be needed. Set the removal state before issuing
the runtime PM get on the XHCI device, so that the XHCI resume routine will
know when to bypass the re-init logic.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Message-ID: <20230531222719.14143-3-quic_wcheng@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During XHCI resume, if there was a host controller error detected the
routine will attempt to re-initialize the XHCI HC, so that it can return
back to an operational state. If the XHCI host controller is being
removed, this sequence would be already handled within the XHCI halt path,
leading to a duplicate set of reg ops/calls. In addition, since the XHCI
bus is being removed, the overhead added in restarting the HCD is
unnecessary. Check for the XHC state before setting the reinit_xhc
parameter, which is responsible for triggering the restart.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Message-ID: <20230531222719.14143-2-quic_wcheng@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the following config set:
CONFIG_DRM=m
CONFIG_DRM_PANEL=y
CONFIG_DRM_BRIDGE=y
CONFIG_DRM_PANEL_BRIDGE=y
CONFIG_TYPEC_MUX_NB7VPQ904M=y
vmlinux fails on the following symbols:
ld.lld: error: undefined symbol: devm_drm_bridge_add
ld.lld: error: undefined symbol: devm_drm_of_get_bridge
Add dependendy on DRM || DRM=no since CONFIG_DRM dependency is optional
and guarded by:
IS_ENABLED(CONFIG_OF) && IS_ENABLED(CONFIG_DRM_PANEL_BRIDGE)
in the drive.
Also add "select DRM_PANEL_BRIDGE if DRM" to clarify DRM_PANEL_BRIDGE
is required if CONFIG_DRM is enabled.
Fixes: 88d8f3ac9c67 ("usb: typec: add support for the nb7vpq904m Type-C Linear Redriver")
Reported-by: Arnd Bergmann <arnd@kernel.org>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Message-ID: <20230622-topic-sm8x50-upstream-redriver-config-fix-v1-1-005ab6f4d1f5@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with strscpy().
Direct replacement is safe here since return value of -errno
is used to check for truncation instead of sizeof(dest).
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Message-ID: <20230615180504.401169-1-azeemshaikh38@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In scenarios where pullup relies on resume (get sync) to initialize
the controller and set the run stop bit, then core_init is followed by
gadget_resume which will eventually set run stop bit.
But in cases where the core_init fails, the return value is not sent
back to udc appropriately. So according to UDC the controller has
started but in reality we never set the run stop bit.
On systems like Android, there are uevents sent to HAL depending on
whether the configfs_bind / configfs_disconnect were invoked. In the
above mentioned scnenario, if the core init fails, the run stop won't
be set and the cable plug-out won't result in generation of any
disconnect event and userspace would never get any uevent regarding
cable plug out and we never call pullup(0) again. Furthermore none of
the next Plug-In/Plug-Out's would be known to configfs.
Return back the appropriate result to UDC to let the userspace/
configfs know that the pullup failed so they can take appropriate
action.
Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <20230618120949.14868-1-quic_kriskura@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.5-rc1
Here are the USB-serial updates for 6.5-rc1, including:
- improved error handling for break signalling
- report to user space when a device does not support break signalling
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.5-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add LARA-R6 01B PIDs
USB: serial: report unsupported break signalling
USB: serial: cp210x: disable break signalling on CP2105 SCI
USB: serial: return errors from break handling
|
|
Smatch reports:
drivers/clocksource/timer-cadence-ttc.c:529 ttc_timer_probe()
warn: 'timer_baseaddr' from of_iomap() not released on lines: 498,508,516.
timer_baseaddr may have the problem of not being released after use,
I replaced it with the devm_of_iomap() function and added the clk_put()
function to cleanup the "clk_ce" and "clk_cs".
Fixes: e932900a3279 ("arm: zynq: Use standard timer binding")
Fixes: 70504f311d4b ("clocksource/drivers/cadence_ttc: Convert init function to return error")
Signed-off-by: Feng Mingxi <m202271825@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230425065611.702917-1-m202271825@hust.edu.cn
|
|
Current code assigns either the Hyper-V TSC page or MSR-based ref counter
as the sched clock. This may be sub-optimal in two cases. First, if there
is hardware support to ensure consistent TSC frequency across live
migrations and Hyper-V is using that support, the raw TSC is a faster
source of time than the Hyper-V TSC page. Second, the MSR-based ref
counter is relatively slow because reads require a trap to the hypervisor.
As such, it should never be used as the sched clock. The native sched
clock based on the raw TSC or jiffies is much better.
Rework the sched clock setup so it is set to the TSC page only if
Hyper-V indicates that the TSC may have inconsistent frequency across
live migrations. Also, remove the code that sets the sched clock to
the MSR-based ref counter. In the cases where it is not set, the sched
clock will then be the native sched clock.
As part of the rework, always enable both the TSC page clocksource and
the MSR-based ref counter clocksource. Set the ratings so the TSC page
clocksource is preferred. While the MSR-based ref counter clocksource
is unlikely to ever be the default, having it available for manual
selection is convenient for development purposes.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1687201360-16003-1-git-send-email-mikelley@microsoft.com
|
|
Only the imx-gpt timer driver makes use of enum imx_gpt_type that is
otherwise unused. Move its definition into the timer-imx-gpt driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230328100531.879485-3-u.kleine-koenig@pengutronix.de
|
|
The clk drivers use none of the symbols defined in <soc/imx/timer.h>.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230328100531.879485-2-u.kleine-koenig@pengutronix.de
|
|
memory_group_register_static takes maximum number of pages as the argument
while dev_dax_kmem_probe passes total_len (in bytes) as the argument.
IIUC, I don't see any crash/panic impact as such. As,
memory_group_register_static just set the max_pages limit which is used in
auto_movable_zone_for_pfn to determine the zone.
which might cause these condition to behave differently,
This will be true always so jump will happen to kernel_zone
...
if (!auto_movable_can_online_movable(NUMA_NO_NODE, group, nr_pages))
goto kernel_zone;
...
kernel_zone:
return default_kernel_zone_for_pfn(nid, pfn, nr_pages);
Here, In below, zone_intersects compare range will be larger as nr_pages
will be higher (derived from total_len passed in dev_dax_kmem_probe).
...
static struct zone *default_kernel_zone_for_pfn(int nid, unsigned long start_pfn,
unsigned long nr_pages)
{
struct pglist_data *pgdat = NODE_DATA(nid);
int zid;
for (zid = 0; zid < ZONE_NORMAL; zid++) {
struct zone *zone = &pgdat->node_zones[zid];
if (zone_intersects(zone, start_pfn, nr_pages))
return zone;
}
return &pgdat->node_zones[ZONE_NORMAL];
}
Incorrect zone will be returned here, which in later time might cause bigger
problem.
Fixes: eedf634aac3b ("dax/kmem: use a single static memory group for a single probed unit")
Signed-off-by: Tarun Sahu <tsahu@linux.ibm.com>
Link: https://lore.kernel.org/r/20230621155025.370672-1-tsahu@linux.ibm.com
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
Now that free_dev_dax_id() internally manages the references it needs
the extra references taken by the dax_region drivers are not needed.
Reported-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/168577285161.1672036.8111253437794419696.stgit@dwillia2-xfh.jf.intel.com
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
The reference counting of dax_region objects is needlessly complicated,
has lead to confusion [1], and has hidden a bug [2]. Towards cleaning up
that mess introduce alloc_dev_dax_id() to minimize the holding of a
dax_region reference to only what dev_dax_release() needs, the
dax_region->ida.
Part of the reason for the mess was the design to dereference a
dax_region in all cases in free_dev_dax_id() even if the id was
statically assigned by the upper level dax_region driver. Remove the
need to call "is_static(dax_region)" by tracking whether the id is
dynamic directly in the dev_dax instance itself.
With that flag the dax_region pinning and release per dev_dax instance
can move to alloc_dev_dax_id() and free_dev_dax_id() respectively.
A follow-on cleanup address the unnecessary references in the dax_region
setup and drivers.
Fixes: 0f3da14a4f05 ("device-dax: introduce 'seed' devices")
Link: http://lore.kernel.org/r/20221203095858.612027-1-liuyongqiang13@huawei.com [1]
Link: http://lore.kernel.org/r/3cf0890b-4eb0-e70e-cd9c-2ecc3d496263@hpe.com [2]
Reported-by: Yongqiang Liu <liuyongqiang13@huawei.com>
Reported-by: Paul Cassella <cassella@hpe.com>
Reported-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/168577284563.1672036.13493034988900989554.stgit@dwillia2-xfh.jf.intel.com
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
Replace an open-coded device_unregister() sequence with the helper.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/168577283989.1672036.7777592498865470652.stgit@dwillia2-xfh.jf.intel.com
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
A CONFIG_DEBUG_KOBJECT_RELEASE test of removing a device-dax region
provider (like modprobe -r dax_hmem) yields:
kobject: 'mapping0' (ffff93eb460e8800): kobject_release, parent 0000000000000000 (delayed 2000)
[..]
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 23 PID: 282 at kernel/locking/lockdep.c:232 __lock_acquire+0x9fc/0x2260
[..]
RIP: 0010:__lock_acquire+0x9fc/0x2260
[..]
Call Trace:
<TASK>
[..]
lock_acquire+0xd4/0x2c0
? ida_free+0x62/0x130
_raw_spin_lock_irqsave+0x47/0x70
? ida_free+0x62/0x130
ida_free+0x62/0x130
dax_mapping_release+0x1f/0x30
device_release+0x36/0x90
kobject_delayed_cleanup+0x46/0x150
Due to attempting ida_free() on an ida object that has already been
freed. Devices typically only hold a reference on their parent while
registered. If a child needs a parent object to complete its release it
needs to hold a reference that it drops from its release callback.
Arrange for a dax_mapping to pin its parent dev_dax instance until
dax_mapping_release().
Fixes: 0b07ce872a9e ("device-dax: introduce 'mapping' devices")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/168577283412.1672036.16111545266174261446.stgit@dwillia2-xfh.jf.intel.com
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Notable changes this time around:
MAINTAINERS
- add missing driver git trees
ath11k
- factory test mode support
iwlwifi
- config rework to drop test devices and
split the different families
- major update for new firmware and MLO
stack
- initial multi-link reconfiguration suppor
- multi-BSSID and MLO improvements
other
- fix the last few W=1 warnings from GCC 13
- merged wireless tree to avoid conflicts
* tag 'wireless-next-2023-06-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (245 commits)
wifi: ieee80211: fix erroneous NSTR bitmap size checks
wifi: rtlwifi: cleanup USB interface
wifi: rtlwifi: simplify LED management
wifi: ath10k: improve structure padding
wifi: ath9k: convert msecs to jiffies where needed
wifi: iwlwifi: mvm: Add support for IGTK in D3 resume flow
wifi: iwlwifi: mvm: update two most recent GTKs on D3 resume flow
wifi: iwlwifi: mvm: Refactor security key update after D3
wifi: mac80211: mark keys as uploaded when added by the driver
wifi: iwlwifi: remove support of A0 version of FM RF
wifi: iwlwifi: cfg: clean up Bz module firmware lines
wifi: iwlwifi: pcie: add device id 51F1 for killer 1675
wifi: iwlwifi: bump FW API to 83 for AX/BZ/SC devices
wifi: iwlwifi: cfg: remove trailing dash from FW_PRE constants
wifi: iwlwifi: also unify Ma device configurations
wifi: iwlwifi: also unify Sc device configurations
wifi: iwlwifi: unify Bz/Gl device configurations
wifi: iwlwifi: pcie: also drop jacket from info macro
wifi: iwlwifi: remove support for *nJ devices
wifi: iwlwifi: don't load old firmware for 22000
...
====================
Link: https://lore.kernel.org/r/20230622185602.147650-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-06-22
The first patch is by Carsten Schmidt, targets the kvaser_usb driver
and adds len8_dlc support.
Marcel Hellwig's patch for the xilinx_can driver adds support for CAN
transceivers via the PHY framework.
Frank Jungclaus contributes 6+2 patches for the esd_usb driver in
preparation for the upcoming CAN-USB/3 support.
The 2 patches by Miquel Raynal for the sja1000 driver work around
overruns stalls on the Renesas SoCs.
The next 3 patches are by me and fix the coding style in the
rx-offload helper and in the m_can and ti_hecc driver.
Vincent Mailhol contributes 3 patches to fix and update the
calculation of the length of CAN frames on the wire.
Oliver Hartkopp's patch moves the CAN_RAW_FILTER_MAX definition into
the correct header.
The remaining 14 patches are by Jimmy Assarsson, target the
kvaser_pciefd driver and bring various updates and improvements.
* tag 'linux-can-next-for-6.5-20230622' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (33 commits)
can: kvaser_pciefd: Use TX FIFO size read from CAN controller
can: kvaser_pciefd: Refactor code
can: kvaser_pciefd: Add len8_dlc support
can: kvaser_pciefd: Use FIELD_{GET,PREP} and GENMASK where appropriate
can: kvaser_pciefd: Sort register definitions
can: kvaser_pciefd: Change return type for kvaser_pciefd_{receive,transmit,set_tx}_irq()
can: kvaser_pciefd: Rename device ID defines
can: kvaser_pciefd: Sort includes in alphabetic order
can: kvaser_pciefd: Remove SPI flash parameter read functionality
can: uapi: move CAN_RAW_FILTER_MAX definition to raw.h
can: kvaser_pciefd: Define unsigned constants with type suffix 'U'
can: kvaser_pciefd: Set hardware timestamp on transmitted packets
can: kvaser_pciefd: Add function to set skb hwtstamps
can: kvaser_pciefd: Remove handler for unused KVASER_PCIEFD_PACK_TYPE_EFRAME_ACK
can: kvaser_pciefd: Remove useless write to interrupt register
can: length: refactor frame lengths definition to add size in bits
can: length: fix bitstuffing count
can: length: fix description of the RRS field
can: m_can: fix coding style
can: ti_hecc: fix coding style
...
====================
Link: https://lore.kernel.org/r/20230622082658.571150-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When processing counter updates, if any action set using the newly
incremented counter includes an encap action, prod the corresponding
neighbouring entry to indicate to the neighbour cache that the entry
is still in use and passing traffic.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230621121504.17004-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The QCA8K switch supports additional modes that can be handled in
hardware for the LED netdev trigger.
Add these additional modes to further support the Switch LEDs and
offload more blink modes.
Add additional modes:
- link_10
- link_100
- link_1000
- half_duplex
- full_duplex
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230621095409.25859-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a setup where a Thunderbolt hub connects to Ethernet and a display
through USB Type-C, users may experience a hung task timeout when they
remove the cable between the PC and the Thunderbolt hub.
This is because the igb_down function is called multiple times when
the Thunderbolt hub is unplugged. For example, the igb_io_error_detected
triggers the first call, and the igb_remove triggers the second call.
The second call to igb_down will block at napi_synchronize.
Here's the call trace:
__schedule+0x3b0/0xddb
? __mod_timer+0x164/0x5d3
schedule+0x44/0xa8
schedule_timeout+0xb2/0x2a4
? run_local_timers+0x4e/0x4e
msleep+0x31/0x38
igb_down+0x12c/0x22a [igb 6615058754948bfde0bf01429257eb59f13030d4]
__igb_close+0x6f/0x9c [igb 6615058754948bfde0bf01429257eb59f13030d4]
igb_close+0x23/0x2b [igb 6615058754948bfde0bf01429257eb59f13030d4]
__dev_close_many+0x95/0xec
dev_close_many+0x6e/0x103
unregister_netdevice_many+0x105/0x5b1
unregister_netdevice_queue+0xc2/0x10d
unregister_netdev+0x1c/0x23
igb_remove+0xa7/0x11c [igb 6615058754948bfde0bf01429257eb59f13030d4]
pci_device_remove+0x3f/0x9c
device_release_driver_internal+0xfe/0x1b4
pci_stop_bus_device+0x5b/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_and_remove_bus_device+0x12/0x19
pciehp_unconfigure_device+0x76/0xe9
pciehp_disable_slot+0x6e/0x131
pciehp_handle_presence_or_link_change+0x7a/0x3f7
pciehp_ist+0xbe/0x194
irq_thread_fn+0x22/0x4d
? irq_thread+0x1fd/0x1fd
irq_thread+0x17b/0x1fd
? irq_forced_thread_fn+0x5f/0x5f
kthread+0x142/0x153
? __irq_get_irqchip_state+0x46/0x46
? kthread_associate_blkcg+0x71/0x71
ret_from_fork+0x1f/0x30
In this case, igb_io_error_detected detaches the network interface
and requests a PCIE slot reset, however, the PCIE reset callback is
not being invoked and thus the Ethernet connection breaks down.
As the PCIE error in this case is a non-fatal one, requesting a
slot reset can be avoided.
This patch fixes the task hung issue and preserves Ethernet
connection by ignoring non-fatal PCIE errors.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230620174732.4145155-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the errata sheets for ksz9477 and ksz9567, writes to the
PHY registers 0x10-0x1f (i.e. those located at addresses 0xN120 to
0xN13f) must be done as a 32 bit write to the 4-byte aligned address
containing the register, hence requires a RMW in order not to change
the adjacent PHY register.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230620113855.733526-4-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This will be used in a subsequent patch fixing an errata for writes to
certain PHY registers.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20230620113855.733526-3-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement ksz_prmw8() in terms of ksz_rmw8(), just as all the other
ksz_pX are implemented in terms of ksz_X. No functional change.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20230620113855.733526-2-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Half a year passed since commit 049fe5365324c ("net: txgbe: Add operations
to interact with firmware") was submitted, the buffer in
txgbe_calc_eeprom_checksum was not used. So remove it and the related
branch codes.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306200242.FXsHokaJ-lkp@intel.com/
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230620062519.1575298-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix an issue where the kernel would stall during netboot, showing the
"sched: RT throttling activated" message. This stall was triggered by
the behavior of the mii_interrupt bit (Bit 7 - DP83TD510E_STS_MII_INT)
in the DP83TD510E's PHY_STS Register (Address = 0x10). The DP83TD510E
datasheet (2020) states that the bit clears on write, however, in
practice, the bit clears on read.
This discrepancy had significant implications on the driver's interrupt
handling. The PHY_STS Register was used by handle_interrupt() to check
for pending interrupts and by read_status() to get the current link
status. The call to read_status() was unintentionally clearing the
mii_interrupt status bit without deasserting the IRQ pin, causing
handle_interrupt() to miss other pending interrupts. This issue was most
apparent during netboot.
The fix refrains from using the PHY_STS Register for interrupt handling.
Instead, we now solely rely on the INTERRUPT_REG_1 Register (Address =
0x12) and INTERRUPT_REG_2 Register (Address = 0x13) for this purpose.
These registers directly influence the IRQ pin state and are latched
high until read.
Note: The INTERRUPT_REG_2 Register (Address = 0x13) exists and can also
be used for interrupt handling, specifically for "Aneg page received
interrupt" and "Polarity change interrupt". However, these features are
currently not supported by this driver.
Fixes: 165cd04fe253 ("net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY")
Cc: <stable@vger.kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230621043848.3806124-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update macb's embedded PCS drivers to use neg_mode, even though it
makes no use of it or the "mode" argument. This makes the driver
consistent with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Eo-00EaGX-KJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update mt7530's embedded PCS driver to use neg_mode, even though it
makes no use of it or the "mode" argument. This makes the driver
consistent with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Ej-00EaGR-Fk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update B53's embedded PCS driver to use neg_mode, even though it makes
no use of it or the "mode" argument. This makes the driver consistent
with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1qA8Ee-00EaGL-Az@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update Sparx5's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EZ-00EaGF-6F@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update qca8k's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EU-00EaG9-1l@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update prestera's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Acked-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EO-00EaG3-TR@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update mvpp2's embedded PCS drivers to use neg_mode rather than the
mode argument, remembering to update the ACPI path as well. As there
are no pcs_link_up() methods, this only affects the two pcs_config()
methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EJ-00EaFx-P6@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update mvneta's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EE-00EaFr-Kx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update lan966x's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8E9-00EaFl-GN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the Lynx PCS driver to use neg_mode rather than the mode
argument. This ensures that the link_up() method will always program
the speed and duplex when negotiation is disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8E4-00EaFf-Bf@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the Lynxi PCS driver to use neg_mode rather than the mode
argument. This ensures that the link_up() method will always program
the speed and duplex when negotiation is disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dz-00EaFY-5A@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update xpcs to use neg_mode to configure whether inband negotiation
should be used. We need to update sja1105 as well as that directly
calls into the XPCS driver's config function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dt-00EaFS-W9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert fman_dtsec, xilinx_axienet and pcs-lynx to pass the neg_mode
into phylink_mii_c22_pcs_config(). Where appropriate, drivers are
updated to have neg_mode passed into their pcs_config() and
pcs_link_up() functions. For other drivers, we just hoist the call
to phylink_pcs_neg_mode() to their pcs_config() method out of
phylink_mii_c22_pcs_config().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Do-00EaFM-Ra@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use phylink_pcs_neg_mode() for phylink_mii_c22_pcs_config(). This
results in no functional change.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dj-00EaFG-Mt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PCS have to work out whether they should enable PCS negotiation by
looking at the "mode" and "interface" arguments, and the Autoneg bit
in the advertising mask.
This leads to some complex logic, so lets pull that out into phylink
and instead pass a "neg_mode" argument to the PCS configuration and
link up methods, instead of the "mode" argument.
In order to transition drivers, add a "neg_mode" flag to the phylink
PCS structure to PCS can indicate whether they want to be passed the
neg_mode or the old mode argument.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8De-00EaFA-Ht@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Spell "transmission" properly.
Found by searching for keyword "tranm".
Signed-off-by: Yueh-Shun Li <shamrocklee@posteo.net>
Link: https://lore.kernel.org/r/20230622012627.15050-3-shamrocklee@posteo.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 49725ffc15fc ("net: stmmac: power up/down serdes in
stmmac_open/release") correctly added a call to the serdes_powerdown()
callback to stmmac_release() but did not remove the one from
stmmac_remove() which leads to a doubled call to serdes_powerdown().
This can lead to all kinds of problems: in the case of the qcom ethqos
driver, it caused an unbalanced regulator disable splat.
Fixes: 49725ffc15fc ("net: stmmac: power up/down serdes in stmmac_open/release")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230621135537.376649-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
tools/testing/selftests/net/fcnal-test.sh
d7a2fc1437f7 ("selftests: net: fcnal-test: check if FIPS mode is enabled")
dd017c72dde6 ("selftests: fcnal: Test SO_DONTROUTE on TCP sockets.")
https://lore.kernel.org/all/5007b52c-dd16-dbf6-8d64-b9701bfa498b@tessares.net/
https://lore.kernel.org/all/20230619105427.4a0df9b3@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from ipsec, bpf, mptcp and netfilter.
Current release - regressions:
- netfilter: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain
- eth: mlx5e:
- fix scheduling of IPsec ASO query while in atomic
- free IRQ rmap and notifier on kernel shutdown
Current release - new code bugs:
- phy: manual remove LEDs to ensure correct ordering
Previous releases - regressions:
- mptcp: fix possible divide by zero in recvmsg()
- dsa: revert "net: phy: dp83867: perform soft reset and retain
established link"
Previous releases - always broken:
- sched: netem: acquire qdisc lock in netem_change()
- bpf:
- fix verifier id tracking of scalars on spill
- fix NULL dereference on exceptions
- accept function names that contain dots
- netfilter: disallow element updates of bound anonymous sets
- mptcp: ensure listener is unhashed before updating the sk status
- xfrm:
- add missed call to delete offloaded policies
- fix inbound ipv4/udp/esp packets to UDPv6 dualstack sockets
- selftests: fixes for FIPS mode
- dsa: mt7530: fix multiple CPU ports, BPDU and LLDP handling
- eth: sfc: use budget for TX completions
Misc:
- wifi: iwlwifi: add support for SO-F device with PCI id 0x7AF0"
* tag 'net-6.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits)
revert "net: align SO_RCVMARK required privileges with SO_MARK"
net: wwan: iosm: Convert single instance struct member to flexible array
sch_netem: acquire qdisc lock in netem_change()
selftests: forwarding: Fix race condition in mirror installation
wifi: mac80211: report all unusable beacon frames
mptcp: ensure listener is unhashed before updating the sk status
mptcp: drop legacy code around RX EOF
mptcp: consolidate fallback and non fallback state machine
mptcp: fix possible list corruption on passive MPJ
mptcp: fix possible divide by zero in recvmsg()
mptcp: handle correctly disconnect() failures
bpf: Force kprobe multi expected_attach_type for kprobe_multi link
bpf/btf: Accept function names that contain dots
Revert "net: phy: dp83867: perform soft reset and retain established link"
net: mdio: fix the wrong parameters
netfilter: nf_tables: Fix for deleting base chains with payload
netfilter: nfnetlink_osf: fix module autoload
netfilter: nf_tables: drop module reference after updating chain
netfilter: nf_tables: disallow timeout for anonymous sets
netfilter: nf_tables: disallow updates of anonymous sets
...
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why
Generic:
- Avoid setting page table entries pointing to a deleted memslot if a
host page table entry is changed concurrently with the deletion"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Avoid illegal stage2 mapping on invalid memory slot
KVM: arm64: Use raw_smp_processor_id() in kvm_pmu_probe_armpmu()
KVM: arm64: Restore GICv2-on-GICv3 functionality
KVM: arm64: PMU: Don't overwrite PMUSERENR with vcpu loaded
KVM: arm64: PMU: Restore the host's PMUSERENR_EL0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Fix support for deferred probing for several host drivers
- litex_mmc: Use async probe as it's common for all mmc hosts
- meson-gx: Fix bug when scheduling while atomic
- mmci_stm32: Fix max busy timeout calculation
- sdhci-msm: Disable broken 64-bit DMA on MSM8916
* tag 'mmc-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: usdhi60rol0: fix deferred probing
mmc: sunxi: fix deferred probing
mmc: sh_mmcif: fix deferred probing
mmc: sdhci-spear: fix deferred probing
mmc: sdhci-acpi: fix deferred probing
mmc: owl: fix deferred probing
mmc: omap_hsmmc: fix deferred probing
mmc: omap: fix deferred probing
mmc: mvsdio: fix deferred probing
mmc: mtk-sd: fix deferred probing
mmc: meson-gx: fix deferred probing
mmc: bcm2835: fix deferred probing
mmc: litex_mmc: set PROBE_PREFER_ASYNCHRONOUS
mmc: meson-gx: remove redundant mmc_request_done() call from irq context
mmc: mmci: stm32: fix max busy timeout calculation
mmc: sdhci-msm: Disable broken 64-bit DMA on MSM8916
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fix from Hans de Goede:
"One small fix for an AMD PMF driver issue which is causing issues for
users of just released AMD laptop models"
* tag 'platform-drivers-x86-v6.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86/amd/pmf: Register notify handler only if SPS is enabled
|
|
asm/octeon/octeon.h already includes asm/bitfield.h, so there is no need
to include this latter file in ahci_octeon.c as the code does not
directly use the __BITFIELD_FIELD macro defined in it.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Merge series from Miquel Raynal <miquel.raynal@bootlin.com>:
I recently came across an issue with the Atmel spi controller driver
which would stop my transfers after a too small timeout when performing
big transfers (reading a 4MiB flash in one transfer). My initial idea
was to derive a the maximum amount of time a transfer would take
depending on its size and use that as value to avoid erroring-out when
not relevant. Mark wanted to go further by creating a core helper doing
that, based on the heuristics from the sun6i driver.
Here is a small series of 3 patches doing exactly that.
|
|
The kernel already has a helper to print a hexdump of a small
buffer via pointer extension. Use that instead of open coded
variant.
In long term it helps to kill pr_cont() or at least narrow down
its use.
Note, the format is slightly changed, i.e. the trailing space is
always printed. Also the IV dump is limited by 64 bytes which seems
fine.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
