| Age | Commit message (Collapse) | Author |
|---|
|
The security engine is set for management frames by default for 802.11be
chips, so no need to set it in WoWLAN flow.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-7-pkshih@realtek.com
|
|
The setting during suspend or resume is different between different
generation, so update it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-6-pkshih@realtek.com
|
|
The registers to configure mac function for WoWLAN mode that are different
from different generation, so update them.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-5-pkshih@realtek.com
|
|
The register of control and polling function for TX/RX DMA is different
from different generation, so update them. Also rename polling_dma
function to polling_dma_idle to avoid misunderstanding.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-4-pkshih@realtek.com
|
|
The statue register is for driver to check if WoWLAN mode works or stops
successfully. It is changed for new generation, so update it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-3-pkshih@realtek.com
|
|
The WoWLAN reason register is used for driver to get the wakeup reason
for reporting to cfg80211, and it is different from chips. So put it
into chip information.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-2-pkshih@realtek.com
|
|
The kzalloc() in brcmf_pmksa_v3_op() will return null if the
physical memory has run out. As a result, if we dereference
the null value, the null pointer dereference bug will happen.
Return -ENOMEM from brcmf_pmksa_v3_op() if kzalloc() fails
for pmk_op.
Fixes: a96202acaea4 ("wifi: brcmfmac: cfg80211: Add support for PMKID_V3 operations")
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229103153.18533-1-duoming@zju.edu.cn
|
|
The 2 Bluetooth profiles (Hands free profile & Human interface device)
have high duty transmission, it will affect the traffic of WiFi packet
frequently. And once the WiFi traffic down to B/G mode, it will need
a better success rate to recover the transmission rate. Add new policy
option to solve the above situation.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-9-pkshih@realtek.com
|
|
If Bluetooth is working, it will update their info regularly. And the code
will increase the counters while the info updating. Use this counter to
judge is Bluetooth working or not. Don't need to set Bluetooth power or
gain when it is not working.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-8-pkshih@realtek.com
|
|
Add return value to H2C function, and only record down the value while
H2C command success, this can help us to check the real time status.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-7-pkshih@realtek.com
|
|
Wi-Fi firmware need some driver information to do decision or do some
real-time control. Driver will update these information by H2C command.
The chip 8922a H2C command index is different from before chips/branch,
so need to assign the correct index to let firmware parsing.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-6-pkshih@realtek.com
|
|
Change structure member from bit field to normal variable to
reduce unnecessary translation.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-5-pkshih@realtek.com
|
|
To avoid using bit fields for H2C command, rearrange the structure.
And also patch the corresponding code for the using of this structure.
No logic changes for existing chips.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-4-pkshih@realtek.com
|
|
Under some circumstances, coexistence mechanism want to keep grant BT or
WiFi, such as inquiry and WiFi is connecting, to ensure BT or WiFi can
transmit or receive data in that period.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-3-pkshih@realtek.com
|
|
When hardware grant BT initially but transition to grant WiFi, the PLT
(polluted) bit is set to assist coexistence mechanism to debug if
grant signal is expected.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-2-pkshih@realtek.com
|
|
The code here looks well thought-out, so it seems likely
that the byte-swaps are actually needed, due to SPI bus
and device behaviour. Restore the byte-swapping, in a way
that doesn't result in sparse warnings.
Fixes: 7ceade653429 ("wifi: cw1200: fix __le16 sparse warnings")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240228121156.62f820aa6dfb.Ia63314e4d0ed1ee76f100846d68f0722abf6b793@changeid
|
|
When these failures happen, the warning and call trace is printed which is
excessive. Instead, just print the error but rate limited to prevent warns
to unnecessarily pollute the kernel log buffer and make the serial console
practically unusable.
For example, on an AM625 BeaglePlay board where accessing a SDIO WiFi chip
fails with an -110 (ETIMEDOUT) error:
$ dmesg | grep "sdio write\|read failed (-110)" | wc -l
39
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240228101042.728881-1-javierm@redhat.com
|
|
PCI drivers and USB drivers can both use the same function,
read_efuse_byte(), and they can call it directly.
rtl8192de was the only user.
Tested only with the upcoming rtl8192du driver.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/4e2c968d-f25c-4a40-be97-4fdcbdde69cf@gmail.com
|
|
Commit 5459c0b70467 ("PCI/DPC: Quirk PIO log size for certain Intel Root
Ports") and commit 3b8803494a06 ("PCI/DPC: Quirk PIO log size for Intel Ice
Lake Root Ports") add quirks for Ice, Tiger and Alder Lake Root Ports.
System firmware for Raptor Lake still has the bug, so Linux logs the
warning below on several Raptor Lake systems like Dell Precision 3581 with
Intel Raptor Lake processor (0W18NX) system firmware/BIOS version 1.10.1.
pci 0000:00:07.0: [8086:a76e] type 01 class 0x060400
pci 0000:00:07.0: DPC: RP PIO log size 0 is invalid
pci 0000:00:07.1: [8086:a73f] type 01 class 0x060400
pci 0000:00:07.1: DPC: RP PIO log size 0 is invalid
Apply the quirk for Raptor Lake Root Ports as well.
This also enables the DPC driver to dump the RP PIO Log registers when DPC
is triggered.
Link: https://lore.kernel.org/r/20240305113057.56468-1-pmenzel@molgen.mpg.de
Reported-by: Niels van Aert <nvaert1986@hotmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218560
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Niels van Aert <nvaert1986@hotmail.com>
|
|
There is no need to repeat for-loop twice in the error path in
gpiochip_add_data_with_key(). Deduplicate it. While at it,
rename loop variable to be more specific and avoid ambguity.
It also properly unwinds the SRCU, i.e. in reversed order of allocating.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Linux 6.8-rc7
|
|
A race condition between the .runtime_idle() callback and the .remove()
callback in the rtsx_pcr PCI driver leads to a kernel crash due to an
unhandled page fault [1].
The problem is that rtsx_pci_runtime_idle() is not expected to be running
after pm_runtime_get_sync() has been called, but the latter doesn't really
guarantee that. It only guarantees that the suspend and resume callbacks
will not be running when it returns.
However, if a .runtime_idle() callback is already running when
pm_runtime_get_sync() is called, the latter will notice that the runtime PM
status of the device is RPM_ACTIVE and it will return right away without
waiting for the former to complete. In fact, it cannot wait for
.runtime_idle() to complete because it may be called from that callback (it
arguably does not make much sense to do that, but it is not strictly
prohibited).
Thus in general, whoever is providing a .runtime_idle() callback needs
to protect it from running in parallel with whatever code runs after
pm_runtime_get_sync(). [Note that .runtime_idle() will not start after
pm_runtime_get_sync() has returned, but it may continue running then if it
has started earlier.]
One way to address that race condition is to call pm_runtime_barrier()
after pm_runtime_get_sync() (not before it, because a nonzero value of the
runtime PM usage counter is necessary to prevent runtime PM callbacks from
being invoked) to wait for the .runtime_idle() callback to complete should
it be running at that point. A suitable place for doing that is in
pci_device_remove() which calls pm_runtime_get_sync() before removing the
driver, so it may as well call pm_runtime_barrier() subsequently, which
will prevent the race in question from occurring, not just in the rtsx_pcr
driver, but in any PCI drivers providing .runtime_idle() callbacks.
Link: https://lore.kernel.org/lkml/20240229062201.49500-1-kai.heng.feng@canonical.com/ # [1]
Link: https://lore.kernel.org/r/5761426.DvuYhMxLoT@kreacher
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Ricky Wu <ricky_wu@realtek.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
|
|
Refactoring of the field get conversion introduced a regression in the
legacy Wake On Lan from a magic packet with i219 devices. Rx address
copied not correctly from MAC to PHY with FIELD_GET macro.
Fixes: b9a452545075 ("intel: legacy: field get conversion")
Suggested-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a frame can not be transmitted in XDP_REDIRECT
(e.g. due to a full queue), it is necessary to free
it by calling xdp_return_frame_rx_napi.
However, this is the responsibility of the caller of
the ndo_xdp_xmit (see for example bq_xmit_all in
kernel/bpf/devmap.c) and thus calling it inside
igc_xdp_xmit (which is the ndo_xdp_xmit of the igc
driver) as well will lead to memory corruption.
In fact, bq_xmit_all expects that it can return all
frames after the last successfully transmitted one.
Therefore, break for the first not transmitted frame,
but do not call xdp_return_frame_rx_napi in igc_xdp_xmit.
This is equally implemented in other Intel drivers
such as the igb.
There are two alternatives to this that were rejected:
1. Return num_frames as all the frames would have been
transmitted and release them inside igc_xdp_xmit.
While it might work technically, it is not what
the return value is meant to represent (i.e. the
number of SUCCESSFULLY transmitted packets).
2. Rework kernel/bpf/devmap.c and all drivers to
support non-consecutively dropped packets.
Besides being complex, it likely has a negative
performance impact without a significant gain
since it is anyway unlikely that the next frame
can be transmitted if the previous one was dropped.
The memory corruption can be reproduced with
the following script which leads to a kernel panic
after a few seconds. It basically generates more
traffic than a i225 NIC can transmit and pushes it
via XDP_REDIRECT from a virtual interface to the
physical interface where frames get dropped.
#!/bin/bash
INTERFACE=enp4s0
INTERFACE_IDX=`cat /sys/class/net/$INTERFACE/ifindex`
sudo ip link add dev veth1 type veth peer name veth2
sudo ip link set up $INTERFACE
sudo ip link set up veth1
sudo ip link set up veth2
cat << EOF > redirect.bpf.c
SEC("prog")
int redirect(struct xdp_md *ctx)
{
return bpf_redirect($INTERFACE_IDX, 0);
}
char _license[] SEC("license") = "GPL";
EOF
clang -O2 -g -Wall -target bpf -c redirect.bpf.c -o redirect.bpf.o
sudo ip link set veth2 xdp obj redirect.bpf.o
cat << EOF > pass.bpf.c
SEC("prog")
int pass(struct xdp_md *ctx)
{
return XDP_PASS;
}
char _license[] SEC("license") = "GPL";
EOF
clang -O2 -g -Wall -target bpf -c pass.bpf.c -o pass.bpf.o
sudo ip link set $INTERFACE xdp obj pass.bpf.o
cat << EOF > trafgen.cfg
{
/* Ethernet Header */
0xe8, 0x6a, 0x64, 0x41, 0xbf, 0x46,
0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 1, 1, # IP Src - adapt as needed
10, 0, 1, 2, # IP Dest - adapt as needed
const16(6666), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
EOF
sudo trafgen -i trafgen.cfg -b3000MB -o veth1 --cpp
Fixes: 4ff320361092 ("igc: Add support for XDP_REDIRECT action")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Helper i40e_is_fw_ver_eq() compares incorrectly given firmware version
as it returns true when the major version of running firmware is
greater than the given major version that is wrong and results in
failure during getting of DCB configuration where this helper is used.
Fix the check and return true only if the running FW version is exactly
equals to the given version.
Reproducer:
1. Load i40e driver
2. Check dmesg output
[root@host ~]# modprobe i40e
[root@host ~]# dmesg | grep 'i40e.*DCB'
[ 74.750642] i40e 0000:02:00.0: Query for DCB configuration failed, err -EIO aq_err I40E_AQ_RC_EINVAL
[ 74.759770] i40e 0000:02:00.0: DCB init failed -5, disabled
[ 74.966550] i40e 0000:02:00.1: Query for DCB configuration failed, err -EIO aq_err I40E_AQ_RC_EINVAL
[ 74.975683] i40e 0000:02:00.1: DCB init failed -5, disabled
Fixes: cf488e13221f ("i40e: Add other helpers to check version of running firmware and AQ API")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix an obviously incorrect assignment, created with a typo or cut-n-paste
error.
Fixes: 5995ef88e3a8 ("ice: realloc VSI stats arrays")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The pf->dplls.lock mutex is initialized too late, after its first use.
Move it to the top of ice_dpll_init.
Note that the "err_exit" error path destroys the mutex. And the mutex is
the last thing destroyed in ice_dpll_deinit.
This fixes the following warning with CONFIG_DEBUG_MUTEXES:
ice 0000:10:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.36.0
ice 0000:10:00.0: 252.048 Gb/s available PCIe bandwidth (16.0 GT/s PCIe x16 link)
ice 0000:10:00.0: PTP init successful
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 0 PID: 410 at kernel/locking/mutex.c:587 __mutex_lock+0x773/0xd40
Modules linked in: crct10dif_pclmul crc32_pclmul crc32c_intel polyval_clmulni polyval_generic ice(+) nvme nvme_c>
CPU: 0 PID: 410 Comm: kworker/0:4 Not tainted 6.8.0-rc5+ #3
Hardware name: HPE ProLiant DL110 Gen10 Plus/ProLiant DL110 Gen10 Plus, BIOS U56 10/19/2023
Workqueue: events work_for_cpu_fn
RIP: 0010:__mutex_lock+0x773/0xd40
Code: c0 0f 84 1d f9 ff ff 44 8b 35 0d 9c 69 01 45 85 f6 0f 85 0d f9 ff ff 48 c7 c6 12 a2 a9 85 48 c7 c7 12 f1 a>
RSP: 0018:ff7eb1a3417a7ae0 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: 0000000000000002 RSI: ffffffff85ac2bff RDI: 00000000ffffffff
RBP: ff7eb1a3417a7b80 R08: 0000000000000000 R09: 00000000ffffbfff
R10: ff7eb1a3417a7978 R11: ff32b80f7fd2e568 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: ff32b7f02c50e0d8
FS: 0000000000000000(0000) GS:ff32b80efe800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055b5852cc000 CR3: 000000003c43a004 CR4: 0000000000771ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
? __warn+0x84/0x170
? __mutex_lock+0x773/0xd40
? report_bug+0x1c7/0x1d0
? prb_read_valid+0x1b/0x30
? handle_bug+0x42/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? __mutex_lock+0x773/0xd40
? rcu_is_watching+0x11/0x50
? __kmalloc_node_track_caller+0x346/0x490
? ice_dpll_lock_status_get+0x28/0x50 [ice]
? __pfx_ice_dpll_lock_status_get+0x10/0x10 [ice]
? ice_dpll_lock_status_get+0x28/0x50 [ice]
ice_dpll_lock_status_get+0x28/0x50 [ice]
dpll_device_get_one+0x14f/0x2e0
dpll_device_event_send+0x7d/0x150
dpll_device_register+0x124/0x180
ice_dpll_init_dpll+0x7b/0xd0 [ice]
ice_dpll_init+0x224/0xa40 [ice]
? _dev_info+0x70/0x90
ice_load+0x468/0x690 [ice]
ice_probe+0x75b/0xa10 [ice]
? _raw_spin_unlock_irqrestore+0x4f/0x80
? process_one_work+0x1a3/0x500
local_pci_probe+0x47/0xa0
work_for_cpu_fn+0x17/0x30
process_one_work+0x20d/0x500
worker_thread+0x1df/0x3e0
? __pfx_worker_thread+0x10/0x10
kthread+0x103/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
irq event stamp: 125197
hardirqs last enabled at (125197): [<ffffffff8416409d>] finish_task_switch.isra.0+0x12d/0x3d0
hardirqs last disabled at (125196): [<ffffffff85134044>] __schedule+0xea4/0x19f0
softirqs last enabled at (105334): [<ffffffff84e1e65a>] napi_get_frags_check+0x1a/0x60
softirqs last disabled at (105332): [<ffffffff84e1e65a>] napi_get_frags_check+0x1a/0x60
---[ end trace 0000000000000000 ]---
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The function ice_bridge_setlink() may encounter a NULL pointer dereference
if nlmsg_find_attr() returns NULL and br_spec is dereferenced subsequently
in nla_for_each_nested(). To address this issue, add a check to ensure that
br_spec is not NULL before proceeding with the nested attribute iteration.
Fixes: b1edc14a3fbf ("ice: Implement ice_bridge_getlink and ice_bridge_setlink")
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The E800 series hardware uses the same iAVF driver as older devices,
including the virtchnl negotiation scheme.
This negotiation scheme includes a mechanism to determine what type of RSS
should be supported, including RSS over PF virtchnl messages, RSS over
firmware AdminQ messages, and RSS via direct register access.
The PF driver will always prefer VIRTCHNL_VF_OFFLOAD_RSS_PF if its
supported by the VF driver. However, if an older VF driver is loaded, it
may request only VIRTCHNL_VF_OFFLOAD_RSS_REG or VIRTCHNL_VF_OFFLOAD_RSS_AQ.
The ice driver happily agrees to support these methods. Unfortunately, the
underlying hardware does not support these mechanisms. The E800 series VFs
don't have the appropriate registers for RSS_REG. The mailbox queue used by
VFs for VF to PF communication blocks messages which do not have the
VF-to-PF opcode.
Stop lying to the VF that it could support RSS over AdminQ or registers, as
these interfaces do not work when the hardware is operating on an E800
series device.
In practice this is unlikely to be hit by any normal user. The iAVF driver
has supported RSS over PF virtchnl commands since 2016, and always defaults
to using RSS_PF if possible.
In principle, nothing actually stops the existing VF from attempting to
access the registers or send an AQ command. However a properly coded VF
will check the capability flags and will report a more useful error if it
detects a case where the driver does not support the RSS offloads that it
does.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix softirq's not being handled during napi_schedule() call when
receiving marker packets for queue disable by disabling local bottom
half.
The issue can be seen on ifdown:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
Using ftrace to catch the failing scenario:
ifconfig [003] d.... 22739.830624: softirq_raise: vec=3 [action=NET_RX]
<idle>-0 [003] ..s.. 22739.831357: softirq_entry: vec=3 [action=NET_RX]
No interrupt and CPU is idle.
After the patch when disabling local BH before calling napi_schedule:
ifconfig [003] d.... 22993.928336: softirq_raise: vec=3 [action=NET_RX]
ifconfig [003] ..s1. 22993.928337: softirq_entry: vec=3 [action=NET_RX]
Fixes: c2d548cad150 ("idpf: add TX splitq napi poll support")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
total_fa_cnt is supposed to include cck_fa_cnt and ofdm_fa_cnt, not just
ofdm_fa_cnt.
Fixes: 960361238b86 ("rtw88: 8821c: add false alarm statistics")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f3cb6d17-e4e4-44a7-9c9b-72aed994b5c9@gmail.com
|
|
Tenda U9 V2.0, which contains RTL8811CU, is practically unusable because
of frequent disconnections:
Feb 23 14:46:45 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:46 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:46:52 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:46:54 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:55 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:47:01 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:47:04 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:47:05 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
This is caused by a mistake in the chip initialisation. This version of
the chip requires loading an extra AGC table right after the main one,
but the extra table is being loaded at the wrong time, in
rtw_chip_board_info_setup().
Move the extra AGC table loading to the right place, in
rtw_phy_load_tables().
The rtw_chip_board_info_setup() can only do "software" things, and
rtw_phy_load_tables() can really do IO.
Fixes: 5d6651fe8583 ("rtw88: 8821c: support RFE type2 wifi NIC")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/276c31d8-b9a8-4e54-a3ac-09b74657aff7@gmail.com
|
|
Clear bit 8 of REG_SYS_STATUS1 after MAC power on.
Without this, some RTL8821CU and RTL8811CU cannot connect to any
network:
Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
90:55:de:__:__:__ timed out
The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do
it for all three types of chips.
Tested with RTL8811CU (Tenda U9 V2.0).
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/aeeefad9-27c8-4506-a510-ef9a9a8731a4@gmail.com
|
|
RTL8822CU, RTL8822BU, and RTL8821CU need an extra register write after
reading and writing certain addresses.
Without this, the firmware upload fails approximately more than 50% of
the time.
Tested with RTL8811CU (Tenda U9 V2.0) which is the same as RTL8821CU
but without Bluetooth.
Fixes: a82dfd33d123 ("wifi: rtw88: Add common USB chip support")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f12ed39d-28e8-4b8b-8d22-447bcf295afc@gmail.com
|
|
Add VID/PIDs that are known to be missing for this driver.
Removed /* 8811CU */ and /* 8821CU */ as they are redundant
since the file is specific to those chips.
Removed /* TOTOLINK A650UA v3 */ as the manufacturer. It has a REALTEK
VID so it may not be specific to this adapter.
Verified and tested.
Cc: stable@vger.kernel.org
Signed-off-by: Nick Morrow <morrownr@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/4ume7mjw63u7.XlMUvUuacW2ErhOCdqlLkw2@1EHFQ.trk.elasticemail.com
|
|
On a PC Engines APU our admins are faced with:
$ dmesg | grep -c "gpio-keys-polled gpio-keys-polled: unable to claim gpio 0, err=-517"
261
Such a message always appears when e.g. a new USB device is plugged in.
Suppress this message which considerably clutters the kernel log for
EPROBE_DEFER (i.e. -517).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240305101042.10953-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch intended to fix an well-knonw issue in old drivers where the
endpoint type is taken for granted, which is often triggered by fuzzers.
That was the case for this driver [1], and although the fix seems to be
correct, it uncovered another issue that leads to a regression [2], if
the endpoints of the current interface are checked.
The driver makes use of endpoints that belong to a different interface
rather than the one it binds (it binds to the third interface, but also
accesses an endpoint from a different one). The driver should claim the
interfaces it requires, but that is still not the case.
Given that the regression is more severe than the issue found by
syzkaller, the best approach is reverting the patch that causes the
regression, and trying to fix the underlying problem before checking
the endpoint types again.
Note that reverting this patch will probably trigger the syzkaller bug
at some point.
This reverts commit 2b9c3eb32a699acdd4784d6b93743271b4970899.
Link: https://syzkaller.appspot.com/bug?extid=348331f63b034f89b622 [1]
Link: https://lore.kernel.org/linux-input/87sf161jjc.wl-tiwai@suse.de/ [2]
Fixes: 2b9c3eb32a69 ("Input: bcm5974 - check endpoint type before starting traffic")
Reported-by: Jacopo Radice <jacopo.radice@outlook.com>
Closes: https://bugzilla.suse.com/show_bug.cgi?id=1220030
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240305-revert_bcm5974_ep_check-v3-1-527198cf6499@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Even though the UDL driver converts to RGB565 internally (see
pixel32_to_be16() in udl_transfer.c), it advertises XRGB8888 for
compatibility. Let's add ARGB8888 to that list.
This makes UDL devices work on ChromeOS again after commit
c91acda3a380 ("drm/gem: Check for valid formats"). Prior to that
commit things were "working" because we'd silently treat the ARGB8888
that ChromeOS wanted as XRGB8888.
Fixes: c91acda3a380 ("drm/gem: Check for valid formats")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240227141928.1.I24ac8d51544e4624b7e9d438d95880c4283e611b@changeid
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the fcloop_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the nvmf_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the structures nvme_class, nvme_subsys_class and
nvme_ns_chr_class to be declared at build time placing them into read-only
memory, instead of having to be dynamically allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
On Arrow Lake S systems, MEI is no longer strictly connected to bus 0,
while graphics remain exclusively on bus 0. Adapt the component
matching logic to accommodate this change:
Original behavior: Required both MEI and graphics to be on the same
bus 0.
New behavior: Only enforces graphics to be on bus 0 (integrated),
allowing MEI to reside on any bus.
This ensures compatibility with Arrow Lake S and maintains functionality
for the legacy systems.
Fixes: 1dd924f6885b ("mei: gsc_proxy: add gsc proxy driver")
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240220200020.231192-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For CMA memory allocation, ownership is assigned to DSP to make it
accessible by the PD running on the DSP. With current implementation
HLOS VM is stored in the channel structure during rpmsg_probe and
this VM is passed to qcom_scm call as the source VM.
The qcom_scm call will overwrite the passed source VM with the next
VM which would cause a problem in case the scm call is again needed.
Adding a local copy of source VM whereever scm call is made to avoid
this problem.
Fixes: 0871561055e6 ("misc: fastrpc: Add support for audiopd")
Cc: stable <stable@kernel.org>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240224114247.85953-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/198112757eac0fc004677a4757ce48ae7c7194ab.1708508896.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/705b89c3cd7c0a42ce3f482f202204f5e3377aa2.1708508896.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/4b964bd133f5af11cabd51a4d8ed95025583eb93.1708508896.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/250337c967bdb5019a3c9fe8e0d082cd65400227.1708508896.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/946ebc33a01bf700171257cd219fbe8626bc0c99.1708508896.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/8e7179794ffbcaa4ad3d0db50cc4aa03f377fc8c.1708508896.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/8e14f0b1cea107e613fa0075b3379a9f1e7ef63f.1708508896.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
