| Age | Commit message (Collapse) | Author |
|---|
|
The SFP module's eeprom and internals are accessible through an i2c bus.
It is possible that the SFP might be connected to an SMBus-only
controller, such as the one found in some PHY devices in the VSC85xx
family.
Introduce a set of sfp read/write ops that are going to be used if the
i2c bus is only capable of doing smbus byte accesses.
As Single-byte SMBus transaction go against SFF-8472 and breaks the
atomicity for diagnostics data access, hwmon is disabled in the case
of SMBus access.
Moreover, as this may cause other instabilities, print a warning at
probe time to indicate that the setup may be unreliable because of the
hardware design.
As hwmon may be disabled for both broken EEPROM and smbus, the warnings
are udpated accordingly.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322075745.120831-2-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2025-03-24
1) Prevent setting high order sequence number bits input in
non-ESN mode. From Leon Romanovsky.
2) Support PMTU handling in tunnel mode for packet offload.
From Leon Romanovsky.
3) Make xfrm_state_lookup_byaddr lockless.
From Florian Westphal.
4) Remove unnecessary NULL check in xfrm_lookup_with_ifid().
From Dan Carpenter.
* tag 'ipsec-next-2025-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next:
xfrm: Remove unnecessary NULL check in xfrm_lookup_with_ifid()
xfrm: state: make xfrm_state_lookup_byaddr lockless
xfrm: check for PMTU in tunnel mode for packet offload
xfrm: provide common xdo_dev_offload_ok callback implementation
xfrm: rely on XFRM offload
xfrm: simplify SA initialization routine
xfrm: delay initialization of offload path till its actually requested
xfrm: prevent high SEQ input in non-ESN mode
====================
Link: https://patch.msgid.link/20250324061855.4116819-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This fixes the following build warning:
```
drivers/net/ethernet/amd/au1000_eth.c:574:6: warning: no previous prototype for 'au1000_ReleaseDB' [-Wmissing-prototypes]
574 | void au1000_ReleaseDB(struct au1000_private *aup, struct db_dest *pDB)
| ^~~~~~~~~~~~~~~~
```
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250323190450.111241-1-johan.korsnes@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When delete l3s ipvlan:
ip link del link eth0 ipvlan1 type ipvlan mode l3s
This may cause a null pointer dereference:
Call trace:
ip_rcv_finish+0x48/0xd0
ip_rcv+0x5c/0x100
__netif_receive_skb_one_core+0x64/0xb0
__netif_receive_skb+0x20/0x80
process_backlog+0xb4/0x204
napi_poll+0xe8/0x294
net_rx_action+0xd8/0x22c
__do_softirq+0x12c/0x354
This is because l3mdev_l3_rcv() visit dev->l3mdev_ops after
ipvlan_l3s_unregister() assign the dev->l3mdev_ops to NULL. The process
like this:
(CPU1) | (CPU2)
l3mdev_l3_rcv() |
check dev->priv_flags: |
master = skb->dev; |
|
| ipvlan_l3s_unregister()
| set dev->priv_flags
| dev->l3mdev_ops = NULL;
|
visit master->l3mdev_ops |
To avoid this by do not set dev->l3mdev_ops when unregister l3s ipvlan.
Suggested-by: David Ahern <dsahern@kernel.org>
Fixes: c675e06a98a4 ("ipvlan: decouple l3s mode dependencies from other modes")
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250321090353.1170545-1-wangliang74@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, when the driver was printing hex dumps, the buffer was cast
to an 8 byte long and printed using string formatters. If the buffer
size was not a multiple of 8 then a read buffer overflow was possible.
Therefore, create a new ibmvnic function that loops over a buffer and
calls hex_dump_to_buffer instead.
This patch address KASAN reports like the one below:
ibmvnic 30000003 env3: Login Buffer:
ibmvnic 30000003 env3: 01000000af000000
<...>
ibmvnic 30000003 env3: 2e6d62692e736261
ibmvnic 30000003 env3: 65050003006d6f63
==================================================================
BUG: KASAN: slab-out-of-bounds in ibmvnic_login+0xacc/0xffc [ibmvnic]
Read of size 8 at addr c0000001331a9aa8 by task ip/17681
<...>
Allocated by task 17681:
<...>
ibmvnic_login+0x2f0/0xffc [ibmvnic]
ibmvnic_open+0x148/0x308 [ibmvnic]
__dev_open+0x1ac/0x304
<...>
The buggy address is located 168 bytes inside of
allocated 175-byte region [c0000001331a9a00, c0000001331a9aaf)
<...>
=================================================================
ibmvnic 30000003 env3: 000000000033766e
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250320212951.11142-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
More features for 6.15, major changes:
* cfg80211/mac80211: fix and enable link reconfiguration
* rtw88: support RTL8814AE/RTL8814AU
* mt7996: preparations for MLO
* ath12k: continued work on MLO
* iwlwifi: add new iwlmld sub-driver/op-mode for
some current and future devices
* wfx: wowlan support
* tag 'wireless-next-2025-03-20' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (311 commits)
wifi: mt76: mt7996: fix locking in mt7996_mac_sta_rc_work()
wifi: mt76: mt76x2u: add TP-Link TL-WDN6200 ID to device table
wifi: mt76: mt792x: re-register CHANCTX_STA_CSA only for the mt7921 series
wifi: mt76: mt7996: Update mt7996_tx to MLO support
wifi: mt76: mt7996: rework mt7996_ampdu_action to support MLO
wifi: mt76: mt7996: rework set/get_tsf callabcks to support MLO
wifi: mt76: mt7996: set vif default link_id adding/removing vif links
wifi: mt76: mt7996: rework mt7996_mcu_beacon_inband_discov to support MLO
wifi: mt76: mt7996: rework mt7996_mcu_add_obss_spr to support MLO
wifi: mt76: mt7996: rework mt7996_net_fill_forward_path to support MLO
wifi: mt76: mt7996: rework mt7996_update_mu_group to support MLO
wifi: mt76: mt7996: rework mt7996_mac_sta_poll to support MLO
wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO
wifi: mt76: mt7996: remove mt7996_mac_enable_rtscts()
wifi: mt76: mt7996: rework mt7996_sta_hw_queue_read to support MLO
wifi: mt76: mt7996: rework mt7996_set_hw_key to support MLO
wifi: mt76: mt7996: Add mt7996_sta_link to mt7996_mcu_add_bss_info signature
wifi: mt76: mt7996: rework mt7996_sta_set_4addr and mt7996_sta_set_decap_offload to support MLO
wifi: mt76: mt7996: rework mt7996_rx_get_wcid to support MLO
wifi: mt76: mt7996: Rely on wcid_to_sta in mt7996_mac_add_txs_skb()
...
====================
Link: https://patch.msgid.link/20250320131106.33266-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rockchip RK3528 (and RV1106) has a different integrated PHY compared to
the integrated PHY on RK3228/RK3328. Current powerup/down operation is
not compatible with the integrated PHY found in these newer SoCs.
Add operations to powerup/down the integrated PHY found in RK3528.
Use helpers that can be used by other GMAC variants in the future.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250319214415.3086027-6-jonas@kwiboo.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rockchip RK3528 (and RV1106) has a different integrated PHY compared to
the integrated PHY on RK3228/RK3328. Current powerup/down operation is
not compatible with the integrated PHY found in these newer SoCs.
Add a new integrated_phy_powerdown operation and change the call chain
for integrated_phy_powerup to prepare support for the integrated PHY
found in these newer SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250319214415.3086027-5-jonas@kwiboo.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rockchip RK3528 (and RV1106) has a different integrated PHY compared to
the integrated PHY on RK3228/RK3328. Current powerup/down operation is
not compatible with the integrated PHY found in these SoCs.
Move the rk_gmac_integrated_phy_powerup/down functions to top of the
file to prepare for them to be called directly by a GMAC variant
specific powerup/down operation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250319214415.3086027-4-jonas@kwiboo.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rockchip RK3528 has two Ethernet controllers based on Synopsys DWC
Ethernet QoS IP.
Add initial support for the RK3528 GMAC variant.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://patch.msgid.link/20250319214415.3086027-3-jonas@kwiboo.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Following operations can trigger a warning[1]:
ip netns add ns1
ip netns exec ns1 ip link add bond0 type bond mode balance-rr
ip netns exec ns1 ip link set dev bond0 xdp obj af_xdp_kern.o sec xdp
ip netns exec ns1 ip link set bond0 type bond mode broadcast
ip netns del ns1
When delete the namespace, dev_xdp_uninstall() is called to remove xdp
program on bond dev, and bond_xdp_set() will check the bond mode. If bond
mode is changed after attaching xdp program, the warning may occur.
Some bond modes (broadcast, etc.) do not support native xdp. Set bond mode
with xdp program attached is not good. Add check for xdp program when set
bond mode.
[1]
------------[ cut here ]------------
WARNING: CPU: 0 PID: 11 at net/core/dev.c:9912 unregister_netdevice_many_notify+0x8d9/0x930
Modules linked in:
CPU: 0 UID: 0 PID: 11 Comm: kworker/u4:0 Not tainted 6.14.0-rc4 #107
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
Workqueue: netns cleanup_net
RIP: 0010:unregister_netdevice_many_notify+0x8d9/0x930
Code: 00 00 48 c7 c6 6f e3 a2 82 48 c7 c7 d0 b3 96 82 e8 9c 10 3e ...
RSP: 0018:ffffc90000063d80 EFLAGS: 00000282
RAX: 00000000ffffffa1 RBX: ffff888004959000 RCX: 00000000ffffdfff
RDX: 0000000000000000 RSI: 00000000ffffffea RDI: ffffc90000063b48
RBP: ffffc90000063e28 R08: ffffffff82d39b28 R09: 0000000000009ffb
R10: 0000000000000175 R11: ffffffff82d09b40 R12: ffff8880049598e8
R13: 0000000000000001 R14: dead000000000100 R15: ffffc90000045000
FS: 0000000000000000(0000) GS:ffff888007a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000d406b60 CR3: 000000000483e000 CR4: 00000000000006f0
Call Trace:
<TASK>
? __warn+0x83/0x130
? unregister_netdevice_many_notify+0x8d9/0x930
? report_bug+0x18e/0x1a0
? handle_bug+0x54/0x90
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? unregister_netdevice_many_notify+0x8d9/0x930
? bond_net_exit_batch_rtnl+0x5c/0x90
cleanup_net+0x237/0x3d0
process_one_work+0x163/0x390
worker_thread+0x293/0x3b0
? __pfx_worker_thread+0x10/0x10
kthread+0xec/0x1e0
? __pfx_kthread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2f/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
---[ end trace 0000000000000000 ]---
Fixes: 9e2ee5c7e7c3 ("net, bonding: Add XDP support to the bonding driver")
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Acked-by: Jussi Maki <joamaki@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://patch.msgid.link/20250321044852.1086551-1-wangliang74@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DesignWare core requires the receive clock to be running during
certain operations. Ensure that we block PHY RXC clock-stop during
these operations.
This is a best-efforts change - not everywhere can be covered by this
because of net's core locking, which means we can't access the MDIO
bus to configure the PHY to disable RXC clock-stop in certain areas.
These are marked with FIXME comments.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6p-008Vjz-Qy@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some MACs require the PHY receive clock to be running to complete setup
actions. This may fail if the PHY has negotiated EEE, the MAC supports
receive clock stop, and the link has entered LPI state. Provide a pair
of APIs that MAC drivers can use to temporarily block the PHY disabling
the receive clock.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6k-008Vjt-MZ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As the previous commit addressed DWGMAC resuming with a PHY in
suspended state, there is now no need for socfpga to work around
this. Remove this code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6f-008Vjn-J1@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Synopsys Designware GMAC core databook requires all clocks to be
active in order to complete software reset, which we perform during
resume.
However, IEEE 802.3 allows a PHY to stop its clocks when placed in
low-power mode, which happens when the system is suspended and WoL
is not enabled.
As an attempt to work around this, commit 36d18b5664ef ("net: stmmac:
start phylink instance before stmmac_hw_setup()") started phylink
early, but this has the side effect that the mac_link_up() method may
be called before or during the initialisation of GMAC hardware.
We also have the socfpga glue driver directly calling phy_resume()
also as an attempt to work around this.
In a previous commit, phylink_prepare_resume() has been introduced
to give MAC drivers a way to ensure that the PHY is resumed prior to
their initialisation of their MAC hardware. This commit adds the call,
and moves the phylink_resume() call back to where it should be before
the aforementioned commit.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6a-008Vjh-FG@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the system is suspended, the PHY may be placed in low-power mode
by setting the BMCR 0.11 Power down bit. IEEE 802.3 states that the
behaviour of the PHY in this state is implementation specific, and
the PHY is not required to meet the RX_CLK and TX_CLK requirements.
Essentially, this means that a PHY may stop the clocks that it is
generating while in power down state.
However, MACs exist which require the clocks from the PHY to be running
in order to properly resume. phylink_prepare_resume() provides them
with a way to clear the Power down bit early.
Note, however, that IEEE 802.3 gives PHYs up to 500ms grace before the
transmit and receive clocks meet the requirements after clearing the
power down bit.
Add a resume preparation function, which will ensure that the receive
clock from the PHY is appropriately configured while resuming.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6V-008Vjb-AP@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unlike X2 and EF100, we do not attempt to parse the firmware file to
find an image within it; we simply hand the entire file to the MC,
which is responsible for understanding any container formats we might
use and validating that the firmware file is applicable to this NIC.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/9a72a74002a7819c780b0a18ce9294c9d4e1db12.1742493017.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/bcb7597460a5a99d1dca4ef282f4aa2dd46ae545.1742493017.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unlike Siena, no EF10 board ever had an external PHY, and consequently
MDIO handling isn't even built into the firmware. Since Siena has
been split out into its own driver, the MDIO code can be deleted from
the sfc driver.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/aa689d192ddaef7abe82709316c2be648a7bd66e.1742493017.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
vmxnet3 does not unregister xdp rxq info in the
vmxnet3_reset_work() code path as vmxnet3_rq_destroy()
is not invoked in this code path. So, we get below message with a
backtrace.
Missing unregister, handled but fix driver
WARNING: CPU:48 PID: 500 at net/core/xdp.c:182
__xdp_rxq_info_reg+0x93/0xf0
This patch fixes the problem by moving the unregister
code of XDP from vmxnet3_rq_destroy() to vmxnet3_rq_cleanup().
Fixes: 54f00cce1178 ("vmxnet3: Add XDP support.")
Signed-off-by: Sankararaman Jayaraman <sankararaman.jayaraman@broadcom.com>
Signed-off-by: Ronak Doshi <ronak.doshi@broadcom.com>
Link: https://patch.msgid.link/20250320045522.57892-1-sankararaman.jayaraman@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For CT action with commit argument, it's usually followed by the
forward action, either to the output netdev or next chain. The default
behavior for software is to drop by setting action attribute to
TC_ACT_SHOT instead of TC_ACT_PIPE if it's the last action. But driver
can't handle it, so block the offload for such case.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-6-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In nic mode CT setup where we do hairpin between the two
nics, both nics register to the same flow table (per zone),
and try to offload all rules on it.
Instead, filter the rules that originated from the relevant nic
(so only one side is offloaded for each nic).
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-5-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Align mlx5 driver usage of 'pfnum' with the documentation clarification
introduced in commit bb70b0d48d8e ("devlink: Improve the port attributes
description").
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, mlx5_is_reset_now_capable() checks whether the pci bridge is
accessible only on bridge hot plug capability check. If the pci bridge
is not accessible, reset now will fail regardless of bridge hotplug
capability. Move this check to function mlx5_is_reset_now_capable()
which, in such case, aborts the reset and does so in the request phase
instead of the reset now phase.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As queue affinity is being deprecated and will no longer be supported
in the future, Always check for the presence of the port selection
namespace. When available, leverage it to distribute traffic
across the physical ports via steering, ensuring compatibility with
future NICs.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For simplicity reasons, the driver avoids crossing work queue fragment
boundaries within the same TX WQE (Work-Queue Element). Until today, as
the number of packets in a TX MPWQE (Multi-Packet WQE) descriptor is not
known in advance, the driver pre-prepared contiguous memory for the
largest possible WQE. For this, when getting too close to the fragment
edge, having no room for the largest WQE possible, the driver was
filling the fragment remainder with NOP descriptors, aligning the next
descriptor to the beginning of the next fragment.
Generating and handling these NOPs wastes resources, like: CPU cycles,
work-queue entries fetched to the device, and PCI bandwidth.
In this patch, we replace this NOPs filling mechanism in the TX MPWQE
flow. Instead, we utilize the remaining entries of the fragment with a
TX MPWQE. If this room turns out to be too small, we simply open an
additional descriptor starting at the beginning of the next fragment.
Performance benchmark:
uperf test, single server against 3 clients.
TCP multi-stream, bidir, traffic profile "2x350B read, 1400B write".
Bottleneck is in inbound PCI bandwidth (device POV).
+---------------+------------+------------+--------+
| | Before | After | |
+---------------+------------+------------+--------+
| BW | 117.4 Gbps | 121.1 Gbps | +3.1% |
+---------------+------------+------------+--------+
| tx_packets | 15 M/sec | 15.5 M/sec | +3.3% |
+---------------+------------+------------+--------+
| tx_nops | 3 M/sec | 0 | -100% |
+---------------+------------+------------+--------+
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1742391746-118647-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'ras/edac-misc' into edac-updates
* ras/edac-cxl:
EDAC/device: Fix dev_set_name() format string
EDAC: Update memory repair control interface for memory sparing feature
EDAC: Add a memory repair control feature
EDAC: Add a Error Check Scrub control feature
EDAC: Add scrub control feature
EDAC: Add support for EDAC device features control
* ras/edac-drivers:
EDAC/ie31200: Switch Raptor Lake-S to interrupt mode
EDAC/ie31200: Add Intel Raptor Lake-S SoCs support
EDAC/ie31200: Break up ie31200_probe1()
EDAC/ie31200: Fold the two channel loops into one loop
EDAC/ie31200: Make struct dimm_data contain decoded information
EDAC/ie31200: Make the memory controller resources configurable
EDAC/ie31200: Simplify the pci_device_id table
EDAC/ie31200: Fix the 3rd parameter name of *populate_dimm_info()
EDAC/ie31200: Fix the error path order of ie31200_init()
EDAC/ie31200: Fix the DIMM size mask for several SoCs
EDAC/ie31200: Fix the size of EDAC_MC_LAYER_CHIP_SELECT layer
EDAC/{skx_common,i10nm}: Fix some missing error reports on Emerald Rapids
EDAC/igen6: Fix the flood of invalid error reports
EDAC/ie31200: work around false positive build warning
* ras/edac-misc:
MAINTAINERS: Add a secondary maintainer for bluefield_edac
EDAC/pnd2: Make read-only const array intlv static
EDAC/igen6: Constify struct res_config
EDAC/amd64: Simplify return statement in dct_ecc_enabled()
EDAC: Use string choice helper functions
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-03-18 (ice, idpf)
For ice:
Przemek modifies string declarations to resolve compile issues on gcc 7.5.
Karol adds padding to initial programming of GLTSYN_TIME* registers to
ensure it will occur in the future to prevent hardware issues.
Jesse Brandeburg turns off driver RDMA capability when the corresponding
kernel config is not enabled to aid in preventing resource exhaustion.
Jan adjusts type declaration to properly catch error conditions and
prevent truncation of values. He also adds bounds checking to prevent
overflow in ice_vc_cfg_q_quanta().
Lukasz adds checking and error reporting for invalid values in
ice_vc_cfg_q_bw().
Mateusz adds check for valid size for ice_vc_fdir_parse_raw().
For idpf:
Emil adds check, and handling, on failure to register netdev.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: check error for register_netdev() on init
ice: fix using untrusted value of pkt_len in ice_vc_fdir_parse_raw()
ice: fix input validation for virtchnl BW
ice: validate queue quanta parameters to prevent OOB access
ice: stop truncating queue ids when checking
virtchnl: make proto and filter action count unsigned
ice: fix reservation of resources for RDMA when disabled
ice: ensure periodic output start time is in the future
ice: health.c: fix compilation on gcc 7.5
====================
Link: https://patch.msgid.link/20250318200511.2958251-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in cpsw/cpsw_new
drivers. ti cpsw and cpsw_new drivers set xdp headroom at least to
CPSW_HEADROOM_NA:
CPSW_HEADROOM_NA max(XDP_PACKET_HEADROOM, NET_SKB_PAD) + NET_IP_ALIGN
so the headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-7-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in mana driver.
mana driver sets xdp headroom to XDP_PACKET_HEADROOM so the headroom is
large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-6-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in mediatek driver.
mtk_eth_soc driver sets xdp headroom to XDP_PACKET_HEADROOM so the
headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-5-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in octeontx2 driver.
octeontx2 driver sets xdp headroom to OTX2_HEAD_ROOM
OTX2_HEAD_ROOM OTX2_ALIGN
OTX2_ALIGN 128
so the headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-4-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in netsec driver.
netsec driver sets xdp headroom to NETSEC_RXBUF_HEADROOM:
NETSEC_RXBUF_HEADROOM max(XDP_PACKET_HEADROOM, NET_SKB_PAD) + NET_IP_ALIGN
so the headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-3-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in mvpp2 driver
mvpp2 driver sets xdp headroom to:
MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM
where
MVPP2_MH_SIZE 2
MVPP2_SKB_HEADROOM min(max(XDP_PACKET_HEADROOM, NET_SKB_PAD), 224)
so the headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-2-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in mvneta driver
mvneta sets xdp headroom to:
MVNETA_MH_SIZE + MVNETA_SKB_HEADROOM
where
MVNETA_MH_SIZE 2
MVNETA_SKB_HEADROOM max(NET_SKB_PAD, XDP_PACKET_HEADROOM)
so the headroom is large enough to contain xdp_frame and xdp metadata.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-1-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is an effort to achieve W=1 kernel builds without warnings.
As part of that effort Helge Deller highlighted the following warnings
in the tulip driver when compiling with W=1 and CONFIG_TULIP_MWI=n:
.../tulip_core.c: In function ‘tulip_init_one’:
.../tulip_core.c:1309:22: warning: variable ‘force_csr0’ set but not used
This patch addresses that problem using IS_ENABLED(). This approach has
the added benefit of reducing conditionally compiled code. And thus
increasing compile coverage. E.g. for allmodconfig builds which enable
CONFIG_TULIP_MWI.
Compile tested only.
No run-time effect intended.
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318-tulip-w1-v3-1-a813fadd164d@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core x86 updates from Ingo Molnar:
"x86 CPU features support:
- Generate the <asm/cpufeaturemasks.h> header based on build config
(H. Peter Anvin, Xin Li)
- x86 CPUID parsing updates and fixes (Ahmed S. Darwish)
- Introduce the 'setcpuid=' boot parameter (Brendan Jackman)
- Enable modifying CPU bug flags with '{clear,set}puid=' (Brendan
Jackman)
- Utilize CPU-type for CPU matching (Pawan Gupta)
- Warn about unmet CPU feature dependencies (Sohil Mehta)
- Prepare for new Intel Family numbers (Sohil Mehta)
Percpu code:
- Standardize & reorganize the x86 percpu layout and related cleanups
(Brian Gerst)
- Convert the stackprotector canary to a regular percpu variable
(Brian Gerst)
- Add a percpu subsection for cache hot data (Brian Gerst)
- Unify __pcpu_op{1,2}_N() macros to __pcpu_op_N() (Uros Bizjak)
- Construct __percpu_seg_override from __percpu_seg (Uros Bizjak)
MM:
- Add support for broadcast TLB invalidation using AMD's INVLPGB
instruction (Rik van Riel)
- Rework ROX cache to avoid writable copy (Mike Rapoport)
- PAT: restore large ROX pages after fragmentation (Kirill A.
Shutemov, Mike Rapoport)
- Make memremap(MEMREMAP_WB) map memory as encrypted by default
(Kirill A. Shutemov)
- Robustify page table initialization (Kirill A. Shutemov)
- Fix flush_tlb_range() when used for zapping normal PMDs (Jann Horn)
- Clear _PAGE_DIRTY for kernel mappings when we clear _PAGE_RW
(Matthew Wilcox)
KASLR:
- x86/kaslr: Reduce KASLR entropy on most x86 systems, to support PCI
BAR space beyond the 10TiB region (CONFIG_PCI_P2PDMA=y) (Balbir
Singh)
CPU bugs:
- Implement FineIBT-BHI mitigation (Peter Zijlstra)
- speculation: Simplify and make CALL_NOSPEC consistent (Pawan Gupta)
- speculation: Add a conditional CS prefix to CALL_NOSPEC (Pawan
Gupta)
- RFDS: Exclude P-only parts from the RFDS affected list (Pawan
Gupta)
System calls:
- Break up entry/common.c (Brian Gerst)
- Move sysctls into arch/x86 (Joel Granados)
Intel LAM support updates: (Maciej Wieczor-Retman)
- selftests/lam: Move cpu_has_la57() to use cpuinfo flag
- selftests/lam: Skip test if LAM is disabled
- selftests/lam: Test get_user() LAM pointer handling
AMD SMN access updates:
- Add SMN offsets to exclusive region access (Mario Limonciello)
- Add support for debugfs access to SMN registers (Mario Limonciello)
- Have HSMP use SMN through AMD_NODE (Yazen Ghannam)
Power management updates: (Patryk Wlazlyn)
- Allow calling mwait_play_dead with an arbitrary hint
- ACPI/processor_idle: Add FFH state handling
- intel_idle: Provide the default enter_dead() handler
- Eliminate mwait_play_dead_cpuid_hint()
Build system:
- Raise the minimum GCC version to 8.1 (Brian Gerst)
- Raise the minimum LLVM version to 15.0.0 (Nathan Chancellor)
Kconfig: (Arnd Bergmann)
- Add cmpxchg8b support back to Geode CPUs
- Drop 32-bit "bigsmp" machine support
- Rework CONFIG_GENERIC_CPU compiler flags
- Drop configuration options for early 64-bit CPUs
- Remove CONFIG_HIGHMEM64G support
- Drop CONFIG_SWIOTLB for PAE
- Drop support for CONFIG_HIGHPTE
- Document CONFIG_X86_INTEL_MID as 64-bit-only
- Remove old STA2x11 support
- Only allow CONFIG_EISA for 32-bit
Headers:
- Replace __ASSEMBLY__ with __ASSEMBLER__ in UAPI and non-UAPI
headers (Thomas Huth)
Assembly code & machine code patching:
- x86/alternatives: Simplify alternative_call() interface (Josh
Poimboeuf)
- x86/alternatives: Simplify callthunk patching (Peter Zijlstra)
- KVM: VMX: Use named operands in inline asm (Josh Poimboeuf)
- x86/hyperv: Use named operands in inline asm (Josh Poimboeuf)
- x86/traps: Cleanup and robustify decode_bug() (Peter Zijlstra)
- x86/kexec: Merge x86_32 and x86_64 code using macros from
<asm/asm.h> (Uros Bizjak)
- Use named operands in inline asm (Uros Bizjak)
- Improve performance by using asm_inline() for atomic locking
instructions (Uros Bizjak)
Earlyprintk:
- Harden early_serial (Peter Zijlstra)
NMI handler:
- Add an emergency handler in nmi_desc & use it in
nmi_shootdown_cpus() (Waiman Long)
Miscellaneous fixes and cleanups:
- by Ahmed S. Darwish, Andy Shevchenko, Ard Biesheuvel, Artem
Bityutskiy, Borislav Petkov, Brendan Jackman, Brian Gerst, Dan
Carpenter, Dr. David Alan Gilbert, H. Peter Anvin, Ingo Molnar,
Josh Poimboeuf, Kevin Brodsky, Mike Rapoport, Lukas Bulwahn, Maciej
Wieczor-Retman, Max Grobecker, Patryk Wlazlyn, Pawan Gupta, Peter
Zijlstra, Philip Redkin, Qasim Ijaz, Rik van Riel, Thomas Gleixner,
Thorsten Blum, Tom Lendacky, Tony Luck, Uros Bizjak, Vitaly
Kuznetsov, Xin Li, liuye"
* tag 'x86-core-2025-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (211 commits)
zstd: Increase DYNAMIC_BMI2 GCC version cutoff from 4.8 to 11.0 to work around compiler segfault
x86/asm: Make asm export of __ref_stack_chk_guard unconditional
x86/mm: Only do broadcast flush from reclaim if pages were unmapped
perf/x86/intel, x86/cpu: Replace Pentium 4 model checks with VFM ones
perf/x86/intel, x86/cpu: Simplify Intel PMU initialization
x86/headers: Replace __ASSEMBLY__ with __ASSEMBLER__ in non-UAPI headers
x86/headers: Replace __ASSEMBLY__ with __ASSEMBLER__ in UAPI headers
x86/locking/atomic: Improve performance by using asm_inline() for atomic locking instructions
x86/asm: Use asm_inline() instead of asm() in clwb()
x86/asm: Use CLFLUSHOPT and CLWB mnemonics in <asm/special_insns.h>
x86/hweight: Use asm_inline() instead of asm()
x86/hweight: Use ASM_CALL_CONSTRAINT in inline asm()
x86/hweight: Use named operands in inline asm()
x86/stackprotector/64: Only export __ref_stack_chk_guard on CONFIG_SMP
x86/head/64: Avoid Clang < 17 stack protector in startup code
x86/kexec: Merge x86_32 and x86_64 code using macros from <asm/asm.h>
x86/runtime-const: Add the RUNTIME_CONST_PTR assembly macro
x86/cpu/intel: Limit the non-architectural constant_tsc model checks
x86/mm/pat: Replace Intel x86_model checks with VFM ones
x86/cpu/intel: Fix fast string initialization for extended Families
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool updates from Ingo Molnar:
- The biggest change is the new option to automatically fail the build
on objtool warnings: CONFIG_OBJTOOL_WERROR.
While there are no currently known unfixed false positives left, such
an expansion in the severity of objtool warnings inevitably creates a
risk of build failures, so it's disabled by default and depends on
!COMPILE_TEST, so it shouldn't be enabled on
allyesconfig/allmodconfig builds and won't be forced on people who
just accept build-time defaults in 'make oldconfig'.
While the option is strongly recommended, only people who enable it
explicitly should see it.
(Josh Poimboeuf)
- Disable branch profiling in noinstr code with a broad brush that
includes all of arch/x86/ and kernel/sched/. (Josh Poimboeuf)
- Create backup object files on objtool errors and print exact objtool
arguments to make failure analysis easier (Josh Poimboeuf)
- Improve noreturn handling (Josh Poimboeuf)
- Improve rodata handling (Tiezhu Yang)
- Support jump tables, switch tables and goto tables on LoongArch
(Tiezhu Yang)
- Misc cleanups and fixes (Josh Poimboeuf, David Engraf, Ingo Molnar)
* tag 'objtool-core-2025-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
tracing: Disable branch profiling in noinstr code
objtool: Use O_CREAT with explicit mode mask
objtool: Add CONFIG_OBJTOOL_WERROR
objtool: Create backup on error and print args
objtool: Change "warning:" to "error:" for --Werror
objtool: Add --Werror option
objtool: Add --output option
objtool: Upgrade "Linked object detected" warning to error
objtool: Consolidate option validation
objtool: Remove --unret dependency on --rethunk
objtool: Increase per-function WARN_FUNC() rate limit
objtool: Update documentation
objtool: Improve __noreturn annotation warning
objtool: Fix error handling inconsistencies in check()
x86/traps: Make exc_double_fault() consistently noreturn
LoongArch: Enable jump table for objtool
objtool/LoongArch: Add support for goto table
objtool/LoongArch: Add support for switch table
objtool: Handle PC relative relocation type
objtool: Handle different entry size of rodata
...
|
|
Pull bitmap updates from Yury Norov:
- cpumask_next_wrap() rework (me)
- GENMASK() simplification (I Hsin)
- rust bindings for cpumasks (Viresh and me)
- scattered cleanups (Andy, Tamir, Vincent, Ignacio and Joel)
* tag 'bitmap-for-6.15' of https://github.com/norov/linux: (22 commits)
cpumask: align text in comment
riscv: fix test_and_{set,clear}_bit ordering documentation
treewide: fix typo 'unsigned __init128' -> 'unsigned __int128'
MAINTAINERS: add rust bindings entry for bitmap API
rust: Add cpumask helpers
uapi: Revert "bitops: avoid integer overflow in GENMASK(_ULL)"
cpumask: drop cpumask_next_wrap_old()
PCI: hv: Switch hv_compose_multi_msi_req_get_cpu() to using cpumask_next_wrap()
scsi: lpfc: rework lpfc_next_{online,present}_cpu()
scsi: lpfc: switch lpfc_irq_rebalance() to using cpumask_next_wrap()
s390: switch stop_machine_yield() to using cpumask_next_wrap()
padata: switch padata_find_next() to using cpumask_next_wrap()
cpumask: use cpumask_next_wrap() where appropriate
cpumask: re-introduce cpumask_next{,_and}_wrap()
cpumask: deprecate cpumask_next_wrap()
powerpc/xmon: simplify xmon_batch_next_cpu()
ibmvnic: simplify ibmvnic_set_queue_affinity()
virtio_net: simplify virtnet_set_affinity()
objpool: rework objpool_pop()
cpumask: add for_each_{possible,online}_cpu_wrap
...
|
|
Pull documentation updates from Jonathan Corbet:
"It has been a reasonably busy cycle for docs...
- Significant changes throughout the tree to bring Python code up to
current standards and raise the minimum Python required to 3.9
Much of this is preparatory to replacing the ancient Perl
scripts/kernel-doc horror with a slightly less horrifying Python
implementation, expected for 6.16
- Update the minimum Sphinx required to 3.4.3, allowing us to remove
a bunch of older compatibility code
- Rework and improve the generation of the ABI documentation
(All of the above done by Mauro)
- Lots of translation updates. Alex Shi and Yanteng Si are taking on
responsibility for the Chinese translations going forward; that
work will still get to you via docs-next
- Try to standardize the format for indicating a developer's
affiliation in commit tags
- Clarify the TAB's role in CoC enforcement actions
- Try to spell out the rules for when a commit tag can name another
developer without their explicit permission
Plus lots of other typo fixes and updates"
* tag 'docs-6.15' of git://git.lwn.net/linux: (98 commits)
docs/zh_CN: fix spelling mistake
docs/Chinese: change the disclaimer words
docs/zh_CN: Add snp-tdx-threat-model index Chinese translation
docs: driver-api: firmware: clarify userspace requirements
docs: clarify rules wrt tagging other people
docs: Remove outdated highuid.rst documentation
Documentation: dma-buf: heaps: Add heap name definitions
docs/.../submit-checklist: Use Documentation/admin-guide/abi.rst for cross-ref of README
docs: Correct installation instruction
Documentation: kcsan: fix "Plain Accesses and Data Races" URL in kcsan.rst
Documentation/CoC: Spell out the TAB role in enforcement decisions
Documentation: ocxl.rst: Update consortium site
scripts: get_feat.pl: substitute s390x with s390
scripts/kernel-doc: drop dead code for Wcontents_before_sections
scripts/kernel-doc: don't add not needed new lines
docs: driver-api/infiniband.rst: fix Kerneldoc markup
drivers: firewire: firewire-cdev.h: fix identation on a kernel-doc markup
drivers: media: intel-ipu3.h: fix identation on a kernel-doc markup
include/asm-generic/io.h: fix kerneldoc markup
Docs/arch/arm64: Fix spelling in amu.rst
...
|
|
The health poll mechanism performs periodic checks to detect firmware
errors. One of the checks verifies the function is still enabled on
firmware side, but the function is enabled only after enable_hca command
completed. Start health poll after enable_hca command to avoid a race
between function enabled and first health polling.
Fixes: 9b98d395b85d ("net/mlx5: Start health poll at earlier stage of driver load")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/1742331077-102038-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When LAG creation fails, the driver reloads the RDMA devices. If RDMA
representors are present, they should also be reloaded. This step was
missed in the cited commit.
Fixes: 598fe77df855 ("net/mlx5: Lag, Create shared FDB when in switchdev mode")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/1742331077-102038-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/i915/kernel into drm-next
UAPI Changes:
- Increase I915_PARAM_MMAP_GTT_VERSION version to indicate support for partial mmaps (José Roberto de Souza)
Driver Changes:
Fixes/improvements/new stuff:
- Implement vmap/vunmap GEM object functions (Asbjørn Sloth Tønnesen)
Miscellaneous:
- Various register definition cleanups (Ville Syrjälä)
- Fix typo in a comment [gt/uc] (Yuichiro Tsuji)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tursulin@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Z9IXs5CzHHKScuQn@linux
|
|
sja1105_table_delete_entry()
There are actually 2 problems:
- deleting the last element doesn't require the memmove of elements
[i + 1, end) over it. Actually, element i+1 is out of bounds.
- The memmove itself should move size - i - 1 elements, because the last
element is out of bounds.
The out-of-bounds element still remains out of bounds after being
accessed, so the problem is only that we touch it, not that it becomes
in active use. But I suppose it can lead to issues if the out-of-bounds
element is part of an unmapped page.
Fixes: 6666cebc5e30 ("net: dsa: sja1105: Add support for VLAN operations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is all that we can support timestamping, so we shouldn't accept
anything else. Also see sja1105_hwtstamp_get().
To avoid erroring out in an inconsistent state, operate on copies of
priv->hwts_rx_en and priv->hwts_tx_en, and write them back when nothing
else can fail anymore.
Fixes: a602afd200f5 ("net: dsa: sja1105: Expose PTP timestamping ioctls to userspace")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Port counters with no name (aka
sja1105_port_counters[__SJA1105_COUNTER_UNUSED]) are skipped when
reporting sja1105_get_sset_count(), but are not skipped during
sja1105_get_strings() and sja1105_get_ethtool_stats().
As a consequence, the first reported counter has an empty name and a
bogus value (reads from area 0, aka MAC, from offset 0, bits start:end
0:0). Also, the last counter (N_NOT_REACH on E/T, N_RX_BCAST on P/Q/R/S)
gets pushed out of the statistics counters that get shown.
Skip __SJA1105_COUNTER_UNUSED consistently, so that the bogus counter
with an empty name disappears, and in its place appears a valid counter.
Fixes: 039b167d68a3 ("net: dsa: sja1105: don't use burst SPI reads for port statistics")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"As usual, it's scattered changes all over. Patches touching things
outside of our traditional areas in the tree have been Acked by
maintainers or were trivial changes:
- loadpin: remove unsupported MODULE_COMPRESS_NONE (Arulpandiyan
Vadivel)
- samples/check-exec: Fix script name (Mickaël Salaün)
- yama: remove needless locking in yama_task_prctl() (Oleg Nesterov)
- lib/string_choices: Sort by function name (R Sundar)
- hardening: Allow default HARDENED_USERCOPY to be set at compile
time (Mel Gorman)
- uaccess: Split out compile-time checks into ucopysize.h
- kbuild: clang: Support building UM with SUBARCH=i386
- x86: Enable i386 FORTIFY_SOURCE on Clang 16+
- ubsan/overflow: Rework integer overflow sanitizer option
- Add missing __nonstring annotations for callers of
memtostr*()/strtomem*()
- Add __must_be_noncstr() and have memtostr*()/strtomem*() check for
it
- Introduce __nonstring_array for silencing future GCC 15 warnings"
* tag 'hardening-v6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
compiler_types: Introduce __nonstring_array
hardening: Enable i386 FORTIFY_SOURCE on Clang 16+
x86/build: Remove -ffreestanding on i386 with GCC
ubsan/overflow: Enable ignorelist parsing and add type filter
ubsan/overflow: Enable pattern exclusions
ubsan/overflow: Rework integer overflow sanitizer option to turn on everything
samples/check-exec: Fix script name
yama: don't abuse rcu_read_lock/get_task_struct in yama_task_prctl()
kbuild: clang: Support building UM with SUBARCH=i386
loadpin: remove MODULE_COMPRESS_NONE as it is no longer supported
lib/string_choices: Rearrange functions in sorted order
string.h: Validate memtostr*()/strtomem*() arguments more carefully
compiler.h: Introduce __must_be_noncstr()
nilfs2: Mark on-disk strings as nonstring
uapi: stddef.h: Introduce __kernel_nonstring
x86/tdx: Mark message.bytes as nonstring
string: kunit: Mark nonstring test strings as __nonstring
scsi: qla2xxx: Mark device strings as nonstring
scsi: mpt3sas: Mark device strings as nonstring
scsi: mpi3mr: Mark device strings as nonstring
...
|
|
This is a workaround to mitigate a compiler anomaly.
During LLVM toolchain compilation of this driver on s390x architecture, an
unreasonable __write_overflow_field warning occurs.
Contextually, chunk_index is restricted to 0, 1 or 2. By expanding these
possibilities, the compile warning is suppressed.
Fix follow error with clang-19 when -Werror:
In file included from drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_bloom_filter.c:5:
In file included from ./include/linux/gfp.h:7:
In file included from ./include/linux/mmzone.h:8:
In file included from ./include/linux/spinlock.h:63:
In file included from ./include/linux/lockdep.h:14:
In file included from ./include/linux/smp.h:13:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:13:
In file included from ./include/linux/string.h:392:
./include/linux/fortify-string.h:571:4: error: call to '__write_overflow_field' declared with 'warning' attribute: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
571 | __write_overflow_field(p_size_field, size);
| ^
1 error generated.
According to the testing, we can be fairly certain that this is a clang
compiler bug, impacting only clang-19 and below. Clang versions 20 and
21 do not exhibit this behavior.
Link: https://lore.kernel.org/all/484364B641C901CD+20250311141025.1624528-1-wangyuli@uniontech.com/
Fixes: 7585cacdb978 ("mlxsw: spectrum_acl: Add Bloom filter handling")
Co-developed-by: Zijian Chen <czj2441@163.com>
Signed-off-by: Zijian Chen <czj2441@163.com>
Co-developed-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://patch.msgid.link/A1858F1D36E653E0+20250318103654.708077-1-wangyuli@uniontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When hardware floods packets to bridge ports, but flooding to VXLAN bridge
port fails during encapsulation to one of the remote VTEPs, the packets are
trapped to CPU. In such case, the packets are marked with
skb->offload_fwd_mark, which means that packet was L2-forwarded in
hardware. Software data path repeats flooding, but packets which are
marked with skb->offload_fwd_mark will not be flooded by the bridge to
bridge ports which are in the same hardware domain as the ingress port.
Currently, mlxsw does not add VXLAN bridge ports to the same hardware
domain as physical bridge ports despite the fact that the device is able
to forward packets to and from VXLAN tunnels in hardware. In some scenarios
(as mentioned above) this can result in remote VTEPs receiving duplicate
packets. The packets are first flooded by hardware and after an
encapsulation failure, they are flooded again to all remote VTEPs by
software.
Solve this by adding VXLAN bridge ports to the same hardware domain as
physical bridge ports, so then nbp_switchdev_allowed_egress() will return
false also for VXLAN, and packets will not be sent twice from VXLAN device.
switchdev_bridge_port_offload() should get vxlan_dev not as const, so
some changes are required. Call switchdev API from
mlxsw_sp_bridge_vxlan_{join,leave}() which handle offload configurations.
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Closes: https://lore.kernel.org/all/20250210152246.4ajumdchwhvbarik@skbuf/
Reported-by: Vladyslav Mykhaliuk <vmykhaliuk@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/7279056843140fae3a72c2d204c7886b79d03899.1742224300.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Next patch will call __mlxsw_sp_bridge_vxlan_leave() from
mlxsw_sp_bridge_vxlan_join() as part of error flow, move the function to
be able to call the second one.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/64750a0965536530482318578bada30fac372b8a.1742224300.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
