| Age | Commit message (Collapse) | Author |
|---|
|
The VCU allows to specify the QP per frame and coding unit. A buffer
that specifies the QP is passed via the ep2 field in the ENCODE_FRAME
message.
The driver currently does not support the external QP table. Simplify
the driver by not setting the ep2 fields at all.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The fields for the number of rows and columns in the encode frame
response message are switched. This causes broken PPS, if the encoder
uses tiles for encoding and the number of rows and columns differ.
Write the fields of the response message into the correct fields of the
the internal data structure when parsing the response message.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The encoder buffer can have a negative impact on the quality of the
encoded video.
Add a control to allow user space to disable the encoder buffer per
channel if the VCU supports the encoder buffer but the quality is not
sufficient.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The encoder buffer serves as a cache for reference frames during the
encoding process. The encoder buffer significantly reduces the bandwidth
requirement for read accesses on the AXI ports of the VCU, but slightly
reduces the quality of the encoded video.
The encoder buffer must be configured as a whole during the firmware
initialization and later explicitly enabled for every channel that shall
use the encoder buffer.
Prior to firmware version 2019.2, it was necessary to explicitly set the
size of the encoder buffer for every channel. Since 2019.2 it is
sufficient to enable the encoder buffer and leave the rest to the
firmware. Therefore, only support the encoder buffer for firmware 2019.2
and later.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The allegro driver must ensure that the mcu and core clocks are enabled
and set to the expected clock rate before trying to load the firmware
and to reset the MCU.
Up until now, the driver assumed that the clocks are always enabled in
the PL (programming logic), because the xlnx_vcu driver did not export
the clocks to other drivers. This has changed and by explicitly enabling
the clocks in the driver, this assumption can be dropped.
It might even be possible to disable the clocks for the encoder if the
encoder is not used. However, the behavior is not documented and it
might be necessary to reinitialize the encoder after deactivating the
clocks. Play it safe by sticking to the current behavior.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The VCU provides information about its configuration in a dedicated
register space. These settings include, for example, the expected clock
rates and the configuration of the encoder buffer. In the device tree,
the settings are described by the "xlnx,vcu-settings" compatible.
The settings are needed to correctly configure the clocks and the
encoder buffer.
Lookup the VCU settings in the device tree and make it accessible to the
driver via a regmap.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
If the module probe finished, but the firmware initialization failed,
removing the module must not revert the firmware initialization.
Add a field to track the status of the firmware initialization and only
roll it back, if the firmware was successfully initialized.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The mailbox is initialized after the interrupt handler is installed. As
the firmware is loaded and started even later, it should not happen that
the interrupt occurs without the mailbox being initialized.
As the Linux Driver Verification project (linuxtesting.org) keeps
reporting this as an error, add a check to ignore interrupts before the
mailbox is initialized to fix this potential null pointer dereference.
Reported-by: Yuri Savinykh <s02190703@gse.cs.msu.ru>
Reported-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
arm/fixes
Reset controller fixes for v5.15
Fix the status bit polarity in the brcmstb-rescal driver, re-enable
pistachio driver selection after MACH_PISTACHIO removal, add transfer
error handling in the tegra-bpmp driver, and fix probing of the
reset-socfpga driver after recent device link changes.
* tag 'reset-fixes-for-v5.15' of git://git.pengutronix.de/pza/linux:
reset: socfpga: add empty driver allowing consumers to probe
reset: tegra-bpmp: Handle errors in BPMP response
reset: pistachio: Re-enable driver selection
reset: brcmstb-rescal: fix incorrect polarity of status bit
Link: https://lore.kernel.org/r/b378f2aae54538db6a13c98561b4cbcacbef937c.camel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
bch_crc64_update is an entirely pointless wrapper around crc64_be.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20211020143812.6403-9-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Using local kmaps slightly reduces the chances to stray writes, and
the bvec interface cleans up the code a little bit.
Also switch from page_address to bvec_kmap_local for cbv to be on the
safe side and to avoid pointlessly poking into bvec internals.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20211020143812.6403-8-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Just use the %pg format specifier to print the name directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20211020143812.6403-7-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Just use the %pg format specifier to print the name directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20211020143812.6403-6-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Calculation of cache_set's cached sectors is done by travelling
cached_devs list as shown below:
static void calc_cached_dev_sectors(struct cache_set *c)
{
...
list_for_each_entry(dc, &c->cached_devs, list)
sectors += bdev_sectors(dc->bdev);
c->cached_dev_sectors = sectors;
}
But cached_dev won't be unlinked from c->cached_devs list until we call
following list_move(&dc->list, &uncached_devices),
so previous fix in 'commit 46010141da6677b81cc77f9b47f8ac62bd1cbfd3
("bcache: recal cached_dev_sectors on detach")' is wrong, now we move
it to its right place.
Signed-off-by: Lin Feng <linf@wangsu.com>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20211020143812.6403-5-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In register_bcache(), there are several cases we didn't set
correct error info (return value and/or error message):
- if kzalloc() fails, it needs to return ENOMEM and print
"cannot allocate memory";
- if register_cache() fails, it's better to propagate its
return value rather than using default EINVAL.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20211020143812.6403-4-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
acqurie -> acquire
Signed-off-by: Ding Senjie <dingsenjie@yulong.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20211020143812.6403-2-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
__dasd_device_check_path_events() calls the discipline path event handler.
This handler can leave the 'to be verified pathmask' populated for an
additional verification.
There is a race window where the worker has finished before
dasd_path_clear_all_verify() is called which resets the tbvpm.
Due to this there could be outstanding path verifications missed.
Fix by clearing the pathmasks before calling the handler and add them
again in case of an error.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20211020115124.1735254-8-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
dasd_eckd_path_available_action() does a memory allocation to store
the per path configuration data permanently.
In the unlikely case that this allocation fails there is no conf_data
stored for the corresponding path.
This is OK since this is not necessary for an operational path but some
features like control unit initiated reconfiguration (CUIR) do not work.
To fix this add the path to the 'to be verified pathmask' again and
schedule the handler again.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20211020115124.1735254-7-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Summarize the dasd configuration data in a separate structure so that
functions that need temporary config data do not need to allocate the
whole eckd_private structure.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20211020115124.1735254-6-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
dasd_eckd_read_conf is called multiple times during device setup but the
fc_security feature needs to be read only once. So move it into the calling
function.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20211020115124.1735254-5-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the cabling check out of dasd_eckd_read_conf and split it up into
separate functions to improve readability and re-use functions.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20211020115124.1735254-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fix this:
drivers/s390/block/dasd_ioctl.c:666: warning:
Function parameter or member 'disk' not described in 'dasd_biodasdinfo'
drivers/s390/block/dasd_ioctl.c:666: warning:
Function parameter or member 'info' not described in 'dasd_biodasdinfo'
Acked-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20211020115124.1735254-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Get rid of the rather odd casts to character pointer of the
dasd_ccw_req magic member and simply use the unsigned int value
unmodified everywhere.
Acked-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20211020115124.1735254-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
I got issue as follows:
[ 263.886511] BUG: KASAN: use-after-free in pid_show+0x11f/0x13f
[ 263.888359] Read of size 4 at addr ffff8880bf0648c0 by task cat/746
[ 263.890479] CPU: 0 PID: 746 Comm: cat Not tainted 4.19.90-dirty #140
[ 263.893162] Call Trace:
[ 263.893509] dump_stack+0x108/0x15f
[ 263.893999] print_address_description+0xa5/0x372
[ 263.894641] kasan_report.cold+0x236/0x2a8
[ 263.895696] __asan_report_load4_noabort+0x25/0x30
[ 263.896365] pid_show+0x11f/0x13f
[ 263.897422] dev_attr_show+0x48/0x90
[ 263.898361] sysfs_kf_seq_show+0x24d/0x4b0
[ 263.899479] kernfs_seq_show+0x14e/0x1b0
[ 263.900029] seq_read+0x43f/0x1150
[ 263.900499] kernfs_fop_read+0xc7/0x5a0
[ 263.903764] vfs_read+0x113/0x350
[ 263.904231] ksys_read+0x103/0x270
[ 263.905230] __x64_sys_read+0x77/0xc0
[ 263.906284] do_syscall_64+0x106/0x360
[ 263.906797] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reproduce this issue as follows:
1. nbd-server 8000 /tmp/disk
2. nbd-client localhost 8000 /dev/nbd1
3. cat /sys/block/nbd1/pid
Then trigger use-after-free in pid_show.
Reason is after do step '2', nbd-client progress is already exit. So
it's task_struct already freed.
To solve this issue, revert part of 6521d39a64b3's modify and remove
useless 'recv_task' member of nbd_device.
Fixes: 6521d39a64b3 ("nbd: Remove variable 'pid'")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20211020073959.2679255-1-yebin10@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff88800906c618 (size 8):
comm "i2c-idt82p33931", pid 4421, jiffies 4294948083 (age 13.188s)
hex dump (first 8 bytes):
70 74 70 30 00 00 00 00 ptp0....
backtrace:
[<00000000312ed458>] __kmalloc_track_caller+0x19f/0x3a0
[<0000000079f6e2ff>] kvasprintf+0xb5/0x150
[<0000000026aae54f>] kvasprintf_const+0x60/0x190
[<00000000f323a5f7>] kobject_set_name_vargs+0x56/0x150
[<000000004e35abdd>] dev_set_name+0xc0/0x100
[<00000000f20cfe25>] ptp_clock_register+0x9f4/0xd30 [ptp]
[<000000008bb9f0de>] idt82p33_probe.cold+0x8b6/0x1561 [ptp_idt82p33]
When posix_clock_register() returns an error, the name allocated
in dev_set_name() will be leaked, the put_device() should be used
to give up the device reference, then the name will be freed in
kobject_cleanup() and other memory will be freed in ptp_clock_release().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: a33121e5487b ("ptp: fix the race between the release of ptp_clock and cdev")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When utilizing End to End delay mechanism, the following error messages show up:
|root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m
|ptp4l[950.573]: selected /dev/ptp3 as PTP clock
|ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1
|ptp4l[956.879]: selected best master clock 001395.fffe.4897b4
|ptp4l[956.879]: port 1: assuming the grand master role
|ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER
|ptp4l[962.017]: port 1: received DELAY_REQ without timestamp
|ptp4l[962.273]: port 1: received DELAY_REQ without timestamp
|ptp4l[963.090]: port 1: received DELAY_REQ without timestamp
Commit f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP
packets in dwmac v5.10a") already addresses this problem for the dwmac
v5.10. However, same holds true for all dwmacs above version v4.10. Correct the
check accordingly. Afterwards everything works as expected.
Tested on Intel Atom(R) x6414RE Processor.
Fixes: 14f347334bf2 ("net: stmmac: Correctly take timestamp for PTPv2")
Fixes: f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a")
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If something goes wrong in the remove callback, returning an error code
just results in an error message. The device still disappears.
So don't skip disabling the regulator in st95hf_remove() if resetting
the controller via spi fails. Also don't return an error code which just
results in two error messages.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coverity complains of a possible dereference of a null return value.
5. returned_null: kzalloc returns NULL. [show details]
6. var_assigned: Assigning: si_data = NULL return value from kzalloc.
488 si_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
489 cbd.length = cpu_to_le16(data_size);
490
491 dma = dma_map_single(&priv->si->pdev->dev, si_data,
492 data_size, DMA_FROM_DEVICE);
While this kzalloc() is unlikely to fail, I did notice that the function
returned without unmapping si_data.
Fix this by refactoring the error paths and checking for kzalloc()
failure.
Fixes: 888ae5a3952ba ("net: enetc: add tc flower psfp offload driver")
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coverity complains of unsigned compare against 0. There are 2 cases in
this function:
1821 itp = (irq_holdoff * 1000) / p->desc->qman_256_cycles_per_ns;
CID 121131 (#1 of 1): Unsigned compared against 0 (NO_EFFECT)
unsigned_compare: This less-than-zero comparison of an unsigned value is never true. itp < 0U.
1822 if (itp < 0 || itp > 4096) {
1823 max_holdoff = (p->desc->qman_256_cycles_per_ns * 4096) / 1000;
1824 pr_err("irq_holdoff must be between 0..%dus\n", max_holdoff);
1825 return -EINVAL;
1826 }
1827
unsigned_compare: This less-than-zero comparison of an unsigned value is never true. irq_threshold < 0U.
1828 if (irq_threshold >= p->dqrr.dqrr_size || irq_threshold < 0) {
1829 pr_err("irq_threshold must be between 0..%d\n",
1830 p->dqrr.dqrr_size - 1);
1831 return -EINVAL;
1832 }
Fix this by removing the comparisons altogether as they are incorrect. Zero is
a possible value in either case. Also fix a minor comment typo and update the
2 pr_err() calls to use %u formatting as well as be more precise regarding
the exact error.
Fixes: ed1d2143fee5 ("soc: fsl: dpio: add support for irq coalescing per software portal")
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Roy Pledge <Roy.Pledge@nxp.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tidy and organize qca8k setup function from multiple for loop.
Change for loop in bridge leave/join to scan all port and skip cpu port.
No functional change intended.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-19
This series contains updates to ice driver only.
Brett implements support for ndo_set_vf_rate allowing for min_tx_rate
and max_tx_rate to be set for a VF.
Jesse updates DIM moderation to improve latency and resolves problems
with reported rate limit and extra software generated interrupts.
Wojciech moves a check for trusted VFs to the correct function,
disables lb_en for switchdev offloads, and refactors ethtool ops due
to differences in support for PF and port representor support.
Cai Huoqing utilizes the helper function devm_add_action_or_reset().
Gustavo A. R. Silva replaces uses of allocation to devm_kcalloc() as
applicable.
Dan Carpenter propagates an error instead of returning success.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, do the swapping, then
call eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.
When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.
This patch fix it by disable SRIOV before remove hclge.ko.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The task of VF reset is performed through the workqueue. It checks the
value of hdev->reset_pending to determine whether to exit the loop.
However, the value of hdev->reset_pending may also be assigned by
the interrupt function hclgevf_misc_irq_handle(), which may cause the
loop fail to exit and keep occupying the workqueue. This loop is not
necessary, so remove it and the workqueue will be rescheduled if the
reset needs to be retried or a new reset occurs.
Fixes: 1cc9bc6e5867 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when there is a rx page allocation failure, it is
possible that polling may be stopped if there is no more packet
to be reveiced, which may cause queue stall problem under memory
pressure.
This patch makes sure polling is scheduled again when there is
any rx page allocation failure, and polling will try to allocate
receive buffers until it succeeds.
Now the allocation retry is added, it is unnecessary to do the rx
page allocation at the end of rx cleaning, so remove it. And reset
the unused_count to zero after calling hns3_nic_alloc_rx_buffers()
to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under
memory pressure.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.
This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.
This patch updates the max tx size according to the manual.
Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP
mode. In this case, this tc may occupy all the tx bandwidth if it has
huge traffic, so it violates the purpose of the user setting.
To fix this problem, limit the ets dwrr bandwidth must greater than 0.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, DWRR of tc will be initialized to a fixed value when this tc
is enabled, but it is not been reset to 0 when this tc is disabled. It
cause a problem that the DWRR of unused tc is not 0 after using tc tool
to add and delete multi-tc parameters.
For examples, after enabling 4 TCs and restoring to 1 TC by follow
tc commands:
$ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \
8@0 8@8 8@16 8@24 hw 1 mode channel
$ tc qdisc del dev eth0 root
Now there is just one TC is enabled for eth0, but the tc info querying by
debugfs is shown as follow:
$ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info
enabled tc number: 1
weight_offset: 14
TC MODE WEIGHT
0 dwrr 100
1 dwrr 100
2 dwrr 100
3 dwrr 100
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
This patch fixes it by resetting DWRR of tc to 0 when tc is disabled.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add configuration of interrupt type and fifo interrupt enable of TM QCN
error event if enabled, otherwise this event will not be reported when
there is error.
Fixes: d914971df022 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change does not fix any functional issue or address any real life
use case that wasn't possible before. It is just a small step in the
process of standardizing the way in which Ethernet MAC drivers may apply
RGMII delays (traditionally these have been applied by PHYs, with no
clear definition of what to do in the case of a fixed-link).
The sja1105 driver used to apply MAC-level RGMII delays on the RX data
lines when in fixed-link mode and using a phy-mode of "rgmii-rxid" or
"rgmii-id" and on the TX data lines when using "rgmii-txid" or "rgmii-id".
But the standard definitions don't say anything about behaving
differently when the port is in fixed-link vs when it isn't, and the new
device tree bindings are about having a way of applying the delays in a
way that is independent of the phy-mode and of the fixed-link property.
When the {rx,tx}-internal-delay-ps properties are present, use them,
otherwise fall back to the old behavior and warn.
One other thing to note is that the SJA1105 hardware applies a delay
value in degrees rather than in picoseconds (the delay in ps changes
depending on the frequency of the RGMII clock - 125 MHz at 1G, 25 MHz at
100M, 2.5MHz at 10M). I assume that is fine, we calculate the phase
shift of the internal delay lines assuming that the device tree meant
gigabit, and we let the hardware scale those according to the link speed.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210723173108.459770-6-prasanna.vengateshan@microchip.com/
Link: https://patchwork.ozlabs.org/project/netdev/patch/20200616074955.GA9092@laureti-dev/#2461123
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 09e856d54bda5f288ef8437a90ab2b9b3eab83d1.
When an interface is enslaved in a VRF, prerouting conntrack hook is
called twice: once in the context of the original input interface, and
once in the context of the VRF interface. If no special precausions are
taken, this leads to creation of two conntrack entries instead of one,
and breaks SNAT.
Commit above was intended to avoid creation of extra conntrack entries
when input interface is enslaved in a VRF. It did so by resetting
conntrack related data associated with the skb when it enters VRF context.
However it breaks netfilter operation. Imagine a use case when conntrack
zone must be assigned based on the original input interface, rather than
VRF interface (that would make original interfaces indistinguishable). One
could create netfilter rules similar to these:
chain rawprerouting {
type filter hook prerouting priority raw;
iif realiface1 ct zone set 1 return
iif realiface2 ct zone set 2 return
}
This works before the mentioned commit, but not after: zone assignment
is "forgotten", and any subsequent NAT or filtering that is dependent
on the conntrack zone does not work.
Here is a reproducer script that demonstrates the difference in behaviour.
==========
#!/bin/sh
# This script demonstrates unexpected change of nftables behaviour
# caused by commit 09e856d54bda5f28 ""vrf: Reset skb conntrack
# connection on VRF rcv"
# https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1
#
# Before the commit, it was possible to assign conntrack zone to a
# packet (or mark it for `notracking`) in the prerouting chanin, raw
# priority, based on the `iif` (interface from which the packet
# arrived).
# After the change, # if the interface is enslaved in a VRF, such
# assignment is lost. Instead, assignment based on the `iif` matching
# the VRF master interface is honored. Thus it is impossible to
# distinguish packets based on the original interface.
#
# This script demonstrates this change of behaviour: conntrack zone 1
# or 2 is assigned depending on the match with the original interface
# or the vrf master interface. It can be observed that conntrack entry
# appears in different zone in the kernel versions before and after
# the commit.
IPIN=172.30.30.1
IPOUT=172.30.30.2
PFXL=30
ip li sh vein >/dev/null 2>&1 && ip li del vein
ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf
nft list table testct >/dev/null 2>&1 && nft delete table testct
ip li add vein type veth peer veout
ip li add tvrf type vrf table 9876
ip li set veout master tvrf
ip li set vein up
ip li set veout up
ip li set tvrf up
/sbin/sysctl -w net.ipv4.conf.veout.accept_local=1
/sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0
ip addr add $IPIN/$PFXL dev vein
ip addr add $IPOUT/$PFXL dev veout
nft -f - <<__END__
table testct {
chain rawpre {
type filter hook prerouting priority raw;
iif { veout, tvrf } meta nftrace set 1
iif veout ct zone set 1 return
iif tvrf ct zone set 2 return
notrack
}
chain rawout {
type filter hook output priority raw;
notrack
}
}
__END__
uname -rv
conntrack -F
ping -W 1 -c 1 -I vein $IPOUT
conntrack -L
Signed-off-by: Eugene Crosser <crosser@average.org>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-16-kuba@kernel.org
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-15-kuba@kernel.org
|
