| Age | Commit message (Collapse) | Author |
|---|
|
Fix the following compiler warning:
drivers/platform/x86/hp/hp-wmi.c:551:24: warning: cast to smaller integer
type 'enum hp_wmi_radio' from 'void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230123132824.660062-1-hdegoede@redhat.com
|
|
Some users may want to live with the bugs that exist in platform
firmware and have workarounds in AMD PMC driver.
To allow them to bypass these workarounds, introduce a module
parameter.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230120191519.15926-2-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
By default when the system is configured for low power idle in the FADT
the keyboard is set up as a wake source. This matches the behavior that
Windows uses for Modern Standby as well.
It has been reported that a variety of AMD based designs there are
spurious wakeups are happening where two IRQ sources are active.
For example:
```
PM: Triggering wakeup from IRQ 9
PM: Triggering wakeup from IRQ 1
```
In these designs IRQ 9 is the ACPI SCI and IRQ 1 is the keyboard.
One way to trigger this problem is to suspend the laptop and then unplug
the AC adapter. The SOC will be in a hardware sleep state and plugging
in the AC adapter returns control to the kernel's s2idle loop.
Normally if just IRQ 9 was active the s2idle loop would advance any EC
transactions and no other IRQ being active would cause the s2idle loop
to put the SOC back into hardware sleep state.
When this bug occurred IRQ 1 is also active even if no keyboard activity
occurred. This causes the s2idle loop to break and the system to wake.
This is a platform firmware bug triggering IRQ1 without keyboard activity.
This occurs in Windows as well, but Windows will enter "SW DRIPS" and
then with no activity enters back into "HW DRIPS" (hardware sleep state).
This issue affects Renoir, Lucienne, Cezanne, and Barcelo platforms. It
does not happen on newer systems such as Mendocino or Rembrandt.
It's been fixed in newer platform firmware. To avoid triggering the bug
on older systems check the SMU F/W version and adjust the policy at suspend
time for s2idle wakeup from keyboard on these systems. A lot of thought
and experimentation has been given around the timing of disabling IRQ1,
and to make it work the "suspend" PM callback is restored.
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: Xaver Hugl <xaver.hugl@gmail.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2115
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1951
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230120191519.15926-1-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Commit 1ea0d3b46798 ("platform/x86: asus-wmi: Simplify tablet-mode-switch
handling") unified the asus-wmi tablet-switch handling, but it did not take
into account that the value returned for the kbd_dock_devid WMI method is
inverted where as the other ones are not inverted.
This causes asus-wmi to report an inverted tablet-switch state for devices
which use the kbd_dock_devid, which causes libinput to ignore touchpad
events while the affected T10x model 2-in-1s are docked.
Add inverting of the return value in the kbd_dock_devid case to fix this.
Fixes: 1ea0d3b46798 ("platform/x86: asus-wmi: Simplify tablet-mode-switch handling")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230120143441.527334-1-hdegoede@redhat.com
|
|
To the best of my knowledge this is the same board as the B450M DS3H-CF,
but with an added WiFi card. Name obtained using dmidecode, tested
with force_load on v6.1.6
Signed-off-by: Kevin Kuriakose <kevinmkuriakose@gmail.com>
Acked-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230119150925.31962-1-kevinmkuriakose@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add support to map the "HP Omen Key" to KEY_PROG2. Laptops in the HP
Omen Series open the HP Omen Command Center application on windows. But,
on linux it fails with the following message from the hp-wmi driver:
[ 5143.415714] hp_wmi: Unknown event_id - 29 - 0x21a5
Also adds support to map Fn+Esc to KEY_FN_ESC. This currently throws the
following message on the hp-wmi driver:
[ 6082.143785] hp_wmi: Unknown key code - 0x21a7
There is also a "Win-Lock" key on HP Omen Laptops which supports
Enabling and Disabling the Windows key, which trigger commands 0x21a4
and 0x121a4 respectively, but I wasn't able to find any KEY in input.h
to map this to.
Signed-off-by: Rishit Bansal <rishitbansal0@gmail.com>
Link: https://lore.kernel.org/r/20230120221214.24426-1-rishitbansal0@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Some platforms send the speaker-mute key from EC. dell-wmi can't
recognize it.
Add a new keymap for KEY_MUTE in type 0x0010 table.
Signed-off-by: Koba Ko <koba.ko@canonical.com>
Link: https://lore.kernel.org/r/20230117123436.200440-1-koba.ko@canonical.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Instead of cleaning the entire loaded kernel image to the PoC and
disabling the MMU and caches before branching to the kernel's bare metal
entry point, we can leave the MMU and caches enabled, and rely on EFI's
cacheable 1:1 mapping of all of system RAM (which is mandated by the
spec) to populate the initial page tables.
This removes the need for managing coherency in software, which is
tedious and error prone.
Note that we still need to clean the executable region of the image to
the PoU if this is required for I/D coherency, but only if we actually
decided to move the image in memory, as otherwise, this will have been
taken care of by the loader.
This change affects both the builtin EFI stub as well as the zboot
decompressor, which now carries the entire EFI stub along with the
decompression code and the compressed image.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20230111102236.1430401-7-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The ACPICA code has been built with '-Os' since the beginning of git
history, though there's no explanatory comment as to why.
This is unfortunate as GCC drops the alignment specificed by
'-falign-functions=N' when '-Os' is used, as reported in GCC bug 88345:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=88345
This prevents CONFIG_FUNCTION_ALIGNMENT and
CONFIG_DEBUG_FORCE_FUNCTION_ALIGN_64B from having their expected effect
on the ACPICA code. This is doubly unfortunate as in subsequent patches
arm64 will depend upon CONFIG_FUNCTION_ALIGNMENT for its ftrace
implementation.
Drop the '-Os' flag when building the ACPICA code. With this removed,
the code builds cleanly and works correctly in testing so far.
I've tested this by selecting CONFIG_DEBUG_FORCE_FUNCTION_ALIGN_64B=y,
building and booting a kernel using ACPI, and looking for misaligned
text symbols:
* arm64:
Before, v6.2-rc3:
# uname -rm
6.2.0-rc3 aarch64
# grep ' [Tt] ' /proc/kallsyms | grep -iv '[048c]0 [Tt] ' | wc -l
5009
Before, v6.2-rc3 + fixed __cold:
# uname -rm
6.2.0-rc3-00001-g2a2bedf8bfa9 aarch64
# grep ' [Tt] ' /proc/kallsyms | grep -iv '[048c]0 [Tt] ' | wc -l
919
After:
# uname -rm
6.2.0-rc3-00002-g267bddc38572 aarch64
# grep ' [Tt] ' /proc/kallsyms | grep -iv '[048c]0 [Tt] ' | wc -l
323
# grep ' [Tt] ' /proc/kallsyms | grep -iv '[048c]0 [Tt] ' | grep acpi | wc -l
0
* x86_64:
Before, v6.2-rc3:
# uname -rm
6.2.0-rc3 x86_64
# grep ' [Tt] ' /proc/kallsyms | grep -iv '[048c]0 [Tt] ' | wc -l
11537
Before, v6.2-rc3 + fixed __cold:
# uname -rm
6.2.0-rc3-00001-g2a2bedf8bfa9 x86_64
# grep ' [Tt] ' /proc/kallsyms | grep -iv '[048c]0 [Tt] ' | wc -l
2805
After:
# uname -rm
6.2.0-rc3-00002-g267bddc38572 x86_64
# grep ' [Tt] ' /proc/kallsyms | grep -iv '[048c]0 [Tt] ' | wc -l
1357
# grep ' [Tt] ' /proc/kallsyms | grep -iv '[048c]0 [Tt] ' | grep acpi | wc -l
0
With the patch applied, the remaining unaligned text labels are a
combination of static call trampolines and labels in assembly, which can
be dealt with in subsequent patches.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Florent Revest <revest@chromium.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Deacon <will@kernel.org>
Cc: linux-acpi@vger.kernel.org
Link: https://lore.kernel.org/r/20230123134603.1064407-4-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The driver browses the trip point to find out the critical trip
temperature. However the function thermal_zone_get_crit_temp() does
already that, so the routine is pointless in the driver.
Use thermal_zone_get_crit_temp() instead of inspecting all the trip
points.
In addition, the hysteresis value is set to zero. A critical trip
point does not have a hysteresis.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230118222610.186088-1-daniel.lezcano@linaro.org
|
|
Add support for V3 generation thermal found in MT7986 and MT7981 SoCs.
Brings code to assign values from efuse as well as new function to
convert raw temperature to millidegree celsius, as found in MediaTek's
SDK sources (but cleaned up and de-duplicated)
[1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/baf36c7eef477aae1f8f2653b6c29e2caf48475b
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/2d341fc45266217249586eb4bd3be3ac4ca83a12.1674055882.git.daniel@makrotopia.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Instead of having if-else logic selecting either raw_to_mcelsius_v1 or
raw_to_mcelsius_v2 in mtk_thermal_bank_temperature introduce a function
pointer raw_to_mcelsius to struct mtk_thermal which is initialized in the
probe function.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/69c17529e8418da3eec703dde31e1b01e5b0f7e8.1674055882.git.daniel@makrotopia.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Use TEMP_CALIB_MASK macro instead of raw number.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230123102319.37710-1-frank.li@vivo.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The DRM fbdev emulation layer sets the struct fb_info .fbdefio field to
a struct fb_deferred_io pointer, that is shared across all drivers that
use the generic drm_fbdev_generic_setup() helper function.
It is a problem because the fbdev core deferred I/O logic assumes that
the struct fb_deferred_io data is not shared between devices, and it's
stored there state such as the list of pages touched and a mutex that
is use to synchronize between the fb_deferred_io_track_page() function
that track the dirty pages and fb_deferred_io_work() workqueue handler
doing the actual deferred I/O.
The latter can lead to the following error, since it may happen that two
drivers are probed and then one is removed, which causes the mutex bo be
destroyed and not existing anymore by the time the other driver tries to
grab it for the fbdev deferred I/O logic:
[ 369.756553] ------------[ cut here ]------------
[ 369.756604] DEBUG_LOCKS_WARN_ON(lock->magic != lock)
[ 369.756631] WARNING: CPU: 2 PID: 1023 at kernel/locking/mutex.c:582 __mutex_lock+0x348/0x424
[ 369.756744] Modules linked in: nf_conntrack_netbios_ns nf_conntrack_broadcast nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ip
v6 nf_defrag_ipv4 ip_set nf_tables nfnetlink qrtr btsdio bluetooth sunrpc brcmfmac snd_soc_hdmi_codec cpufreq_dt cfg80211 vfat fat vc4 rfkill brcmutil raspberrypi_cpufreq i2c_bcm2835 iproc_rng200 bcm2711_thermal snd_soc_core snd_pcm_dmaen
gine leds_gpio nvmem_rmem joydev hid_cherry uas usb_storage gpio_raspberrypi_exp v3d snd_pcm raspberrypi_hwmon gpu_sched bcm2835_wdt broadcom bcm_phy_lib snd_timer genet snd mdio_bcm_unimac clk_bcm2711_dvp soundcore drm_display_helper pci
e_brcmstb cec ip6_tables ip_tables fuse
[ 369.757400] CPU: 2 PID: 1023 Comm: fbtest Not tainted 5.19.0-rc6+ #94
[ 369.757455] Hardware name: raspberrypi,4-model-b Raspberry Pi 4 Model B Rev 1.4/Raspberry Pi 4 Model B Rev 1.4, BIOS 2022.10 10/01/2022
[ 369.757538] pstate: 00400005 (nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 369.757596] pc : __mutex_lock+0x348/0x424
[ 369.757635] lr : __mutex_lock+0x348/0x424
[ 369.757672] sp : ffff80000953bb00
[ 369.757703] x29: ffff80000953bb00 x28: ffff17fdc087c000 x27: 0000000000000002
[ 369.757771] x26: ffff17fdc349f9b0 x25: fffffc5ff72e0100 x24: 0000000000000000
[ 369.757838] x23: 0000000000000000 x22: 0000000000000002 x21: ffffa618df636f10
[ 369.757903] x20: ffff80000953bb68 x19: ffffa618e0f18138 x18: 0000000000000001
[ 369.757968] x17: 0000000020000000 x16: 0000000000000002 x15: 0000000000000000
[ 369.758032] x14: 0000000000000000 x13: 284e4f5f4e524157 x12: 5f534b434f4c5f47
[ 369.758097] x11: 00000000ffffdfff x10: ffffa618e0c79f88 x9 : ffffa618de472484
[ 369.758162] x8 : 000000000002ffe8 x7 : c0000000ffffdfff x6 : 00000000000affa8
[ 369.758227] x5 : 0000000000001fff x4 : 0000000000000000 x3 : 0000000000000027
[ 369.758292] x2 : 0000000000000001 x1 : ffff17fdc087c000 x0 : 0000000000000028
[ 369.758357] Call trace:
[ 369.758383] __mutex_lock+0x348/0x424
[ 369.758420] mutex_lock_nested+0x4c/0x5c
[ 369.758459] fb_deferred_io_mkwrite+0x78/0x1d8
[ 369.758507] do_page_mkwrite+0x5c/0x19c
[ 369.758550] wp_page_shared+0x70/0x1a0
[ 369.758590] do_wp_page+0x3d0/0x510
[ 369.758628] handle_pte_fault+0x1c0/0x1e0
[ 369.758670] __handle_mm_fault+0x250/0x380
[ 369.758712] handle_mm_fault+0x17c/0x3a4
[ 369.758753] do_page_fault+0x158/0x530
[ 369.758792] do_mem_abort+0x50/0xa0
[ 369.758831] el0_da+0x78/0x19c
[ 369.758864] el0t_64_sync_handler+0xbc/0x150
[ 369.758904] el0t_64_sync+0x190/0x194
[ 369.758942] irq event stamp: 11395
[ 369.758973] hardirqs last enabled at (11395): [<ffffa618de472554>] __up_console_sem+0x74/0x80
[ 369.759042] hardirqs last disabled at (11394): [<ffffa618de47254c>] __up_console_sem+0x6c/0x80
[ 369.760554] softirqs last enabled at (11392): [<ffffa618de330a74>] __do_softirq+0x4c4/0x6b8
[ 369.762060] softirqs last disabled at (11383): [<ffffa618de3c9124>] __irq_exit_rcu+0x104/0x214
[ 369.763564] ---[ end trace 0000000000000000 ]---
Fixes: d536540f304c ("drm/fb-helper: Add generic fbdev emulation .fb_probe function")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230121192418.2814955-4-javierm@redhat.com
|
|
The fb_deferred_io_init() can fail and return an errno code but currently
there is no check for its return value.
Fix that and propagate to errno to the caller in the case of a failure.
Fixes: d536540f304c ("drm/fb-helper: Add generic fbdev emulation .fb_probe function")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230121192418.2814955-3-javierm@redhat.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-01-20 (iavf)
This series contains updates to iavf driver only.
Michal Schmidt converts single iavf workqueue to per adapter to avoid
deadlock issues.
Marcin moves setting of VLAN related netdev features to watchdog task to
avoid RTNL deadlock.
Stefan Assmann schedules immediate watchdog task execution on changing
primary MAC to avoid excessive delay.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: schedule watchdog immediately when changing primary MAC
iavf: Move netdev_update_features() into watchdog task
iavf: fix temporary deadlock and failure to set MAC address
====================
Link: https://lore.kernel.org/r/20230120211036.430946-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Driver marked broadcast/multicast frames as offloaded incorrectly.
Mark them as offloaded only when HW offloading has been enabled.
This should happen only for ADIN2111 when both ports are bridged
by the software.
Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230120090846.18172-1-alexandru.tachici@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting with commit eee16b147121 ("net: dsa: microchip: perform the
compatibility check for dev probed"), the KSZ switch driver now bails
out if it thinks the DT compatible doesn't match the actual chip ID
read back from the hardware:
ksz9477-switch 1-005f: Device tree specifies chip KSZ9893 but found
KSZ8563, please fix it!
For the KSZ8563, which used ksz_switch_chips[KSZ9893], this was fine
at first, because it indeed shares the same chip id as the KSZ9893.
Commit b44908095612 ("net: dsa: microchip: add separate struct
ksz_chip_data for KSZ8563 chip") started differentiating KSZ9893
compatible chips by consulting the 0x1F register. The resulting breakage
was fixed for the SPI driver in the same commit by introducing the
appropriate ksz_switch_chips[KSZ8563], but not for the I2C driver.
Fix this for I2C-connected KSZ8563 now to get it probing again.
Fixes: b44908095612 ("net: dsa: microchip: add separate struct ksz_chip_data for KSZ8563 chip").
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230120110933.1151054-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On 32-bit architectures with 64-bit resource_size_t, sp_rtc_probe()
causes a compiler warning:
drivers/rtc/rtc-sunplus.c: In function 'sp_rtc_probe':
drivers/rtc/rtc-sunplus.c:243:33: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
243 | dev_dbg(&plat_dev->dev, "res = 0x%x, reg_base = 0x%lx\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The best way to print a resource is the special %pR format string,
and similarly to print a pointer we can use %p and avoid the cast.
Fixes: fad6cbe9b2b4 ("rtc: Add driver for RTC in Sunplus SP7021")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230117172450.2938962-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Asus U46E backlight tables have a set of interesting problems:
1. Its ACPI tables do make _OSI ("Windows 2012") checks, so
acpi_osi_is_win8() should return true.
But the tables have 2 sets of _OSI calls, one from the usual global
_INI method setting a global OSYS variable and a second set of _OSI
calls from a MSOS method and the MSOS method is the only one calling
_OSI ("Windows 2012").
The MSOS method only gets called in the following cases:
1. From some Asus specific WMI methods
2. From _DOD, which only runs after acpi_video_get_backlight_type()
has already been called by the i915 driver
3. From other ACPI video bus methods which never run (see below)
4. From some EC query callbacks
So when i915 calls acpi_video_get_backlight_type() MSOS has never run
and acpi_osi_is_win8() returns false, so acpi_video_get_backlight_type()
returns acpi_video as the desired backlight type, which causes
the intel_backlight device to not register.
2. _DOD effectively does this:
Return (Package (0x01)
{
0x0400
})
causing acpi_video_device_in_dod() to return false, which causes
the acpi_video backlight device to not register.
Leaving the user with no backlight device at all. Note that before 6.1.y
the i915 driver would register the intel_backlight device unconditionally
and since that then was the only backlight device userspace would use that.
Add a backlight=native DMI quirk for this special laptop to restore
the old (and working) behavior of the intel_backlight device registering.
Fixes: fb1836c91317 ("ACPI: video: Prefer native over vendor")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The HP EliteBook 8460p predates Windows 8, so it defaults to using
acpi_video# for backlight control.
Starting with the 6.1.y kernels the native radeon_bl0 backlight is hidden
in this case instead of relying on userspace preferring acpi_video# over
native backlight devices.
It turns out that for the acpi_video# interface to work on
the HP EliteBook 8460p, the brightness needs to be set at least once
through the native interface, which now no longer is done breaking
backlight control.
The native interface however always works without problems, so add
a quirk to use native backlight on the EliteBook 8460p to fix this.
Fixes: fb1836c91317 ("ACPI: video: Prefer native over vendor")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2161428
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The HP Pavilion g6-1d80nr predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native backlight interface which does
work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull VFIO fixes from Alex Williamson:
- Honor reserved regions when testing for IOMMU find grained super page
support, avoiding a regression on s390 for a firmware device where
the existence of the mapping, even if unused can trigger an error
state. (Niklas Schnelle)
- Fix a deadlock in releasing KVM references by using the alternate
.release() rather than .destroy() callback for the kvm-vfio device.
(Yi Liu)
* tag 'vfio-v6.2-rc6' of https://github.com/awilliam/linux-vfio:
kvm/vfio: Fix potential deadlock on vfio group_lock
vfio/type1: Respect IOMMU reserved regions in vfio_test_domain_fgsp()
|
|
The definition of intel_selftest_modify_policy() does not match the
declaration, as gcc-13 points out:
drivers/gpu/drm/i915/selftests/intel_scheduler_helpers.c:29:5: error: conflicting types for 'intel_selftest_modify_policy' due to enum/integer mismatch; have 'int(struct intel_engine_cs *, struct intel_selftest_saved_policy *, u32)' {aka 'int(struct intel_engine_cs *, struct intel_selftest_saved_policy *, unsigned int)'} [-Werror=enum-int-mismatch]
29 | int intel_selftest_modify_policy(struct intel_engine_cs *engine,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/gpu/drm/i915/selftests/intel_scheduler_helpers.c:11:
drivers/gpu/drm/i915/selftests/intel_scheduler_helpers.h:28:5: note: previous declaration of 'intel_selftest_modify_policy' with type 'int(struct intel_engine_cs *, struct intel_selftest_saved_policy *, enum selftest_scheduler_modify)'
28 | int intel_selftest_modify_policy(struct intel_engine_cs *engine,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Change the type in the definition to match.
Fixes: 617e87c05c72 ("drm/i915/selftest: Fix hangcheck self test for GuC submission")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230117163743.1003219-1-arnd@kernel.org
(cherry picked from commit 8d7eb8ed3f83f248e01a4f548d9c500a950a2c2d)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Commit 0d0e7d1eea9e ("drm/i915/mtl: Define engine context layouts")
added the engine context for Meteor Lake. In a second revision of the
patch it was believed the xcs offsets were wrong due to a tagging
issue in the spec. The first version was actually correct, as shown
by the intel_lrc_live_selftests/live_lrc_layout test:
i915: Running gt_lrc
i915: Running intel_lrc_live_selftests/live_lrc_layout
bcs0: LRI command mismatch at dword 1, expected 1108101d found 11081019
[drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
bcs0: HW register image:
[0000] 00000000 1108101d 00022244 ffff0008 00022034 00000088 00022030 00000088
...
bcs0: SW register image:
[0000] 00000000 11081019 00022244 00090009 00022034 00000000 00022030 00000000
The difference in the 2 additional dwords (0x1d vs 0x19) are the offsets
0x120 / 0x124 that are indeed part of the context image.
Bspec: 45585
Fixes: 0d0e7d1eea9e ("drm/i915/mtl: Define engine context layouts")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230111235531.3353815-2-radhakrishna.sripada@intel.com
(cherry picked from commit ca54a9a32da0f0ef7e5cbcd111b66f3c9d78b7d2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
|
|
ctrl->ops is used by nvme_alloc_admin_tag_set() but set by
nvme_init_ctrl() so reorder the calls to avoid a NULL pointer
dereference.
Fixes: 6dfba1c09c10 ("nvme-fc: use the tagset alloc/free helpers")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
commit 1796f808e4bb ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
adjusted the policy to enable wakeup by default if the ACPI tables
indicated that a device was wake capable.
It was reported however that this broke suspend on at least two System76
systems in S3 mode and two Lenovo Gen2a systems, but only with S3.
When the machines are set to s2idle, wakeup behaves properly.
Configuring the GPIOs for wakeup with S3 doesn't work properly, so only
set it when the system supports low power idle.
Fixes: 1796f808e4bb ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
Fixes: b38f2d5d9615c ("i2c: acpi: Use ACPI wake capability bit to set wake_irq")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2357
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2162013
Reported-by: Nathan Smythe <ncsmythe@scruboak.org>
Tested-by: Nathan Smythe <ncsmythe@scruboak.org>
Suggested-by: Raul Rangel <rrangel@chromium.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The page_pool_release_page was used when freeing rx buffers, and this
function just unmaps the page (if mapped) and does not recycle the page.
So after hundreds of down/up the eth0, the system will out of memory.
For more details, please refer to the following reproduce steps and
bug logs. To solve this issue and refer to the doc of page pool, the
page_pool_put_full_page should be used to replace page_pool_release_page.
Because this API will try to recycle the page if the page refcnt equal to
1. After testing 20000 times, the issue can not be reproduced anymore
(about testing 391 times the issue will occur on i.MX8MN-EVK before).
Reproduce steps:
Create the test script and run the script. The script content is as
follows:
LOOPS=20000
i=1
while [ $i -le $LOOPS ]
do
echo "TINFO:ENET $curface up and down test $i times"
org_macaddr=$(cat /sys/class/net/eth0/address)
ifconfig eth0 down
ifconfig eth0 hw ether $org_macaddr up
i=$(expr $i + 1)
done
sleep 5
if cat /sys/class/net/eth0/operstate | grep 'up';then
echo "TEST PASS"
else
echo "TEST FAIL"
fi
Bug detail logs:
TINFO:ENET up and down test 391 times
[ 850.471205] Qualcomm Atheros AR8031/AR8033 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
[ 853.535318] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 853.541694] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 870.590531] page_pool_release_retry() stalled pool shutdown 199 inflight 60 sec
[ 931.006557] page_pool_release_retry() stalled pool shutdown 199 inflight 120 sec
TINFO:ENET up and down test 392 times
[ 991.426544] page_pool_release_retry() stalled pool shutdown 192 inflight 181 sec
[ 1051.838531] page_pool_release_retry() stalled pool shutdown 170 inflight 241 sec
[ 1093.751217] Qualcomm Atheros AR8031/AR8033 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
[ 1096.446520] page_pool_release_retry() stalled pool shutdown 308 inflight 60 sec
[ 1096.831245] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1096.839092] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1112.254526] page_pool_release_retry() stalled pool shutdown 103 inflight 302 sec
[ 1156.862533] page_pool_release_retry() stalled pool shutdown 308 inflight 120 sec
[ 1172.674516] page_pool_release_retry() stalled pool shutdown 103 inflight 362 sec
[ 1217.278532] page_pool_release_retry() stalled pool shutdown 308 inflight 181 sec
TINFO:ENET up and down test 393 times
[ 1233.086535] page_pool_release_retry() stalled pool shutdown 103 inflight 422 sec
[ 1277.698513] page_pool_release_retry() stalled pool shutdown 308 inflight 241 sec
[ 1293.502525] page_pool_release_retry() stalled pool shutdown 86 inflight 483 sec
[ 1338.110518] page_pool_release_retry() stalled pool shutdown 308 inflight 302 sec
[ 1353.918540] page_pool_release_retry() stalled pool shutdown 32 inflight 543 sec
[ 1361.179205] Qualcomm Atheros AR8031/AR8033 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
[ 1364.255298] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1364.263189] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1371.998532] page_pool_release_retry() stalled pool shutdown 310 inflight 60 sec
[ 1398.530542] page_pool_release_retry() stalled pool shutdown 308 inflight 362 sec
[ 1414.334539] page_pool_release_retry() stalled pool shutdown 16 inflight 604 sec
[ 1432.414520] page_pool_release_retry() stalled pool shutdown 310 inflight 120 sec
[ 1458.942523] page_pool_release_retry() stalled pool shutdown 308 inflight 422 sec
[ 1474.750521] page_pool_release_retry() stalled pool shutdown 16 inflight 664 sec
TINFO:ENET up and down test 394 times
[ 1492.830522] page_pool_release_retry() stalled pool shutdown 310 inflight 181 sec
[ 1519.358519] page_pool_release_retry() stalled pool shutdown 308 inflight 483 sec
[ 1535.166545] page_pool_release_retry() stalled pool shutdown 2 inflight 724 sec
[ 1537.090278] eth_test2.sh invoked oom-killer: gfp_mask=0x400dc0(GFP_KERNEL_ACCOUNT|__GFP_ZERO), order=0, oom_score_adj=0
[ 1537.101192] CPU: 3 PID: 2379 Comm: eth_test2.sh Tainted: G C 6.1.1+g56321e101aca #1
[ 1537.110249] Hardware name: NXP i.MX8MNano EVK board (DT)
[ 1537.115561] Call trace:
[ 1537.118005] dump_backtrace.part.0+0xe0/0xf0
[ 1537.122289] show_stack+0x18/0x40
[ 1537.125608] dump_stack_lvl+0x64/0x80
[ 1537.129276] dump_stack+0x18/0x34
[ 1537.132592] dump_header+0x44/0x208
[ 1537.136083] oom_kill_process+0x2b4/0x2c0
[ 1537.140097] out_of_memory+0xe4/0x594
[ 1537.143766] __alloc_pages+0xb68/0xd00
[ 1537.147521] alloc_pages+0xac/0x160
[ 1537.151013] __get_free_pages+0x14/0x40
[ 1537.154851] pgd_alloc+0x1c/0x30
[ 1537.158082] mm_init+0xf8/0x1d0
[ 1537.161228] mm_alloc+0x48/0x60
[ 1537.164368] alloc_bprm+0x7c/0x240
[ 1537.167777] do_execveat_common.isra.0+0x70/0x240
[ 1537.172486] __arm64_sys_execve+0x40/0x54
[ 1537.176502] invoke_syscall+0x48/0x114
[ 1537.180255] el0_svc_common.constprop.0+0xcc/0xec
[ 1537.184964] do_el0_svc+0x2c/0xd0
[ 1537.188280] el0_svc+0x2c/0x84
[ 1537.191340] el0t_64_sync_handler+0xf4/0x120
[ 1537.195613] el0t_64_sync+0x18c/0x190
[ 1537.199334] Mem-Info:
[ 1537.201620] active_anon:342 inactive_anon:10343 isolated_anon:0
[ 1537.201620] active_file:54 inactive_file:112 isolated_file:0
[ 1537.201620] unevictable:0 dirty:0 writeback:0
[ 1537.201620] slab_reclaimable:2620 slab_unreclaimable:7076
[ 1537.201620] mapped:1489 shmem:2473 pagetables:466
[ 1537.201620] sec_pagetables:0 bounce:0
[ 1537.201620] kernel_misc_reclaimable:0
[ 1537.201620] free:136672 free_pcp:96 free_cma:129241
[ 1537.240419] Node 0 active_anon:1368kB inactive_anon:41372kB active_file:216kB inactive_file:5052kB unevictable:0kB isolated(anon):0kB isolated(file):0kB s
[ 1537.271422] Node 0 DMA free:541636kB boost:0kB min:30000kB low:37500kB high:45000kB reserved_highatomic:0KB active_anon:1368kB inactive_anon:41372kB actiB
[ 1537.300219] lowmem_reserve[]: 0 0 0 0
[ 1537.303929] Node 0 DMA: 1015*4kB (UMEC) 743*8kB (UMEC) 417*16kB (UMEC) 235*32kB (UMEC) 116*64kB (UMEC) 25*128kB (UMEC) 4*256kB (UC) 2*512kB (UC) 0*1024kBB
[ 1537.323938] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=1048576kB
[ 1537.332708] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=32768kB
[ 1537.341292] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=2048kB
[ 1537.349776] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=64kB
[ 1537.358087] 2939 total pagecache pages
[ 1537.361876] 0 pages in swap cache
[ 1537.365229] Free swap = 0kB
[ 1537.368147] Total swap = 0kB
[ 1537.371065] 516096 pages RAM
[ 1537.373959] 0 pages HighMem/MovableOnly
[ 1537.377834] 17302 pages reserved
[ 1537.381103] 163840 pages cma reserved
[ 1537.384809] 0 pages hwpoisoned
[ 1537.387902] Tasks state (memory values in pages):
[ 1537.392652] [ pid ] uid tgid total_vm rss pgtables_bytes swapents oom_score_adj name
[ 1537.401356] [ 201] 993 201 1130 72 45056 0 0 rpcbind
[ 1537.409772] [ 202] 0 202 4529 1640 77824 0 -250 systemd-journal
[ 1537.418861] [ 222] 0 222 4691 801 69632 0 -1000 systemd-udevd
[ 1537.427787] [ 248] 994 248 20914 130 65536 0 0 systemd-timesyn
[ 1537.436884] [ 497] 0 497 620 31 49152 0 0 atd
[ 1537.444938] [ 500] 0 500 854 77 53248 0 0 crond
[ 1537.453165] [ 503] 997 503 1470 160 49152 0 -900 dbus-daemon
[ 1537.461908] [ 505] 0 505 633 24 40960 0 0 firmwared
[ 1537.470491] [ 513] 0 513 2507 180 61440 0 0 ofonod
[ 1537.478800] [ 514] 990 514 69640 137 81920 0 0 parsec
[ 1537.487120] [ 533] 0 533 599 39 40960 0 0 syslogd
[ 1537.495518] [ 534] 0 534 4546 148 65536 0 0 systemd-logind
[ 1537.504560] [ 535] 0 535 690 24 45056 0 0 tee-supplicant
[ 1537.513564] [ 540] 996 540 2769 168 61440 0 0 systemd-network
[ 1537.522680] [ 566] 0 566 3878 228 77824 0 0 connmand
[ 1537.531168] [ 645] 998 645 1538 133 57344 0 0 avahi-daemon
[ 1537.540004] [ 646] 998 646 1461 64 57344 0 0 avahi-daemon
[ 1537.548846] [ 648] 992 648 781 41 45056 0 0 rpc.statd
[ 1537.557415] [ 650] 64371 650 590 23 45056 0 0 ninfod
[ 1537.565754] [ 653] 61563 653 555 24 45056 0 0 rdisc
[ 1537.573971] [ 655] 0 655 374569 2999 290816 0 -999 containerd
[ 1537.582621] [ 658] 0 658 1311 20 49152 0 0 agetty
[ 1537.590922] [ 663] 0 663 1529 97 49152 0 0 login
[ 1537.599138] [ 666] 0 666 3430 202 69632 0 0 wpa_supplicant
[ 1537.608147] [ 667] 0 667 2344 96 61440 0 0 systemd-userdbd
[ 1537.617240] [ 677] 0 677 2964 314 65536 0 100 systemd
[ 1537.625651] [ 679] 0 679 3720 646 73728 0 100 (sd-pam)
[ 1537.634138] [ 687] 0 687 1289 403 45056 0 0 sh
[ 1537.642108] [ 789] 0 789 970 93 45056 0 0 eth_test2.sh
[ 1537.650955] [ 2355] 0 2355 2346 94 61440 0 0 systemd-userwor
[ 1537.660046] [ 2356] 0 2356 2346 94 61440 0 0 systemd-userwor
[ 1537.669137] [ 2358] 0 2358 2346 95 57344 0 0 systemd-userwor
[ 1537.678258] [ 2379] 0 2379 970 93 45056 0 0 eth_test2.sh
[ 1537.687098] oom-kill:constraint=CONSTRAINT_NONE,nodemask=(null),cpuset=/,mems_allowed=0,global_oom,task_memcg=/user.slice/user-0.slice/user@0.service,tas0
[ 1537.703009] Out of memory: Killed process 679 ((sd-pam)) total-vm:14880kB, anon-rss:2584kB, file-rss:0kB, shmem-rss:0kB, UID:0 pgtables:72kB oom_score_ad0
[ 1553.246526] page_pool_release_retry() stalled pool shutdown 310 inflight 241 sec
Fixes: 95698ff6177b ("net: fec: using page pool to manage RX buffers")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: shenwei wang <Shenwei.wang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fixes from Borislav Petkov:
- Respect user-supplied polling value in the EDAC device code
- Fix a use-after-free issue in qcom_edac
* tag 'edac_urgent_for_v6.2_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/qcom: Do not pass llcc_driv_data as edac_device_ctl_info's pvt_info
EDAC/device: Respect any driver-supplied workqueue polling value
|
|
Increase the maximum time to wait for verification of a queue reset
operation to 200ms.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230118203111.529766-7-akrowiak@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Some response codes returned from the queue reset function are not being
handled correctly; this patch fixes them:
1. Response code 3, AP queue deconfigured: Deconfiguring an AP adapter
resets all of its queues, so this is handled by indicating the reset
verification completed successfully.
2. For all response codes other than 0 (normal reset completion), 2
(queue reset in progress) and 3 (AP deconfigured), the -EIO error will
be returned from the vfio_ap_mdev_reset_queue() function. In all cases,
all fields of the status word other than the response code will be
set to zero, so it makes no sense to check status bits.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230118203111.529766-6-akrowiak@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Verification that the asynchronous ZAPQ function has completed only needs
to be done when the response code indicates the function was successfully
initiated; so, let's call the apq_reset_check function immediately after
the response code zero is returned from the ZAPQ.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230118203111.529766-5-akrowiak@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
To eliminate the repeated calls to the PQAP(ZAPQ) function to verify that
a reset in progress completed successfully and ensure that error response
codes get appropriately logged, let's call the apq_reset_check() function
when the ZAPQ response code indicates that a reset that is already in
progress.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230118203111.529766-4-akrowiak@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The vfio_ap_mdev_reset_queue() function does not check the status
response code returned form the PQAP(TAPQ) function when verifying the
queue's status; consequently, there is no way of knowing whether
verification failed because the wait time was exceeded, or because the
PQAP(TAPQ) failed.
This patch adds a function to check the status response code from the
PQAP(TAPQ) instruction and logs an appropriate message if it fails.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230118203111.529766-3-akrowiak@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The vfio_ap_mdev_reset_queue() function contains a loop to verify that the
reset successfully completes within 40ms. This patch moves that loop into
a separate function.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230118203111.529766-2-akrowiak@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
css_schedule_reprobe() function calls the evaluation for CSS_EVAL_UNREG
which is specific to the idset of unregistered subchannels. This
evaluation was introduced because, previously, if the underlying device
become not-accessible, the subchannel was unregistered. But, in the recent
changes in cio,with the commit '2297791c92d0 s390/cio: dont unregister
subchannel from child-drivers', we no longer unregister the subchannels
just because of a non-operational device. This allows to have subchannels
without any operational device connected on it. So, a css_schedule_reprobe
function on unregistered subchannel does not have any effect.
Change this functionality to evaluate the subchannels which does not
have a working path to the device. This could be due the erroneous
device or due to the erraneous path. Evaluate based on the values of OPM
and PAM&POM.
Here we introduced a new idset function,to keep I/O subchannels in the
idset when the last seen status indicates that the device has no working
path. A device has no working path if all available paths have been tried
without success.A failed I/O attempt on a path is indicated as a 0 bit
value in the POM mask. By looking at the POM mask bit values of available
paths (1 in PAM) that Linux is supposed to use (1 in vary mask OPM), we
can identify a non-working device as a device where the bit-wise and of
the PAM, POM and OPM mask return 0.
css_schedule_reprobe() is being used by dasd-driver and chsc-cio
component. dasd driver, when it detects a change in the pathgroup, invokes
the re-evaluation of the subchannel. And chsc-cio component upon a CRW
event, (resource accessibility event). In both the cases, it makes much
better sense to re-evalute the subchannel with no-valid path.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reported-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Tested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Fix a resource leak if an error occurs.
Fixes: f404ca4c7ea8 ("IB/hfi1: Refactor hfi_user_exp_rcv_setup() IOCTL")
Signed-off-by: Dean Luick <dean.luick@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Link: https://lore.kernel.org/r/167354736291.2132367.10894218740150168180.stgit@awfm-02.cornelisnetworks.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
The patch that fixed string control support somehow got mangled when it was
merged in mainline: the added line ended up in the wrong place.
Fix this.
Fixes: 73278d483378 ("media: v4l2-ctrls-api.c: add back dropped ctrl->is_new = 1")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc and other subsystem driver fixes for
6.2-rc5 to resolve a few reported issues. They include:
- long time pending fastrpc fixes (should have gone into 6.1, my
fault)
- mei driver/bus fixes and new device ids
- interconnect driver fixes for reported problems
- vmci bugfix
- w1 driver bugfixes for reported problems
Almost all of these have been in linux-next with no reported problems,
the rest have all passed 0-day bot testing in my tree and on the
mailing lists where they have sat too long due to me taking a long
time to catch up on my pending patch queue"
* tag 'char-misc-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
VMCI: Use threaded irqs instead of tasklets
misc: fastrpc: Pass bitfield into qcom_scm_assign_mem
gsmi: fix null-deref in gsmi_get_variable
misc: fastrpc: Fix use-after-free race condition for maps
misc: fastrpc: Don't remove map on creater_process and device_release
misc: fastrpc: Fix use-after-free and race in fastrpc_map_find
misc: fastrpc: fix error code in fastrpc_req_mmap()
mei: me: add meteor lake point M DID
mei: bus: fix unlink on bus in error path
w1: fix WARNING after calling w1_process()
w1: fix deadloop in __w1_remove_master_device()
comedi: adv_pci1760: Fix PWM instruction handling
interconnect: qcom: rpm: Use _optional func for provider clocks
interconnect: qcom: msm8996: Fix regmap max_register values
interconnect: qcom: msm8996: Provide UFS clocks to A2NoC
dt-bindings: interconnect: Add UFS clocks to MSM8996 A2NoC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are three small driver and kernel core fixes for 6.2-rc5. They
include:
- potential gadget fixup in do_prlimit
- device property refcount leak fix
- test_async_probe bugfix for reported problem"
* tag 'driver-core-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
prlimit: do_prlimit needs to have a speculation check
driver core: Fix test_async_probe_init saves device in wrong array
device property: fix of node refcount leak in fwnode_graph_get_next_endpoint()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for 6.2-rc5. It resolves a build
issue reported and Fixed by Arnd in the vc04_services driver. It's
been in linux-next this week with no reported problems"
* tag 'staging-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vchiq_arm: fix enum vchiq_status return types
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.2-rc5 that
resolve a number of tiny reported issues and some new device ids. They
include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing"
* tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: exar: Add support for Sealevel 7xxxC serial cards
Revert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler"
tty: serial: qcom_geni: avoid duplicate struct member init
serial: atmel: fix incorrect baudrate setup
tty: fix possible null-ptr-defer in spk_ttyio_release
serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler
serial: amba-pl011: fix high priority character transmission in rs486 mode
serial: pch_uart: Pass correct sg to dma_unmap_sg()
tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt fixes from Greg KH:
"Here are a number of small USB and Thunderbolt driver fixes and new
device id changes for 6.2-rc5. Included in here are:
- thunderbolt bugfixes for reported problems
- new usb-serial driver ids added
- onboard_hub usb driver fixes for much-reported problems
- xhci bugfixes
- typec bugfixes
- ehci-fsl driver module alias fix
- iowarrior header size fix
- usb gadget driver fixes
All of these, except for the iowarrior fix, have been in linux-next
with no reported issues. The iowarrior fix passed the 0-day testing
and is a one digit change based on a reported problem in the driver
(which was written to a spec, not the real device that is now
available)"
* tag 'usb-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
USB: misc: iowarrior: fix up header size for USB_DEVICE_ID_CODEMERCS_IOW100
usb: host: ehci-fsl: Fix module alias
usb: dwc3: fix extcon dependency
usb: core: hub: disable autosuspend for TI TUSB8041
USB: fix misleading usb_set_intfdata() kernel doc
usb: gadget: f_ncm: fix potential NULL ptr deref in ncm_bitrate()
USB: gadget: Add ID numbers to configfs-gadget driver names
usb: typec: tcpm: Fix altmode re-registration causes sysfs create fail
usb: gadget: g_webcam: Send color matching descriptor per frame
usb: typec: altmodes/displayport: Use proper macro for pin assignment check
usb: typec: altmodes/displayport: Fix pin assignment calculation
usb: typec: altmodes/displayport: Add pin assignment helper
usb: gadget: f_fs: Ensure ep0req is dequeued before free_request
usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait
usb: misc: onboard_hub: Move 'attach' work to the driver
usb: misc: onboard_hub: Invert driver registration order
usb: ucsi: Ensure connector delayed work items are flushed
usb: musb: fix error return code in omap2430_probe()
usb: chipidea: core: fix possible constant 0 if use IS_ERR(ci->role_switch)
xhci: Detect lpm incapable xHC USB3 roothub ports from ACPI tables
...
|
|
+/-1200uT is a MAGN sensor full measurement range. Magnetometer scale
is the magnetic sensitivity parameter. It is referenced as 0.1uT
according to datasheet and magnetometer channel unit is Gauss in
sysfs-bus-iio documentation. Gauss and uTesla unit conversion
relationship as follows: 0.1uT = 0.001Gs.
Set magnetometer scale and available magnetometer scale as fixed 0.001Gs.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
FXOS8700_CTRL_ODR_MIN is not used but value is probably wrong.
Remove it for a good readability.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-4-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The absence of correct offset leads a failed initialization ODR mode
assignment.
Select MAX ODR mode as the initialization ODR mode by field mask and
FIELD_PREP.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-3-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The absence of a correct offset leads an incorrect ODR mode
readback after use a hexadecimal number to mark the value from
FXOS8700_CTRL_REG1.
Get ODR mode by field mask and FIELD_GET clearly and conveniently.
And attach other additional fix for keeping the original code logic
and a good readability.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-2-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Commit c1e62062ff54 ("iio: light: cm32181: Handle CM3218 ACPI devices
with 2 I2C resources") creates a second client for the actual I2C
address, but the "struct device" passed to PM ops is the first I2C
client that can't talk to the sensor.
That means the I2C transfers in both suspend and resume routines can
fail and blocking the whole suspend process.
Instead of using the first client for I2C transfer, use the I2C client
stored in the cm32181 private struct so the PM ops can get the correct
I2C client to really talk to the sensor device.
Fixes: 68c1b3dd5c48 ("iio: light: cm32181: Add PM support")
BugLink: https://bugs.launchpad.net/bugs/1988346
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2152281
Tested-by: Wahaj <wahajaved@protonmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230118170422.339619-1-kai.heng.feng@canonical.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
If one of ports in the ethernet-ports was disabled, this driver
failed to probe all ports. So, fix it.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230120001959.1059850-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
