| Age | Commit message (Collapse) | Author |
|---|
|
Simplify stats accumulation logic to fix the case where we don't take
previous stat value into account, we should always respect it.
Main netdev stats of our PF (Tx/Rx packets/bytes) were reported orders of
magnitude too big during OpenStack reconfiguration events, possibly other
reconfiguration cases too.
The regression was reported to be between 6.1 and 6.2, so I was almost
certain that on of the two "preserve stats over reset" commits were the
culprit. While reading the code, it was found that in some cases we will
increase the stats by arbitrarily large number (thanks to ignoring "-prev"
part of condition, after zeroing it).
Note that this fixes also the case where we were around limits of u64, but
that was not the regression reported.
Full disclosure: I remember suggesting this particular piece of code to
Ben a few years ago, so blame on me.
Fixes: 2fd5e433cd26 ("ice: Accumulate HW and Netdev statistics over reset")
Reported-by: Nebojsa Stevanovic <nebojsa.stevanovic@gcore.com>
Link: https://lore.kernel.org/intel-wired-lan/VI1PR02MB439744DEDAA7B59B9A2833FE912EA@VI1PR02MB4397.eurprd02.prod.outlook.com
Reported-by: Christian Rohmann <christian.rohmann@inovex.de>
Link: https://lore.kernel.org/intel-wired-lan/f38a6ca4-af05-48b1-a3e6-17ef2054e525@inovex.de
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The E1000_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read E1000_TSIRC into 'tsicr';
2. handle the interrupts present into 'tsirc' and mark them in 'ack';
3. write 'ack' into E1000_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 00c65578b47b ("igb: enable internal PPS for the i210")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The IGC_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read IGC_TSIRC into 'tsicr';
2. handle the interrupts present in 'tsirc' and mark them in 'ack';
3. write 'ack' into IGC_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de> # Intel i225
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Just use the request_queue from the gendisk pointer in the relatively
few places that sill need it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-11-hch@lst.de
|
|
Initial queue limits are now set from ->run. Remove the superfluous
initialization in md_alloc and level_store.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-10-hch@lst.de
|
|
Build the queue limits outside the queue and apply them using
queue_limits_set. To make the code more obvious also split the queue
limits handling into separate helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-9-hch@lst.de
|
|
Build the queue limits outside the queue and apply them using
queue_limits_set. To make the code more obvious also split the queue
limits handling into separate helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-8-hch@lst.de
|
|
Build the queue limits outside the queue and apply them using
queue_limits_set. To make the code more obvious also split the queue
limits handling into a separate helper function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-7-hch@lst.de
|
|
Build the queue limits outside the queue and apply them using
queue_limits_set. To make the code more obvious also split the queue
limits handling into a separate helper function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-6-hch@lst.de
|
|
Add a few helpers that wrap the block queue limits API for use in MD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-5-hch@lst.de
|
|
Add a helper to check for a DM-mapped MD device instead of using
the obfuscated ->gendisk or ->queue NULL checks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-4-hch@lst.de
|
|
Add a small wrapper around blk_add_trace_msg that hides some argument
dereferences and the check for a DM-mapped MD device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-3-hch@lst.de
|
|
Add a helper to trace bio remapping that hides some argument
dereferences and the check for a DM-mapped MD device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed--by: Song Liu <song@kernel.org>
Tested-by: Song Liu <song@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240303140150.5435-2-hch@lst.de
|
|
iommu-dma does not explicitly reference min_align_mask since we already
assume that will be less than or equal to any typical IOVA granule.
We wouldn't realistically expect to see the case where it is larger, and
that would be non-trivial to support, however for the sake of reasoning
(particularly around the interaction with SWIOTLB), let's clearly
enforce the assumption.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/dbb4d2d8e5d1691ac9a6c67e9758904e6c447ba5.1709553942.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
domain_context_clear_one() only handles the context entry teardown in
legacy mode. Remove the scalable mode check in it to avoid dead code.
Remove an unnecessary check in the code as well.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20240305013305.204605-6-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The scalable mode context entry is now setup in the probe_device path,
eliminating the need to configure it in the attach_dev path. Removes the
redundant code from the attach_dev path to avoid dead code.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20240305013305.204605-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
In contrast to legacy mode, the DMA translation table is configured in
the PASID table entry instead of the context entry for scalable mode.
For this reason, it is more appropriate to set up the scalable mode
context entry in the device_probe callback and direct it to the
appropriate PASID table.
The iommu domain attach/detach operations only affect the PASID table
entry. Therefore, there is no need to modify the context entry when
configuring the translation type and page table.
The only exception is the kdump case, where context entry setup is
postponed until the device driver invokes the first DMA interface.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20240305013305.204605-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
In the kdump kernel, the IOMMU operates in deferred_attach mode. In this
mode, info->domain may not yet be assigned by the time the release_device
function is called. It leads to the following crash in the crash kernel:
BUG: kernel NULL pointer dereference, address: 000000000000003c
...
RIP: 0010:do_raw_spin_lock+0xa/0xa0
...
_raw_spin_lock_irqsave+0x1b/0x30
intel_iommu_release_device+0x96/0x170
iommu_deinit_device+0x39/0xf0
__iommu_group_remove_device+0xa0/0xd0
iommu_bus_notifier+0x55/0xb0
notifier_call_chain+0x5a/0xd0
blocking_notifier_call_chain+0x41/0x60
bus_notify+0x34/0x50
device_del+0x269/0x3d0
pci_remove_bus_device+0x77/0x100
p2sb_bar+0xae/0x1d0
...
i801_probe+0x423/0x740
Use the release_domain mechanism to fix it. The scalable mode context
entry which is not part of release domain should be cleared in
release_device().
Fixes: 586081d3f6b1 ("iommu/vt-d: Remove DEFER_DEVICE_DOMAIN_INFO")
Reported-by: Eric Badger <ebadger@purestorage.com>
Closes: https://lore.kernel.org/r/20240113181713.1817855-1-ebadger@purestorage.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20240305013305.204605-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The current device_release callback for individual iommu drivers does the
following:
1) Silent IOMMU DMA translation: It detaches any existing domain from the
device and puts it into a blocking state (some drivers might use the
identity state).
2) Resource release: It releases resources allocated during the
device_probe callback and restores the device to its pre-probe state.
Step 1 is challenging for individual iommu drivers because each must check
if a domain is already attached to the device. Additionally, if a deferred
attach never occurred, the device_release should avoid modifying hardware
configuration regardless of the reason for its call.
To simplify this process, introduce a static release_domain within the
iommu_ops structure. It can be either a blocking or identity domain
depending on the iommu hardware. The iommu core will decide whether to
attach this domain before the device_release callback, eliminating the
need for repetitive code in various drivers.
Consequently, the device_release callback can focus solely on the opposite
operations of device_probe, including releasing all resources allocated
during that callback.
Co-developed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20240305013305.204605-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Because surprise removal could happen anytime, e.g. user could request safe
removal to EP(endpoint device) via sysfs and brings its link down to do
surprise removal cocurrently. such aggressive cases would cause ATS
invalidation request issued to non-existence target device, then deadly
loop to retry that request after ITE fault triggered in interrupt context.
this patch aims to optimize the ITE handling by checking the target device
presence state to avoid retrying the timeout request blindly, thus avoid
hard lockup or system hang.
Devices TLB should only be invalidated when devices are in the
iommu->device_rbtree (probed, not released) and present.
Fixes: 6ba6c3a4cacf ("VT-d: add device IOTLB invalidation support")
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com>
Link: https://lore.kernel.org/r/20240301080727.3529832-4-haifeng.zhao@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
For those endpoint devices connect to system via hotplug capable ports,
users could request a hot reset to the device by flapping device's link
through setting the slot's link control register, as pciehp_ist() DLLSC
interrupt sequence response, pciehp will unload the device driver and
then power it off. thus cause an IOMMU device-TLB invalidation (Intel
VT-d spec, or ATS Invalidation in PCIe spec r6.1) request for non-existence
target device to be sent and deadly loop to retry that request after ITE
fault triggered in interrupt context.
That would cause following continuous hard lockup warning and system hang
[ 4211.433662] pcieport 0000:17:01.0: pciehp: Slot(108): Link Down
[ 4211.433664] pcieport 0000:17:01.0: pciehp: Slot(108): Card not present
[ 4223.822591] NMI watchdog: Watchdog detected hard LOCKUP on cpu 144
[ 4223.822622] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S
OE kernel version xxxx
[ 4223.822623] Hardware name: vendorname xxxx 666-106,
BIOS 01.01.02.03.01 05/15/2023
[ 4223.822623] RIP: 0010:qi_submit_sync+0x2c0/0x490
[ 4223.822624] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b
57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 1
0 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39
[ 4223.822624] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093
[ 4223.822625] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005
[ 4223.822625] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340
[ 4223.822625] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000
[ 4223.822626] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200
[ 4223.822626] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004
[ 4223.822626] FS: 0000000000000000(0000) GS:ffffa237ae400000(0000)
knlGS:0000000000000000
[ 4223.822627] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 4223.822627] CR2: 00007ffe86515d80 CR3: 000002fd3000a001 CR4: 0000000000770ee0
[ 4223.822627] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 4223.822628] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
[ 4223.822628] PKRU: 55555554
[ 4223.822628] Call Trace:
[ 4223.822628] qi_flush_dev_iotlb+0xb1/0xd0
[ 4223.822628] __dmar_remove_one_dev_info+0x224/0x250
[ 4223.822629] dmar_remove_one_dev_info+0x3e/0x50
[ 4223.822629] intel_iommu_release_device+0x1f/0x30
[ 4223.822629] iommu_release_device+0x33/0x60
[ 4223.822629] iommu_bus_notifier+0x7f/0x90
[ 4223.822630] blocking_notifier_call_chain+0x60/0x90
[ 4223.822630] device_del+0x2e5/0x420
[ 4223.822630] pci_remove_bus_device+0x70/0x110
[ 4223.822630] pciehp_unconfigure_device+0x7c/0x130
[ 4223.822631] pciehp_disable_slot+0x6b/0x100
[ 4223.822631] pciehp_handle_presence_or_link_change+0xd8/0x320
[ 4223.822631] pciehp_ist+0x176/0x180
[ 4223.822631] ? irq_finalize_oneshot.part.50+0x110/0x110
[ 4223.822632] irq_thread_fn+0x19/0x50
[ 4223.822632] irq_thread+0x104/0x190
[ 4223.822632] ? irq_forced_thread_fn+0x90/0x90
[ 4223.822632] ? irq_thread_check_affinity+0xe0/0xe0
[ 4223.822633] kthread+0x114/0x130
[ 4223.822633] ? __kthread_cancel_work+0x40/0x40
[ 4223.822633] ret_from_fork+0x1f/0x30
[ 4223.822633] Kernel panic - not syncing: Hard LOCKUP
[ 4223.822634] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S
OE kernel version xxxx
[ 4223.822634] Hardware name: vendorname xxxx 666-106,
BIOS 01.01.02.03.01 05/15/2023
[ 4223.822634] Call Trace:
[ 4223.822634] <NMI>
[ 4223.822635] dump_stack+0x6d/0x88
[ 4223.822635] panic+0x101/0x2d0
[ 4223.822635] ? ret_from_fork+0x11/0x30
[ 4223.822635] nmi_panic.cold.14+0xc/0xc
[ 4223.822636] watchdog_overflow_callback.cold.8+0x6d/0x81
[ 4223.822636] __perf_event_overflow+0x4f/0xf0
[ 4223.822636] handle_pmi_common+0x1ef/0x290
[ 4223.822636] ? __set_pte_vaddr+0x28/0x40
[ 4223.822637] ? flush_tlb_one_kernel+0xa/0x20
[ 4223.822637] ? __native_set_fixmap+0x24/0x30
[ 4223.822637] ? ghes_copy_tofrom_phys+0x70/0x100
[ 4223.822637] ? __ghes_peek_estatus.isra.16+0x49/0xa0
[ 4223.822637] intel_pmu_handle_irq+0xba/0x2b0
[ 4223.822638] perf_event_nmi_handler+0x24/0x40
[ 4223.822638] nmi_handle+0x4d/0xf0
[ 4223.822638] default_do_nmi+0x49/0x100
[ 4223.822638] exc_nmi+0x134/0x180
[ 4223.822639] end_repeat_nmi+0x16/0x67
[ 4223.822639] RIP: 0010:qi_submit_sync+0x2c0/0x490
[ 4223.822639] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b
57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 10
74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39
[ 4223.822640] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093
[ 4223.822640] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005
[ 4223.822640] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340
[ 4223.822641] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000
[ 4223.822641] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200
[ 4223.822641] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004
[ 4223.822641] ? qi_submit_sync+0x2c0/0x490
[ 4223.822642] ? qi_submit_sync+0x2c0/0x490
[ 4223.822642] </NMI>
[ 4223.822642] qi_flush_dev_iotlb+0xb1/0xd0
[ 4223.822642] __dmar_remove_one_dev_info+0x224/0x250
[ 4223.822643] dmar_remove_one_dev_info+0x3e/0x50
[ 4223.822643] intel_iommu_release_device+0x1f/0x30
[ 4223.822643] iommu_release_device+0x33/0x60
[ 4223.822643] iommu_bus_notifier+0x7f/0x90
[ 4223.822644] blocking_notifier_call_chain+0x60/0x90
[ 4223.822644] device_del+0x2e5/0x420
[ 4223.822644] pci_remove_bus_device+0x70/0x110
[ 4223.822644] pciehp_unconfigure_device+0x7c/0x130
[ 4223.822644] pciehp_disable_slot+0x6b/0x100
[ 4223.822645] pciehp_handle_presence_or_link_change+0xd8/0x320
[ 4223.822645] pciehp_ist+0x176/0x180
[ 4223.822645] ? irq_finalize_oneshot.part.50+0x110/0x110
[ 4223.822645] irq_thread_fn+0x19/0x50
[ 4223.822646] irq_thread+0x104/0x190
[ 4223.822646] ? irq_forced_thread_fn+0x90/0x90
[ 4223.822646] ? irq_thread_check_affinity+0xe0/0xe0
[ 4223.822646] kthread+0x114/0x130
[ 4223.822647] ? __kthread_cancel_work+0x40/0x40
[ 4223.822647] ret_from_fork+0x1f/0x30
[ 4223.822647] Kernel Offset: 0x6400000 from 0xffffffff81000000 (relocation
range: 0xffffffff80000000-0xffffffffbfffffff)
Such issue could be triggered by all kinds of regular surprise removal
hotplug operation. like:
1. pull EP(endpoint device) out directly.
2. turn off EP's power.
3. bring the link down.
etc.
this patch aims to work for regular safe removal and surprise removal
unplug. these hot unplug handling process could be optimized for fix the
ATS Invalidation hang issue by calling pci_dev_is_disconnected() in
function devtlb_invalidation_with_pasid() to check target device state to
avoid sending meaningless ATS Invalidation request to iommu when device is
gone. (see IMPLEMENTATION NOTE in PCIe spec r6.1 section 10.3.1)
For safe removal, device wouldn't be removed until the whole software
handling process is done, it wouldn't trigger the hard lock up issue
caused by too long ATS Invalidation timeout wait. In safe removal path,
device state isn't set to pci_channel_io_perm_failure in
pciehp_unconfigure_device() by checking 'presence' parameter, calling
pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will return
false there, wouldn't break the function.
For surprise removal, device state is set to pci_channel_io_perm_failure in
pciehp_unconfigure_device(), means device is already gone (disconnected)
call pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will
return true to break the function not to send ATS Invalidation request to
the disconnected device blindly, thus avoid to trigger further ITE fault,
and ITE fault will block all invalidation request to be handled.
furthermore retry the timeout request could trigger hard lockup.
safe removal (present) & surprise removal (not present)
pciehp_ist()
pciehp_handle_presence_or_link_change()
pciehp_disable_slot()
remove_board()
pciehp_unconfigure_device(presence) {
if (!presence)
pci_walk_bus(parent, pci_dev_set_disconnected, NULL);
}
this patch works for regular safe removal and surprise removal of ATS
capable endpoint on PCIe switch downstream ports.
Fixes: 6f7db75e1c46 ("iommu/vt-d: Add second level page table interface")
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Tested-by: Haorong Ye <yehaorong@bytedance.com>
Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com>
Link: https://lore.kernel.org/r/20240301080727.3529832-3-haifeng.zhao@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Make pci_dev_is_disconnected() public so that it can be called from
Intel VT-d driver to quickly fix/workaround the surprise removal
unplug hang issue for those ATS capable devices on PCIe switch downstream
hotplug capable ports.
Beside pci_device_is_present() function, this one has no config space
space access, so is light enough to optimize the normal pure surprise
removal and safe removal flow.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Tested-by: Haorong Ye <yehaorong@bytedance.com>
Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com>
Link: https://lore.kernel.org/r/20240301080727.3529832-2-haifeng.zhao@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These should be the final fixes for the soc tree for 6.8, as usual
they mostly deal wtih dts files:
- Qualcomm fixes for pcie4 on sc8280xp, a revert of msm8996 mpm
support, sm6115 interconnect and sm8650 gpio.
- Two fixes for Tegra234 ethernet
- A Makefile fix to actually build the allwinner based orange pi zero
2w device tree
- Fixes for clocks and reset on imx8mp and a DSI display regression
on imx7.
The non-DT fixes are:
- Firmware fixes addressing a kernel panic in op-tee and a minor
regression in microchip/riscv.
- A defconfig change to bring back backlight support after a Kconfig
change"
* tag 'arm-fixes-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
firmware: microchip: Fix over-requested allocation size
tee: optee: Fix kernel panic caused by incorrect error handling
Revert "arm64: dts: qcom: msm8996: Hook up MPM"
arm64: dts: qcom: sc8280xp-x13s: limit pcie4 link speed
arm64: dts: qcom: sc8280xp-crd: limit pcie4 link speed
arm64: dts: imx8mp: Fix LDB clocks property
arm64: dts: imx8mp: Fix TC9595 reset GPIO on DH i.MX8M Plus DHCOM SoM
MAINTAINERS: Use a proper mailinglist for NXP i.MX development
ARM: dts: imx7: remove DSI port endpoints
arm64: dts: allwinner: h616: Add Orange Pi Zero 2W to Makefile
ARM: imx_v6_v7_defconfig: Restore CONFIG_BACKLIGHT_CLASS_DEVICE
arm64: tegra: Fix Tegra234 MGBE power-domains
arm64: tegra: Set the correct PHY mode for MGBE
arm64: dts: qcom: sm6115: Fix missing interconnect-names
arm64: dts: qcom: sm8650-mtp: add gpio74 as reserved gpio
arm64: dts: qcom: sm8650-qrd: add gpio74 as reserved gpio
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"Fix potential use-after-frees in rk3288 and sun8i-ce"
* tag 'v6.8-p6' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: rk3288 - Fix use after free in unprepare
crypto: sun8i-ce - Fix use after free in unprepare
|
|
bcache currently calculates the stripe size for the non-cached_dev
case directly in bcache_device_init, but for the cached_dev case it does
it in the caller. Consolidate it in one places, which also enables
setting the io_opt queue_limit before allocating the gendisk so that it
can be passed in instead of changing the limit just after the allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20240226104826.283067-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In virtblk_read_zoned_limits(), setting a zoned block device maximum
number of open and active zones using the functions
disk_set_max_open_zones() and disk_set_max_active_zones() is incorrect
as setting the limits for the request queue is now done atomically when
the gendisk is created (with blk_mq_alloc_disk()). The value set by the
disk_set_max_open/active_zones() functions will be overwritten.
Fix this by setting the maximum number of open and active zones directly
in the queue_limits structure passed to virtblk_read_zoned_limits().
Fixes: 8b837256560c ("virtio_blk: pass queue_limits to blk_mq_alloc_disk")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20240301192639.410183-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch is against CVE-2023-6270. The description of cve is:
A flaw was found in the ATA over Ethernet (AoE) driver in the Linux
kernel. The aoecmd_cfg_pkts() function improperly updates the refcnt on
`struct net_device`, and a use-after-free can be triggered by racing
between the free on the struct and the access through the `skbtxq`
global queue. This could lead to a denial of service condition or
potential code execution.
In aoecmd_cfg_pkts(), it always calls dev_put(ifp) when skb initial
code is finished. But the net_device ifp will still be used in
later tx()->dev_queue_xmit() in kthread. Which means that the
dev_put(ifp) should NOT be called in the success path of skb
initial code in aoecmd_cfg_pkts(). Otherwise tx() may run into
use-after-free because the net_device is freed.
This patch removed the dev_put(ifp) in the success path in
aoecmd_cfg_pkts(), and added dev_put() after skb xmit in tx().
Link: https://nvd.nist.gov/vuln/detail/CVE-2023-6270
Fixes: 7562f876cd93 ("[NET]: Rework dev_base via list_head (v3)")
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Link: https://lore.kernel.org/r/20240305082048.25526-1-jlee@suse.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, all Kconfig symbols for R-Car Gen4 SoCs select
ARCH_RCAR_GEN3, which might confuse the casual reader. Prepare for the
advent of ARCH_RCAR_GEN4 by extending the dependency for auto-selecting
reset controller support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
This adds i2c bus recovery to the lpi2c driver.
Uses the generic recovery function setting the SCL/SDA pads as
GPIO pins and sending 9 clocks to try and recover the bus.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Switch drbd_reconsider_queue_parameters to set up the queue parameters
in an on-stack queue_limits structure and apply the atomically. Remove
various helpers that have become so trivial that they can be folded into
drbd_reconsider_queue_parameters.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240305134041.137006-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a helper to check if discard is supported for a given connection /
backing device combination.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20240306140332.623759-7-philipp.reisner@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
fixup_write_zeroes always overrides the max_write_zeroes_sectors value
a little further down the callchain, so don't bother to setup a limit
in decide_on_discard_support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20240306140332.623759-6-philipp.reisner@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
drbd_setup_queue_param is only called by drbd_reconsider_queue_parameters
and there is no really clear boundary of responsibilities between the
two.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20240306140332.623759-5-philipp.reisner@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Factor out a drbd_backing_dev_max_segments helper that checks the
backing device limitation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20240306140332.623759-4-philipp.reisner@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Split out a drbd_max_peer_bio_size helper for the peer I/O size,
and condense the various checks to a nested min3(..., max())) instead
of using a lot of local variables.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240305134041.137006-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pass a queue_limits structure with the max_hw_sectors limit to
blk_alloc_disk instead of updating the limit on the allocated gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240305134041.137006-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the block_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240305-class_cleanup-block-v1-1-130bb27b9c72@marliere.net
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/song/md into for-6.9/block
Pull MD fixes from Song:
"This set fixes two issues:
1. dmraid regression since 6.7 kernels. This issue was initially
reported in [1]. This set of fix has been reviewed and tested by
md and dm folks.
2. raid5 hang since 6.7 kernel, reported in [2]. We haven't got a
better fix for this issue yet. This revert is a workaround. It has
been applied to 6.7 stable kernels [3], and proved to be affective.
We will look more into this issue for a better fix.
[1] https://lore.kernel.org/linux-raid/e5e8afe2-e9a8-49a2-5ab0-958d4065c55e@redhat.com/
[2] https://lore.kernel.org/linux-raid/20240123005700.9302-1-dan@danm.net/
[3] 87165c64fe1a in linux-6.7.y branch."
* tag 'md-6.9-20240305' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
dm-raid: fix lockdep waring in "pers->hot_add_disk"
dm-raid456, md/raid456: fix a deadlock for dm-raid456 while io concurrent with reshape
dm-raid: add a new helper prepare_suspend() in md_personality
md/dm-raid: don't call md_reap_sync_thread() directly
dm-raid: really frozen sync_thread during suspend
md: add a new helper reshape_interrupted()
md: export helper md_is_rdwr()
md: export helpers to stop sync_thread
md: don't clear MD_RECOVERY_FROZEN for new dm-raid until resume
Revert "Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d""
|
|
Pass the constant limits directly to blk_mq_alloc_disk, set the nonrot
flag there as well, and then use the commit API to change the transfer
size and logical block size dependent values.
This relies on the assumption that no I/O can be pending before the
devices moves into the ready state and doesn't need extra freezing
for changes to the queue limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20240228133742.806274-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Most of the code in setup_blk_queue is shared between all disciplines.
Move it to common code and leave a method to query the maximum number
of transferable blocks, and a flag to indicate discard support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20240228133742.806274-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Reflow dasd_state_basic_to_ready a bit to make it easier to modify.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20240228133742.806274-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 95bf25bb9ed5dedb7fb39f76489f7d6843ab0475.
Apparently there was a previous discussion about emulation of formats
and it was decided XRGB8888 was the only format to support for legacy
userspace [1]. Remove ARGB8888. Userspace needs to be fixed to accept
XRGB8888.
[1] https://lore.kernel.org/r/60dc7697-d7a0-4bf4-a22e-32f1bbb792c2@suse.de
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306063721.1.I4a32475190334e1fa4eef4700ecd2787a43c94b5@changeid
|
|
Due to a long-standing issue in driver core, drivers may not probe defer
after having registered child devices to avoid triggering a probe
deferral loop (see fbc35b45f9f6 ("Add documentation on meaning of
-EPROBE_DEFER")).
Move registration of the typec switch to after looking up clocks and
other resources.
Note that PHY creation can in theory also trigger a probe deferral when
a 'phy' supply is used. This does not seem to affect the QMP PHY driver
but the PHY subsystem should be reworked to address this (i.e. by
separating initialisation and registration of the PHY).
Fixes: 2851117f8f42 ("phy: qcom-qmp-combo: Introduce orientation switching")
Cc: stable@vger.kernel.org # 6.5
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240217150228.5788-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Due to a long-standing issue in driver core, drivers may not probe defer
after having registered child devices to avoid triggering a probe
deferral loop (see fbc35b45f9f6 ("Add documentation on meaning of
-EPROBE_DEFER")).
This could potentially also trigger a bug in the DRM bridge
implementation which does not expect bridges to go away even if device
links may avoid triggering this (when enabled).
Move registration of the DRM aux bridge to after looking up clocks and
other resources.
Note that PHY creation can in theory also trigger a probe deferral when
a 'phy' supply is used. This does not seem to affect the QMP PHY driver
but the PHY subsystem should be reworked to address this (i.e. by
separating initialisation and registration of the PHY).
Fixes: 35921910bbd0 ("phy: qcom: qmp-combo: switch to DRM_AUX_BRIDGE")
Fixes: 1904c3f578dc ("phy: qcom-qmp-combo: Introduce drm_bridge")
Cc: stable@vger.kernel.org # 6.5
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240217150228.5788-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The memory allocated for the identification is freed on failure. Set
it to NULL so the caller doesn't have a pointer to that freed address.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
greybus_hd_type, greybus_module_type, greybus_interface_type,
greybus_control_type, greybus_bundle_type and greybus_svc_type variables to
be constant structures as well, placing it into read-only memory which can
not be modified at runtime.
Signed-off-by: "Ricardo B. Marliere" <ricardo@marliere.net>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240219-device_cleanup-greybus-v1-1-babb3f65e8cc@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that the driver core can properly handle constant struct bus_type,
move the greybus_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Alex Elder <elder@kernel.org>
Cc: greybus-dev@lists.linaro.org
Reviewed-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/2024010517-handgun-scoreless-05e7@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"gpio2" as intended here, not "gpio1".
Fixes: 95daa868f22b ("regulator: lp8788-buck: Fully convert to GPIO descriptors")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://msgid.link/r/19f62cc2-bdcf-46f7-a5c5-971ef05e1ea7@moroto.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 6.9
This pull request contains the interconnect changes for the 6.9-rc1 merge
window. The highlights are below:
Core changes:
- Constify the of_phandle_args in xlate functions.
Driver changes:
- New interconnect driver for the MSM8909 platform.
- New interconnect driver for the SM7150 platform.
- Clean-up and removal of unused resources in drivers.
- Constify some pointers to structs.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: Add SM7150 driver support
dt-bindings: interconnect: Add Qualcomm SM7150 DT bindings
interconnect: constify of_phandle_args in xlate
dt-bindings: interconnect: qcom,rpmh: Fix bouncing @codeaurora address
interconnect: qcom: x1e80100: constify pointer to qcom_icc_bcm
interconnect: qcom: sa8775p: constify pointer to qcom_icc_bcm
interconnect: qcom: sm6115: constify pointer to qcom_icc_node
interconnect: qcom: sm8250: constify pointer to qcom_icc_node
interconnect: qcom: sa8775p: constify pointer to qcom_icc_node
interconnect: qcom: msm8909: constify pointer to qcom_icc_node
interconnect: qcom: x1e80100: Remove bogus per-RSC BCMs and nodes
dt-bindings: interconnect: Remove bogus interconnect nodes
interconnect: qcom: sm8550: Remove bogus per-RSC BCMs and nodes
interconnect: qcom: Add MSM8909 interconnect provider driver
dt-bindings: interconnect: Add Qualcomm MSM8909 DT bindings
|
|
When nvme_identify_ns() fails, it frees the pointer to the struct
nvme_id_ns before it returns. However, ns_update_nuse() calls kfree()
for the pointer even when nvme_identify_ns() fails. This results in
KASAN double-free, which was observed with blktests nvme/045 with
proposed patches [1] on the kernel v6.8-rc7. Fix the double-free by
skipping kfree() when nvme_identify_ns() fails.
Link: https://lore.kernel.org/linux-block/20240304161303.19681-1-dwagner@suse.de/ [1]
Fixes: a1a825ab6a60 ("nvme: add csi, ms and nuse to sysfs")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
