| Age | Commit message (Collapse) | Author |
|---|
|
So far changing the period by just setting new period values while
running did not work.
The order as indicated by the publicly available reference manual of the i.MX8MP [1]
indicates a sequence:
* initiate the programming sequence
* set the values for PPS period and start time
* start the pulse train generation.
This is currently not used in dwmac5_flex_pps_config(), which instead does:
* initiate the programming sequence and immediately start the pulse train generation
* set the values for PPS period and start time
This caused the period values written not to take effect until the FlexPPS output was
disabled and re-enabled again.
This patch fix the order and allows the period to be set immediately.
[1] https://www.nxp.com/webapp/Download?colCode=IMX8MPRM
Fixes: 9a8a02c9d46d ("net: stmmac: Add Flexible PPS support")
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230210143937.3427483-1-j.zink@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In bnxt_reserve_rings(), there is logic to check that the number of TX
rings reserved is enough to cover all the mqprio TCs, but it fails to
account for the TX XDP rings. So the check will always fail if there
are mqprio TCs and TX XDP rings. As a result, the driver always fails
to initialize after the XDP program is attached and the device will be
brought down. A subsequent ifconfig up will also fail because the
number of TX rings is set to an inconsistent number. Fix the check to
properly account for TX XDP rings. If the check fails, set the number
of TX rings back to a consistent number after calling netdev_reset_tc().
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported that act_len in kalmia_send_init_packet() is
uninitialized when passing it to the first usb_bulk_msg error path. Jiri
Pirko noted that it's pointless to pass it in the error path, and that
the value that would be printed in the second error path would be the
value of act_len from the first call to usb_bulk_msg.[1]
With this in mind, let's just not pass act_len to the usb_bulk_msg error
paths.
1: https://lore.kernel.org/lkml/Y9pY61y1nwTuzMOa@nanopsycho/
Fixes: d40261236e8e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Reported-and-tested-by: syzbot+cd80c5ef5121bfe85b55@syzkaller.appspotmail.com
Signed-off-by: Miko Larsson <mikoxyzzz@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The result of nlmsg_find_attr() 'br_spec' is dereferenced in
nla_for_each_nested(), but it can take NULL value in nla_find() function,
which will result in an error.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 51616018dd1b ("i40e: Add support for getlink, setlink ndo ops")
Signed-off-by: Natalia Petrova <n.petrova@fintech.ru>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230209172833.3596034-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Incrementation of xsk_frames inside the for-loop produces
infinite loop, if we have both normal AF_XDP-TX and XDP_TXed
buffers to complete.
Split xsk_frames into 2 variables (xsk_frames and completed_frames)
to eliminate this bug.
Fixes: 29322791bc8b ("ice: xsk: change batched Tx descriptor cleaning")
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230209160130.1779890-1-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In TI's AM62x/AM64x SoCs, successful teardown of RX DMA Channel raises an
interrupt. The process of servicing this interrupt involves flushing all
pending RX DMA descriptors and clearing the teardown completion marker
(TDCM). The am65_cpsw_nuss_rx_packets() function invoked from the RX
NAPI callback services the interrupt. Thus, it is necessary to wait for
this handler to run, drain all packets and clear TDCM, before calling
napi_disable() in am65_cpsw_nuss_common_stop() function post channel
teardown. If napi_disable() executes before ensuring that TDCM is
cleared, the TDCM remains set when the interfaces are down, resulting in
an interrupt storm when the interfaces are brought up again.
Since the interrupt raised to indicate the RX DMA Channel teardown is
specific to the AM62x and AM64x SoCs, add a quirk for it.
Fixes: 4f7cce272403 ("net: ethernet: ti: am65-cpsw: add support for am64x cpsw3g")
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230209084432.189222-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit b3973bb40041 ("vmxnet3: set correct hash type based on
rss information") added hashType information into skb. However,
rssType field is populated for eop descriptor. This can lead
to incorrectly reporting of hashType for packets which use
multiple rx descriptors. Multiple rx descriptors are used
for Jumbo frame or LRO packets, which can hit this issue.
This patch moves the RSS codeblock under eop descritor.
Cc: stable@vger.kernel.org
Fixes: b3973bb40041 ("vmxnet3: set correct hash type based on rss information")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Peng Li <lpeng@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Link: https://lore.kernel.org/r/20230208223900.5794-1-doshir@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPsec offloading callbacks may be called in atomic context, sleep is
not allowed in the implementation. Now use workqueue mechanism to
avoid this issue.
Extend existing workqueue mechanism for multicast configuration only
to universal use, so that all configuring through mailbox asynchronously
can utilize it.
Fixes: 859a497fe80c ("nfp: implement xfrm callbacks and expose ipsec offload feature to upper layer")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mailbox configuration mechanism requires writing several registers,
which shouldn't be interrupted, so need lock to avoid race condition.
The base offset of mailbox configuration registers is not fixed, it
depends on TLV caps read from application firmware.
Fixes: 859a497fe80c ("nfp: implement xfrm callbacks and expose ipsec offload feature to upper layer")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Code blocks handling BCMA_CHIP_ID_BCM5357 and BCMA_CHIP_ID_BCM53572 were
incorrectly unified. Chip package values are not unique and cannot be
checked independently. They are meaningful only in a context of a given
chip.
Packages BCM5358 and BCM47188 share the same value but then belong to
different chips. Code unification resulted in treating BCM5358 as
BCM47188 and broke its initialization.
Link: https://github.com/openwrt/openwrt/issues/8278
Fixes: cb1b0f90acfe ("net: ethernet: bgmac: unify code of the same family")
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230208091637.16291-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can and ipsec subtrees.
Current release - regressions:
- sched: fix off by one in htb_activate_prios()
- eth: mana: fix accessing freed irq affinity_hint
- eth: ice: fix out-of-bounds KASAN warning in virtchnl
Current release - new code bugs:
- eth: mtk_eth_soc: enable special tag when any MAC uses DSA
Previous releases - always broken:
- core: fix sk->sk_txrehash default
- neigh: make sure used and confirmed times are valid
- mptcp: be careful on subflow status propagation on errors
- xfrm: prevent potential spectre v1 gadget in xfrm_xlate32_attr()
- phylink: move phy_device_free() to correctly release phy device
- eth: mlx5:
- fix crash unsetting rx-vlan-filter in switchdev mode
- fix hang on firmware reset
- serialize module cleanup with reload and remove"
* tag 'net-6.2-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits)
selftests: forwarding: lib: quote the sysctl values
net: mscc: ocelot: fix all IPv6 getting trapped to CPU when PTP timestamping is used
rds: rds_rm_zerocopy_callback() use list_first_entry()
net: txgbe: Update support email address
selftests: Fix failing VXLAN VNI filtering test
selftests: mptcp: stop tests earlier
selftests: mptcp: allow more slack for slow test-case
mptcp: be careful on subflow status propagation on errors
mptcp: fix locking for in-kernel listener creation
mptcp: fix locking for setsockopt corner-case
mptcp: do not wait for bare sockets' timeout
net: ethernet: mtk_eth_soc: fix DSA TX tag hwaccel for switch port 0
nfp: ethtool: fix the bug of setting unsupported port speed
txhash: fix sk->sk_txrehash default
net: ethernet: mtk_eth_soc: fix wrong parameters order in __xdp_rxq_info_reg()
net: ethernet: mtk_eth_soc: enable special tag when any MAC uses DSA
net: sched: sch: Fix off by one in htb_activate_prios()
igc: Add ndo_tx_timeout support
net: mana: Fix accessing freed irq affinity_hint
hv_netvsc: Allocate memory in netvsc_dma_map() with GFP_ATOMIC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Benjamin Tissoires:
- fix potential infinite loop with a badly crafted HID device (Xin
Zhao)
- fix regression from 6.1 in USB logitech devices potentially making
their mouse wheel not working (Bastien Nocera)
- clean up in AMD sensors, which fixes a long time resume bug (Mario
Limonciello)
- few device small fixes and quirks
* tag 'for-linus-2023020901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: Ignore battery for ELAN touchscreen 29DF on HP
HID: amd_sfh: if no sensors are enabled, clean up
HID: logitech: Disable hi-res scrolling on USB
HID: core: Fix deadloop in hid_apply_multiplier.
HID: Ignore battery for Elan touchscreen on Asus TP420IA
HID: elecom: add support for TrackBall 056E:011C
|
|
is used
While running this selftest which usually passes:
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
if I start PTP timestamping then run it again (debug prints added by me),
the unknown IPv6 MC traffic is seen by the CPU port even when it should
have been dropped:
~/selftests/drivers/net/dsa# ptp4l -i swp0 -2 -P -m
ptp4l[225.410]: selected /dev/ptp1 as PTP clock
[ 225.445746] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_add: port 0 adding L2 PTP trap
[ 225.453815] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP event trap
[ 225.462703] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP general trap
[ 225.471768] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP event trap
[ 225.480651] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP general trap
ptp4l[225.488]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[225.488]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
^C
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [FAIL]
reception succeeded, but should have failed
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
The PGID_MCIPV6 is configured correctly to not flood to the CPU,
I checked that.
Furthermore, when I disable back PTP RX timestamping (ptp4l doesn't do
that when it exists), packets are RX filtered again as they should be:
~/selftests/drivers/net/dsa# hwstamp_ctl -i swp0 -r 0
[ 218.202854] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_del: port 0 removing L2 PTP trap
[ 218.212656] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP event trap
[ 218.222975] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP general trap
[ 218.233133] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP event trap
[ 218.242251] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP general trap
current settings:
tx_type 1
rx_filter 12
new settings:
tx_type 1
rx_filter 0
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
So it's clear that something in the PTP RX trapping logic went wrong.
Looking a bit at the code, I can see that there are 4 typos, which
populate "ipv4" VCAP IS2 key filter fields for IPv6 keys.
VCAP IS2 keys of type OCELOT_VCAP_KEY_IPV4 and OCELOT_VCAP_KEY_IPV6 are
handled by is2_entry_set(). OCELOT_VCAP_KEY_IPV4 looks at
&filter->key.ipv4, and OCELOT_VCAP_KEY_IPV6 at &filter->key.ipv6.
Simply put, when we populate the wrong key field, &filter->key.ipv6
fields "proto.mask" and "proto.value" remain all zeroes (or "don't care").
So is2_entry_set() will enter the "else" of this "if" condition:
if (msk == 0xff && (val == IPPROTO_TCP || val == IPPROTO_UDP))
and proceed to ignore the "proto" field. The resulting rule will match
on all IPv6 traffic, trapping it to the CPU.
This is the reason why the local_termination.sh selftest sees it,
because control traps are stronger than the PGID_MCIPV6 used for
flooding (from the forwarding data path).
But the problem is in fact much deeper. We trap all IPv6 traffic to the
CPU, but if we're bridged, we set skb->offload_fwd_mark = 1, so software
forwarding will not take place and IPv6 traffic will never reach its
destination.
The fix is simple - correct the typos.
I was intentionally inaccurate in the commit message about the breakage
occurring when any PTP timestamping is enabled. In fact it only happens
when L4 timestamping is requested (HWTSTAMP_FILTER_PTP_V2_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT). But ptp4l requests a larger RX
timestamping filter than it needs for "-2": HWTSTAMP_FILTER_PTP_V2_EVENT.
I wanted people skimming through git logs to not think that the bug
doesn't affect them because they only use ptp4l in L2 mode.
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230207183117.1745754-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2023-02-07
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Serialize module cleanup with reload and remove
net/mlx5: fw_tracer, Zero consumer index when reloading the tracer
net/mlx5: fw_tracer, Clear load bit when freeing string DBs buffers
net/mlx5: Expose SF firmware pages counter
net/mlx5: Store page counters in a single array
net/mlx5e: IPoIB, Show unknown speed instead of error
net/mlx5e: Fix crash unsetting rx-vlan-filter in switchdev mode
net/mlx5: Bridge, fix ageing of peer FDB entries
net/mlx5: DR, Fix potential race in dr_rule_create_rule_nic
net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change
====================
Link: https://lore.kernel.org/r/20230208030302.95378-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Arınç reports that on his MT7621AT Unielec U7621-06 board and MT7623NI
Bananapi BPI-R2, packets received by the CPU over mt7530 switch port 0
(of which this driver acts as the DSA master) are not processed
correctly by software. More precisely, they arrive without a DSA tag
(in packet or in the hwaccel area - skb_metadata_dst()), so DSA cannot
demux them towards the switch's interface for port 0. Traffic from other
ports receives a skb_metadata_dst() with the correct port and is demuxed
properly.
Looking at mtk_poll_rx(), it becomes apparent that this driver uses the
skb vlan hwaccel area:
union {
u32 vlan_all;
struct {
__be16 vlan_proto;
__u16 vlan_tci;
};
};
as a temporary storage for the VLAN hwaccel tag, or the DSA hwaccel tag.
If this is a DSA master it's a DSA hwaccel tag, and finally clears up
the skb VLAN hwaccel header.
I'm guessing that the problem is the (mis)use of API.
skb_vlan_tag_present() looks like this:
#define skb_vlan_tag_present(__skb) (!!(__skb)->vlan_all)
So if both vlan_proto and vlan_tci are zeroes, skb_vlan_tag_present()
returns precisely false. I don't know for sure what is the format of the
DSA hwaccel tag, but I surely know that lowermost 3 bits of vlan_proto
are 0 when receiving from port 0:
unsigned int port = vlan_proto & GENMASK(2, 0);
If the RX descriptor has no other bits set to non-zero values in
RX_DMA_VTAG, then the call to __vlan_hwaccel_put_tag() will not, in
fact, make the subsequent skb_vlan_tag_present() return true, because
it's implemented like this:
static inline void __vlan_hwaccel_put_tag(struct sk_buff *skb,
__be16 vlan_proto, u16 vlan_tci)
{
skb->vlan_proto = vlan_proto;
skb->vlan_tci = vlan_tci;
}
What we need to do to fix this problem (assuming this is the problem) is
to stop using skb->vlan_all as temporary storage for driver affairs, and
just create some local variables that serve the same purpose, but
hopefully better. Instead of calling skb_vlan_tag_present(), let's look
at a boolean has_hwaccel_tag which we set to true when the RX DMA
descriptors have something. Disambiguate based on netdev_uses_dsa()
whether this is a VLAN or DSA hwaccel tag, and only call
__vlan_hwaccel_put_tag() if we're certain it's a VLAN tag.
Arınç confirms that the treatment works, so this validates the
assumption.
Link: https://lore.kernel.org/netdev/704f3a72-fc9e-714a-db54-272e17612637@arinc9.com/
Fixes: 2d7605a72906 ("net: ethernet: mtk_eth_soc: enable hardware DSA untagging")
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unsupported port speed can be set and cause error. Now fixing it
and return an error if setting unsupported speed.
This fix depends on the following, which was included in v6.2-rc1:
commit a61474c41e8c ("nfp: ethtool: support reporting link modes").
Fixes: 7c698737270f ("nfp: add support for .set_link_ksettings()")
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parameters 'queue_index' and 'napi_id' are passed in a swapped order.
Fix it here.
Fixes: 23233e577ef9 ("net: ethernet: mtk_eth_soc: rely on page_pool for single page buffers")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The special tag is only enabled when the first MAC uses DSA. However, it
must be enabled when any MAC uses DSA. Change the check accordingly.
This fixes hardware DSA untagging not working on the second MAC of the
MT7621 and MT7623 SoCs, and likely other SoCs too. Therefore, remove the
check that disables hardware DSA untagging for the second MAC of the MT7621
and MT7623 SoCs.
Fixes: a1f47752fd62 ("net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC")
Co-developed-by: Richard van Schagen <richard@routerhints.com>
Signed-off-by: Richard van Schagen <richard@routerhints.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-02-06 (ice)
This series contains updates to ice driver only.
Ani removes WQ_MEM_RECLAIM flag from workqueue to resolve
check_flush_dependency warning.
Michal fixes KASAN out-of-bounds warning.
Brett corrects behaviour for port VLAN Rx filters to prevent receiving
of unintended traffic.
Dan Carpenter fixes possible off by one issue.
Zhang Changzhong adjusts error path for switch recipe to prevent memory
leak.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: switch: fix potential memleak in ice_add_adv_recipe()
ice: Fix off by one in ice_tc_forward_to_queue()
ice: Fix disabling Rx VLAN filtering with port VLAN enabled
ice: fix out-of-bounds KASAN warning in virtchnl
ice: Do not use WQ_MEM_RECLAIM flag for workqueue
====================
Link: https://lore.kernel.org/r/20230206232934.634298-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On some platforms, 100/1000/2500 speeds seem to have sometimes problems
reporting false positive tx unit hang during stressful UDP traffic. Likely
other Intel drivers introduce responses to a tx hang. Update the 'tx hang'
comparator with the comparison of the head and tail of ring pointers and
restore the tx_timeout_factor to the previous value (one).
This can be test by using netperf or iperf3 applications.
Example:
iperf3 -s -p 5001
iperf3 -c 192.168.0.2 --udp -p 5001 --time 600 -b 0
netserver -p 16604
netperf -H 192.168.0.2 -l 600 -p 16604 -t UDP_STREAM -- -m 64000
Fixes: b27b8dc77b5e ("igc: Increase timeout value for Speed 100/1000/2500")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230206235818.662384-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After calling irq_set_affinity_and_hint(), the cpumask pointer is
saved in desc->affinity_hint, and will be used later when reading
/proc/irq/<num>/affinity_hint. So the cpumask variable needs to be
persistent. Otherwise, we are accessing freed memory when reading
the affinity_hint file.
Also, need to clear affinity_hint before free_irq(), otherwise there
is a one-time warning and stack trace during module unloading:
[ 243.948687] WARNING: CPU: 10 PID: 1589 at kernel/irq/manage.c:1913 free_irq+0x318/0x360
...
[ 243.948753] Call Trace:
[ 243.948754] <TASK>
[ 243.948760] mana_gd_remove_irqs+0x78/0xc0 [mana]
[ 243.948767] mana_gd_remove+0x3e/0x80 [mana]
[ 243.948773] pci_device_remove+0x3d/0xb0
[ 243.948778] device_remove+0x46/0x70
[ 243.948782] device_release_driver_internal+0x1fe/0x280
[ 243.948785] driver_detach+0x4e/0xa0
[ 243.948787] bus_remove_driver+0x70/0xf0
[ 243.948789] driver_unregister+0x35/0x60
[ 243.948792] pci_unregister_driver+0x44/0x90
[ 243.948794] mana_driver_exit+0x14/0x3fe [mana]
[ 243.948800] __do_sys_delete_module.constprop.0+0x185/0x2f0
To fix the bug, use the persistent mask, cpumask_of(cpu#), and set
affinity_hint to NULL before freeing the IRQ, as required by free_irq().
Cc: stable@vger.kernel.org
Fixes: 71fa6887eeca ("net: mana: Assign interrupts to CPUs based on NUMA nodes")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/1675718929-19565-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Memory allocations in the network transmit path must use GFP_ATOMIC
so they won't sleep.
Reported-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/lkml/8a4d08f94d3e6fe8b6da68440eaa89a088ad84f9.camel@redhat.com/
Fixes: 846da38de0e8 ("net: netvsc: Add Isolation VM support for netvsc driver")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1675714317-48577-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, remove and reload flows can run in parallel to module cleanup.
This design is error prone. For example: aux_drivers callbacks are called
from both cleanup and remove flows with different lockings, which can
cause a deadlock[1].
Hence, serialize module cleanup with reload and remove.
[1]
cleanup remove
------- ------
auxiliary_driver_unregister();
devl_lock()
auxiliary_device_delete(mlx5e_aux)
device_lock(mlx5e_aux)
devl_lock()
device_lock(mlx5e_aux)
Fixes: 912cebf420c2 ("net/mlx5e: Connect ethernet part to auxiliary bus")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When tracer is reloaded, the device will log the traces at the
beginning of the log buffer. Also, driver is reading the log buffer in
chunks in accordance to the consumer index.
Hence, zero consumer index when reloading the tracer.
Fixes: 4383cfcc65e7 ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Whenever the driver is reading the string DBs into buffers, the driver
is setting the load bit, but the driver never clears this bit.
As a result, in case load bit is on and the driver query the device for
new string DBs, the driver won't read again the string DBs.
Fix it by clearing the load bit when query the device for new string
DBs.
Fixes: 2d69356752ff ("net/mlx5: Add support for fw live patch event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, each core device has VF pages counter which stores number of
fw pages used by its VFs and SFs.
The current design led to a hang when performing firmware reset on DPU,
where the DPU PFs stalled in sriov unload flow due to waiting on release
of SFs pages instead of waiting on only VFs pages.
Thus, Add a separate counter for SF firmware pages, which will prevent
the stall scenario described above.
Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, an independent page counter is used for tracking memory usage
for each function type such as VF, PF and host PF (DPU).
For better code-readibilty, use a single array that stores
the number of allocated memory pages for each function type.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
ethtool is returning an error for unknown speeds for the IPoIB interface:
$ ethtool ib0
netlink error: failed to retrieve link settings
netlink error: Invalid argument
netlink error: failed to retrieve link settings
netlink error: Invalid argument
Settings for ib0:
Link detected: no
After this change, ethtool will return success and show "unknown speed":
$ ethtool ib0
Settings for ib0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: no
Fixes: eb234ee9d541 ("net/mlx5e: IPoIB, Add support for get_link_ksettings in ethtool")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Moving to switchdev mode with rx-vlan-filter on and then setting it off
causes the kernel to crash since fs->vlan is freed during nic profile
cleanup flow.
RX VLAN filtering is not supported in switchdev mode so unset it when
changing to switchdev and restore its value when switching back to
legacy.
trace:
[] RIP: 0010:mlx5e_disable_cvlan_filter+0x43/0x70
[] set_feature_cvlan_filter+0x37/0x40 [mlx5_core]
[] mlx5e_handle_feature+0x3a/0x60 [mlx5_core]
[] mlx5e_set_features+0x6d/0x160 [mlx5_core]
[] __netdev_update_features+0x288/0xa70
[] ethnl_set_features+0x309/0x380
[] ? __nla_parse+0x21/0x30
[] genl_family_rcv_msg_doit.isra.17+0x110/0x150
[] genl_rcv_msg+0x112/0x260
[] ? features_reply_size+0xe0/0xe0
[] ? genl_family_rcv_msg_doit.isra.17+0x150/0x150
[] netlink_rcv_skb+0x4e/0x100
[] genl_rcv+0x24/0x40
[] netlink_unicast+0x1ab/0x290
[] netlink_sendmsg+0x257/0x4f0
[] sock_sendmsg+0x5c/0x70
Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
SWITCHDEV_FDB_ADD_TO_BRIDGE event handler that updates FDB entry 'lastuse'
field is only executed for eswitch that owns the entry. However, if peer
entry processed packets at least once it will have hardware counter 'used'
value greater than entry 'lastuse' from that point on, which will cause FDB
entry not being aged out.
Process the event on all eswitch instances.
Fixes: ff9b7521468b ("net/mlx5: Bridge, support LAG")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Selecting builder should be protected by the lock to prevent the case
where a new rule sets a builder in the nic_matcher while the previous
rule is still using the nic_matcher.
Fixing this issue and cleaning the error flow.
Fixes: b9b81e1e9382 ("net/mlx5: DR, For short chains of STEs, avoid allocating ste_arr dynamically")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
rq->hw_mtu is used in function en_rx.c/mlx5e_skb_from_cqe_mpwrq_linear()
to catch oversized packets. If FCS is concatenated to the end of the
packet then the check should be updated accordingly.
Rx rings initialization (mlx5e_init_rxq_rq()) invoked for every new set
of channels, as part of mlx5e_safe_switch_params(), unknowingly if it
runs with default configuration or not. Current rq->hw_mtu
initialization assumes default configuration and ignores
params->scatter_fcs_en flag state.
Fix this, by accounting for params->scatter_fcs_en flag state during
rq->hw_mtu initialization.
In addition, updating rq->hw_mtu value during ingress traffic might
lead to packets drop and oversize_pkts_sw_drop counter increase with no
good reason. Hence we remove this optimization and switch the set of
channels with a new one, to make sure we don't get false positives on
the oversize_pkts_sw_drop counter.
Fixes: 102722fc6832 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Adham Faris <afaris@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix handling of multiple OF framebuffer devices
- Fix booting on Socionext Synquacer with bad 'dma-ranges' entries
- Add DT binding .yamllint to .gitignore
* tag 'devicetree-fixes-for-6.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: interrupt-controller: arm,gic-v3: Fix typo in description of msi-controller property
dt-bindings: Fix .gitignore
of/address: Return an error when no valid dma-ranges are found
of: Make OF framebuffer device names unique
|
|
Alternative short title: don't instruct the hardware to match on
EtherType with "protocol 802.1Q" flower filters. It doesn't work for the
reasons detailed below.
With a command such as the following:
tc filter add dev $swp1 ingress chain $(IS1 2) pref 3 \
protocol 802.1Q flower skip_sw vlan_id 200 src_mac $h1_mac \
action vlan modify id 300 \
action goto chain $(IS2 0 0)
the created filter is set by ocelot_flower_parse_key() to be of type
OCELOT_VCAP_KEY_ETYPE, and etype is set to {value=0x8100, mask=0xffff}.
This gets propagated all the way to is1_entry_set() which commits it to
hardware (the VCAP_IS1_HK_ETYPE field of the key). Compare this to the
case where src_mac isn't specified - the key type is OCELOT_VCAP_KEY_ANY,
and is1_entry_set() doesn't populate VCAP_IS1_HK_ETYPE.
The problem is that for VLAN-tagged frames, the hardware interprets the
ETYPE field as holding the encapsulated VLAN protocol. So the above
filter will only match those packets which have an encapsulated protocol
of 0x8100, rather than all packets with VLAN ID 200 and the given src_mac.
The reason why this is allowed to occur is because, although we have a
block of code in ocelot_flower_parse_key() which sets "match_protocol"
to false when VLAN keys are present, that code executes too late.
There is another block of code, which executes for Ethernet addresses,
and has a "goto finished_key_parsing" and skips the VLAN header parsing.
By skipping it, "match_protocol" remains with the value it was
initialized with, i.e. "true", and "proto" is set to f->common.protocol,
or 0x8100.
The concept of ignoring some keys rather than erroring out when they are
present but can't be offloaded is dubious in itself, but is present
since the initial commit fe3490e6107e ("net: mscc: ocelot: Hardware
ofload for tc flower filter"), and it's outside of the scope of this
patch to change that.
The problem was introduced when the driver started to interpret the
flower filter's protocol, and populate the VCAP filter's ETYPE field
based on it.
To fix this, it is sufficient to move the code that parses the VLAN keys
earlier than the "goto finished_key_parsing" instruction. This will
ensure that if we have a flower filter with both VLAN and Ethernet
address keys, it won't match on ETYPE 0x8100, because the VLAN key
parsing sets "match_protocol = false".
Fixes: 86b956de119c ("net: mscc: ocelot: support matching on EtherType")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230205192409.1796428-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e9399 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Link: https://lore.kernel.org/netdev/trinity-e6294d28-636c-4c40-bb8b-b523521b00be-1674233135062@3c-app-gmx-bs36/
Fixes: e045124e9399 ("net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230205140713.1609281-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When ice_add_special_words() fails, the 'rm' is not released, which will
lead to a memory leak. Fix this up by going to 'err_unroll' label.
Compile tested only.
Fixes: 8b032a55c1bd ("ice: low level support for tunnels")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
The > comparison should be >= to prevent reading one element beyond
the end of the array.
The "vsi->num_rxq" is not strictly speaking the number of elements in
the vsi->rxq_map[] array. The array has "vsi->alloc_rxq" elements and
"vsi->num_rxq" is less than or equal to the number of elements in the
array. The array is allocated in ice_vsi_alloc_arrays(). It's still
an off by one but it might not access outside the end of the array.
Fixes: 143b86f346c7 ("ice: Enable RX queue selection using skbedit action")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
If the user turns on the vf-true-promiscuous-support flag, then Rx VLAN
filtering will be disabled if the VF requests to enable promiscuous
mode. When the VF is in a port VLAN, this is the incorrect behavior
because it will allow the VF to receive traffic outside of its port VLAN
domain. Fortunately this only resulted in the VF(s) receiving broadcast
traffic outside of the VLAN domain because all of the VLAN promiscuous
rules are based on the port VLAN ID. Fix this by setting the
.disable_rx_filtering VLAN op to a no-op when a port VLAN is enabled on
the VF.
Also, make sure to make this fix for both Single VLAN Mode and Double
VLAN Mode enabled devices.
Fixes: c31af68a1b94 ("ice: Add outer_vlan_ops and VSI specific VLAN ops implementations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
KASAN reported:
[ 9793.708867] BUG: KASAN: global-out-of-bounds in ice_get_link_speed+0x16/0x30 [ice]
[ 9793.709205] Read of size 4 at addr ffffffffc1271b1c by task kworker/6:1/402
[ 9793.709222] CPU: 6 PID: 402 Comm: kworker/6:1 Kdump: loaded Tainted: G B OE 6.1.0+ #3
[ 9793.709235] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.00.01.0014.070920180847 07/09/2018
[ 9793.709245] Workqueue: ice ice_service_task [ice]
[ 9793.709575] Call Trace:
[ 9793.709582] <TASK>
[ 9793.709588] dump_stack_lvl+0x44/0x5c
[ 9793.709613] print_report+0x17f/0x47b
[ 9793.709632] ? __cpuidle_text_end+0x5/0x5
[ 9793.709653] ? ice_get_link_speed+0x16/0x30 [ice]
[ 9793.709986] ? ice_get_link_speed+0x16/0x30 [ice]
[ 9793.710317] kasan_report+0xb7/0x140
[ 9793.710335] ? ice_get_link_speed+0x16/0x30 [ice]
[ 9793.710673] ice_get_link_speed+0x16/0x30 [ice]
[ 9793.711006] ice_vc_notify_vf_link_state+0x14c/0x160 [ice]
[ 9793.711351] ? ice_vc_repr_cfg_promiscuous_mode+0x120/0x120 [ice]
[ 9793.711698] ice_vc_process_vf_msg+0x7a7/0xc00 [ice]
[ 9793.712074] __ice_clean_ctrlq+0x98f/0xd20 [ice]
[ 9793.712534] ? ice_bridge_setlink+0x410/0x410 [ice]
[ 9793.712979] ? __request_module+0x320/0x520
[ 9793.713014] ? ice_process_vflr_event+0x27/0x130 [ice]
[ 9793.713489] ice_service_task+0x11cf/0x1950 [ice]
[ 9793.713948] ? io_schedule_timeout+0xb0/0xb0
[ 9793.713972] process_one_work+0x3d0/0x6a0
[ 9793.714003] worker_thread+0x8a/0x610
[ 9793.714031] ? process_one_work+0x6a0/0x6a0
[ 9793.714049] kthread+0x164/0x1a0
[ 9793.714071] ? kthread_complete_and_exit+0x20/0x20
[ 9793.714100] ret_from_fork+0x1f/0x30
[ 9793.714137] </TASK>
[ 9793.714151] The buggy address belongs to the variable:
[ 9793.714158] ice_aq_to_link_speed+0x3c/0xffffffffffff3520 [ice]
[ 9793.714632] Memory state around the buggy address:
[ 9793.714642] ffffffffc1271a00: f9 f9 f9 f9 00 00 05 f9 f9 f9 f9 f9 00 00 02 f9
[ 9793.714656] ffffffffc1271a80: f9 f9 f9 f9 00 00 04 f9 f9 f9 f9 f9 00 00 00 00
[ 9793.714670] >ffffffffc1271b00: 00 00 00 04 f9 f9 f9 f9 04 f9 f9 f9 f9 f9 f9 f9
[ 9793.714680] ^
[ 9793.714690] ffffffffc1271b80: 00 00 00 00 00 04 f9 f9 f9 f9 f9 f9 00 00 00 00
[ 9793.714704] ffffffffc1271c00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
The ICE_AQ_LINK_SPEED_UNKNOWN define is BIT(15). The value is bigger
than both legacy and normal link speed tables. Add one element (0 -
unknown) to both tables. There is no need to explicitly set table size,
leave it empty.
Fixes: 1d0e28a9be1f ("ice: Remove and replace ice speed defines with ethtool.h versions")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
When both ice and the irdma driver are loaded, a warning in
check_flush_dependency is being triggered. This is due to ice driver
workqueue being allocated with the WQ_MEM_RECLAIM flag and the irdma one
is not.
According to kernel documentation, this flag should be set if the
workqueue will be involved in the kernel's memory reclamation flow.
Since it is not, there is no need for the ice driver's WQ to have this
flag set so remove it.
Example trace:
[ +0.000004] workqueue: WQ_MEM_RECLAIM ice:ice_service_task [ice] is flushing !WQ_MEM_RECLAIM infiniband:0x0
[ +0.000139] WARNING: CPU: 0 PID: 728 at kernel/workqueue.c:2632 check_flush_dependency+0x178/0x1a0
[ +0.000011] Modules linked in: bonding tls xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_cha
in_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables nfnetlink bridge stp llc rfkill vfat fat intel_rapl_msr intel
_rapl_common isst_if_common skx_edac nfit libnvdimm x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm irqbypass crct1
0dif_pclmul crc32_pclmul ghash_clmulni_intel rapl intel_cstate rpcrdma sunrpc rdma_ucm ib_srpt ib_isert iscsi_target_mod target_
core_mod ib_iser libiscsi scsi_transport_iscsi rdma_cm ib_cm iw_cm iTCO_wdt iTCO_vendor_support ipmi_ssif irdma mei_me ib_uverbs
ib_core intel_uncore joydev pcspkr i2c_i801 acpi_ipmi mei lpc_ich i2c_smbus intel_pch_thermal ioatdma ipmi_si acpi_power_meter
acpi_pad xfs libcrc32c sd_mod t10_pi crc64_rocksoft crc64 sg ahci ixgbe libahci ice i40e igb crc32c_intel mdio i2c_algo_bit liba
ta dca wmi dm_mirror dm_region_hash dm_log dm_mod ipmi_devintf ipmi_msghandler fuse
[ +0.000161] [last unloaded: bonding]
[ +0.000006] CPU: 0 PID: 728 Comm: kworker/0:2 Tainted: G S 6.2.0-rc2_next-queue-13jan-00458-gc20aabd57164 #1
[ +0.000006] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0010.010620200716 01/06/2020
[ +0.000003] Workqueue: ice ice_service_task [ice]
[ +0.000127] RIP: 0010:check_flush_dependency+0x178/0x1a0
[ +0.000005] Code: 89 8e 02 01 e8 49 3d 40 00 49 8b 55 18 48 8d 8d d0 00 00 00 48 8d b3 d0 00 00 00 4d 89 e0 48 c7 c7 e0 3b 08
9f e8 bb d3 07 01 <0f> 0b e9 be fe ff ff 80 3d 24 89 8e 02 00 0f 85 6b ff ff ff e9 06
[ +0.000004] RSP: 0018:ffff88810a39f990 EFLAGS: 00010282
[ +0.000005] RAX: 0000000000000000 RBX: ffff888141bc2400 RCX: 0000000000000000
[ +0.000004] RDX: 0000000000000001 RSI: dffffc0000000000 RDI: ffffffffa1213a80
[ +0.000003] RBP: ffff888194bf3400 R08: ffffed117b306112 R09: ffffed117b306112
[ +0.000003] R10: ffff888bd983088b R11: ffffed117b306111 R12: 0000000000000000
[ +0.000003] R13: ffff888111f84d00 R14: ffff88810a3943ac R15: ffff888194bf3400
[ +0.000004] FS: 0000000000000000(0000) GS:ffff888bd9800000(0000) knlGS:0000000000000000
[ +0.000003] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ +0.000003] CR2: 000056035b208b60 CR3: 000000017795e005 CR4: 00000000007706f0
[ +0.000003] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ +0.000003] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ +0.000002] PKRU: 55555554
[ +0.000003] Call Trace:
[ +0.000002] <TASK>
[ +0.000003] __flush_workqueue+0x203/0x840
[ +0.000006] ? mutex_unlock+0x84/0xd0
[ +0.000008] ? __pfx_mutex_unlock+0x10/0x10
[ +0.000004] ? __pfx___flush_workqueue+0x10/0x10
[ +0.000006] ? mutex_lock+0xa3/0xf0
[ +0.000005] ib_cache_cleanup_one+0x39/0x190 [ib_core]
[ +0.000174] __ib_unregister_device+0x84/0xf0 [ib_core]
[ +0.000094] ib_unregister_device+0x25/0x30 [ib_core]
[ +0.000093] irdma_ib_unregister_device+0x97/0xc0 [irdma]
[ +0.000064] ? __pfx_irdma_ib_unregister_device+0x10/0x10 [irdma]
[ +0.000059] ? up_write+0x5c/0x90
[ +0.000005] irdma_remove+0x36/0x90 [irdma]
[ +0.000062] auxiliary_bus_remove+0x32/0x50
[ +0.000007] device_release_driver_internal+0xfa/0x1c0
[ +0.000005] bus_remove_device+0x18a/0x260
[ +0.000007] device_del+0x2e5/0x650
[ +0.000005] ? __pfx_device_del+0x10/0x10
[ +0.000003] ? mutex_unlock+0x84/0xd0
[ +0.000004] ? __pfx_mutex_unlock+0x10/0x10
[ +0.000004] ? _raw_spin_unlock+0x18/0x40
[ +0.000005] ice_unplug_aux_dev+0x52/0x70 [ice]
[ +0.000160] ice_service_task+0x1309/0x14f0 [ice]
[ +0.000134] ? __pfx___schedule+0x10/0x10
[ +0.000006] process_one_work+0x3b1/0x6c0
[ +0.000008] worker_thread+0x69/0x670
[ +0.000005] ? __kthread_parkme+0xec/0x110
[ +0.000007] ? __pfx_worker_thread+0x10/0x10
[ +0.000005] kthread+0x17f/0x1b0
[ +0.000005] ? __pfx_kthread+0x10/0x10
[ +0.000004] ret_from_fork+0x29/0x50
[ +0.000009] </TASK>
Fixes: 940b61af02f4 ("ice: Initialize PF and setup miscellaneous interrupt")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Jakub Andrysiak <jakub.andrysiak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
The touchscreen reports a battery status of 0% and jumps to 1% when a
stylus is used. The device ID was added and the battery ignore quirk was
enabled for it.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Link: https://lore.kernel.org/r/20230120223741.3007-1-l.guzenko@web.de
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
It was reported that commit b300667b33b2 ("HID: amd_sfh: Disable the
interrupt for all command") had caused increased resume time on HP Envy
x360.
Before this commit 3 sensors were reported, but they were not actually
functional. After this commit the sensors are no longer reported, but
also the resume time increased.
To avoid this problem explicitly look for the number of disabled sensors.
If all the sensors are disabled, clean everything up.
Fixes: b300667b33b2 ("HID: amd_sfh: Disable the interrupt for all command")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2115
Reported-by: Xaver Hugl <xaver.hugl@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20230203220850.13924-1-mario.limonciello@amd.com
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
The syzbot fuzzer detected a bug in the plusb network driver: A
zero-length control-OUT transfer was treated as a read instead of a
write. In modern kernels this error provokes a WARNING:
usb 1-1: BOGUS control dir, pipe 80000280 doesn't match bRequestType c0
WARNING: CPU: 0 PID: 4645 at drivers/usb/core/urb.c:411
usb_submit_urb+0x14a7/0x1880 drivers/usb/core/urb.c:411
Modules linked in:
CPU: 1 PID: 4645 Comm: dhcpcd Not tainted
6.2.0-rc6-syzkaller-00050-g9f266ccaa2f5 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
01/12/2023
RIP: 0010:usb_submit_urb+0x14a7/0x1880 drivers/usb/core/urb.c:411
...
Call Trace:
<TASK>
usb_start_wait_urb+0x101/0x4b0 drivers/usb/core/message.c:58
usb_internal_control_msg drivers/usb/core/message.c:102 [inline]
usb_control_msg+0x320/0x4a0 drivers/usb/core/message.c:153
__usbnet_read_cmd+0xb9/0x390 drivers/net/usb/usbnet.c:2010
usbnet_read_cmd+0x96/0xf0 drivers/net/usb/usbnet.c:2068
pl_vendor_req drivers/net/usb/plusb.c:60 [inline]
pl_set_QuickLink_features drivers/net/usb/plusb.c:75 [inline]
pl_reset+0x2f/0xf0 drivers/net/usb/plusb.c:85
usbnet_open+0xcc/0x5d0 drivers/net/usb/usbnet.c:889
__dev_open+0x297/0x4d0 net/core/dev.c:1417
__dev_change_flags+0x587/0x750 net/core/dev.c:8530
dev_change_flags+0x97/0x170 net/core/dev.c:8602
devinet_ioctl+0x15a2/0x1d70 net/ipv4/devinet.c:1147
inet_ioctl+0x33f/0x380 net/ipv4/af_inet.c:979
sock_do_ioctl+0xcc/0x230 net/socket.c:1169
sock_ioctl+0x1f8/0x680 net/socket.c:1286
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x197/0x210 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The fix is to call usbnet_write_cmd() instead of usbnet_read_cmd() and
remove the USB_DIR_IN flag.
Reported-and-tested-by: syzbot+2a0e7abd24f1eb90ce25@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 090ffa9d0e90 ("[PATCH] USB: usbnet (9/9) module for pl2301/2302 cables")
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/00000000000052099f05f3b3e298@google.com/
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some Logitech mice, such as the G903, and possibly the G403, the HID
events are generated on a different interface to the HID++ one.
If we enable hi-res through the HID++ interface, the HID interface
wouldn't know anything about it, and handle the events as if they were
regular scroll events, making the mouse unusable.
Disable hi-res scrolling on those devices until we implement scroll
events through HID++.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Tobias Klausmann <klausman@schwarzvogel.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216885
Fixes: 908d325e1665 ("HID: logitech-hidpp: Detect hi-res scrolling support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230203101800.139380-1-hadess@hadess.net
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
The initial value of hid->collection[].parent_idx if 0. When
Report descriptor doesn't contain "HID Collection", the value
remains as 0.
In the meanwhile, when the Report descriptor fullfill
all following conditions, it will trigger hid_apply_multiplier
function call.
1. Usage page is Generic Desktop Ctrls (0x01)
2. Usage is RESOLUTION_MULTIPLIER (0x48)
3. Contain any FEATURE items
The while loop in hid_apply_multiplier will search the top-most
collection by searching parent_idx == -1. Because all parent_idx
is 0. The loop will run forever.
There is a Report Descriptor triggerring the deadloop
0x05, 0x01, // Usage Page (Generic Desktop Ctrls)
0x09, 0x48, // Usage (0x48)
0x95, 0x01, // Report Count (1)
0x75, 0x08, // Report Size (8)
0xB1, 0x01, // Feature
Signed-off-by: Xin Zhao <xnzhao@google.com>
Link: https://lore.kernel.org/r/20230130212947.1315941-1-xnzhao@google.com
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Check all ports instead of just port_count ports. PTP init was only
checking ports 0 to port_count. If the hardware ports are not mapped
starting from 0 then they would be missed, e.g. if only ports 20-30 were
mapped it would attempt to init ports 0-10, resulting in NULL pointers
when attempting to timestamp. Now it will init all mapped ports.
Fixes: 70dfe25cd866 ("net: sparx5: Update extraction/injection for timestamping")
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes that resolve some reported problems.
These include:
- gadget driver fixes
- dwc3 driver fix
- typec driver fix
- MAINTAINERS file update.
All of these have been in linux-next with no reported problems"
* tag 'usb-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: ucsi: Don't attempt to resume the ports before they exist
usb: gadget: udc: do not clear gadget driver.bus
usb: gadget: f_uac2: Fix incorrect increment of bNumEndpoints
usb: gadget: f_fs: Fix unbalanced spinlock in __ffs_ep0_queue_wait
usb: dwc3: qcom: enable vbus override when in OTG dr-mode
MAINTAINERS: Add myself as UVC Gadget Maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small serial and vt fixes. These include:
- 8250 driver fixes relating to dma issues
- stm32 serial driver fix for threaded irqs
- vc_screen bugfix for reported problems.
All have been in linux-next for a while with no reported problems"
* tag 'tty-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF
serial: 8250_dma: Fix DMA Rx rearm race
serial: 8250_dma: Fix DMA Rx completion race
serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of small char/misc/whatever driver fixes. They
include:
- IIO driver fixes for some reported problems
- nvmem driver fixes
- fpga driver fixes
- debugfs memory leak fix in the hv_balloon and irqdomain code
(irqdomain change was acked by the maintainer)
All have been in linux-next with no reported problems"
* tag 'char-misc-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (33 commits)
kernel/irq/irqdomain.c: fix memory leak with using debugfs_lookup()
HV: hv_balloon: fix memory leak with using debugfs_lookup()
nvmem: qcom-spmi-sdam: fix module autoloading
nvmem: core: fix return value
nvmem: core: fix cell removal on error
nvmem: core: fix device node refcounting
nvmem: core: fix registration vs use race
nvmem: core: fix cleanup after dev_set_name()
nvmem: core: remove nvmem_config wp_gpio
nvmem: core: initialise nvmem->id early
nvmem: sunxi_sid: Always use 32-bit MMIO reads
nvmem: brcm_nvram: Add check for kzalloc
iio: imu: fxos8700: fix MAGN sensor scale and unit
iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
iio: imu: fxos8700: fix failed initialization ODR mode assignment
iio: imu: fxos8700: fix incorrect ODR mode readback
iio: light: cm32181: Fix PM support on system with 2 I2C resources
iio: hid: fix the retval in gyro_3d_capture_sample
iio: hid: fix the retval in accel_3d_capture_sample
iio: imu: st_lsm6dsx: fix build when CONFIG_IIO_TRIGGERED_BUFFER=m
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes from Helge Deller:
- fix fbcon to prevent fonts bigger than 32x32 pixels to avoid
overflows reported by syzbot
- switch omapfb to use kstrtobool()
- switch some fbdev drivers to use the backlight helpers
* tag 'fbdev-for-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbcon: Check font dimension limits
fbdev: omapfb: Use kstrtobool() instead of strtobool()
fbdev: fbmon: fix function name in kernel-doc
fbdev: atmel_lcdfb: Rework backlight status updates
fbdev: riva: Use backlight helper
fbdev: omapfb: panel-dsi-cm: Use backlight helper
fbdev: nvidia: Use backlight helper
fbdev: mx3fb: Use backlight helper
fbdev: radeon: Use backlight helper
fbdev: atyfb: Use backlight helper
fbdev: aty128fb: Use backlight helper
|
