| Age | Commit message (Collapse) | Author |
|---|
|
Before sending a SESSION PROTECTION cmd the driver checks if
the link_id indicated in the time event (and for which the cmd will be
sent) is valid and exists.
Clear the te_data::link_id when FW notifies that a session protection
ended, so the check will actually fail when it should.
Fixes: 135065837310 ("wifi: iwlwifi: support link_id in SESSION_PROTECTION cmd")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240204235836.c64a6b3606c2.I35cdc08e8a3be282563163690f8ca3edb51a3854@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As described in IEEE sta 802.11-2020, table 9-30 (Address
field contents), A-MSDU address 3 should contain the BSSID
address.
In TX_CMD we copy the MAC header from skb, and skb address 3
holds the destination address, but it may not be identical to
the BSSID.
Using the wrong destination address appears to work with (most)
receivers without MLO, but in MLO some devices are checking for
it carefully, perhaps as a consequence of link to MLD address
translation.
Replace address 3 in the TX_CMD MAC header with the correct
address while retaining the skb address 3 unchanged.
This ensures that skb address 3 will be utilized later for
constructing the A-MSDU subframes.
Note that we fill in the MLD address, but the firmware will do the
necessary translation to link address after encryption.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240204235836.4583a1bf9188.I3f8e7892bdf8f86b4daa28453771a8c9817b2416@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834df ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
kmalloc_array() without __GFP_ZERO flag does not initialize
memory to zero. This causes issues. Use kcalloc() for maps and
bitmap_zalloc() for bitmaps.
Fixes: dd7842878633 ("octeontx2-af: Add new devlink param to configure maximum usable NIX block LFs")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Brett Creeley <bcreeley@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240206024000.1070260-1-rkannoth@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004 005c3fb8 00000001 005c3fb8 00000004 00000001
dfc0: 00000004 005c3fb8 b6f6bba0 00000004 00000004 0059edb8 00000000 00000000
dfe0: 00000004 bed918f0 b6f09bd3 b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw_new resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004 005c3fb8 00000001 005c3fb8 00000004 00000001
dfc0: 00000004 005c3fb8 b6f6bba0 00000004 00000004 0059edb8 00000000 00000000
dfe0: 00000004 bed918f0 b6f09bd3 b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since commit 48e1b4d369cf ("gpiolib: remove the GPIO device from the list
when it's unregistered") we remove the GPIO device entry from the global
list (used to order devices by their GPIO ranges) when unregistering the
chip, not when releasing the device. It will not happen when the last
reference is put anymore. This means, we need to remove it in error path
in gpiochip_add_data_with_key() unconditionally, without checking if the
device's .release() callback is set.
Fixes: 48e1b4d369cf ("gpiolib: remove the GPIO device from the list when it's unregistered")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
TEST_VM_ASYNC_OPS_ERROR is broken and unused. Remove for now and will
pull back in a later time when it is used, fixed, and properly hidden
behind a Kconfig option. Also fixup the supported flags value.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240206045010.2981051-1-matthew.brost@intel.com
(cherry picked from commit d9890c028d66a9e1ee3cccaa081ab5aedcbfe431)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
If GUP fails and we are in_kthread, we can have pinned = 0 and ret = 0.
If that happens we call sg_alloc_append_table_from_pages() with n_pages
= 0, which is not well behaved and can trigger:
kernel BUG at include/linux/scatterlist.h:115!
depending on if the pages array happens to be zeroed or not. Even if we
don't hit that it crashes later when trying to dma_map the returned
table.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202171435.427630-2-matthew.auld@intel.com
(cherry picked from commit 8087199cd5951c1eba26003b3e4296dbb2110adf)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
The calculation to determine max page size of a VMA during a REMAP
operations assumes the VMA has been bound. This assumption is not true
if the VMA is from an eariler operation in an array of binds. If a VMA
has not been bound use the maximum page size which will ensure the
previous / next REMAP operations are not incorrectly skipped.
Fixes: 8f33b4f054fc ("drm/xe: Avoid doing rebinds")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240205231714.2956225-1-matthew.brost@intel.com
(cherry picked from commit 5ad6af5c91e9b942c44b657122270d935db3a813)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
intel_power_domains_init is called twice in xe_device_probe:
1) intel_power_domains_init()
xe_display_init_nommio()
xe_device_probe()
2) intel_power_domains_init()
intel_display_driver_probe_noirq()
xe_display_init_noirq()
xe_device_probe()
It needs remove one to avoid power_domains->power_wells double malloc.
unreferenced object 0xffff88811150ee00 (size 512):
comm "systemd-udevd", pid 506, jiffies 4294674198 (age 3605.560s)
hex dump (first 32 bytes):
10 b4 9d a0 ff ff ff ff ff ff ff ff ff ff ff ff ................
ff ff ff ff ff ff ff ff 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff8134b901>] __kmem_cache_alloc_node+0x1c1/0x2b0
[<ffffffff812c98b2>] __kmalloc+0x52/0x150
[<ffffffffa08b0033>] __set_power_wells+0xc3/0x360 [xe]
[<ffffffffa08562fc>] xe_display_init_nommio+0x4c/0x70 [xe]
[<ffffffffa07f0d1c>] xe_device_probe+0x3c/0x5a0 [xe]
[<ffffffffa082e48f>] xe_pci_probe+0x33f/0x5a0 [xe]
[<ffffffff817f2187>] local_pci_probe+0x47/0xa0
[<ffffffff817f3db3>] pci_device_probe+0xc3/0x1f0
[<ffffffff8192f2a2>] really_probe+0x1a2/0x410
[<ffffffff8192f598>] __driver_probe_device+0x78/0x160
[<ffffffff8192f6ae>] driver_probe_device+0x1e/0x90
[<ffffffff8192f92a>] __driver_attach+0xda/0x1d0
[<ffffffff8192c95c>] bus_for_each_dev+0x7c/0xd0
[<ffffffff8192e159>] bus_add_driver+0x119/0x220
[<ffffffff81930d00>] driver_register+0x60/0x120
[<ffffffffa05e50a0>] 0xffffffffa05e50a0
The call to intel_power_domains_cleanup() needs to stay where it is for
now. The main issue is that while the init is called by the display
side, shared by i915 and xe, the cleanup is called by a non-shared code
path. Fixing that will be done as a separate commit.
Fixes: 44e694958b95 ("drm/xe/display: Implement display support")
Signed-off-by: Xiaoming Wang <xiaoming.wang@intel.com>
[ reword commit message and explain why the fini needs to stay
where it is ]
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202215658.561298-1-lucas.demarchi@intel.com
(cherry picked from commit 86c99abb5f1b6fcd69fb268eeb2e34cb7c4f355c)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
For integrated devices we need to map both mem.kernel_bb_pool and
usm.bb_pool to be able to run batches from both pools.
Fixes: a682b6a42d4d ("drm/xe: Support device page faults on integrated platforms")
Tested-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Brian Welty <brian.welty@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202033440.2351862-1-matthew.brost@intel.com
(cherry picked from commit 72f86ed3c88933d6fa09b036de93621ea71097a7)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
gcc-13 warns about an array overflow that it sees but that is
prevented by the "asid % NUM_PF_QUEUE" calculation:
drivers/gpu/drm/xe/xe_gt_pagefault.c: In function 'xe_guc_pagefault_handler':
include/linux/fortify-string.h:57:33: error: writing 16 bytes into a region of size 0 [-Werror=stringop-overflow=]
include/linux/fortify-string.h:689:26: note: in expansion of macro '__fortify_memcpy_chk'
689 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/xe/xe_gt_pagefault.c:341:17: note: in expansion of macro 'memcpy'
341 | memcpy(pf_queue->data + pf_queue->tail, msg, len * sizeof(u32));
| ^~~~~~
drivers/gpu/drm/xe/xe_gt_types.h:102:25: note: at offset [1144, 265324] into destination object 'tile' of size 8
I found that rewriting the assignment using pointer addition rather than the
equivalent array index calculation prevents the warning, so use that instead.
I sent a bug report against gcc for the false positive warning.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=113214
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103114819.2913937-1-arnd@kernel.org
(cherry picked from commit 774ef5dfc95578a9079426d5106076dcd59c4dfa)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
A REMAP op is composed of 3 VMA's - unmap, prev map, and next map. When
op_execute fails with -EAGAIN we need to update the local VMA pointer to
the current op state and then repin the VMA if it is a userptr.
Fixes a failure seen in xe_vm.munmap-style-unbind-userptr-one-partial.
Fixes: b06d47be7c83 ("drm/xe: Port Xe to GPUVA")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240201004849.2219558-3-matthew.brost@intel.com
(cherry picked from commit 447f74d223b4f6cbab74963bf1099050c15374ce)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Take a reference in xe_exec_queue_last_fence_get(). Also fix a reference
counting underflow bug VM bind and unbind.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240201004849.2219558-2-matthew.brost@intel.com
(cherry picked from commit a856b67a84169e065ebbeee50258936b1eacc9eb)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
The logic for the unwind loop is incorrect resulting in an infinite
loop. Fix to unwind to go from the last operations list to he first.
Fixes: 617eebb9c480 ("drm/xe: Fix array of binds")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240201175532.2303168-1-matthew.brost@intel.com
(cherry picked from commit 3acc1ff1a72fce00cdbd3ef1c27108a967fd5616)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
submit_flushes
atomic_set(&mddev->flush_pending, 1);
rdev_for_each_rcu(rdev, mddev)
atomic_inc(&mddev->flush_pending);
bi->bi_end_io = md_end_flush
submit_bio(bi);
/* flush io is done first */
md_end_flush
if (atomic_dec_and_test(&mddev->flush_pending))
percpu_ref_put(&mddev->active_io)
-> active_io is not released
if (atomic_dec_and_test(&mddev->flush_pending))
-> missing release of active_io
For consequence, mddev_suspend() will wait for 'active_io' to be zero
forever.
Fix this problem by releasing 'active_io' in submit_flushes() if
'flush_pending' is decreased to zero.
Fixes: fa2bbff7b0b4 ("md: synchronize flush io with array reconfiguration")
Cc: stable@vger.kernel.org # v6.1+
Reported-by: Blazej Kucman <blazej.kucman@linux.intel.com>
Closes: https://lore.kernel.org/lkml/20240130172524.0000417b@linux.intel.com/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240201092559.910982-7-yukuai1@huaweicloud.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"Fix regressions in cbc and algif_hash, as well as an older
NULL-pointer dereference in ccp"
* tag 'v6.8-p3' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_hash - Remove bogus SGL free on zero-length error path
crypto: cbc - Ensure statesize is zero
crypto: ccp - Fix null pointer dereference in __sev_platform_shutdown_locked
|
|
Currently kernel supports 8 byte and 16 byte protection information.
So, use ns->head->pi_size instead of sizeof(struct t10_pi_tuple).
Signed-off-by: Francis Pravin <francis.p@samsung.com>
Signed-off-by: Sathyavathi M <sathya.m@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
HDP flush remapping is not done for VFs. Keep the original offsets in VF
environment.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
'stream_enc_regs' array is an array of dcn10_stream_enc_registers
structures. The array is initialized with four elements, corresponding
to the four calls to stream_enc_regs() in the array initializer. This
means that valid indices for this array are 0, 1, 2, and 3.
The error message 'stream_enc_regs' 4 <= 5 below, is indicating that
there is an attempt to access this array with an index of 5, which is
out of bounds. This could lead to undefined behavior
Here, eng_id is used as an index to access the stream_enc_regs array. If
eng_id is 5, this would result in an out-of-bounds access on the
stream_enc_regs array.
Thus fixing Buffer overflow error in dcn301_stream_encoder_create
reported by Smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/resource/dcn301/dcn301_resource.c:1011 dcn301_stream_encoder_create() error: buffer overflow 'stream_enc_regs' 4 <= 5
Fixes: 3a83e4e64bb1 ("drm/amd/display: Add dcn3.01 support to DC (v2)")
Cc: Roman Li <Roman.Li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
After a recent change in LLVM, allmodconfig (which has CONFIG_KCSAN=y
and CONFIG_WERROR=y enabled) has a few new instances of
-Wframe-larger-than for the mode support and system configuration
functions:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn20/display_mode_vba_20v2.c:3393:6: error: stack frame size (2144) exceeds limit (2048) in 'dml20v2_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
3393 | void dml20v2_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
| ^
1 error generated.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn21/display_mode_vba_21.c:3520:6: error: stack frame size (2192) exceeds limit (2048) in 'dml21_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
3520 | void dml21_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
| ^
1 error generated.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn20/display_mode_vba_20.c:3286:6: error: stack frame size (2128) exceeds limit (2048) in 'dml20_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
3286 | void dml20_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
| ^
1 error generated.
Without the sanitizers enabled, there are no warnings.
This was the catalyst for commit 6740ec97bcdb ("drm/amd/display:
Increase frame warning limit with KASAN or KCSAN in dml2") and that same
change was made to dml in commit 5b750b22530f ("drm/amd/display:
Increase frame warning limit with KASAN or KCSAN in dml") but the
frame_warn_flag variable was not applied to all files. Do so now to
clear up the warnings and make all these files consistent.
Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issue/1990
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When dc_state_destruct() was refactored the new phantom_stream_count
and phantom_plane_count members weren't cleared.
Fixes: 012a04b1d6af ("drm/amd/display: Refactor phantom resource allocation")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The present way to fetch VRAM vendor information turns out to be not
reliable on GFX 9.4.3 dGPUs as well. Avoid using the data.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Just ensure that ODM optimization is disabled by default.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Previously we would call apply_ctx_to_hw to enable and disable
phantom pipes. However, apply_ctx_to_hw can potentially update
non-phantom pipes as well which is undesired. Instead of calling
apply_ctx_to_hw as a whole, call the relevant helpers for each
phantom pipe when enabling / disabling which will avoid us modifying
hardware state for non-phantom pipes unknowingly.
The use case is for an FRL display where FRL_Update is requested
by the display. In this case link_state_valid flag is cleared in
a passive callback thread and should be handled in the next stream /
link update. However, due to the call to apply_ctx_to_hw for the
phantom pipes during a flip, the main pipes were modified outside
of the desired sequence (driver does not handle link_state_valid = 0
on flips).
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The change try to fix below error specific to RV platform:
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 4 PID: 917 Comm: sway Not tainted 6.3.9-arch1-1 #1 124dc55df4f5272ccb409f39ef4872fc2b3376a2
Hardware name: LENOVO 20NKS01Y00/20NKS01Y00, BIOS R12ET61W(1.31 ) 07/28/2022
RIP: 0010:drm_dp_atomic_find_time_slots+0x5e/0x260 [drm_display_helper]
Code: 01 00 00 48 8b 85 60 05 00 00 48 63 80 88 00 00 00 3b 43 28 0f 8d 2e 01 00 00 48 8b 53 30 48 8d 04 80 48 8d 04 c2 48 8b 40 18 <48> 8>
RSP: 0018:ffff960cc2df77d8 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff8afb87e81280 RCX: 0000000000000224
RDX: ffff8afb9ee37c00 RSI: ffff8afb8da1a578 RDI: ffff8afb87e81280
RBP: ffff8afb83d67000 R08: 0000000000000001 R09: ffff8afb9652f850
R10: ffff960cc2df7908 R11: 0000000000000002 R12: 0000000000000000
R13: ffff8afb8d7688a0 R14: ffff8afb8da1a578 R15: 0000000000000224
FS: 00007f4dac35ce00(0000) GS:ffff8afe30b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000010ddc6000 CR4: 00000000003506e0
Call Trace:
<TASK>
? __die+0x23/0x70
? page_fault_oops+0x171/0x4e0
? plist_add+0xbe/0x100
? exc_page_fault+0x7c/0x180
? asm_exc_page_fault+0x26/0x30
? drm_dp_atomic_find_time_slots+0x5e/0x260 [drm_display_helper 0e67723696438d8e02b741593dd50d80b44c2026]
? drm_dp_atomic_find_time_slots+0x28/0x260 [drm_display_helper 0e67723696438d8e02b741593dd50d80b44c2026]
compute_mst_dsc_configs_for_link+0x2ff/0xa40 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054]
? fill_plane_buffer_attributes+0x419/0x510 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054]
compute_mst_dsc_configs_for_state+0x1e1/0x250 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054]
amdgpu_dm_atomic_check+0xecd/0x1190 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054]
drm_atomic_check_only+0x5c5/0xa40
drm_mode_atomic_ioctl+0x76e/0xbc0
? _copy_to_user+0x25/0x30
? drm_ioctl+0x296/0x4b0
? __pfx_drm_mode_atomic_ioctl+0x10/0x10
drm_ioctl_kernel+0xcd/0x170
drm_ioctl+0x26d/0x4b0
? __pfx_drm_mode_atomic_ioctl+0x10/0x10
amdgpu_drm_ioctl+0x4e/0x90 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054]
__x64_sys_ioctl+0x94/0xd0
do_syscall_64+0x60/0x90
? do_syscall_64+0x6c/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7f4dad17f76f
Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <89> c>
RSP: 002b:00007ffd9ae859f0 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 000055e255a55900 RCX: 00007f4dad17f76f
RDX: 00007ffd9ae85a90 RSI: 00000000c03864bc RDI: 000000000000000b
RBP: 00007ffd9ae85a90 R08: 0000000000000003 R09: 0000000000000003
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000c03864bc
R13: 000000000000000b R14: 000055e255a7fc60 R15: 000055e255a01eb0
</TASK>
Modules linked in: rfcomm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device ccm cmac algif_hash algif_skcipher af_alg joydev mousedev bnep >
typec libphy k10temp ipmi_msghandler roles i2c_scmi acpi_cpufreq mac_hid nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_mas>
CR2: 0000000000000008
---[ end trace 0000000000000000 ]---
RIP: 0010:drm_dp_atomic_find_time_slots+0x5e/0x260 [drm_display_helper]
Code: 01 00 00 48 8b 85 60 05 00 00 48 63 80 88 00 00 00 3b 43 28 0f 8d 2e 01 00 00 48 8b 53 30 48 8d 04 80 48 8d 04 c2 48 8b 40 18 <48> 8>
RSP: 0018:ffff960cc2df77d8 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff8afb87e81280 RCX: 0000000000000224
RDX: ffff8afb9ee37c00 RSI: ffff8afb8da1a578 RDI: ffff8afb87e81280
RBP: ffff8afb83d67000 R08: 0000000000000001 R09: ffff8afb9652f850
R10: ffff960cc2df7908 R11: 0000000000000002 R12: 0000000000000000
R13: ffff8afb8d7688a0 R14: ffff8afb8da1a578 R15: 0000000000000224
FS: 00007f4dac35ce00(0000) GS:ffff8afe30b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000010ddc6000 CR4: 00000000003506e0
With a second DP monitor connected, drm_atomic_state in dm atomic check
sequence does not include the connector state for the old/existing/first
DP monitor. In such case, dsc determination policy would hit a null ptr
when it tries to iterate the old/existing stream that does not have a
valid connector state attached to it. When that happens, dm atomic check
should call drm_atomic_get_connector_state for a new connector state.
Existing dm has already done that, except for RV due to it does not have
official support of dsc where .num_dsc is not defined in dcn10 resource
cap, that prevent from getting drm_atomic_get_connector_state called.
So, skip dsc determination policy for ASICs that don't have DSC support.
Cc: stable@vger.kernel.org # 6.1+
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2314
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
ta if invoke node buffer
|-------- ta type ----------|
|-------- ta id ----------|
|-------- cmd id ----------|
|------ shared buf len -----|
|------ shared buffer ------|
ta if invoke node buffer is as above, copy shared buffer data to correct location
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
To match firmware measurements and avoid hanging when accessing HW
that's in idle.
[How]
Increase the delays to what we've measured.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A supplement to commit: 615dd56ac5379f4239940be69139a33e79e59c67
There is an irq warning of jpeg during resume in s2idle process. No irq enabled in jpeg 4.0.5 resume.
Fixes: 615dd56ac537 ("drm/amdgpu: remove asymmetrical irq disabling in vcn 4.0.5 suspend")
Signed-off-by: Li Ma <li.ma@amd.com>
Acked-By: Saleemkhan Jamadar <saleemkhan.jamadar@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Veerabadhran Gopalakrishnan <Veerabadhran.Gopalakrishnan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In the s3 suspend abort case some type of gfx9 power
rail not turn off from FCH side and this will put the
GPU in an unknown power status, so let's reset the gpu
to a known good power state before reinitialize gpu
device.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In the suspend abort cases, the gfx power rail doesn't turn off so
some GFXDEC registers/CSB can't reset to default value and at this
moment reinitialize GFXDEC/CSB will result in an unexpected error.
So let skip those program sequence for the suspend abort case.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
When populating dml pipes, odm combine policy should be assigned based
on the pipe topology of the context passed in. DML pipes could be
repopulated multiple times during single validate bandwidth attempt. We
need to make sure that whenever we repopulate the dml pipes it is always
aligned with the updated context. There is a case where DML pipes get
repopulated during FPO optimization after ODM combine policy is changed.
Since in the current code we reinitlaize ODM combine policy, even though
the current context has ODM combine enabled, we overwrite it despite the
pipes are already split. This causes DML to think that MPC combine is
used so we mistakenly enable MPC combine because we apply pipe split
with ODM combine policy reset. This issue doesn't impact non windowed
MPO with ODM case because the legacy policy has restricted use cases. We
don't encounter the case where both ODM and FPO optimizations are
enabled together. So we decide to leave it as is because it is about to
be replaced anyway.
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In "u32 otg_inst = pipe_ctx->stream_res.tg->inst;"
pipe_ctx->stream_res.tg could be NULL, it is relying on the caller to
ensure the tg is not NULL.
Fixes: 474ac4a875ca ("drm/amd/display: Implement some asic specific abm call backs.")
Cc: Yongqiang Sun <yongqiang.sun@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
'panel_cntl' structure used to control the display panel could be null,
dereferencing it could lead to a null pointer access.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn21/dcn21_hwseq.c:269 dcn21_set_backlight_level() error: we previously assumed 'panel_cntl' could be null (see line 250)
Fixes: 474ac4a875ca ("drm/amd/display: Implement some asic specific abm call backs.")
Cc: Yongqiang Sun <yongqiang.sun@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
I recently changed the alignment code in dw_pcie_ep_raise_msix_irq(). The
code in dw_pcie_ep_raise_msi_irq() is similar, so update it to match, just
for consistency. (No effect on runtime, just a cleanup).
Link: https://lore.kernel.org/r/184097e0-c728-42c7-9e8a-556bd33fb612@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The "msg_addr" variable is u64. However, the "aligned_offset" is an
unsigned int. This means that when the code does:
msg_addr &= ~aligned_offset;
it will unintentionally zero out the high 32 bits. Use ALIGN_DOWN() to do
the alignment instead.
Fixes: 2217fffcd63f ("PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support")
Link: https://lore.kernel.org/r/af59c7ad-ab93-40f7-ad4a-7ac0b14d37f5@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org>
|
|
The functions and the attribute listed in the comment doesn't exists in
the code, (ns->logging_enabled, nvme_passthru_err_log_enabled_store()
and nvme_passthru_err_log_enabled_show())
Update the comment with right function names and a comment
ns->head->passthru_err_log_enabled,
nvme_io_passthru_err_log_enabled_store() and
nvme_io_passthru_err_log_enabled_show().
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Alan Adamson <alan.adamson@oracle.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.8-rc4
This time we have unusually large wireless pull request. Several
functionality fixes to both stack and iwlwifi. Lots of fixes to
warnings, especially to MODULE_DESCRIPTION().
* tag 'wireless-2024-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (31 commits)
wifi: mt76: mt7996: fix fortify warning
wifi: brcmfmac: Adjust n_channels usage for __counted_by
wifi: iwlwifi: do not announce EPCS support
wifi: iwlwifi: exit eSR only after the FW does
wifi: iwlwifi: mvm: fix a battery life regression
wifi: mac80211: accept broadcast probe responses on 6 GHz
wifi: mac80211: adding missing drv_mgd_complete_tx() call
wifi: mac80211: fix waiting for beacons logic
wifi: mac80211: fix unsolicited broadcast probe config
wifi: mac80211: initialize SMPS mode correctly
wifi: mac80211: fix driver debugfs for vif type change
wifi: mac80211: set station RX-NSS on reconfig
wifi: mac80211: fix RCU use in TDLS fast-xmit
wifi: mac80211: improve CSA/ECSA connection refusal
wifi: cfg80211: detect stuck ECSA element in probe resp
wifi: iwlwifi: remove extra kernel-doc
wifi: fill in MODULE_DESCRIPTION()s for mt76 drivers
wifi: fill in MODULE_DESCRIPTION()s for wilc1000
wifi: fill in MODULE_DESCRIPTION()s for wl18xx
wifi: fill in MODULE_DESCRIPTION()s for p54spi
...
====================
Link: https://lore.kernel.org/r/20240206095722.CD9D2C433F1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The namespace does not have attributes, but the head does. Move the new
logging attribute to that structure instead of dereferencing the wrong
type.
And while we're here, fix the reverse-tree coding style.
Fixes: 9f079dda14339e ("nvme: allow passthru cmd error logging")
Reported-by: Tasmiya Nalatwad <tasmiya@linux.vnet.ibm.com>
Tested-by: Tasmiya Nalatwad <tasmiya@linux.vnet.ibm.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Alan Adamson <alan.adamson@oracle.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
The kernel build regressions/improvements email contained a couple of
issues with old compilers (in fact all the reports were on different
architectures, but all gcc 5.5) and the FIELD_PREP() and FIELD_GET()
conversions. They're all because an integer #define that should have
been declared as unsigned, was shifted to the point that it could set
the sign bit.
The fix just involves making sure the defines use the "U" identifier on
the constants to make sure they're unsigned. Should make the checkers
happier.
Confirmed with objdump before/after that there is no change to the
binaries.
Issues were reported as follows:
./drivers/net/ethernet/intel/ice/ice_base.c:238:7: note: in expansion of macro 'FIELD_GET'
(FIELD_GET(GLINT_CTL_ITR_GRAN_25_M, regval) == ICE_ITR_GRAN_US))
^
./include/linux/compiler_types.h:435:38: error: call to '__compiletime_assert_1093' declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_nvm.c:709:16: note: in expansion of macro ‘FIELD_GET’
orom->major = FIELD_GET(ICE_OROM_VER_MASK, combo_ver);
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_796’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_common.c:945:18: note: in expansion of macro ‘FIELD_GET’
u8 max_agg_bw = FIELD_GET(GL_PWR_MODE_CTL_CAR_MAX_BW_M,
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_420’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/i40e/i40e_dcb.c:458:8: note: in expansion of macro ‘FIELD_GET’
oui = FIELD_GET(I40E_LLDP_TLV_OUI_MASK, ouisubtype);
^
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/lkml/d03e90ca-8485-4d1b-5ec1-c3398e0e8da@linux-m68k.org/ #i40e #ice
Fixes: 62589808d73b ("i40e: field get conversion")
Fixes: 5a259f8e0baf ("ice: field get conversion")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20240206022906.2194214-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-linus
Georgi writes:
interconnect fixes for v6.8-rc
These are tiny fixes for reported issues in driver code for a few
platforms. One of them sorts out a hang issue, the other improves
the power consumption and the rest are fixing some bitmasks to make
sure the hardware does thing right.
- interconnect: qcom: sc8180x: Mark CO0 BCM keepalive
- interconnect: qcom: sm8550: Enable sync_state
- interconnect: qcom: sm8650: Use correct ACV enable_mask
- interconnect: qcom: x1e80100: Add missing ACV enable_mask
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: x1e80100: Add missing ACV enable_mask
interconnect: qcom: sm8650: Use correct ACV enable_mask
interconnect: qcom: sm8550: Enable sync_state
interconnect: qcom: sc8180x: Mark CO0 BCM keepalive
|
|
The raw noinc write test places a known value in the register following
the noinc register to verify that it is not disturbed by the noinc
write. This test ensures this value is distinct by adding 100 to the
second element of the noinc write data.
The regmap registers are 16-bit, while the test value is stored in an
unsigned int. Therefore, adding 100 may cause the register to wrap while
the test value does not, causing the test to fail. This patch fixes this
by changing val_test and val_last from unsigned int to u16.
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/linux-kernel/745d3a11-15bc-48b6-84c8-c8761c943bed@roeck-us.net/T/
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240206151004.1636761-2-ben.wolsieffer@hefring.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of incrementing the base of the global reg fields, which renders
the second instance of the repeater broken due to wrong offsets, use
regmap with base and offset. As for zeroing out the rest of the tuning
regs, avoid looping though the table and just use the table as is,
as it is already zero initialized.
Fixes: 99a517a582fc ("phy: qualcomm: phy-qcom-eusb2-repeater: Zero out untouched tuning regs")
Tested-by: Elliot Berman <quic_eberman@quicinc.com> # sm8650-qrd
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240201-phy-qcom-eusb2-repeater-fixes-v4-1-cf18c8cef6d7@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
It should be 'qphy->vreg' passed to PTR_ERR() when devm_regulator_get() fails.
Fixes: 08e49af50701 ("phy: qcom: Introduce M31 USB PHY driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/20230824091345.1072650-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Devicetree spec lists only dashes as valid characters for alias names.
Table 3.2: Valid characters for alias names, Devicee Specification,
Release v0.4
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Fixes: 3fbae284887de ("phy: freescale: phy-fsl-imx8-mipi-dphy: Add i.MX8qxp LVDS PHY mode support")
Link: https://lore.kernel.org/r/20240110093343.468810-1-alexander.stein@ew.tq-group.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
As explained by a comment in <linux/u64_stats_sync.h>, write side of struct
u64_stats_sync must ensure mutual exclusion, or one seqcount update could
be lost on 32-bit platforms, thus blocking readers forever. Such lockups
have been observed in real world after stmmac_xmit() on one CPU raced with
stmmac_napi_poll_tx() on another CPU.
To fix the issue without introducing a new lock, split the statics into
three parts:
1. fields updated only under the tx queue lock,
2. fields updated only during NAPI poll,
3. fields updated only from interrupt context,
Updates to fields in the first two groups are already serialized through
other locks. It is sufficient to split the existing struct u64_stats_sync
so that each group has its own.
Note that tx_set_ic_bit is updated from both contexts. Split this counter
so that each context gets its own, and calculate their sum to get the total
value in stmmac_get_ethtool_stats().
For the third group, multiple interrupts may be processed by different CPUs
at the same time, but interrupts on the same CPU will not nest. Move fields
from this group to a newly created per-cpu struct stmmac_pcpu_stats.
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Link: https://lore.kernel.org/netdev/Za173PhviYg-1qIn@torres.zugschlus.de/t/
Cc: stable@vger.kernel.org
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'nbytes' should be equivalent to burst * width in audio multi-fifo
setups. Given that the FIFO width is fixed at 32 bits, adjusts the burst
size for multi-fifo configurations to match the slave maxburst in the
configuration.
Cc: stable@vger.kernel.org
Fixes: 72f5801a4e2b ("dmaengine: fsl-edma: integrate v3 support")
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240131163318.360315-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Initialize the qDMA irqs after the registers are configured so that
interrupts that may have been pending from a primary kernel don't get
processed by the irq handler before it is ready to and cause panic with
the following trace:
Call trace:
fsl_qdma_queue_handler+0xf8/0x3e8
__handle_irq_event_percpu+0x78/0x2b0
handle_irq_event_percpu+0x1c/0x68
handle_irq_event+0x44/0x78
handle_fasteoi_irq+0xc8/0x178
generic_handle_irq+0x24/0x38
__handle_domain_irq+0x90/0x100
gic_handle_irq+0x5c/0xb8
el1_irq+0xb8/0x180
_raw_spin_unlock_irqrestore+0x14/0x40
__setup_irq+0x4bc/0x798
request_threaded_irq+0xd8/0x190
devm_request_threaded_irq+0x74/0xe8
fsl_qdma_probe+0x4d4/0xca8
platform_drv_probe+0x50/0xa0
really_probe+0xe0/0x3f8
driver_probe_device+0x64/0x130
device_driver_attach+0x6c/0x78
__driver_attach+0xbc/0x158
bus_for_each_dev+0x5c/0x98
driver_attach+0x20/0x28
bus_add_driver+0x158/0x220
driver_register+0x60/0x110
__platform_driver_register+0x44/0x50
fsl_qdma_driver_init+0x18/0x20
do_one_initcall+0x48/0x258
kernel_init_freeable+0x1a4/0x23c
kernel_init+0x10/0xf8
ret_from_fork+0x10/0x18
Cc: stable@vger.kernel.org
Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Signed-off-by: Yi Zhao <yi.zhao@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240201220406.440145-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There is chip (ls1028a) errata:
The SoC may hang on 16 byte unaligned read transactions by QDMA.
Unaligned read transactions initiated by QDMA may stall in the NOC
(Network On-Chip), causing a deadlock condition. Stalled transactions will
trigger completion timeouts in PCIe controller.
Workaround:
Enable prefetch by setting the source descriptor prefetchable bit
( SD[PF] = 1 ).
Implement this workaround.
Cc: stable@vger.kernel.org
Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240201215007.439503-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
